| Age | Commit message (Collapse) | Author |
|---|
|
The chip can drive 2 sets of RGB leds. Controller can
be controlled via PWM, I2C and audio synchronisation.
This driver uses I2C to communicate with the chip.
Datasheet: http://www.ti.com/lit/gpn/lp3952
Signed-off-by: Tony Makkiel <tony.makkiel@daqri.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
There is only one x86 hardware where the driver leds-ss4200 applies to.
Add kconfig dependency to x86 architecture, fix help text whitespace.
Signed-off-by: Martin Dummer <martin.dummer@gmx.net>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Significant refactoring of Dell laptop drivers, modularizing the
smbios code. Multiple new platforms added for ideapad, asus, dell,
and alienware using existing quirks. A few fixes and cleanups.
hp-wmi:
- Remove GPS rfkill support via pre-2009 interface
- fix unregister order in hp_wmi_rfkill_setup() once again
ideapad-laptop:
- Add ideapad Y700 (15) to the no_hw_rfkill DMI list
fujitsu-laptop:
- Support radio toggle button
intel-hid:
- allocate correct amount of memory for private struct
platform/x86:
- Make intel_scu_ipc explicitly non-modular
intel_pmc_ipc:
- Avoid pending IPC1 command during legacy suspend
- Fix GCR register base address and length
asus-nb-wmi:
- add wapf=4 quirk for ASUS X75VD
intel_telemetry_pltdrv:
- Change verbosity control bits
dell-rbtn:
- Add a comment about the XPS 13 9350
dell-wmi, dell-laptop:
- depends DMI
dell-wmi:
- support Dell Inspiron M5110
- properly process Dell Instant Launch hotkey
- enable receiving WMI events on Dell Vostro V131
- Support new hotkeys on the XPS 13 9350 (Skylake)
- Clean up hotkey table size check
- Stop storing pointers to DMI tables
dell-laptop:
- move dell_smi_error() to dell-smbios
- use dell_smbios_find_token() instead of find_token_location()
- use dell_smbios_find_token() instead of find_token_id()
- extract SMBIOS-related code to a separate module
dell-smbios:
- rename dell_smi_error() to dell_smbios_error()
- make da_tokens static
- remove find_token_{id,location}()
- implement new function for finding DMI table 0xDA tokens
- make the SMBIOS buffer static
- return the SMBIOS buffer from dell_smbios_get_buffer()
- don't return an SMBIOS buffer from dell_smbios_send_request()
- don't pass an SMBIOS buffer to dell_smbios_send_request()
- rename dell_send_request() to dell_smbios_send_request()
- rename release_buffer() to dell_smbios_release_buffer()
- rename clear_buffer() to dell_smbios_clear_buffer()
- rename get_buffer() to dell_smbios_get_buffer()
dell-led:
- use dell_smbios_send_request() for performing SMBIOS calls
- use dell_smbios_find_token() for finding mic DMI tokens
toshiba_acpi:
- Add a module parameter to disable hotkeys registration
- Add sysfs entries for the Cooling Method feature
- Add support for cooling method feature
Documentation/ABI:
- Update sysfs-driver-toshiba_acpi file
thinkpad_acpi:
- Remove ambiguous logging for "Unsupported brightness interface"
alienware-wmi:
- whitespace improvements
- Add support for two new systems: ASM200 and ASM201.
- Add support for deep sleep control.
- Add initial support for alienware graphics amplifier.
- Add support for new platform: X51-R3
- Clean up whitespace for ASM100 platform"
* tag 'platform-drivers-x86-v4.6-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: (47 commits)
hp-wmi: Remove GPS rfkill support via pre-2009 interface
hp-wmi: fix unregister order in hp_wmi_rfkill_setup() once again
dell-wmi: support Dell Inspiron M5110
dell-wmi: properly process Dell Instant Launch hotkey
dell-wmi: enable receiving WMI events on Dell Vostro V131
dell-smbios: rename dell_smi_error() to dell_smbios_error()
dell-laptop: move dell_smi_error() to dell-smbios
ideapad-laptop: Add ideapad Y700 (15) to the no_hw_rfkill DMI list
fujitsu-laptop: Support radio toggle button
intel-hid: allocate correct amount of memory for private struct
platform/x86: Make intel_scu_ipc explicitly non-modular
intel_pmc_ipc: Avoid pending IPC1 command during legacy suspend
intel_pmc_ipc: Fix GCR register base address and length
asus-nb-wmi: add wapf=4 quirk for ASUS X75VD
intel_telemetry_pltdrv: Change verbosity control bits
dell-rbtn: Add a comment about the XPS 13 9350
dell-wmi: Support new hotkeys on the XPS 13 9350 (Skylake)
dell-wmi: Clean up hotkey table size check
dell-wmi, dell-laptop: depends DMI
dell-wmi: Stop storing pointers to DMI tables
...
|
|
With the advent of dell_smbios_find_token(), dell-led does not need to
perform any DMI walking on its own, but it can rather ask dell-smbios to
look up the DMI tokens it needs for changing the state of the microphone
LED.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
|
|
Si-En Technology was acquired by ISSI in 2011, and it appears that
the IS31FL3218/IS31FL3216 are just rebranded SN3218/SN3216 devices.
Add the "si-en,sn3218" and "si-en,sn3216" compatible strings into the
IS31FL32XX driver as aliases for the issi equivalents, and update
binding documentation.
Datasheets:
IS31FL3218: http://www.issi.com/WW/pdf/31FL3218.pdf
SN3218: http://www.si-en.com/uploadpdf/s2011517171720.pdf
IS31FL3216: http://www.issi.com/WW/pdf/31FL3216.pdf
SN3216: http://www.si-en.com/uploadpdf/SN3216201152410148.pdf
Signed-off-by: David Rivshin <drivshin@allworx.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
The IS31FL32xx family of LED controllers are I2C devices with multiple
constant-current channels, each with independent 256-level PWM control.
Datasheets: http://www.issi.com/US/product-analog-fxled-driver.shtml
This has been tested on the IS31FL3236 and IS31FL3216, on an ARM
(TI am335x) platform.
The programming paradigm of these devices is similar in the following
ways:
- All registers are 8 bit
- All LED control registers are write-only
- Each LED channel has a PWM register (0-255)
- PWM register writes are shadowed until an Update register is poked
- All have a concept of Software Shutdown, which disables output
However, there are some differences in devices:
- 3236/3235 have a separate Control register for each LED,
(3218/3216 pack the enable bits into fewer registers)
- 3236/3235 have a per-channel current divisor setting
- 3236/3235 have a Global Control register that can turn off all LEDs
- 3216 is unique in a number of ways
- OUT9-OUT16 can be configured as GPIOs instead of LED controls
- LEDs can be programmed with an 8-frame animation, with
programmable delay between frames
- LEDs can be modulated by an input audio signal
- Max output current can be adjusted from 1/4 to 2x globally
- Has a Configuration register instead of a Shutdown register
This driver currently only supports the base PWM control function
of these devices. The following features of these devices are not
implemented, although it should be possible to add them in the future:
- All devices are capable of going into a lower-power "software
shutdown" mode.
- The is31fl3236 and is31fl3235 can reduce the max output current
per-channel with a divisor of 1, 2, 3, or 4.
- The is31fl3216 can use some LED channels as GPIOs instead.
- The is31fl3216 can animate LEDs in hardware.
- The is31fl3216 can modulate LEDs according to an audio input.
- The is31fl3216 can reduce/increase max output current globally.
Signed-off-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Ran into this on UML:
drivers/built-in.o: In function `bcm6328_leds_probe':
drivers/leds/leds-bcm6328.c:340: undefined reference to `devm_ioremap_resource'
drivers/built-in.o: In function `bcm6358_leds_probe':
drivers/leds/leds-bcm6358.c:173: undefined reference to `devm_ioremap_resource'
collect2: error: ld returned 1 exit status
devm_ioremap_resource() is defined only when HAS_IOMEM is selected.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Fixes the following randconfig problem
leds-sead3.c:(.text+0x7dc): undefined reference to `led_classdev_unregister'
leds-sead3.c:(.text+0x7e8): undefined reference to `led_classdev_unregister'
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-leds@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
The commit [b67893206fc0: leds:lp55xx: fix firmware loading error]
tries to address the firmware file handling with user helper, but it
sets a wrong Kconfig CONFIG_FW_LOADER_USER_HELPER_FALLBACK. Since the
wrong option was enabled, the system got a regression -- it suffers
from the unexpected long delays for non-present firmware files.
This patch corrects the Kconfig dependency to the right one,
CONFIG_FW_LOADER_USER_HELPER. This doesn't change the fallback
behavior but only enables UMH when needed.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=944661
Fixes: b67893206fc0 ('leds:lp55xx: fix firmware loading error')
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Fix missing Kconfig LEDS_CLASS dependency.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
- Stop using LP855X Platform Data to control regulators
- Move PWM8941 WLED driver into Backlight
- Remove invalid use of IS_ERR_VALUE() macro
- Remove duplicate check for NULL data before unregistering
- Export I2C Device ID structure
* tag 'backlight-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: tosa: Export I2C module alias information
backlight: lp8788_bl: Delete a check before backlight_device_unregister()
backlight: sky81452: Remove unneeded use of IS_ERR_VALUE() macro
backlight: pm8941-wled: Move PM8941 WLED driver to backlight
backlight: lp855x: Use private data for regulator control
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask
from Benjamin Herrenschmidt
- EEH fixes for SRIOV from Gavin
- introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth
- use hardware RNG for arch_get_random_seed_* not arch_get_random_*
from Paul Mackerras
- seccomp filter support from Michael Ellerman
- opal_cec_reboot2() handling for HMIs & machine checks from Mahesh
Salgaonkar
- add powerpc timebase as a trace clock source from Naveen N. Rao
- misc cleanups in the xmon, signal & SLB code from Anshuman Khandual
- add an inline function to update POWER8 HID0 from Gautham R. Shenoy
- fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman
- drop support for 64K local store on 4K kernels from Michael Ellerman
- move dma_get_required_mask() from pnv_phb to pci_controller_ops from
Andrew Donnellan
- initialize distance lookup table from drconf path from Nikunj A
Dadhania
- enable RTC class support from Vaibhav Jain
- disable automatically blocked PCI config from Gavin Shan
- add LEDs driver for PowerNV platform from Vasant Hegde
- fix endianness issues in the HVSI driver from Laurent Dufour
- kexec endian fixes from Samuel Mendoza-Jonas
- fix corrupted pdn list from Gavin Shan
- fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan
- Freescale updates from Scott: Highlights include 32-bit memcpy/memset
optimizations, checksum optimizations, 85xx config fragments and
updates, device tree updates, e6500 fixes for non-SMP, and misc
cleanup and minor fixes.
- a ton of cxl updates & fixes:
- add explicit precision specifiers from Rasmus Villemoes
- use more common format specifier from Rasmus Villemoes
- destroy cxl_adapter_idr on module_exit from Johannes Thumshirn
- destroy afu->contexts_idr on release of an afu from Johannes
Thumshirn
- compile with -Werror from Daniel Axtens
- EEH support from Daniel Axtens
- plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain
- add alternate MMIO error handling from Ian Munsie
- allow release of contexts which have been OPENED but not STARTED
from Andrew Donnellan
- remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar
- release irqs if memory allocation fails from Vaibhav Jain
- remove racy attempt to force EEH invocation in reset from Daniel
Axtens
- fix + cleanup error paths in cxl_dev_context_init from Ian Munsie
- fix force unmapping mmaps of contexts allocated through the kernel
api from Ian Munsie
- set up and enable PSL Timebase from Philippe Bergheaud
* tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (140 commits)
cxl: Set up and enable PSL Timebase
cxl: Fix force unmapping mmaps of contexts allocated through the kernel api
cxl: Fix + cleanup error paths in cxl_dev_context_init
powerpc/eeh: Fix fenced PHB caused by eeh_slot_error_detail()
powerpc/pseries: Cleanup on pci_dn_reconfig_notifier()
powerpc/pseries: Fix corrupted pdn list
powerpc/powernv: Enable LEDS support
powerpc/iommu: Set default DMA offset in dma_dev_setup
cxl: Remove racy attempt to force EEH invocation in reset
cxl: Release irqs if memory allocation fails
cxl: Remove use of macro DEFINE_PCI_DEVICE_TABLE
powerpc/powernv: Fix mis-merge of OPAL support for LEDS driver
powerpc/powernv: Reset HILE before kexec_sequence()
powerpc/kexec: Reset secondary cpu endianness before kexec
powerpc/hvsi: Fix endianness issues in the HVSI driver
leds/powernv: Add driver for PowerNV platform
powerpc/powernv: Create LED platform device
powerpc/powernv: Add OPAL interfaces for accessing and modifying system LED states
powerpc/powernv: Fix the log message when disabling VF
cxl: Allow release of contexts which have been OPENED but not STARTED
...
|
|
The leds-ns2 driver is also used by the n090401 board (Seagate NAS
4-Bay), which is based on the Marvell Armada-370 SoC.
Then this patch allows to select the leds-ns2 driver if MACH_ARMADA_370
is enabled. Additionally, this also updates the Kconfig help message.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
If COMPILE_TEST is enabled, relax the dependency on GPIOLIB for the
recently introduced symbols LEDS_AAT1290 and LEDS_KTD2692.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
The Qualcomm PM8941 WLED block is used for backlight and should therefor
be in the backlight framework and not in the LED framework. This moves
the driver and adapts to the backlight api instead.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Tested-by: Rob Clark <robdclark@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch implements LED driver for PowerNV platform using the existing
generic LED class framework.
PowerNV platform has below type of LEDs:
- System attention
Indicates there is a problem with the system that needs attention.
- Identify
Helps the user locate/identify a particular FRU or resource in the
system.
- Fault
Indicates there is a problem with the FRU or resource at the
location with which the indicator is associated.
We register classdev structures for all individual LEDs detected on the
system through LED specific device tree nodes. Device tree nodes specify
what all kind of LEDs present on the same location code. It registers
LED classdev structure for each of them.
All the system LEDs can be found in the same regular path /sys/class/leds/.
We don't use LED colors. We use LED node and led-types property to form
LED classdev. Our LEDs have names in this format.
<location_code>:<attention|identify|fault>
Any positive brightness value would turn on the LED and a zero value would
turn off the LED. The driver will return LED_FULL (255) for any turned on
LED and LED_OFF (0) for any turned off LED.
The platform level implementation of LED get and set state has been
achieved through OPAL calls. These calls are made available for the
driver by exporting from architecture specific codes.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Tested-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds
Pull LED subsystem updates from Bryan Wu:
"In this cycle, we finished to merge patches for LED Flash class
driver.
Other than that we have some bug fixes and new drivers for LED
controllers"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (33 commits)
leds:lp55xx: fix firmware loading error
leds: fix max77693-led build errors
leds: fix aat1290 build errors
leds: aat1290: pass flags parameter to devm_gpiod_get
leds: ktd2692: pass flags parameter to devm_gpiod_get
drivers/leds: don't use module_init in non-modular leds-cobalt-raq.c
leds: aat1290: add support for V4L2 Flash sub-device
DT: aat1290: Document handling external strobe sources
leds: max77693: add support for V4L2 Flash sub-device
media: Add registration helpers for V4L2 flash sub-devices
v4l: async: Add a pointer to of_node to struct v4l2_subdev, match it
Documentation: leds: Add description of v4l2-flash sub-device
leds: add BCM6358 LED driver
leds: add DT binding for BCM6358 LED controller
leds: fix brightness changing when software blinking is active
Documentation: leds-lp5523: describe master fader attributes
leds: lp5523: add master_fader support
leds: leds-gpio: Allow compile test if !GPIOLIB
leds: leds-gpio: Add missing #include <linux/of.h>
gpiolib: Add missing dummies for the unified device properties interface
...
|
|
LP55xx driver uses not firmware file but raw data to load program through
the firmware interface.(Documents/leds/leds-lp55xx.txt)
For example, here is how to run blinking green channel pattern.
(The second engine is seleted and MUX is mapped to 'RGB' mode)
echo 2 > /sys/bus/i2c/devices/xxxx/select_engine
echo "RGB" > /sys/bus/i2c/devices/xxxx/engine_mux
echo 1 > /sys/class/firmware/lp5562/loading
echo "4000600040FF6000" > /sys/class/firmware/lp5562/data
echo 0 > /sys/class/firmware/lp5562/loading
echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
However, '/sys/class/firmware/<device name>' is not created after the
firmware loader user helper was introduced.
This feature is used in the case below.
As soon as the firmware download is requested by the driver, firmware
class subsystem tries to find the binary file.
If it gets failed, then it just falls back to user helper to load
raw data manually. Here, you can see the device file under
/sys/class/firmware/.
To make it happen, LP55xx driver requires two configurations.
1. Enable CONFIG_FW_LOADER_USER_HELPER_FALLBACK in Kconfig
2. Set option, 'FW_OPT_USERHELPER' on requesting the firmware data.
It means the second option should be 'false' in
request_firmware_nowait().
This option enables to load firmware data manually by calling
fw_load_from_user_helper().
Cc: linux-leds@vger.kernel.org
Signed-off-by: Milo Kim <milo.kim@ti.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Fix build errors when LEDS_MAX77693=y and V4L2_FLASH_LED_CLASS=m
by restricting LEDS_MAX77693 to =m if V4L2_FLASH_LED_CLASS=m.
drivers/leds/leds-max77693.c:1062: undefined reference to `v4l2_flash_release'
drivers/leds/leds-max77693.c:1068: undefined reference to `v4l2_flash_release'
drivers/built-in.o: In function `max77693_register_led':
drivers/leds/leds-max77693.c:968: undefined reference to `v4l2_flash_init'
drivers/built-in.o: In function `max77693_led_probe':
drivers/leds/leds-max77693.c:1048: undefined reference to `v4l2_flash_release'
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Fix build errors when LEDS_AAT1290=y and V4L2_FLASH_LED_CLASS=m
by restricting LEDS_AAT1290 to =m if V4L2_FLASH_LED_CLASS=m.
drivers/built-in.o: In function `aat1290_led_remove':
leds-aat1290.c:(.text+0xe5d77): undefined reference to `v4l2_flash_release'
drivers/built-in.o: In function `aat1290_led_probe':
leds-aat1290.c:(.text+0xe6494): undefined reference to `v4l2_flash_init'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem updates from Dmitry Torokhov:
"Thanks to Samuel Thibault input device (keyboard) LEDs are no longer
hardwired within the input core but use LED subsystem and so allow use
of different triggers; Hans de Goede did a large update for the ALPS
touchpad driver; we have new TI drv2665 haptics driver and DA9063
OnKey driver, and host of other drivers got various fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (55 commits)
Input: pixcir_i2c_ts - fix receive error
MAINTAINERS: remove non existent input mt git tree
Input: improve usage of gpiod API
tty/vt/keyboard: define LED triggers for VT keyboard lock states
tty/vt/keyboard: define LED triggers for VT LED states
Input: export LEDs as class devices in sysfs
Input: cyttsp4 - use swap() in cyttsp4_get_touch()
Input: goodix - do not explicitly set evbits in input device
Input: goodix - export id and version read from device
Input: goodix - fix variable length array warning
Input: goodix - fix alignment issues
Input: add OnKey driver for DA9063 MFD part
Input: elan_i2c - add product IDs FW names
Input: elan_i2c - add support for multi IC type and iap format
Input: focaltech - report finger width to userspace
tty: remove platform_sysrq_reset_seq
Input: synaptics_i2c - use proper boolean values
Input: psmouse - use true instead of 1 for boolean values
Input: cyapa - fix a few typos in comments
Input: stmpe-ts - enforce device tree only mode
...
|
|
Add support for V4L2 Flash sub-device to the aat1290 LED Flash class
driver. The support allows for V4L2 Flash sub-device to take the control
of the LED Flash class device.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
This change creates a new input handler called "leds" that exports LEDs on input
devices as standard LED class devices in sysfs and allows controlling their
state via sysfs or via any of the standard LED triggers. This allows to
re-purpose and reassign LDEs on the keyboards to represent states other
than the standard keyboard states (CapsLock, NumLock, etc).
The old API of controlling input LEDs by writing into /dev/input/eventX
devices is still present and will take precedence over accessing via LEDs
subsystem (i.e. it may override state set by a trigger). If input device is
"grabbed" then requests coming through LED subsystem will be ignored.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This adds support for the LED controller on Broadcom's BCM6358.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency of LEDS_GPIO on GPIOLIB if COMPILE_TEST is
enabled.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
This patch adds a driver to support the ktd2692 flash LEDs.
ktd2692 can control flash current by ExpressWire interface.
Signed-off-by: Ingi Kim <ingi2.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
This adds support for the LED controller on Broadcom's BCM6328.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
This patch adds a driver for the 1.5A Step-Up Current Regulator
for Flash LEDs. The device is programmed through a Skyworks proprietary
AS2Cwire serial digital interface.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
This patch adds led-flash support to Maxim max77693 chipset.
A device can be exposed to user space through LED subsystem
sysfs interface. Device supports up to two leds which can
work in flash and torch mode. The leds can be triggered
externally or by software.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
The TLC59116 is an I2C bus controlled 16-channel LED driver. The
TLC59108 is an I2C bus controlled 8-channel LED driver, which is very
similar to the TLC59116. Each LED output has its own 8-bit
fixed-frequency PWM controller to control the brightness of the LED.
The LEDs can also be fixed off and on, making them suitable for use as
GPOs.
This is based on a driver from Belkin, but has been extensively
rewritten and extended to support both 08 and 16 versions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Imre Kaloz <kaloz@openwrt.org>
Cc: Matthew.Fatheree@belkin.com
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
This adds support for the WLED ('White' LED) block on Qualcomm's
PM8941 PMICs.
(cooloney@gmail.com: remove unneeded semicolon)
Signed-off-by: Courtney Cavin <courtney.cavin@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Some LED devices support two operation modes - torch and flash.
This patch provides support for flash LED devices in the LED subsystem
by introducing new sysfs attributes and kernel internal interface.
The attributes being introduced are: flash_brightness, flash_strobe,
flash_timeout, max_flash_timeout, max_flash_brightness, flash_fault,
flash_sync_strobe and available_sync_leds. All the flash related
features are placed in a separate module.
The modifications aim to be compatible with V4L2 framework requirements
related to the flash devices management. The design assumes that V4L2
sub-device can take of the LED class device control and communicate
with it through the kernel internal interface. When V4L2 Flash sub-device
file is opened, the LED class device sysfs interface is made
unavailable.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
The driver should select REGMAP_I2C rather than depend on it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Introduce the Texas Instruments lp8860
4 channel LED driver.
This driver configures the device in display cluster mode
as this seems to be the most used configuration at the
time of the driver configuration.
For more product information please see the link below:
http://www.ti.com/product/lp8860-q1
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver for menf21bmc.
- convert k10temp, smsc47b397, da9052, da9055 to new hwmon API.
- register ntc_thermistor driver with thermal subsystem.
- add support for F15h M60h to k10temp driver.
- add driver for MEN14F021P00 BMC HWMON driver; this required a merge
with tag mfd-hwmon-leds-watchdog-v3.18
* tag 'hwmon-for-linus-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ab8500) Call kernel_power_off instead of pm_power_off
hwmon: (menf21bmc) Introduce MEN14F021P00 BMC HWMON driver
leds: leds-menf21bmc: Introduce MEN 14F021P00 BMC LED driver
watchdog: menf21bmc_wdt: Introduce MEN 14F021P00 BMC Watchdog driver
mfd: menf21bmc: Introduce MEN 14F021P00 BMC MFD Core driver
hwmon: (ntc_thermistor) Add ntc thermistor to thermal subsystem as a sensor.
hwmon: (smsc47b397) Convert to devm_hwmon_device_register_with_groups
MAINTAINERS: add entry for the PWM fan driver
hwmon: (k10temp) Convert to devm_hwmon_device_register_with_groups
hwmon: (k10temp) Add support for F15h M60h
hwmon: (da9052) Convert to devm_hwmon_device_register_with_groups
hwmon: (da9055) Convert to devm_hwmon_device_register_with_groups
hwmon: (ads1015) Use of_property_read_u32 at appropriate places
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
Most of the new code is for the Keystone Navigator driver, which is
new base support that is going to be needed for their hardware
accelerated network driver and other units.
Most of the commits are for moving old code around from at91 and omap
for things that are done in device drivers nowadays.
- at91: move reset, poweroff, memory and clocksource code into
drivers directories
- socfpga: add edac driver (through arm-soc, as requested by Boris)
- omap: move omap-intc code to drivers/irqchip
- sunxi: added an RTC driver for sun6i
- omap: mailbox driver related changes
- keystone: support for the "Navigator" component
- versatile: new reboot, led and soc drivers"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (92 commits)
bus: arm-ccn: Fix spurious warning message
leds: add device tree bindings for register bit LEDs
soc: add driver for the ARM RealView
power: reset: driver for the Versatile syscon reboot
leds: add a driver for syscon-based LEDs
drivers/soc: ti: fix build break with modules
MAINTAINERS: Add Keystone Multicore Navigator drivers entry
soc: ti: add Keystone Navigator DMA support
Documentation: dt: soc: add Keystone Navigator DMA bindings
soc: ti: add Keystone Navigator QMSS driver
Documentation: dt: soc: add Keystone Navigator QMSS bindings
rtc: sunxi: Depend on platforms sun4i/sun7i that actually have the rtc
rtc: sun6i: Add sun6i RTC driver
irqchip: omap-intc: remove unnecessary comments
irqchip: omap-intc: correct maximum number or MIR registers
irqchip: omap-intc: enable TURBO idle mode
irqchip: omap-intc: enable IP protection
irqchip: omap-intc: remove unnecesary of_address_to_resource() call
irqchip: omap-intc: comment style cleanup
irqchip: omap-intc: minor improvement to omap_irq_pending()
...
|
|
This makes it possible to create a set of LEDs from a syscon
MFD instance, which is lean mean and clean on the ARM
reference designs and can replace the Versatile LEDs driver
in the long run, as well as other custom syscon LEDs drivers.
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
[Fixed cocinelle warnings]
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Added driver to support the 14F021P00 BMC LEDs.
The BMC is a Board Management Controller including four LEDs which
can be switched on and off.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
Use MACH_KIRKWOOD which will be set when kirkwood is built as part of
mach-mvebu.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Link: https://lkml.kernel.org/r/1409417172-6846-5-git-send-email-andrew@lunn.ch
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"A handful of driver-related changes. We've had a bunch of them going
in through other branches as well, so it's only a part of what we
really have this release.
Larger pieces are:
- Removal of a now unused PWM driver for atmel
[ This includes AVR32 changes that have been appropriately acked ]
- Performance counter support for the arm CCN interconnect
- OMAP mailbox driver cleanups and consolidation
- PCI and SATA PHY drivers for SPEAr 13xx platforms
- Redefinition (with backwards compatibility!) of PCI DT bindings for
Tegra to better model regulators/power"
Note: this merge also fixes up the semantic conflict with the new
calling convention for devm_phy_create(), see commit f0ed817638b5 ("phy:
core: Let node ptr of PHY point to PHY and not of PHY provider") that
came in through Greg's USB tree.
Semantic merge patch by Stephen Rothwell <sfr@canb.auug.org.au> through
the next tree.
* tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: arm-ccn: Fix error handling at event allocation
mailbox/omap: add a parent structure for every IP instance
mailbox/omap: remove the private mailbox structure
mailbox/omap: consolidate OMAP mailbox driver
mailbox/omap: simplify the fifo assignment by using macros
mailbox/omap: remove omap_mbox_type_t from mailbox ops
mailbox/omap: remove OMAP1 mailbox driver
mailbox/omap: use devm_* interfaces
bus: ARM CCN: add PERF_EVENTS dependency
bus: ARM CCN PMU driver
PCI: spear: Remove spear13xx_pcie_remove()
PCI: spear: Fix Section mismatch compilation warning for probe()
ARM: tegra: Remove legacy PCIe power supply properties
PCI: tegra: Remove deprecated power supply properties
PCI: tegra: Implement accurate power supply scheme
ARM: SPEAr13xx: Update defconfigs
ARM: SPEAr13xx: Add pcie and miphy DT nodes
ARM: SPEAr13xx: Add bindings and dt node for misc block
ARM: SPEAr13xx: Fix static mapping table
phy: Add drivers for PCIe and SATA phy on SPEAr13xx
...
|
|
This adds a driver for the iPAQ microcontroller LED.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
The leds-atmel-pwm driver is now obsolete. It is not used by any mainlined
boards and is replaced by the generic leds_pwm with the pwm-atmel driver using
the generic PWM framework.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds
Pull LED updates from Bryan Wu:
"I just found merge window is open and I'm quite busy and almost forget
to send out this pull request. Thanks Russell and Alexandre ping me
about this.
So basically we got some clean up and leds-pwm fixing patches from
Russell"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: Remove duplicated OOM message for individual driver
drivers/leds: Replace __get_cpu_var use through this_cpu_ptr
leds: lp55xx: add DT bindings for LP55231
leds: 88pm860x: Fix missing refcount decrement for parent of_node
leds: 88pm860x: Use of_get_child_by_name
leds: leds-pwm: add DT support for LEDs wired to supply
leds: leds-pwm: implement PWM inversion
leds: leds-pwm: convert OF parsing code to use led_pwm_add()
leds: leds-pwm: provide a common function to setup a single led-pwm device
leds: pca9685: Remove leds-pca9685 driver
dell-led: add mic mute led interface
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid into next
Pull HID patches from Jiri Kosina:
- RMI driver for Synaptics touchpads, by Benjamin Tissoires, Andrew
Duggan and Jiri Kosina
- cleanup of hid-sony driver and improved support for Sixaxis and
Dualshock 4, by Frank Praznik
- other usual small fixes and support for new device IDs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (29 commits)
HID: thingm: thingm_fwinfo[] doesn't need to be global
HID: core: add two new usages for digitizer
HID: hid-sensor-hub: new device id and quirk for STM Sensor hub
HID: usbhid: enable NO_INIT_REPORTS quirk for Semico USB Keykoard
HID: hid-sensor-hub: Set report quirk for Microsoft Surface
HID: debug: add labels for HID Sensor Usages
HID: uhid: Use kmemdup instead of kmalloc + memcpy
HID: rmi: do not handle touchscreens through hid-rmi
HID: quirk for Saitek RAT7 and MMO7 mices' mode button
HID: core: fix validation of report id 0
HID: rmi: fix masks for x and w_x data
HID: rmi: fix wrong struct field name
HID: rmi: do not fetch more than 16 bytes in a query
HID: rmi: check for the existence of some optional queries before reading query 12
HID: i2c-hid: hid report descriptor retrieval changes
HID: add missing hid usages
HID: hid-sony - allow 3rd party INTEC controller to turn off all leds
HID: sony: Add blink support to the Sixaxis and DualShock 4 LEDs
HID: sony: Initialize the controller LEDs with a device ID value
HID: sony: Use the controller Bluetooth MAC address as the unique value in the battery name string
...
|
|
'for-3.16/thingm' into for-linus
|
|
I got a build error today, since LEDS_VERSATILE can be built-in while LEDS_CLASS
is a module:
drivers/built-in.o: In function `versatile_leds_probe':
:(.text+0x155020): undefined reference to `led_classdev_register'
I suggest we turn this option into 'tristate' so that the dependency
tracking works correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This driver is replaced by pwm-pca9685 driver and there is no user uses this
driver in current tree. So remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Acked-by: Maximilian Güntner <maximilian.guentner@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux into next/cleanup
Merge Kconfig cleanups from Rob Herring:
Several mach kconfig clean-ups of redundant selects
* tag 'kconfig-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
ARM: qcom: clean-up unneeded kconfig selects
ARM: bcm: clean-up unneeded kconfig selects
ARM: mvebu: clean-up unneeded kconfig selects
+ Linux 3.15-rc2
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch refactors the way the thingm driver registers a blink(1) LED.
In order to make the driver simpler and more standard, drop the "rgb"
sysfs attribute and create one instance of LED class per RGB channel.
Actually, the name of the LED class instance registered for a blink(1)
device is "blink1::ABCD", where ABCD is the last 4 chars of the serial
number. The driver now registers 3 instances per RGB chip, named
"thingmX:{red,green,blue}:ledY" where X is the hidraw minor number and Y
is the RGB chip number (as seen by the firmware).
This patch also uses work queues to defer calls with the device, which
now allows triggers to work as expected with this LED device.
Also remove the brightness structure field and the brightness_get
backend, as it is already handled by the LED class, and changes the
prefix of functions and structures to thingm_ to match the driver name.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
