| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull IRQ chip updates from Ingo Molnar:
"A late irqchips update:
- New TI INTR/INTA set of drivers
- Rewrite of the stm32mp1-exti driver as a platform driver
- Update the IOMMU MSI mapping API to be RT friendly
- A number of cleanups and other low impact fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
iommu/dma-iommu: Remove iommu_dma_map_msi_msg()
irqchip/gic-v3-mbi: Don't map the MSI page in mbi_compose_m{b, s}i_msg()
irqchip/ls-scfg-msi: Don't map the MSI page in ls_scfg_msi_compose_msg()
irqchip/gic-v3-its: Don't map the MSI page in its_irq_compose_msi_msg()
irqchip/gicv2m: Don't map the MSI page in gicv2m_compose_msi_msg()
iommu/dma-iommu: Split iommu_dma_map_msi_msg() in two parts
genirq/msi: Add a new field in msi_desc to store an IOMMU cookie
arm64: arch_k3: Enable interrupt controller drivers
irqchip/ti-sci-inta: Add msi domain support
soc: ti: Add MSI domain bus support for Interrupt Aggregator
irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver
dt-bindings: irqchip: Introduce TISCI Interrupt Aggregator bindings
irqchip/ti-sci-intr: Add support for Interrupt Router driver
dt-bindings: irqchip: Introduce TISCI Interrupt router bindings
gpio: thunderx: Use the default parent apis for {request,release}_resources
genirq: Introduce irq_chip_{request,release}_resource_parent() apis
firmware: ti_sci: Add helper apis to manage resources
firmware: ti_sci: Add RM mapping table for am654
firmware: ti_sci: Add support for IRQ management
firmware: ti_sci: Add support for RM core ops
...
|
|
Pull ARM SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to
multiplatform enabled.
- Cleanups of Davinci
This also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
ARM: debug-ll: add default address for digicolor
ARM: u300: regulator: add MODULE_LICENSE()
ARM: ep93xx: move private headers out of mach/*
ARM: ep93xx: move pinctrl interfaces into include/linux/soc
ARM: ep93xx: keypad: stop using mach/platform.h
ARM: ep93xx: move network platform data to separate header
ARM: stm32: add AMBA support for stm32 family
MAINTAINERS: update arch/arm/mach-davinci
ARM: rockchip: add missing of_node_put in rockchip_smp_prepare_pmu
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
...
|
|
Merge in a few pending fixes from pre-5.1 that didn't get sent in:
MAINTAINERS: update arch/arm/mach-davinci
ARM: dts: ls1021: Fix SGMII PCS link remaining down after PHY disconnect
ARM: dts: imx6q-logicpd: Reduce inrush current on USBH1
ARM: dts: imx6q-logicpd: Reduce inrush current on start
ARM: dts: imx: Fix the AR803X phy-mode
ARM: dts: sun8i: a33: Reintroduce default pinctrl muxing
arm64: dts: allwinner: a64: Rename hpvcc-supply to cpvdd-supply
ARM: sunxi: fix a leaked reference by adding missing of_node_put
ARM: sunxi: fix a leaked reference by adding missing of_node_put
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core/kobject updates from Greg KH:
"Here is the "big" set of driver core patches for 5.2-rc1
There are a number of ACPI patches in here as well, as Rafael said
they should go through this tree due to the driver core changes they
required. They have all been acked by the ACPI developers.
There are also a number of small subsystem-specific changes in here,
due to some changes to the kobject core code. Those too have all been
acked by the various subsystem maintainers.
As for content, it's pretty boring outside of the ACPI changes:
- spdx cleanups
- kobject documentation updates
- default attribute groups for kobjects
- other minor kobject/driver core fixes
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (47 commits)
kobject: clean up the kobject add documentation a bit more
kobject: Fix kernel-doc comment first line
kobject: Remove docstring reference to kset
firmware_loader: Fix a typo ("syfs" -> "sysfs")
kobject: fix dereference before null check on kobj
Revert "driver core: platform: Fix the usage of platform device name(pdev->name)"
init/config: Do not select BUILD_BIN2C for IKCONFIG
Provide in-kernel headers to make extending kernel easier
kobject: Improve doc clarity kobject_init_and_add()
kobject: Improve docs for kobject_add/del
driver core: platform: Fix the usage of platform device name(pdev->name)
livepatch: Replace klp_ktype_patch's default_attrs with groups
cpufreq: schedutil: Replace default_attrs field with groups
padata: Replace padata_attr_type default_attrs field with groups
irqdesc: Replace irq_kobj_type's default_attrs field with groups
net-sysfs: Replace ktype default_attrs field with groups
block: Replace all ktype default_attrs with groups
samples/kobject: Replace foo_ktype's default_attrs field with groups
kobject: Add support for default attribute groups to kobj_type
driver core: Postpone DMA tear-down until after devres release for probe failure
...
|
|
The functions mbi_compose_m{b, s}i_msg may be called from non-preemptible
context. However, on RT, iommu_dma_map_msi_msg() requires to be called
from a preemptible context.
A recent patch split iommu_dma_map_msi_msg in two new functions:
one that should be called in preemptible context, the other does
not have any requirement.
The GICv3 MSI driver is reworked to avoid executing preemptible code in
non-preemptible context. This can be achieved by preparing the MSI
mapping when allocating the MSI interrupt.
Signed-off-by: Julien Grall <julien.grall@arm.com>
[maz: only call iommu_dma_prepare_msi once, fix commit log accordingly]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
ls_scfg_msi_compose_msg() may be called from non-preemptible context.
However, on RT, iommu_dma_map_msi_msg() requires to be called from a
preemptible context.
A recent patch split iommu_dma_map_msi_msg() in two new functions:
one that should be called in preemptible context, the other does
not have any requirement.
The FreeScale SCFG MSI driver is reworked to avoid executing preemptible
code in non-preemptible context. This can be achieved by preparing the
MSI maping when allocating the MSI interrupt.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
its_irq_compose_msi_msg() may be called from non-preemptible context.
However, on RT, iommu_dma_map_msi_msg requires to be called from a
preemptible context.
A recent change split iommu_dma_map_msi_msg() in two new functions:
one that should be called in preemptible context, the other does
not have any requirement.
The GICv3 ITS driver is reworked to avoid executing preemptible code in
non-preemptible context. This can be achieved by preparing the MSI
mapping when allocating the MSI interrupt.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
gicv2m_compose_msi_msg() may be called from non-preemptible context.
However, on RT, iommu_dma_map_msi_msg() requires to be called from a
preemptible context.
A recent change split iommu_dma_map_msi_msg() in two new functions:
one that should be called in preemptible context, the other does
not have any requirement.
The GICv2m driver is reworked to avoid executing preemptible code in
non-preemptible context. This can be achieved by preparing the MSI
mapping when allocating the MSI interrupt.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Add a msi domain that is child to the INTA domain. Clients
uses the INTA MSI bus layer to allocate irqs in this
MSI domain.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Texas Instruments' K3 generation SoCs has an IP Interrupt Aggregator
which is an interrupt controller that does the following:
- Converts events to interrupts that can be understood by
an interrupt router.
- Allows for multiplexing of events to interrupts.
Configuration of the interrupt aggregator registers can only be done by
a system co-processor and the driver needs to send a message to this
co processor over TISCI protocol. Add the required infrastructure to
allow the allocation and routing of these events.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Texas Instruments' K3 generation SoCs has an IP Interrupt Router
that does allows for redirection of input interrupts to host
interrupt controller. Interrupt Router inputs are either from a
peripheral or from an Interrupt Aggregator which is another
interrupt controller.
Configuration of the interrupt router registers can only be done by
a system co-processor and the driver needs to send a message to this
co processor over TISCI protocol.
Add support for Interrupt Router driver over TISCI protocol.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
There is no need to print a message if devm_kzalloc() fails, as the
memory allocation core already takes care of that.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
IRQ_DOMAIN_HIERARCHY selects IRQ_DOMAIN, hence there is no need for
drivers to select both.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Using list_add + list_sort to insert an element and keeping the list
sorted is a somewhat blunt instrument; one can find the right place to
insert in fewer lines of code than the cmp callback uses. Moreover,
walking the entire list afterwards to merge adjacent ranges is
overkill, since we know that only the just-inserted element may be
merged with its neighbours.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
There's no reason to ask kmalloc() to zero the allocation, since all
the fields get initialized immediately afterwards. Except that there's
also not any reason to initialize the ->entry member, since the
element gets added to the lpi_range_list immediately.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
There's no reason to do the allocation of the new lpi_range inside the
lpi_range_lock. One could change the code to avoid the allocation
altogether in case the freed range can be merged with one or two
existing ranges (in which case the allocation would naturally be done
under the lock), but it's probably not worth complicating the code for
that.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
This irqchip driver uses the hwspinlock framework (coprocessor HW regs
access concurrency) for the stm32mp1-exti device.
Hence, this driver needs to handle the hwspinlock driver dependency
using the deferred probe mechanism which requires to move this driver
into a platform one with a probe() ops.
This applies only for the device which is "st,stm32mp1-exti" compatible,
the management of the other devices (st,stm32h7-exti / st,stm32-exti) is
kept unchanged (use IRQCHIP_DECLARE)
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
If interrupts are enabled for a non-root GIC device that uses the
gic-pm driver, when system suspend occurs, the current interrupt
state is not saved and restored correctly and so interrupts do not
work again on resuming the system. Add a late suspend handler to
save and restore the state for these devices.
Suggested-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
gic-pm driver is using pm-clk framework to manage clock resources, where
clocks remain always ON. This happens on Tegra devices which use BPMP
co-processor to manage the clocks. Calls to BPMP are always blocking and
hence it is necessary to enable/disable clocks during prepare/unprepare
phase respectively. When pm-clk is used, prepare count of clock is not
balanced until pm_clk_remove() happens. Clock is prepared in the driver
probe() and thus prepare count of clock remains non-zero, which in turn
keeps clock ON always.
Please note that above mentioned behavior is specific to Tegra devices
using BPMP for clock management and this should not be seen on other
devices. Though this patch uses clk_bulk APIs to address the mentioned
behavior, this works fine for all devices.
To simplify gic_get_clocks() API is removed and instead probe can do
necessary setup.
Suggested-by: Mohan Kumar D <mkumard@nvidia.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The word 'entirely' has been misspelt in a comment in its_msi_prepare().
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
It is useful to print which interrupt controllers are registered in the
system and which parent IRQ they use, especially given that L2 interrupt
controllers do not call request_irq() on their parent interrupt and do
not appear under /proc/interrupts for that reason.
We used to print the base register address virtual address which had
little value, use %pOF to print the path to the Device Tree node which
maps to the physical address more easily and is what people need to
troubleshoot systems.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/soc
This modernizes the IXP4xx platform and adds initial Device Tree
Support. We migrate to MULTI_IRQ_HANDLER, bumps the IRQs to
offset 16, converts to SPARSE_IRQ, then we add proper subsystem
drivers in each subsystem for irqchip, GPIO and clocksource and
switch over to using these new drivers.
Next we modernize the NPE and QMGR drivers and push them down
into drivers/soc.
This has been tested on the IXP4xx NSLU2 and the Gateworks
GW2358-4.
* tag 'ixp4xx-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik: (31 commits)
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
ARM: ixp4xx: Move IXP4xx QMGR and NPE headers
ARM: ixp4xx: Move NPE and QMGR to drivers/soc
ARM: dts: Add some initial IXP4xx device trees
ARM: ixp4xx: Add device tree boot support
ARM: ixp4xx: Add DT bindings
gpio: ixp4xx: Add OF probing support
gpio: ixp4xx: Add DT bindings
clocksource/drivers/ixp4xx: Add OF initialization support
clocksource/drivers/ixp4xx: Add DT bindings
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This adds support for probing and settin up the IXP4xx
irqchip from device tree.
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A couple more MIPS fixes:
- Fix indirect syscall tracing & seccomp filtering for big endian
MIPS64 kernels, which previously loaded the syscall number
incorrectly & would always use zero.
- Fix performance counter IRQ setup for Atheros/ath79 SoCs, allowing
perf to function on those systems.
And not really a fix, but a useful addition:
- Add a Broadcom mailing list to the MAINTAINERS entry for BMIPS
systems to allow relevant engineers to track patch submissions"
* tag 'mips_fixes_5.1_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: perf: ath79: Fix perfcount IRQ assignment
MIPS: scall64-o32: Fix indirect syscall number load
MAINTAINERS: BMIPS: Add internal Broadcom mailing list
|
|
The IXP4xx (arch/arm/mach-ixp4xx) is an old Intel XScale
platform that has very wide deployment and use.
As part of modernizing the platform, we need to implement a
proper irqchip in the irqchip subsystem.
The IXP4xx irqchip is tightly jotted together with the GPIO
controller, and whereas in the past we would deal with this
complex logic by adding necessarily different code, we can
nowadays modernize it using a hierarchical irqchip.
The actual IXP4 irqchip is a simple active low level IRQ
controller, whereas the GPIO functionality resides in a
different memory area and adds edge trigger support for
the interrupts.
The interrupts from GPIO lines 0..12 are 1:1 mapped to
a fixed set of hardware IRQs on this IRQchip, so we
expect the child GPIO interrupt controller to go in and
allocate descriptors for these interrupts.
For the other interrupts, as we do not yet have DT
support for this platform, we create a linear irqdomain
and then go in and allocate the IRQs that the legacy
boards use. This code will be removed on the DT probe
path when we add DT support to the platform.
We add some translation code for supporting DT
translations for the fwnodes, but we leave most of that
for later.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Currently it's not possible to use perf on ath79 due to genirq flags
mismatch happening on static virtual IRQ 13 which is used for
performance counters hardware IRQ 5.
On TP-Link Archer C7v5:
CPU0
2: 0 MIPS 2 ath9k
4: 318 MIPS 4 19000000.eth
7: 55034 MIPS 7 timer
8: 1236 MISC 3 ttyS0
12: 0 INTC 1 ehci_hcd:usb1
13: 0 gpio-ath79 2 keys
14: 0 gpio-ath79 5 keys
15: 31 AR724X PCI 1 ath10k_pci
$ perf top
genirq: Flags mismatch irq 13. 00014c83 (mips_perf_pmu) vs. 00002003 (keys)
On TP-Link Archer C7v4:
CPU0
4: 0 MIPS 4 19000000.eth
5: 7135 MIPS 5 1a000000.eth
7: 98379 MIPS 7 timer
8: 30 MISC 3 ttyS0
12: 90028 INTC 0 ath9k
13: 5520 INTC 1 ehci_hcd:usb1
14: 4623 INTC 2 ehci_hcd:usb2
15: 32844 AR724X PCI 1 ath10k_pci
16: 0 gpio-ath79 16 keys
23: 0 gpio-ath79 23 keys
$ perf top
genirq: Flags mismatch irq 13. 00014c80 (mips_perf_pmu) vs. 00000080 (ehci_hcd:usb1)
This problem is happening, because currently statically assigned virtual
IRQ 13 for performance counters is not claimed during the initialization
of MIPS PMU during the bootup, so the IRQ subsystem doesn't know, that
this interrupt isn't available for further use.
So this patch fixes the issue by simply booking hardware IRQ 5 for MIPS PMU.
Tested-by: Kevin 'ldir' Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: John Crispin <john@phrozen.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
|
|
Currently, when irq_domain_add_linear() fails, the error code does not get
set so it returns zero which is wrong. Fix it by setting the appropriate
error code.
Fixes: 9e543e22e204 ("irqchip: Add driver for Loongson-1 interrupt controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: kernel-janitors@vger.kernel.org
Link: https://lkml.kernel.org/r/20190329062136.GQ32613@kadam
|
|
Parsing entries in an ACPI table had assumed a generic header
structure. There is no standard ACPI header, though, so less common
layouts with different field sizes required custom parsers to go through
their subtable entry list.
Create the infrastructure for adding different table types so parsing
the entries array may be more reused for all ACPI system tables and
the common code doesn't need to be duplicated.
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix sparse warning:
drivers/irqchip/irq-mvebu-sei.c:481:23: warning:
symbol 'mvebu_sei_ap806_caps' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <jason@lakedaemon.net>
Cc: <andrew@lunn.ch>
Cc: <gregory.clement@bootlin.com>
Cc: <sebastian.hesselbarth@gmail.com>
Cc: <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Link: https://lkml.kernel.org/r/20190321151448.15600-1-yuehaibing@huawei.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip updates for 5.1 from Marc Zyngier:
- irqsteer error handling fix
- GICv3 range coalescing fix
- stm32 coprocessor coexistence fixes
- mbigen MSI teardown fix
- non-DT secondary GIC infrastructure removed
- various cleanups (brcmstb-l2, mmp)
- new DT bindings (r8a774c0)
|
|
mbigen_write_msg clears eventid bits of a mbigen register
when free a interrupt, because msi_domain_deactivate memset
struct msg to zero. Then multiple mbigen pins with zero eventid
will report the same interrupt number.
The eventid clear call trace:
free_irq
__free_irq
irq_shutdown
irq_domain_deactivate_irq
__irq_domain_deactivate_irq
__irq_domain_deactivate_irq
msi_domain_deactivate
platform_msi_write_msg
mbigen_write_msg
Signed-off-by: Jianguo Chen <chenjianguo3@huawei.com>
[maz: massaged subject]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The rising configuration status register (rtsr) is not banked.
As it is shared with the co-processor, it should not be written at probe
time, else the co-processor configuration will be lost.
Fixes: f9fc1745501e ("irqchip/stm32: Add host and driver data structures")
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Falling and rising configuration and status registers are not banked.
As they are shared with M4 co-processor, they should not be cleared
at probe time, else M4 co-processor configuration will be lost.
Fixes: f9fc1745501e ("irqchip/stm32: Add host and driver data structures")
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Fix sparse warning:
drivers/irqchip/irq-mmp.c:182:29: warning:
symbol 'mmp_irq_domain_ops' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Fix sparse warnings:
drivers/irqchip/irq-brcmstb-l2.c:278:12: warning:
symbol 'brcmstb_l2_edge_intc_of_init' was not declared. Should it be static?
drivers/irqchip/irq-brcmstb-l2.c:285:12: warning:
symbol 'brcmstb_l2_lvl_intc_of_init' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The lpi_range_list is supposed to be sorted in ascending order of
->base_id (at least if the range merging is to work), but the current
comparison function returns a positive value if rb->base_id >
ra->base_id, which means that list_sort() will put A after B in that
case - and vice versa, of course.
Fixes: 880cb3cddd16 (irqchip/gic-v3-its: Refactor LPI allocator)
Cc: stable@vger.kernel.org (v4.19+)
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
We do not have any in-tree platform with this pathological setup,
and only a single system (Cavium's cns3xxx) isn't DT aware.
Let's drop the secondary GIC support for now, until we remove
the above horror altogether.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- Pseudo NMI support for arm64 using GICv3 interrupt priorities
- uaccess macros clean-up (unsafe user accessors also merged but
reverted, waiting for objtool support on arm64)
- ptrace regsets for Pointer Authentication (ARMv8.3) key management
- inX() ordering w.r.t. delay() on arm64 and riscv (acks in place by
the riscv maintainers)
- arm64/perf updates: PMU bindings converted to json-schema, unused
variable and misleading comment removed
- arm64/debug fixes to ensure checking of the triggering exception
level and to avoid the propagation of the UNKNOWN FAR value into the
si_code for debug signals
- Workaround for Fujitsu A64FX erratum 010001
- lib/raid6 ARM NEON optimisations
- NR_CPUS now defaults to 256 on arm64
- Minor clean-ups (documentation/comments, Kconfig warning, unused
asm-offsets, clang warnings)
- MAINTAINERS update for list information to the ARM64 ACPI entry
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (54 commits)
arm64: mmu: drop paging_init comments
arm64: debug: Ensure debug handlers check triggering exception level
arm64: debug: Don't propagate UNKNOWN FAR into si_code for debug signals
Revert "arm64: uaccess: Implement unsafe accessors"
arm64: avoid clang warning about self-assignment
arm64: Kconfig.platforms: fix warning unmet direct dependencies
lib/raid6: arm: optimize away a mask operation in NEON recovery routine
lib/raid6: use vdupq_n_u8 to avoid endianness warnings
arm64: io: Hook up __io_par() for inX() ordering
riscv: io: Update __io_[p]ar() macros to take an argument
asm-generic/io: Pass result of I/O accessor to __io_[p]ar()
arm64: Add workaround for Fujitsu A64FX erratum 010001
arm64: Rename get_thread_info()
arm64: Remove documentation about TIF_USEDFPU
arm64: irqflags: Fix clang build warnings
arm64: Enable the support of pseudo-NMIs
arm64: Skip irqflags tracing for NMI in IRQs disabled context
arm64: Skip preemption when exiting an NMI
arm64: Handle serror in NMI context
irqchip/gic-v3: Allow interrupts to be set as pseudo-NMI
...
|
|
Pull ARM SoC late updates from Arnd Bergmann:
"Here are two branches that came relatively late during the linux-5.0
development cycle and have dependencies on the other branches:
- On the TI OMAP platform, the CPSW Ethernet PHY mode selection
driver is being replaced, this puts the final pieces in place
- On the DaVinci platform, the interrupt handling code in arch/arm
gets moved into a regular device driver in drivers/irqchip.
Since they both had some time in linux-next after the 5.0-rc8 release,
I'm sending them along with the other updates"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
net: ethernet: ti: cpsw: deprecate cpsw-phy-sel driver
ARM: davinci: remove intc related fields from davinci_soc_info
irqchip: davinci-cp-intc: move the driver to drivers/irqchip
ARM: davinci: cp-intc: remove redundant comments
ARM: davinci: cp-intc: drop GPL license boilerplate
ARM: davinci: cp-intc: use readl/writel_relaxed()
ARM: davinci: cp-intc: unify error handling
ARM: davinci: cp-intc: improve coding style
ARM: davinci: cp-intc: request the memory region before remapping it
ARM: davinci: cp-intc: use the new-style config structure
ARM: davinci: cp-intc: convert all hex numbers to lowercase
ARM: davinci: cp-intc: use a common prefix for all symbols
ARM: davinci: cp-intc: add the new config structures for da8xx SoCs
irqchip: davinci-cp-intc: add a new config structure
ARM: davinci: cp-intc: add a wrapper around cp_intc_init()
ARM: davinci: cp-intc: remove cp_intc.h
irqchip: davinci-aintc: move the driver to drivers/irqchip
ARM: davinci: aintc: remove unnecessary includes
ARM: davinci: aintc: remove the timer-specific irq_set_handler()
ARM: davinci: aintc: request memory region before remapping it
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The interrupt departement delivers this time:
- New infrastructure to manage NMIs on platforms which have a sane
NMI delivery, i.e. identifiable NMI vectors instead of a single
lump.
- Simplification of the interrupt affinity management so drivers
don't have to implement ugly loops around the PCI/MSI enablement.
- Speedup for interrupt statistics in /proc/stat
- Provide a function to retrieve the default irq domain
- A new interrupt controller for the Loongson LS1X platform
- Affinity support for the SiFive PLIC
- Better support for the iMX irqsteer driver
- NUMA aware memory allocations for GICv3
- The usual small fixes, improvements and cleanups all over the
place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
irqchip/imx-irqsteer: Add multi output interrupts support
irqchip/imx-irqsteer: Change to use reg_num instead of irq_group
dt-bindings: irq: imx-irqsteer: Add multi output interrupts support
dt-binding: irq: imx-irqsteer: Use irq number instead of group number
irqchip/brcmstb-l2: Use _irqsave locking variants in non-interrupt code
irqchip/gicv3-its: Use NUMA aware memory allocation for ITS tables
irqdomain: Allow the default irq domain to be retrieved
irqchip/sifive-plic: Implement irq_set_affinity() for SMP host
irqchip/sifive-plic: Differentiate between PLIC handler and context
irqchip/sifive-plic: Add warning in plic_init() if handler already present
irqchip/sifive-plic: Pre-compute context hart base and enable base
PCI/MSI: Remove obsolete sanity checks for multiple interrupt sets
genirq/affinity: Remove the leftovers of the original set support
nvme-pci: Simplify interrupt allocation
genirq/affinity: Add new callback for (re)calculating interrupt sets
genirq/affinity: Store interrupt sets size in struct irq_affinity
genirq/affinity: Code consolidation
irqchip/irq-sifive-plic: Check and continue in case of an invalid cpuid.
irqchip/i8259: Fix shutdown order by moving syscore_ops registration
dt-bindings: interrupt-controller: loongson ls1x intc
...
|
|
gcc points out that irqs_num is not initialized when of_property_read_u32()
is an empty stub function:
Included from drivers/irqchip/irq-imx-irqsteer.c:7:
drivers/irqchip/irq-imx-irqsteer.c: In function 'imx_irqsteer_probe':
include/uapi/linux/kernel.h:13:49: error: 'irqs_num' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The same can actually happen with CONFIG_OF=y as well, though we don't
get a warning then.
Add error checking here that lets the code deal with missing or
invalid properties as well as avoid the warning.
Fixes: 28528fca4908 ("irqchip/imx-irqsteer: Add multi output interrupts support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier
- Core pseudo-NMI handling code
- Allow the default irq domain to be retrieved
- A new interrupt controller for the Loongson LS1X platform
- Affinity support for the SiFive PLIC
- Better support for the iMX irqsteer driver
- NUMA aware memory allocations for GICv3
- A handful of other fixes (i8259, GICv3, PLIC)
|
|
One irqsteer channel can support up to 8 output interrupts.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
One group can manage 64 interrupts by using two registers (e.g. STATUS/SET).
However, the integrated irqsteer may support only 32 interrupts which
needs only one register in a group. But the current driver assume there's
a mininum of two registers in a group which result in a wrong register map
for 32 interrupts per channel irqsteer. Let's use the reg_num caculated by
interrupts per channel instead of irq_group to cover this case.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Using the irq_gc_lock/irq_gc_unlock functions in the suspend and
resume functions creates the opportunity for a deadlock during
suspend, resume, and shutdown. Using the irq_gc_lock_irqsave/
irq_gc_unlock_irqrestore variants prevents this possible deadlock.
Cc: stable@vger.kernel.org
Fixes: 7f646e92766e2 ("irqchip: brcmstb-l2: Add Broadcom Set Top Box Level-2 interrupt controller")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
[maz: tidied up $SUBJECT]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The NUMA node information is visible to ITS driver but not being used
other than handling hardware errata. ITS/GICR hardware accesses to the
local NUMA node is usually quicker than the remote NUMA node. How slow
the remote NUMA accesses are depends on the implementation details.
This patch allocates memory for ITS management tables and command
queue from the corresponding NUMA node using the appropriate NUMA
aware functions. This change improves the performance of the ITS
tables read latency on systems where it has more than one ITS block,
and with the slower inter node accesses.
Apache Web server benchmarking using ab tool on a HiSilicon D06
board with multiple numa mem nodes shows Time per request and
Transfer rate improvements of ~3.6% with this patch.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Ganapatrao Kulkarni <gkulkarni@marvell.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Currently on SMP host, all CPUs take external interrupts routed via
PLIC. All CPUs will try to claim a given external interrupt but only
one of them will succeed while other CPUs would simply resume whatever
they were doing before. This means if we have N CPUs then for every
external interrupt N-1 CPUs will always fail to claim it and waste
their CPU time.
Instead of above, external interrupts should be taken by only one CPU
and we should have provision to explicitly specify IRQ affinity from
kernel-space or user-space.
This patch provides irq_set_affinity() implementation for PLIC driver.
It also updates irq_enable() such that PLIC interrupts are only enabled
for one of CPUs specified in IRQ affinity mask.
With this patch in-place, we can change IRQ affinity at any-time from
user-space using procfs.
Example:
/ # cat /proc/interrupts
CPU0 CPU1 CPU2 CPU3
8: 44 0 0 0 SiFive PLIC 8 virtio0
10: 48 0 0 0 SiFive PLIC 10 ttyS0
IPI0: 55 663 58 363 Rescheduling interrupts
IPI1: 0 1 3 16 Function call interrupts
/ #
/ #
/ # echo 4 > /proc/irq/10/smp_affinity
/ #
/ # cat /proc/interrupts
CPU0 CPU1 CPU2 CPU3
8: 45 0 0 0 SiFive PLIC 8 virtio0
10: 160 0 17 0 SiFive PLIC 10 ttyS0
IPI0: 68 693 77 410 Rescheduling interrupts
IPI1: 0 2 3 16 Function call interrupts
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
We explicitly differentiate between PLIC handler and context because
PLIC context is for given mode of HART whereas PLIC handler is per-CPU
software construct meant for handling interrupts from a particular
PLIC context.
To achieve this differentiation, we rename "nr_handlers" to "nr_contexts"
and "nr_mapped" to "nr_handlers" in plic_init().
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
We have two enteries (one for M-mode and another for S-mode) in the
interrupts-extended DT property of PLIC DT node for each HART. It is
expected that firmware/bootloader will set M-mode HWIRQ line of each
HART to 0xffffffff (i.e. -1) in interrupts-extended DT property
because Linux runs in S-mode only.
If firmware/bootloader is buggy then it will not correctly update
interrupts-extended DT property which might result in a plic_handler
configured twice. This patch adds a warning in plic_init() if a
plic_handler is already marked present. This warning provides us
a hint about incorrectly updated interrupts-extended DT property.
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
