| Age | Commit message (Collapse) | Author |
|---|
|
Currently the driver assumes that REG_BASE+0x00 is the IRQ enable mask,
and REG_BASE+0x04 is the IRQ status mask. This is true on BCM3384 and
BCM7xxx, but it is not true for some of the controllers found on BCM63xx
chips. So we will change a couple of key assumptions:
- Don't assume that both the IRQEN and IRQSTAT registers will be
covered by a single ioremap() operation.
- Don't assume any particular ordering (IRQSTAT might show up before
IRQEN on some chips).
- For an L2 controller with >=64 IRQs, don't assume that every
IRQEN/IRQSTAT pair will use the same register spacing.
This patch changes the "plumbing" but doesn't yet provide a way for users
to instantiate a controller with arbitrary IRQEN/IRQSTAT offsets.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8841/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Wakeable interrupts might be pending at boot/init time, because wakeup
interrupts might have triggered a resume from S5. So don't clear such
wakeups.
This means that any driver which requests a wakeable interrupt bit
should be prepared to handle an interrupt as soon as they call
request_irq(). (This is technically already the correct development
practice, but some drivers probably expect not to receive interrupts
until they have performed some I/O.)
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8840/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
We add new functions to start and stop the GIC counter since there are no
guarantees the counter will be running after a CPU reset. The GIC counter
is stopped by setting the 29th bit on the GIC Config register and it is
started by clearing that bit.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9594/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add a function to the MIPS GIC driver for retrieving the Fast Debug
Channel (FDC) interrupt number, similar to the existing ones for the
timer and perf counter interrupts. This will be used by platform
implementations of get_c0_fdc_int() if a GIC is present.
A workaround exists for interAptiv and proAptiv which claim to be able
to route the FDC interrupt but don't seem to be able to in practice (at
least on Malta).
[ralf@linux-mips.org: Fix conflict.]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9142/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Treat the Fast Debug Channel (FDC) interrupt the same as the timer and
performance counter interrupts. Like them, the FDC IRQ is also per-VPE,
and also doesn't use a per-CPU device ID yet. Per-CPU device IDs don't
seem to work with IRQF_SHARED which is needed for compatibility with
cores which don't route the FDC IRQ through the GIC. For hardware which
routes FDC IRQs through the GIC this is something that could be added
later.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9141/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Fix typo in comment in gic_get_c0_perfcount_int:
"erformance" -> "performance".
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Patchwork: https://patchwork.linux-mips.org/patch/9126/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
We add new functions to start and stop the GIC counter since there are no
guarantees the counter will be running after a CPU reset. The GIC counter
is stopped by setting the 29th bit on the GIC Config register and it is
started by clearing that bit.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: <linux-kernel@vger.kernel.org>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Link: https://lkml.kernel.org/r/1427113923-9840-2-git-send-email-markos.chandras@imgtec.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Tegra210 uses the same legacy interrupt controller as older generations
but it adds a sixth instance.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lkml.kernel.org/r/1427106379-14037-1-git-send-email-thierry.reding@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
|
|
If the ITS or the redistributors report their shareability as zero,
then it is important to make sure they will no generate any cacheable
traffic, as this is unlikely to produce the expected result.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1427465705-17126-5-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The ITS driver sometime mixes up the use of GICR_PROPBASE bitfields
for the GICR_PENDBASE register, and GITS_BASER for GICR_CBASE.
This does not lead to any observable bug because similar bits are
at the same location, but this just make the code even harder to
understand...
This patch provides the required #defines and fixes the mixup.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1427465705-17126-4-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
When building ITS commands which have the device ID in it, we
should mask off the whole upper 32 bits of the first command word
before inserting the new value in there.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1427465705-17126-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
With a monolithic GICv3, redistributors are addressed using a linear
number, while a distributed implementation uses physical addresses.
When encoding a target address into a command, we strip the lower
16 bits, as redistributors are always 64kB aligned. This works
perfectly well with a distributed implementation, but has the
silly effect of always encoding target 0 in the monolithic case
(unless you have more than 64k CPUs, of course).
The obvious fix is to shift the linear target number by 16 when
computing the target address, so that we don't loose any precious
bit.
Reported-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1427465705-17126-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The code deployed to implement GSI linux IRQ numbers mapping on arm64 turns
out to be generic enough so that it can be moved to ACPI core code along
with its respective config option ACPI_GENERIC_GSI selectable on
architectures that can reuse the same code.
Current ACPI IRQ mapping code is not integrated in the kernel IRQ domain
infrastructure, in particular there is no way to look-up the
IRQ domain associated with a particular interrupt controller, so this
first version of GSI generic code carries out the GSI<->IRQ mapping relying
on the IRQ default domain which is supposed to be always set on a
specific architecture in case the domain structure passed to
irq_create/find_mapping() functions is missing.
This patch moves the arm64 acpi functions that implement the gsi mappings:
acpi_gsi_to_irq()
acpi_register_gsi()
acpi_unregister_gsi()
to ACPI core code. Since the generic GSI<->domain mapping is based on IRQ
domains, it can be extended as soon as a way to map an interrupt
controller to an IRQ domain is implemented for ACPI in the IRQ domain
layer.
x86 and ia64 code for GSI mappings cannot rely on the generic GSI
layer at present for legacy reasons, so they do not select the
ACPI_GENERIC_GSI config options and keep relying on their arch
specific GSI mapping layer.
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
ACPI kernel uses MADT table for proper GIC initialization. It needs to
parse GIC related subtables, collect CPU interface and distributor
addresses and call driver initialization function (which is hardware
abstraction agnostic). In a similar way, FDT initialize GICv1/2.
NOTE: This commit allow to initialize GICv1/2 basic functionality.
While now simple GICv2 init call is used, any further GIC features
require generic infrastructure for proper ACPI irqchip initialization.
That mechanism and stacked irqdomains to support GICv2 MSI/virtualization
extension, GICv3/4 and its ITS are considered as next steps.
CC: Jason Cooper <jason@lakedaemon.net>
CC: Marc Zyngier <marc.zyngier@arm.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Yijing Wang <wangyijing@huawei.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
Tested-by: Timur Tabi <timur@codeaurora.org>
Tested-by: Robert Richter <rrichter@cavium.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The digicolor_set_gc() routine is only called from __init annotated
digicolor_of_init(). Annotate digicolor_set_gc() with __init as well to save a
few bytes at run time.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Link: https://lkml.kernel.org/r/a3b57ecdbe0b07f55c20c07ff98f1f694275722d.1427009985.git.baruch@tkos.co.il
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This is just enough to let pm_clk_*() enable the functional clock, and
manage it for suspend/resume, if present.
Before, it was assumed enabled by the bootloader or reset state.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lkml.kernel.org/r/1426704961-27322-3-git-send-email-geert+renesas@glider.be
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lkml.kernel.org/r/1426704961-27322-2-git-send-email-geert+renesas@glider.be
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
|
|
|
|
|
|
In a uniprocessor implementation the interrupt processor targets
registers are read-as-zero/write-ignored (RAZ/WI). Unfortunately
gic_get_cpumask() will print a critical message saying
GIC CPU mask not found - kernel will fail to boot.
if these registers all read as zero, but there won't actually be
a problem on uniprocessor systems and the kernel will boot just
fine. Skip this check if we're running a UP kernel or if we
detect that the hardware only supports a single processor.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Link: https://lkml.kernel.org/r/1426141291-21641-1-git-send-email-sboyd@codeaurora.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
A common use of gic_arch_extn is to set up additional flags
to the GIC irqchip. It looks like a benign enough hack that
doesn't really require the users of that feature to be converted
to stacked domains.
Add a gic_set_irqchip_flags() function that platform code can
call instead of using the dreaded gic_arch_extn.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088737-15817-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The only user of the so called "routable domain" functionality
now being fixed, let's clean up the GIC.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088629-15377-5-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Support for the TI crossbar used on the DRA7 family of chips
is implemented as an ugly hack on the side of the GIC.
Converting it to stacked domains makes it slightly more
palatable, as it results in a cleanup.
Unfortunately, as the DT bindings failed to acknowledge the
fact that this is actually yet another interrupt controller
(the third, actually), we have yet another breakage. Oh well.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088629-15377-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Tegra's LIC (Legacy Interrupt Controller) has been so far only
supported as a weird extension of the GIC, which is not exactly
pretty.
The stacked IRQ domain framework fits this pretty well, and allows
the LIC code to be turned into a standalone irqchip. In the process,
make the driver DT aware, something that was sorely missing from
the mach-tegra implementation.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088583-15097-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
It's unsafe to change the configurations of an activated ITS directly
since this will lead to unpredictable results. This patch guarantees
the ITSes being initialized are quiescent.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Yun Wu <wuyun.wu@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-12-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Define macros for GITS_CTLR fields to avoid using magic numbers.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Yun Wu <wuyun.wu@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-11-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
When required size of Device Table is out of the page allocator's
capability, the whole ITS will fail in probing. This actually is
not the hardware's problem and is mainly a limitation of the kernel
page allocator. This patch will keep ITS going on to the next
initializaion stage with an explicit warning.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Yun Wu <wuyun.wu@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-10-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The field of page size in register GITS_BASERn might be read-only
if an implementation only supports a single, fixed page size. But
currently the ITS driver will throw out an error when PAGE_SIZE
is less than the minimum size supported by an ITS. So addressing
this problem by using 64KB pages as default granule for all the
ITS base tables.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
[maz: fixed bug breaking non Device Table allocations]
Signed-off-by: Yun Wu <wuyun.wu@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-9-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Some kind of brain-dead implementations chooses to insert ITEes in
rapid sequence of disabled ITEes, and an un-zeroed ITT will confuse
ITS on judging whether an ITE is really enabled or not. Considering
the implementations are still supported by the GICv3 architecture,
in which ITT is not required to be zeroed before being handled to
hardware, we do the favor in ITS driver.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Yun Wu <wuyun.wu@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-8-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
While playing with KASan support for arm64/arm the following appeared on boot:
==================================================================
BUG: AddressSanitizer: out of bounds access in __asan_load8+0x14/0x1c at addr ffffffc000ad0dc0
Read of size 8 by task swapper/0/1
page:ffffffbdc202b400 count:1 mapcount:0 mapping: (null) index:0x0
flags: 0x400(reserved)
page dumped because: kasan: bad access detected
Address belongs to variable __cpu_logical_map+0x200/0x220
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 3.19.0-rc6-next-20150129+ #481
Hardware name: FVP Base (DT)
Call trace:
[<ffffffc00008a794>] dump_backtrace+0x0/0x184
[<ffffffc00008a928>] show_stack+0x10/0x1c
[<ffffffc00075e46c>] dump_stack+0xa0/0xf8
[<ffffffc0001df490>] kasan_report_error+0x23c/0x264
[<ffffffc0001e0188>] check_memory_region+0xc0/0xe4
[<ffffffc0001dedf0>] __asan_load8+0x10/0x1c
[<ffffffc000431294>] gic_raise_softirq+0xc4/0x1b4
[<ffffffc000091fc0>] smp_send_reschedule+0x30/0x3c
[<ffffffc0000f0d1c>] try_to_wake_up+0x394/0x434
[<ffffffc0000f0de8>] wake_up_process+0x2c/0x6c
[<ffffffc0000d9570>] wake_up_worker+0x38/0x48
[<ffffffc0000dbb50>] insert_work+0xac/0xec
[<ffffffc0000dbd38>] __queue_work+0x1a8/0x374
[<ffffffc0000dbf60>] queue_work_on+0x5c/0x7c
[<ffffffc0000d8a78>] call_usermodehelper_exec+0x170/0x188
[<ffffffc0004037b8>] kobject_uevent_env+0x650/0x6bc
[<ffffffc000403830>] kobject_uevent+0xc/0x18
[<ffffffc00040292c>] kset_register+0xa8/0xc8
[<ffffffc0004d6c88>] bus_register+0x134/0x2e8
[<ffffffc0004d73b4>] subsys_virtual_register+0x2c/0x5c
[<ffffffc000a76a4c>] wq_sysfs_init+0x14/0x20
[<ffffffc000082a28>] do_one_initcall+0xa8/0x1fc
[<ffffffc000a70db4>] kernel_init_freeable+0x1ec/0x294
[<ffffffc00075aa5c>] kernel_init+0xc/0xec
Memory state around the buggy address:
ffffff80003e0820: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffffff80003e0830: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffffff80003e0840: fa fa fa fa 00 00 00 00 00 00 00 00 00 00 00 00
^
ffffff80003e0850: 00 00 fa fa fa fa fa fa 00 00 00 00 00 00 00 00
==================================================================
The reason for that cpumask_next() returns >= nr_cpu_ids if no further cpus
set, but "==" condition is checked only, so we end up with out-of-bounds
access to cpu_logical_map.
Fix is by using the condition check for cpumask_next.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-7-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
When compiled with CONFIG_LOCKDEP, the kernel shouts badly, saying
that the locking in the GIC code is unsafe. I'm afraid the kernel
is right:
CPU0
----
lock(irq_controller_lock);
<Interrupt>
lock(irq_controller_lock);
*** DEADLOCK ***
This can happen while enabling, disabling, setting the type
or the affinity of an interrupt.
The fix is to take the interrupt_controller_lock with interrupts
disabled in these cases.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-6-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
When compiled with CONFIG_LOCKDEP, the kernel shouts badly, saying
that my locking is unsafe. I'm afraid the kernel is right:
CPU0 CPU1
---- ----
lock(&its->lock);
local_irq_disable();
lock(&irq_desc_lock_class);
lock(&its->lock);
<Interrupt>
lock(&irq_desc_lock_class);
*** DEADLOCK ***
The fix is to always take its->lock with interrupts disabled.
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-5-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The current PCI/MSI support in the GICv3 ITS doesn't really deal
with systems where different PCI devices end-up using the same
RequesterID (as it would be the case with non-transparent bridges,
for example). It is likely that none of these devices would
actually generate any interrupt, as the ITS is programmed with
the device's own ID, and not that of the bridge.
A solution to this is to iterate over the PCI hierarchy to
discover what the device aliases too. We also use this
to discover the upper bound of the number of MSIs that this
sub-hierarchy can generate.
With this in place, PCI aliases can be supported.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-4-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The ITS table allocator is only allocating a single page per table.
This works fine for most things, but leads to silent lack of
interrupt delivery if we end-up with a device that has an ID that is
out of the range defined by a single page of memory. Even worse, depending
on the page size, behaviour changes, which is not a very good experience.
A solution is actually to allocate memory for the full range of ID that
the ITS supports. A massive waste memory wise, but at least a safe bet.
Tested on a Phytium SoC.
Tested-by: Chen Baozi <chenbaozi@kylinos.com.cn>
Acked-by: Chen Baozi <chenbaozi@kylinos.com.cn>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
We skip initialisation of ITS in case the device-tree has no
corresponding description, but we are still accessing to ITS bits while
setting CPU interface what leads to the kernel panic:
ITS: No ITS available, not enabling LPIs
CPU0: found redistributor 0 region 0:0x000000002f100000
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = ffffffc0007fb000
[00000000] *pgd=00000000fc407003, *pud=00000000fc407003, *pmd=00000000fc408003, *pte=006000002f000707
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.19.0-rc2+ #318
Hardware name: FVP Base (DT)
task: ffffffc00077edb0 ti: ffffffc00076c000 task.ti: ffffffc00076c000
PC is at its_cpu_init+0x2c/0x320
LR is at gic_cpu_init+0x168/0x1bc
It happens in gic_rdists_supports_plpis() because gic_rdists is NULL.
The gic_rdists is set to non-NULL only when ITS node is presented in
the device-tree.
Fix this by moving the call to gic_rdists_supports_plpis() inside the
!list_empty(&its_nodes) block, because it is that list that guards the
validity of the rest of the information in this driver.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
In order to let the Performance Monitoring Unit interrupts flowing in the MPIC,
we need to unmask these interrupts in the Coherency Fabric Local Interrupt Mask
Register.
Since this register is a CPU-local register, unmasking this interrupt needs to
be done on the boot CPU when the driver initializes, but also on the secondary
CPU when they are brought up.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1425379400-4346-4-git-send-email-maxime.ripard@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This commit introduces a helper function is_percpu_irq(), to be used
when interrupts are mapped to decide which ones are set as per CPU.
This change will allow to extend the list of per cpu interrupts in a less
intrusive fashion; also, it makes the code slightly more readable by keeping
a list of the per CPU interrupts.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1425379400-4346-3-git-send-email-maxime.ripard@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The irqchip driver called armada_xp_mpic_smp_cpu_init() when CONFIG_SMP=Y
to initialize some per cpu registers. The function is called on each
CPU by calling it explicitly on the boot CPU and then using a CPU notifier
for the non boot CPUs.
This commit removes the CONFIG_SMP constrain, so the per cpu registers are
also initialized when CONFIG_SMP=N, which is the right thing to do.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1425379400-4346-2-git-send-email-maxime.ripard@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This adds support for Vybrid's interrupt router. On VF6xx models,
almost all peripherals can be used by either of the two CPU's,
the Cortex-A5 or the Cortex-M4. The interrupt router routes the
peripheral interrupts to the configured CPU.
This IRQ chip driver configures the interrupt router to route
the requested interrupt to the CPU the kernel is running on.
The driver makes use of the irqdomain hierarchy support. The
parent is given by the device tree. This should be one of the
two possible parents either ARM GIC or the ARM NVIC interrupt
controller. The latter is currently not yet supported.
Note that there is no resource control mechnism implemented to
avoid concurrent access of the same peripheral. The user needs
to make sure to use device trees which assign the peripherals
orthogonally. However, this driver warns the user in case the
interrupt is already configured for the other CPU. This provides
a poor man's resource controller.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://lkml.kernel.org/r/1425249689-32354-2-git-send-email-stefan@agner.ch
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
On the Cortex-A9-based Armada SoCs, the MPIC is not the primary interrupt
controller. Yet, it still has to handle some per-cpu interrupt.
To do so, it is chained with the GIC using a per-cpu interrupt. However, the
current code only call irq_set_chained_handler, which is called and enable that
interrupt only on the boot CPU, which means that the parent per-CPU interrupt
is never unmasked on the secondary CPUs, preventing the per-CPU interrupt to
actually work as expected.
This was not seen until now since the only MPIC PPI users were the Marvell
timers that were not working, but not used either since the system use the ARM
TWD by default, and the ethernet controllers, that are faking there interrupts
as SPI, and don't really expect to have interrupts on the secondary cores
anyway.
Add a CPU notifier that will enable the PPI on the secondary cores when they
are brought up.
Cc: <stable@vger.kernel.org> # 3.15+
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1425378443-28822-1-git-send-email-maxime.ripard@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
|
|
Thanks to spatch, plus manual removal of "&*". Then a sweep for
for_each_cpu_mask => for_each_cpu.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: netdev@vger.kernel.org
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lkml.kernel.org/r/1424947412-8061-1-git-send-email-geert+renesas@glider.be
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This driver is used to enable System Configuration Register controlled
External, CTI (Core Sight), PMU (Performance Management), and PL310 L2
Cache IRQs prior to use.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lkml.kernel.org/r/1424272444-16230-3-git-send-email-lee.jones@linaro.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS:
- a number of fixes that didn't make the 3.19 release.
- a number of cleanups.
- preliminary support for Cavium's Octeon 3 SOCs which feature up to
48 MIPS64 R3 cores with FPU and hardware virtualization.
- support for MIPS R6 processors.
Revision 6 of the MIPS architecture is a major revision of the MIPS
architecture which does away with many of original sins of the
architecture such as branch delay slots. This and other changes in
R6 require major changes throughout the entire MIPS core
architecture code and make up for the lion share of this pull
request.
- finally some preparatory work for eXtendend Physical Address
support, which allows support of up to 40 bit of physical address
space on 32 bit processors"
[ Ahh, MIPS can't leave the PAE brain damage alone. It's like
every CPU architect has to make that mistake, but pee in the snow
by changing the TLA. But whether it's called PAE, LPAE or XPA,
it's horrid crud - Linus ]
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (114 commits)
MIPS: sead3: Corrected get_c0_perfcount_int
MIPS: mm: Remove dead macro definitions
MIPS: OCTEON: irq: add CIB and other fixes
MIPS: OCTEON: Don't do acknowledge operations for level triggered irqs.
MIPS: OCTEON: More OCTEONIII support
MIPS: OCTEON: Remove setting of processor specific CVMCTL icache bits.
MIPS: OCTEON: Core-15169 Workaround and general CVMSEG cleanup.
MIPS: OCTEON: Update octeon-model.h code for new SoCs.
MIPS: OCTEON: Implement DCache errata workaround for all CN6XXX
MIPS: OCTEON: Add little-endian support to asm/octeon/octeon.h
MIPS: OCTEON: Implement the core-16057 workaround
MIPS: OCTEON: Delete unused COP2 saving code
MIPS: OCTEON: Use correct instruction to read 64-bit COP0 register
MIPS: OCTEON: Save and restore CP2 SHA3 state
MIPS: OCTEON: Fix FP context save.
MIPS: OCTEON: Save/Restore wider multiply registers in OCTEON III CPUs
MIPS: boot: Provide more uImage options
MIPS: Remove unneeded #ifdef __KERNEL__ from asm/processor.h
MIPS: ip22-gio: Remove legacy suspend/resume support
mips: pci: Add ifdef around pci_proc_domain
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irqchip updates from Ingo Molnar:
"Various irqchip driver updates, plus a genirq core update that allows
the initial spreading of irqs amonst CPUs without having to do it from
user-space"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Fix null pointer reference in irq_set_affinity_hint()
irqchip: gic: Allow interrupt level to be set for PPIs
irqchip: mips-gic: Handle pending interrupts once in __gic_irq_dispatch()
irqchip: Conexant CX92755 interrupts controller driver
irqchip: Devicetree: document Conexant Digicolor irq binding
irqchip: omap-intc: Remove unused legacy interface for omap2
irqchip: omap-intc: Fix support for dm814 and dm816
irqchip: mtk-sysirq: Get irq number from register resource size
irqchip: renesas-intc-irqpin: r8a7779 IRLM setup support
genirq: Set initial affinity in irq_set_affinity_hint()
|
|
Pull KVM update from Paolo Bonzini:
"Fairly small update, but there are some interesting new features.
Common:
Optional support for adding a small amount of polling on each HLT
instruction executed in the guest (or equivalent for other
architectures). This can improve latency up to 50% on some
scenarios (e.g. O_DSYNC writes or TCP_RR netperf tests). This
also has to be enabled manually for now, but the plan is to
auto-tune this in the future.
ARM/ARM64:
The highlights are support for GICv3 emulation and dirty page
tracking
s390:
Several optimizations and bugfixes. Also a first: a feature
exposed by KVM (UUID and long guest name in /proc/sysinfo) before
it is available in IBM's hypervisor! :)
MIPS:
Bugfixes.
x86:
Support for PML (page modification logging, a new feature in
Broadwell Xeons that speeds up dirty page tracking), nested
virtualization improvements (nested APICv---a nice optimization),
usual round of emulation fixes.
There is also a new option to reduce latency of the TSC deadline
timer in the guest; this needs to be tuned manually.
Some commits are common between this pull and Catalin's; I see you
have already included his tree.
Powerpc:
Nothing yet.
The KVM/PPC changes will come in through the PPC maintainers,
because I haven't received them yet and I might end up being
offline for some part of next week"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (130 commits)
KVM: ia64: drop kvm.h from installed user headers
KVM: x86: fix build with !CONFIG_SMP
KVM: x86: emulate: correct page fault error code for NoWrite instructions
KVM: Disable compat ioctl for s390
KVM: s390: add cpu model support
KVM: s390: use facilities and cpu_id per KVM
KVM: s390/CPACF: Choose crypto control block format
s390/kernel: Update /proc/sysinfo file with Extended Name and UUID
KVM: s390: reenable LPP facility
KVM: s390: floating irqs: fix user triggerable endless loop
kvm: add halt_poll_ns module parameter
kvm: remove KVM_MMIO_SIZE
KVM: MIPS: Don't leak FPU/DSP to guest
KVM: MIPS: Disable HTW while in guest
KVM: nVMX: Enable nested posted interrupt processing
KVM: nVMX: Enable nested virtual interrupt delivery
KVM: nVMX: Enable nested apic register virtualization
KVM: nVMX: Make nested control MSRs per-cpu
KVM: nVMX: Enable nested virtualize x2apic mode
KVM: nVMX: Prepare for using hardware MSR bitmap
...
|
|
Pull MIPS fixes from Ralf Baechle:
"The pending MIPS fixes for 3.19. All across the field and nothing
particularly severe or dramatic"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (23 commits)
IRQCHIP: mips-gic: Avoid rerouting timer IRQs for smp-cmp
MIPS: Fix syscall_get_nr for the syscall exit tracing.
MIPS: elf2ecoff: Ignore PT_MIPS_ABIFLAGS program headers.
MIPS: elf2ecoff: Rewrite main processing loop to switch.
MIPS: fork: Fix MSA/FPU/DSP context duplication race
MIPS: Fix C0_Pagegrain[IEC] support.
MIPS: traps: Fix inline asm ctc1 missing .set hardfloat
MIPS: mipsregs.h: Add write_32bit_cp1_register()
MIPS: Fix kernel lockup or crash after CPU offline/online
MIPS: OCTEON: fix kernel crash when offlining a CPU
MIPS: ARC: Fix build error.
MIPS: IRQ: Fix disable_irq on CPU IRQs
MIPS: smp-mt,smp-cmp: Enable all HW IRQs on secondary CPUs
MIPS: Fix restart of indirect syscalls
MIPS: ELF: fix loading o32 binaries on 64-bit kernels
MIPS: mips-cm: Fix sparse warnings
MIPS: Kconfig: Fix recursive dependency.
MIPS: Compat: Fix build error if CONFIG_MIPS32_COMPAT but no compat ABI.
MIPS: JZ4740: Fixup #include's (sparse)
MIPS: Wire up execveat(2).
...
|
