| Age | Commit message (Collapse) | Author |
|---|
|
When processors are about to hit low power states, the assertion of
standbywfi signal, triggered by the wfi instruction, is essential to
entering low power modes. If an IRQ is pending on the processor at the
time wfi is issued, the wfi instruction completes and the processor
restarts execution without asserting the standbywfi signal. Depending
on the platform power controller HW this behaviour can be acceptable or
not; if this behaviour must be prevented software should be provided
with a way to disable the routing of interrupts to the core IRQ pins.
On systems where raw GIC distributor interrupts are connected to the power
controller as wake-up events (hence the power controller still senses
IRQs and can wake up cores upon IRQ pending), the GIC CPU interface can
be disabled on power down, so that the GIC CPU IF output is gated and wfi
cannot complete, thereby preventing the standbywfi issue.
This patch adds a simple function to the GIC driver that allows to
disable the GIC CPU IF from power down procedures.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[rewrote commit log]
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Currently, GIC IDs are hardcoded making the code dependent on the 4+4 b.L
configuration. Let's allow for GIC IDs to be discovered upon switcher
initialization to support other b.L configurations such as the 1+1 one,
or 2+3 as on the VExpress TC2.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
|
|
This is required by the big.LITTLE switcher code.
The gic_migrate_target() changes the CPU interface mapping for the
current CPU to redirect SGIs to the specified interface, and it also
updates the target CPU for each interrupts to that CPU interface
if they were targeting the current interface. Finally, pending
SGIs for the current CPU are forwarded to the new interface.
Because Linux does not use it, the SGI source information for the
forwarded SGIs is not preserved. Neither is the source information
for the SGIs sent by the current CPU to other CPUs adjusted to match
the new CPU interface mapping. The required registers are banked so
only the target CPU could do it.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
|
|
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
This removes all the drivers/clocksource and drivers/irqchip uses of
the __cpuinit macros from all C files.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Commit c011470 (irqchip: gic: Perform the gic_secondary_init() call via
CPU notifier) moves gic_secondary_init() that used to be called in
.smp_secondary_init hook into a notifier call. But it changes the
system behavior a little bit. Before the commit, gic_cpu_init()
is called not only when kernel brings up the secondary cores but also
when system resuming procedure hot-plugs the cores back to kernel.
While after the commit, the function will not be called in the latter
case, where the 'action' will not be CPU_STARTING but
CPU_STARTING_FROZEN. This behavior difference at least causes the
following suspend/resume regression on imx6q.
$ echo mem > /sys/power/state
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
mmc1: card e624 removed
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
PM: Entering mem sleep
PM: suspend of devices complete after 5.930 msecs
PM: suspend devices took 0.010 seconds
PM: late suspend of devices complete after 0.343 msecs
PM: noirq suspend of devices complete after 0.828 msecs
Disabling non-boot CPUs ...
CPU1: shutdown
CPU2: shutdown
CPU3: shutdown
Enabling non-boot CPUs ...
CPU1: Booted secondary processor
INFO: rcu_sched detected stalls on CPUs/tasks: { 1 2 3} (detected by 0, t=2102 jiffies, g=4294967169, c=4294967168, q=17)
Task dump for CPU 1:
swapper/1 R running 0 0 1 0x00000000
Backtrace:
[<bf895ff4>] (0xbf895ff4) from [<00000000>] ( (null))
Backtrace aborted due to bad frame pointer <8007ccdc>
Task dump for CPU 2:
swapper/2 R running 0 0 1 0x00000000
Backtrace:
[<8075dbdc>] (0x8075dbdc) from [<00000000>] ( (null))
Backtrace aborted due to bad frame pointer <00000002>
Task dump for CPU 3:
swapper/3 R running 0 0 1 0x00000000
Backtrace:
[<8075dbdc>] (0x8075dbdc) from [<00000000>] ( (null))
Fix the regression by checking 'action' being CPU_STARTING_FROZEN to
have gic_cpu_init() called for secondary cores when system resumes.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanup from Olof Johansson:
"Here is a collection of cleanup patches. Among the pieces that stand
out are:
- The deletion of h720x platforms
- Split of at91 non-dt platforms to their own Kconfig file to keep
them separate
- General cleanups and refactoring of i.MX and MXS platforms
- Some restructuring of clock tables for OMAP
- Convertion of PMC driver for Tegra to dt-only
- Some renames of sunxi -> sun4i (Allwinner A10)
- ... plus a bunch of other stuff that I haven't mentioned"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (119 commits)
ARM: i.MX: remove unused ARCH_* configs
ARM i.MX53: remove platform ahci support
ARM: sunxi: Rework the restart code
irqchip: sunxi: Rename sunxi to sun4i
irqchip: sunxi: Make use of the IRQCHIP_DECLARE macro
clocksource: sunxi: Rename sunxi to sun4i
clocksource: sunxi: make use of CLKSRC_OF
clocksource: sunxi: Cleanup the timer code
ARM: at91: remove trailing semicolon from macros
ARM: at91/setup: fix trivial typos
ARM: EXYNOS: remove "config EXYNOS_DEV_DRM"
ARM: EXYNOS: change the name of USB ohci header
ARM: SAMSUNG: Remove unnecessary code for dma
ARM: S3C24XX: Remove unused GPIO drive strength register definitions
ARM: OMAP4+: PM: Restore CPU power state to ON with clockdomain force wakeup method
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2412
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2410
ARM: S3C24XX: Removed unneeded dependency on ARCH_S3C24XX for boards
ARM: SAMSUNG: Fix typo "CONFIG_SAMSUNG_DEV_RTC"
ARM: S5P64X0: Fix typo "CONFIG_S5P64X0_SETUP_SDHCI"
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64 into next/cleanup
* 'gic' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
irqchip: gic: Perform the gic_secondary_init() call via CPU notifier
irqchip: gic: Call handle_bad_irq() directly
arm: Move chained_irq_(enter|exit) to a generic file
arm: Move the set_handle_irq and handle_arch_irq declarations to asm/irq.h
+ Linux 3.9-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Fixes the following errors:
ERROR: do not initialise statics to 0 or NULL
ERROR: space required after that ',' (ctx:VxV)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The genirq layer expects a 0 in case that the retrigger function is
not able to resend the irq in hardware, but the code is returning
-ENXIO. Fix it.
[ tglx: Reworked comment and changelog ]
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1363734349-32635-1-git-send-email-sboyd@codeaurora.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
All the calls to gic_secondary_init() pass 0 as the first argument.
Since this function is called on each CPU when starting, it can be done
in a platform-independent way via a CPU notifier registered by the GIC
code.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Tested-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Barry Song <baohua.song@csr.com>
|
|
Previously, the gic_handle_cascade_irq() function was calling the
ARM-specific do_bad_IRQ() function which calls handle_bad_irq() after
acquiring the desk->lock. Locking the cascaded IRQ desc is not needed
for error reporting, so just call handle_bad_irq() directly.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
|
|
These functions have been introduced by commit 10a8c383 (irq: introduce
entry and exit functions for chained handlers) in asm/mach/irq.h. This
patch moves them to linux/irqchip/chained_irq.h so that generic irqchip
drivers do not rely on architecture specific header files.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
|
|
In b1cffebf (ARM: GIC: remove direct use of gic_raise_softirq)
gic_raise_softirq() was moved inside arch/arm/common/gic.c but in the
process it reverted by mistake a change to that function made by
384a290 (ARM: gic: use a private mapping for CPU target interfaces).
This breaks multicluster systems on ARM.
This patch fixes the typo.
Signed-off-by: Javi Merino <javi.merino@arm.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pull ARM SoC cleanups from Arnd Bergmann:
"A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even
specify the driver they use, it can all get configured from the device
tree as we do for normal device drivers. The clocksource changes
basically touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose their
headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code."
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
ARM: mvebu: correct gated clock documentation
ARM: kirkwood: add missing include for nsa310
ARM: exynos: move exynos4210-combiner to drivers/irqchip
mfd: db8500-prcmu: update resource passing
drivers/db8500-cpufreq: delete dangling include
ARM: at91: remove NEOCORE 926 board
sunxi: Cleanup the reset code and add meaningful registers defines
ARM: S3C24XX: header mach/regs-mem.h local
ARM: S3C24XX: header mach/regs-power.h local
ARM: S3C24XX: header mach/regs-s3c2412-mem.h local
ARM: S3C24XX: Remove plat-s3c24xx directory in arch/arm/
ARM: S3C24XX: transform s3c2443 subirqs into new structure
ARM: S3C24XX: modify s3c2443 irq init to initialize all irqs
ARM: S3C24XX: move s3c2443 irq code to irq.c
ARM: S3C24XX: transform s3c2416 irqs into new structure
ARM: S3C24XX: modify s3c2416 irq init to initialize all irqs
ARM: S3C24XX: move s3c2416 irq init to common irq code
ARM: S3C24XX: Modify s3c_irq_wake to use the hwirq property
ARM: S3C24XX: Move irq syscore-ops to irq-pm
clocksource: always define CLOCKSOURCE_OF_DECLARE
...
|
|
Now that we have GIC moved to drivers/irqchip and all GIC DT init for
platforms using irqchip_init, move gic.h and update the remaining
includes.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
|
|
Now that we have drivers/irqchip, move GIC irqchip to drivers/irqchip. This
is necessary to share the GIC with arm and arm64.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
|
