| Age | Commit message (Collapse) | Author |
|---|
|
In MediaTek's IOMMU design, When a iommu translation fault occurs
(HW can NOT translate the destination address to a valid physical
address), the IOMMU HW output the dirty data into a special memory
to avoid corrupting the main memory, this is called "protect memory".
the register(0x114) for protect memory is a little different between
mt8173 and mt2712.
In the mt8173, bit[30:6] in the register represents [31:7] of the
physical address. In the 4GB mode, the register bit[31] should be 1.
While in the mt2712, the bits don't shift. bit[31:7] in the register
represents [31:7] in the physical address, and bit[1:0] in the
register represents bit[33:32] of the physical address if it has.
Fixes: e6dec9230862 ("iommu/mediatek: Add mt2712 IOMMU support")
Reported-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
'x86/vt-d' and 'core' into next
|
|
Now that the core API issues its own post-unmap TLB sync call, push that
operation out from the io-pgtable-arm-v7s internals into the users. For
now, we leave the invalidation implicit in the unmap operation, since
none of the current users would benefit much from any change to that.
Note that the conversion of msm_iommu is implicit, since that apparently
has no specific TLB sync operation anyway.
CC: Yong Wu <yong.wu@mediatek.com>
CC: Rob Clark <robdclark@gmail.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The ARM short descriptor has already limited the physical address
to 32bit after the commit <76557391433c> ("iommu/io-pgtable: Sanitise
map/unmap addresses"). But in MediaTek 4GB mode, the physical address
is from 0x1_0000_0000 to 0x1_ffff_ffff. this will cause:
WARNING: CPU: 4 PID: 3900 at
xxx/drivers/iommu/io-pgtable-arm-v7s.c:482 arm_v7s_map+0x40/0xf8
Modules linked in:
CPU: 4 PID: 3900 Comm: weston Tainted: G S W 4.9.44 #1
Hardware name: MediaTek MT2712m1v1 board (DT)
task: ffffffc0eaa5b280 task.stack: ffffffc0e9858000
PC is at arm_v7s_map+0x40/0xf8
LR is at mtk_iommu_map+0x64/0x90
pc : [<ffffff80085b09e8>] lr : [<ffffff80085b29fc>] pstate: 000001c5
sp : ffffffc0e985b920
x29: ffffffc0e985b920 x28: 0000000127d00000
x27: 0000000000100000 x26: ffffff8008f9e000
x25: 0000000000000003 x24: 0000000000100000
x23: 0000000127d00000 x22: 00000000ff800000
x21: ffffffc0f7ec8ce0 x20: 0000000000000003
x19: 0000000000000003 x18: 0000000000000002
x17: 0000007f7e5d72c0 x16: ffffff80082b0f08
x15: 0000000000000001 x14: 000000000000003f
x13: 0000000000000000 x12: 0000000000000028
x11: 0088000000000000 x10: 0000000000000000
x9 : ffffff80092fa000 x8 : ffffffc0e9858000
x7 : ffffff80085b29d8 x6 : 0000000000000000
x5 : ffffff80085b09a8 x4 : 0000000000000003
x3 : 0000000000100000 x2 : 0000000127d00000
x1 : 00000000ff800000 x0 : 0000000000000001
...
Call trace:
[<ffffff80085b09e8>] arm_v7s_map+0x40/0xf8
[<ffffff80085b29fc>] mtk_iommu_map+0x64/0x90
[<ffffff80085ab5f8>] iommu_map+0x100/0x3a0
[<ffffff80085ab99c>] default_iommu_map_sg+0x104/0x168
[<ffffff80085aead8>] iommu_dma_alloc+0x238/0x3f8
[<ffffff8008098b30>] __iommu_alloc_attrs+0xa8/0x260
[<ffffff80085f364c>] mtk_drm_gem_create+0xac/0x180
[<ffffff80085f3894>] mtk_drm_gem_dumb_create+0x54/0xc8
[<ffffff80085d576c>] drm_mode_create_dumb_ioctl+0xa4/0xd8
[<ffffff80085cb2a0>] drm_ioctl+0x1c0/0x490
In order to satify this, Limit the physical address to 32bit.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The commit ("iommu/mediatek: Enlarge the validate PA range
for 4GB mode") introduce the following build warning while ARCH=arm:
drivers/iommu/mtk_iommu.c: In function 'mtk_iommu_iova_to_phys':
include/linux/bitops.h:6:24: warning: left shift count >= width
of type [-Wshift-count-overflow]
#define BIT(nr) (1UL << (nr))
^
>> drivers/iommu/mtk_iommu.c:407:9: note: in expansion of macro 'BIT'
pa |= BIT(32);
drivers/iommu/mtk_iommu.c: In function 'mtk_iommu_probe':
include/linux/bitops.h:6:24: warning: left shift count >= width
of type [-Wshift-count-overflow]
#define BIT(nr) (1UL << (nr))
^
drivers/iommu/mtk_iommu.c:589:35: note: in expansion of macro 'BIT'
data->enable_4GB = !!(max_pfn > (BIT(32) >> PAGE_SHIFT));
Use BIT_ULL instead of BIT.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The commit ("iommu/mediatek: Enlarge the validate PA range
for 4GB mode") introduce the following build error:
drivers/iommu/mtk_iommu.c: In function 'mtk_iommu_hw_init':
>> drivers/iommu/mtk_iommu.c:536:30: error: 'const struct mtk_iommu_data'
has no member named 'm4u_type'; did you mean 'm4u_dom'?
if (data->enable_4GB && data->m4u_type != M4U_MT8173) {
This patch fix it, use "m4u_plat" instead of "m4u_type".
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This patch is for 4GB mode, mainly for 4 issues:
1) Fix a 4GB bug:
if the dram base is 0x4000_0000, the dram size is 0xc000_0000.
then the code just meet a corner case because max_pfn is
0x10_0000.
data->enable_4GB = !!(max_pfn > (0xffffffffUL >> PAGE_SHIFT));
It's true at the case above. That is unexpected.
2) In mt2712, there is a new register for the 4GB PA range(0x118)
we should enlarge the max PA range, or the HW will report
error.
The dram range is from 0x1_0000_0000 to 0x1_ffff_ffff in the 4GB
mode, we cut out the bit[32:30] of the SA(Start address) and
EA(End address) into this REG_MMU_VLD_PA_RNG(0x118).
3) In mt2712, the register(0x13c) is extended for 4GB mode.
bit[7:6] indicate the valid PA[32:33]. Thus, we don't mask the
value and print it directly for debug.
4) if 4GB is enabled, the dram PA range is from 0x1_0000_0000 to
0x1_ffff_ffff. Thus, the PA from iova_to_pa should also '|' BIT(32)
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
When system suspend, infra power domain may be off, and the iommu's
clock must be disabled when system off, or the iommu's bclk clock maybe
disabled after system resume.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
After adding the global list for M4U HW, We get a chance to
move the pagetable allocation into the mtk_iommu_domain_alloc.
Let the domain_alloc do the right thing.
This patch is for fixing this problem[1].
[1]: https://patchwork.codeaurora.org/patch/53987/
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
In theory, If there are 2 M4U HWs, there should be 2 IOMMU domains.
But one IOMMU domain(4GB iova range) is enough for us currently,
It's unnecessary to maintain 2 pagetables.
Besides, This patch can simplify our consumer code largely. They don't
need map a iova range from one domain into another, They can share the
iova address easily.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The M4U IP blocks in mt2712 is MTK's generation2 M4U which use the
ARM Short-descriptor like mt8173, and most of the HW registers are
the same.
The difference is that there are 2 M4U HWs in mt2712 while there's
only one in mt8173. The purpose of 2 M4U HWs is for balance the
bandwidth.
Normally if there are 2 M4U HWs, there should be 2 iommu domains,
each M4U has a iommu domain.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The definition of MTK_M4U_TO_LARB and MTK_M4U_TO_PORT are shared by
all the gen2 M4U HWs. Thus, Move them out from mt8173-larb-port.h,
and put them into the c file.
Suggested-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Under certain circumstances, the io-pgtable code may end up issuing two
TLB sync operations without any intervening invalidations. This goes
badly for the M4U hardware, since it means the second sync ends up
polling for a non-existent operation to finish, and as a result times
out and warns. The io_pgtable_tlb_* helpers implement a high-level
optimisation to avoid issuing the second sync at all in such cases, but
in order to work correctly that requires all pagetable operations to be
serialised under a lock, thus is no longer applicable to all io-pgtable
users.
Since we're the only user actually relying on this flag for correctness,
let's reimplement it locally to avoid the headache of trying to make the
high-level version concurrency-safe for other users.
CC: Yong Wu <yong.wu@mediatek.com>
CC: Matthias Brugger <matthias.bgg@gmail.com>
Tested-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
And also move its remaining functionality to
iommu_device_register() and 'struct iommu_device'.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Register individual Mediatek IOMMUs to the iommu core and
add sysfs entries.
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
'arm/exynos' into next
|
|
For each subsequent device assigned to the m4u_group after its initial
allocation, we need to take an additional reference. Otherwise, the
caller of iommu_group_get_for_dev() will inadvertently remove the
reference taken by iommu_group_add_device(), and the group will be
freed prematurely if any device is removed.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Convert DT component matching to use component_match_add_release().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Our per-device data consists of the M4U instance and firmware-provided
list of LARB IDs, which is a perfect fit for the generic iommu_fwspec
machinery. Use that directly as a simpler alternative to the custom
archdata code.
CC: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Move the struct defines of mtk iommu into a new header files for
common use.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The device_node will be released in of_iommu_configure, it may be double
released if call of_node_put in mtk_iommu_of_xlate.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
'ppc/pamu', 'core' and 'x86/amd' into next
|
|
Many IOMMUs support multiple page table formats, meaning that any given
domain may only support a subset of the hardware page sizes presented in
iommu_ops->pgsize_bitmap. There are also certain use-cases where the
creator of a domain may want to control which page sizes are used, for
example to force the use of hugepage mappings to reduce pagetable walk
depth.
To this end, add a per-domain pgsize_bitmap to represent the subset of
page sizes actually in use, to make it possible for domains with
different requirements to coexist.
Signed-off-by: Will Deacon <will.deacon@arm.com>
[rm: hijacked and rebased original patch with new commit message]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This patch add 4GB mode support for m4u.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
of_platform_device_create() returns NULL on error, it never returns
error pointers.
Fixes: 0df4fabe208d ('iommu/mediatek: Add mt8173 IOMMU driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The function can return negative value so it should be assigned to signed
variable. The patch changes also type of related i variable to make code
more compact and coherent.
The problem has been detected using patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
When CONFIG_PM is unset, we get a harmless warning for this driver:
drivers/iommu/mtk_iommu.c:665:12: error: 'mtk_iommu_suspend' defined but not used [-Werror=unused-function]
drivers/iommu/mtk_iommu.c:680:12: error: 'mtk_iommu_resume' defined but not used [-Werror=unused-function]
Marking the functions as __maybe_unused gits rid of the two functions
and lets the compiler silently drop the object code, while still
doing syntax checking on them for build-time verification.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0df4fabe208d ("iommu/mediatek: Add mt8173 IOMMU driver")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This patch adds support for mediatek m4u (MultiMedia Memory Management
Unit).
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
