| Age | Commit message (Collapse) | Author |
|---|
|
This adds support for MELPAS MCS5000/MSC5080 touch key controllers.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
ADS7845 is a controller for 5-wire touch screens and somewhat
different from 7846. It requires three serial communications to
accomplish one complete conversion. Unlike 7846 it doesn't allow
Z1-/Z2- position measurement.
The patch extends the ads7846 driver to also support ads7845.
The packet struct is extended to contain needed command and
conversion buffers. ads7846_rx() and ads7846_rx_val() now
differentiate between 7845 and 7846 case. ads7846_probe() is
modified to setup ads7845 specific command and conversion
messages and to switch ads7845 into power-down mode, since
this is needed to be prepared to respond to pendown interrupts.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Tested-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Some input events users such as Android require BTN_TOUCH events.
Implement EV_KEY/BTN_TOUCH and make sure that the release event
is not erroneous scheduled without a preceding valid touch.
Avoid duplicated BTN_TOUCH events, even though input core filters
them.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Avoid additional addressing overhead incurred by word_data transfers.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Tested-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The ad7879 driver is using the old bus method of only supporting one
at a time (I2C or SPI). So refactor it like the other input drivers
that support multiple busses simultaneously.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Tested-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
|
|
This patch adds support for the ET&T TC4UM 4-wire USB touchscreen
controller and tries to reuse the bits for TC5UH controller in kernel
already. Data interface is same.
Tested-by: Roger Pueyo Centelles <rogerpueyo@rogerpueyo.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
On some platforms, for example with GPIO interrupts on mpc5121,
it is not possible to configure falling edge interrupts.
Specifying irq trigger type in platform data structure
allows using ads7846 driver on such platforms.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Stanse found that tsc is dereferenced earlier than checked for being
NULL in tps6507x_ts_remove. Remove the test because there is no way
for tsc to be NULL there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Let's perform be16_to_cpu() conversions once for each received packet,
and then use cached values. Makes code a little bit easier to follow.
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - add Cintiq 21UX2 and Intuos4 WL
Input: ads7846 - fix compiler warning in ads7846_probe()
Input: tps6507x-ts - a couple work queue cleanups
Input: s3c2410_ts - tone down logging
Input: s3c2410_ts - fix build error due to ADC Kconfig rename
|
|
I2C drivers can use the clientdata-pointer to point to private data. As I2C
devices are not really unregistered, but merely detached from their driver, it
used to be the drivers obligation to clear this pointer during remove() or a
failed probe(). As a couple of drivers forgot to do this, it was agreed that it
was cleaner if the i2c-core does this clearance when appropriate, as there is
no guarantee for the lifetime of the clientdata-pointer after remove() anyhow.
This feature was added to the core with commit
e4a7b9b04de15f6b63da5ccdd373ffa3057a3681 to fix the faulty drivers.
As there is no need anymore to clear the clientdata-pointer, remove all current
occurrences in the drivers to simplify the code and prevent confusion.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
This patch fixes the follwing warning introduced by commit
067fb2f648543894ce775082c5636f4c32b99e4f ("Input: ads7846 - return error on
regulator_get() failure"):
drivers/input/touchscreen/ads7846.c: In function 'ads7846_probe':
drivers/input/touchscreen/ads7846.c:1167: warning: format '%ld' expects
type 'long int', but argument 4 has type 'int'
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
1) Use msecs_to_jiffies() instead of calculating by hand.
2) Call cancel_delayed_work_sync() instead of cancel_delayed_work()
followed by a separate flush_workqueue().
3) Remove the "tsc->wq = 0;" Sparse complains about that because
tsc->wq is a pointer, not an int. It's not needed because we just
free the pointer anyway.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The S3C touchscreen driver is logging at LOG_INFO on every stylus up
event which spams the console needlessly. Reduce the priority of the
message to debug level for some peace and quiet.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The name of the Kconfig symbol for the ADC has changed as a result of
application to more SoCs but the select statement has not been updated,
causing linker failures as the ADC core has not been built.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Add touch screen input driver for TPS6507x family of multi-function
chips. Uses the TPS6507x MFD driver. No interrupt support due to
testing limitations of current hardware.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: usbtouchscreen - support bigger iNexio touchscreens
Input: ads7846 - return error on regulator_get() failure
Input: twl4030-vibra - correct the power down sequence
Input: enable onkey driver of max8925
Input: use ABS_CNT rather than (ABS_MAX + 1)
|
|
Without s3c24xx ids driver doesn't attach on s3c2410 and s3c244x
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Bigger Nexio touchscreens not only send more data but also the header
values are modified somewhat. Fix the header (it's a guesswork but
it works at least on one 46" touchscreen with 2.00SMS firmware) and
also increase rept_size.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
In probe(), if regulator_get() failed, an error code was not being
returned causing the driver to be successfully bound, even though
probe failed. This in turn caused the suspend, resume and remove
methods to be registered and accessed via the SPI core. Since these
functions all access private driver data using pointers that had been
freed during the failed probe, this would lead to unpredictable
behavior.
This patch ensures that probe() returns an error code in this failure
case so the driver is not bound.
Found using lockdep and noticing the lock used in the suspend/resum
path pointed to a bogus lock due to the freed memory.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (229 commits)
USB: remove unused usb_buffer_alloc and usb_buffer_free macros
usb: musb: update gfp/slab.h includes
USB: ftdi_sio: fix legacy SIO-device header
USB: kl5usb105: reimplement using generic framework
USB: kl5usb105: minor clean ups
USB: kl5usb105: fix memory leak
USB: io_ti: use kfifo to implement write buffering
USB: io_ti: remove unsused private counter
USB: ti_usb: use kfifo to implement write buffering
USB: ir-usb: fix incorrect write-buffer length
USB: aircable: fix incorrect write-buffer length
USB: safe_serial: straighten out read processing
USB: safe_serial: reimplement read using generic framework
USB: safe_serial: reimplement write using generic framework
usb-storage: always print quirks
USB: usb-storage: trivial debug improvements
USB: oti6858: use port write fifo
USB: oti6858: use kfifo to implement write buffering
USB: cypress_m8: use kfifo to implement write buffering
USB: cypress_m8: remove unused drain define
...
Fix up conflicts (due to usb_buffer_alloc/free renaming) in
drivers/input/tablet/acecad.c
drivers/input/tablet/kbtab.c
drivers/input/tablet/wacom_sys.c
drivers/media/video/gspca/gspca.c
sound/usb/usbaudio.c
|
|
For more clearance what the functions actually do,
usb_buffer_alloc() is renamed to usb_alloc_coherent()
usb_buffer_free() is renamed to usb_free_coherent()
They should only be used in code which really needs DMA coherency.
All call sites have been changed accordingly, except for staging
drivers.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (40 commits)
Input: psmouse - small formatting changes to better follow coding style
Input: synaptics - set dimensions as reported by firmware
Input: elantech - relax signature checks
Input: elantech - enforce common prefix on messages
Input: wistron_btns - switch to using kmemdup()
Input: usbtouchscreen - switch to using kmemdup()
Input: do not force selecting i8042 on Moorestown
Input: Documentation/sysrq.txt - update KEY_SYSRQ info
Input: 88pm860x_onkey - remove invalid irq number assignment
Input: i8042 - add a PNP entry to the aux device list
Input: i8042 - add some extra PNP keyboard types
Input: wm9712 - fix wm97xx_set_gpio() logic
Input: add keypad driver for keys interfaced to TCA6416
Input: remove obsolete {corgi,spitz,tosa}kbd.c
Input: kbtab - do not advertise unsupported events
Input: kbtab - simplify kbtab_disconnect()
Input: kbtab - fix incorrect size parameter in usb_buffer_free
Input: acecad - don't advertise mouse events
Input: acecad - fix some formatting issues
Input: acecad - simplify usb_acecad_disconnect()
...
Trivial conflict in Documentation/feature-removal-schedule.txt
|
|
* 'for-linus/samsung4' of git://git.fluff.org/bjdooks/linux: (98 commits)
Input: s3c24xx_ts - depend on SAMSUNG_DEV_TS and update menu entry
Input: s3c24xx_ts - Add FEAT for Samsung touchscreen support
Input: s3c24xx_ts - Implement generic GPIO configuration callback
ARM: SAMSUNG: Move s3c64xx dev-ts.c to plat-samsung and rename configuration
ARM: SAMSUNG: Implements cfg_gpio function for Samsung touchscreen
ARM: S3C64XX: Add touchscreen platform device definition
ARM: SAMSUNG: Move mach/ts.h to plat/ts.h
ARM: S5PC100: Move i2c helpers from plat-s5pc1xx to mach-s5pc100
ARM: S5PC100: Move frame buffer helpers from plat-s5pc1xx to mach-s5pc100
ARM: S5PC100: gpio.h cleanup
ARM: S5PC100: Move gpio support from plat-s5pc1xx to mach-s5pc100
ARM: S5PC100: Use common functions for gpiolib implementation
drivers: serial: S5PC100 serial driver cleanup
ARM: S5PC100: Pre-requisite clock patch for plat-s5pc1xx to plat-s5p move
ARM: SAMSUNG: Copy common I2C0 device helpers to machine directories
ARM: SAMSUNG: move driver strength gpio configuration helper to common dir
ARM: S5PV210: Add GPIOlib support
ARM: SAMSUNGy: fix broken timer irq base
ARM: SMDK6440: Add audio devices on board
ARM: S5P6440: Add audio platform devices
...
|
|
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (224 commits)
ARM: remove 'select GENERIC_TIME'
ARM: 6136/1: ARCH_REQUIRE_GPIOLIB selects GENERIC_GPIO
ARM: 6074/1: oprofile: convert from sysdev to platform device
ARM: 6073/1: oprofile: remove old files and update KConfig
ARM: 6072/1: oprofile: use perf-events framework as backend
ARM: 6071/1: perf-events: allow modules to query the number of hardware counters
ARM: 6070/1: perf-events: add support for xscale PMUs
ARM: 6069/1: perf-events: use numeric ID to identify PMU
ARM: 6064/1: pmu: register IRQs at runtime
ARM: Optionally allow ARMv6 to use 'normal, bufferable' memory for DMA
ARM: 6134/1: Handle instruction cache maintenance fault properly
ARM: nwfpe: allow debugging output to be configured at runtime
ARM: rename mach_cpu_disable() to platform_cpu_disable()
ARM: 6132/1: PL330: Add common core driver
ARM: 6094/1: Extend cache-l2x0 to support the 16-way PL310
ARM: Move memory mapping into mmu.c
ARM: Ensure meminfo is sorted prior to sanity_check_meminfo
ARM: Remove useless linux/bootmem.h includes
ARM: convert /proc/cpu/aligment to seq_file
arm: use asm-generic/scatterlist.h
...
|
|
Use kmemdup when some other buffer is immediately copied into the
allocated region.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
WM97XX_GPIO_HIGH is not a bitmap and should to be treated as such.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
|
|
Make the driver depend on either ARCH_S3C2410 (as legacy) or the new
device selection of SAMSUNG_DEV_TS.
Change the menuconfig name to reflect this driver is now handling more
devices that just the s3c2410.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
|
|
This patch adds a feature bit field in the touchscreen driver for Samsung SoCs.
Which can be used to distinguish the TSADC module features.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
[ben-linux@fluff.org: minor fix to title]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
|
|
This patch implements generic GPIO configuration function in Samsung
touchscreen driver. And makes the touchscreen driver s3c24xx-ts.c
generic to all the Samsung SoCs.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
[ben-linux@fluff.org: fixed title ]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
|
|
This moves mach-s3c2410/include/mach/ts.h to plat-samsung/include/plat/ts.h in
order to prepare for s3c64xx support in the touchscreen driver.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ad7877 - keep dma rx buffers in seperate cache lines
Input: psmouse - reset all types of mice before reconnecting
Input: elantech - use all 3 bytes when checking version
Input: iforce - fix Guillemot Jet Leader 3D entry
Input: iforce - add Guillemot Jet Leader Force Feedback
|
|
With dma based spi transmission, data corruption is observed
occasionally. With dma buffers located right next to msg and
xfer fields, cache lines correctly flushed in preparation for
dma usage may be polluted again when writing to fields in the
same cache line.
Make sure cache fields used with dma do not share cache lines
with fields changed during dma handling. As both fields are part
of a struct that is allocated via kzalloc, thus cache aligned,
moving the fields to the 1st position and insert padding for
alignment does the job.
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Oliver Schneidewind <osw@emlix.com>
Signed-off-by: Johannes Weiner <jw@emlix.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
[dtor@mail.ru - changed to use ___cacheline_aligned as suggested
by akpm]
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The corgi touchscreen is now deprecated in favour of the generic ads7846.c
driver. The noise reduction technique used in corgi_ts.c, which is to wait
till vsync before ADC sampling, is also integrated into ads7846 driver now.
Provided that the original driver is not generic and is difficult to maintain,
it will be removed now.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: joydev - allow binding to button-only devices
Input: elantech - ignore high bits in the position coordinates
Input: elantech - allow forcing Elantech protocol
Input: elantech - fix firmware version check
Input: ati_remote - add some missing devices from lirc_atiusb
Input: eeti_ts - cancel pending work when going to suspend
Input: Add support of Synaptics Clickpad device
Revert "Input: ALPS - add signature for HP Pavilion dm3 laptops"
Input: psmouse - ignore parity error for basic protocols
|
|
This fixes a race between the suspend code and input events.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Adds support for Hampshire TSHARC serial touchscreens. Implements
Hampshire's 4-byte communication protocol.
Signed-off-by: Adam Bennett <abennett72@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Do not leave dangling client data pointers when unbinding device from the
driver.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The corgi touchscreen is now deprecated in favour of the generic ads7846.c
driver. The noise reduction technique used in corgi_ts.c, which is to wait
till vsync before ADC sampling, is also integrated into ads7846 driver now.
Provided that the original driver is not generic and is difficult to maintain,
it will be removed now.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
Add wakeup support to the ads7846 driver. Platforms can enable wakeup
capability by setting the wakeup flag in ads7846_platform_data. With this
patch the ads7846 driver can be used to wake the system from suspend.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The time interval between consecutive interrupts depends on a number of
tunables: first_conversion_delay, acquisition_time, averaging and foremost
the pen_down_acc_interval.
Since the mod_timer() action for the PEN UP event happens in the
spi_async() callback function, latencies incurred by the spi bus drivers
also need to be taken into account.
So all in all, give the PEN UP event a bit more wiggle room and increase
timeout to 100ms.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The AD7873 is almost identical to the ADS7846; the only difference is
related to the Power Management bits PD0 and PD1. This results in a
slightly different PENIRQ enable behavior. For the AD7873, VREF should
be turned off during differential measurements.
So, add the AD7873/43 to the list of driver supported devices, and prevent
VREF usage during differential/ratiometric conversion modes.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Use genirq to simplify IRQ handling in 88pm860x. Remove the interface of
mask/free IRQs on 88pm860x. All these work is taken by genirq. Update the
touchscreen driver of 88pm860x since IRQ handling is changed.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
