| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a new driver for the Azoteq IQS269A capacitive touch controller
- a new driver for the Cypress CY8CTMA140 touchscreen
- updates to Elan and ft5x06 touchscreen drivers
- assorted driver fixes
- msm-vibrator has been removed as we have a more generic solution
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (28 commits)
Input: adi - work around module name confict
Input: iqs269a - add missing I2C dependency
Input: elants - refactor elants_i2c_execute_command()
Input: elants - override touchscreen info with DT properties
Input: elants - remove unused axes
Input: add support for Azoteq IQS269A
dt-bindings: input: Add bindings for Azoteq IQS269A
Input: imx_sc_key - use devm_add_action_or_reset() to handle all cleanups
Input: remove msm-vibrator driver
dt-bindings: Input: remove msm-vibrator
Input: elants_i2c - provide an attribute to show calibration count
Input: introduce input_mt_report_slot_inactive()
dt-bindings: input: touchscreen: elants_i2c: convert to YAML
Input: add driver for the Cypress CY8CTMA140 touchscreen
dt-bindings: touchscreen: Add CY8CTMA140 bindings
Input: edt-ft5x06 - prefer asynchronous probe
Input: edt-ft5x06 - improve power management operations
Input: edt-ft5x06 - move parameter restore into helper
Input: edt-ft5x06 - fix get_default register write access
Input: atkbd - receive and use physcode->keycode mapping from FW
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Just a few random driver fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - add a second working PNP_ID for Lenovo T470s
Input: applespi - replace zero-length array with flexible-array
Input: axp20x-pek - always register interrupt handlers
Input: lm8333 - update contact email
Input: synaptics-rmi4 - fix error return code in rmi_driver_probe()
Input: synaptics-rmi4 - really fix attn_data use-after-free
Input: i8042 - add ThinkPad S230u to i8042 reset list
Revert "Input: i8042 - add ThinkPad S230u to i8042 nomux list"
Input: dlink-dir685-touchkeys - fix a typo in driver name
Input: xpad - add custom init packet for Xbox One S controllers
Input: evdev - call input_flush_device() on release(), not flush()
Input: i8042 - add ThinkPad S230u to i8042 nomux list
Input: usbtouchscreen - add support for BonXeon TP
Input: cros_ec_keyb - use cros_ec_cmd_xfer_status helper
Input: mms114 - fix handling of mms345l
Input: elants_i2c - support palm detection
|
|
Apply some DRY-ing to elants_i2c_execute_command() callers. This pulls
polling and error printk()s into a single function.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/6c576f688b385235c65b461410a917080d27e825.1587923061.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Allow overriding of information from hardware and support additional
common DT properties like axis inversion. This is required for eg.
Nexus 7 and TF300T where the programmed values in firmware differ
from reality.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
[moved "prop" before DMA buffer]
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/49ea996878264f7c8bde25204e4ddf4b1e85ae71.1587923061.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Driver only ever reports MT events and input_mt_init_slots() sets up
emulated axes already. Clear the capabilities not generated directly
and move MT axes setup, so they are visible by input_mt_init_slots().
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/d5eee8cd305adb144a11264d70da94f7b6570366.1587923061.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Merge for-linus branch to sync Elan touchscreen driver code.
|
|
There is an non-touch case by non-calibration after update firmware.
Elan could know calibrate or not by calibration count.
The value of '0xffff' means we didn't calibrate after update firmware.
If calibrate success, it will plus one and change to '0x0000'.
Signed-off-by: Johnny Chuang <johnny.chuang@emc.com.tw>
Link: https://lore.kernel.org/r/1588754932-5902-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
input_mt_report_slot_state() ignores "tool" argument when the slot is
closed, which has caused a bit of confusion. Let's introduce
input_mt_report_slot_inactive() to report inactive slot state.
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Link: https://lore.kernel.org/r/20200508055656.96389-2-jiada_wang@mentor.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Sync up with mainline to get device tree and other changes.
|
|
This adds a new driver for the Cypress CY8CTMA140 touchscreen.
This driver is inspired by out-of-tree code for the Samsung
GT-S7710 mobile phone.
I have tried to compare the structure and behaviour of this
touchscreen to the existing CYTTSP and CYTTSP4 generics and
it seems pretty different. It is also different in character
from the cy8ctmg110_ts.c. It appears to rather be vaguely
related to the Melfas MMS114 driver, yet distinctly
different.
Dmitry Torokhov rewrote the key scanning code during the
submission process so the driver is a joint work.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200506123435.187432-2-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Probing the device takes a while, because we sleep for 300 ms after a
reset; allow asynchronous probing so this can happen in the background
while other devices are being probed.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20200227112819.16754-5-m.felsch@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
It is possible to bring the device into a deep sleep state. To exit this
state the reset or wakeup pin must be toggeled as documented in [1].
Because of the poor documentation I used the several downstream kernels
[2] and other applications notes [3] to indentify the related registers.
Furthermore I added the support to disable the device completely which
is obviously the most effective power-saving mechanism. This mechanism
needs the reset pin to ensure the power-up/down sequence.
We can't apply any of these power-saving mechanism if both pins are
missing (not connected) or if it is a wakeup device.
[1] https://www.newhavendisplay.com/appnotes/datasheets/touchpanel/FT5x26.pdf
https://www.newhavendisplay.com/appnotes/datasheets/touchpanel/FT5x06.pdf
[2] https://github.com/linux-sunxi/linux-sunxi/blob/sunxi-3.4/drivers/input/touchscreen/ft5x_ts.c
https://github.com/Pablito2020/focaltech-touch-driver/blob/master/ft5336_driver.c
[3] https://www.newhavendisplay.com/appnotes/datasheets/touchpanel/FT5x16_registers.pdf
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20200227112819.16754-4-m.felsch@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
We need to restore the parameters if we switch between the
factory/work mode and during the resume process if we switched off the
power-supply. Therefore refactor edt_ft5x06_work_mode() and move the
"restore the parameters" into a helper routine so we can reuse it later.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20200227112819.16754-3-m.felsch@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Since commit b6eba86030bf ("Input: edt-ft5x06 - add offset support for
ev-ft5726") offset-x and offset-y is supported. Devices using those
offset parameters don't support the offset parameter so we need to add
the NO_REGISTER check for edt_ft5x06_ts_get_defaults().
Fixes: b6eba86030bf ("Input: edt-ft5x06 - add offset support for ev-ft5726")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20200227112819.16754-2-m.felsch@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
MMS345L is another first generation touch screen from Melfas,
which uses mostly the same registers as MMS152.
However, there is some garbage printed during initialization.
Apparently MMS345L does not have the MMS152_COMPAT_GROUP register
that is read+printed during initialization.
TSP FW Rev: bootloader 0x6 / core 0x26 / config 0x26, Compat group: \x06
On earlier kernel versions the compat group was actually printed as
an ASCII control character, seems like it gets escaped now.
But we probably shouldn't print something from a random register.
Add a separate "melfas,mms345l" compatible that avoids reading
from the MMS152_COMPAT_GROUP register. This might also help in case
there is some other device-specific quirk in the future.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Andi Shyti <andi@etezian.org>
Link: https://lore.kernel.org/r/20200423102431.2715-1-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Based on available information this uses the singletouch irtouch
protocol. This is tested and confirmed to be fully functional on
the BonXeon TP hardware I have.
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Link: https://lore.kernel.org/r/20200413184217.55700-1-james.hilliard1@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
MMS345L is another first generation touch screen from Melfas,
which uses the same registers as MMS152.
However, using I2C_M_NOSTART for it causes errors when reading:
i2c i2c-0: sendbytes: NAK bailout.
mms114 0-0048: __mms114_read_reg: i2c transfer failed (-5)
The driver works fine as soon as I2C_M_NOSTART is removed.
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200405170904.61512-1-stephan@gerhold.net
[dtor: removed separate mms345l handling, made everyone use standard
transfer mode, propagated the 10bit addressing flag to the read part of the
transfer as well.]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Elan uses the least significant bit of byte 33 to signal the type of
contact (finger versus palm). The default value is 1 for all firmwares,
which is reported as MT_TOOL_FINGER. If firmware supports palm detection,
the bit will change to 0 and the driver will report such contact as
MT_TOOL_PALM.
Signed-off-by: Johnny Chuang <johnny.chuang@emc.com.tw>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Link: https://lore.kernel.org/r/1585551756-29066-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"An update to the Goodix touchscreen driver to enable it work properly
on various Bay Trail and Cherry Trail devices, and a few other
assorted changes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (26 commits)
Input: update SPDX tag for input-event-codes.h
Input: i8042 - add Acer Aspire 5738z to nomux list
Input: goodix - fix compilation when ACPI support is disabled
dt-bindings: touchscreen: Convert edt-ft5x06 to json-schema
Input: of_touchscreen - explicitly choose axis
Input: goodix - support gt9147 touchpanel
dt-bindings: touchscreen: goodix: support of gt9147
Input: goodix - add support for Goodix GT917S
Input: goodix - use string-based chip ID
dt-bindings: input: touchscreen: add compatible string for Goodix GT917S
Input: goodix - add support for more then one touch-key
Input: goodix - fix spurious key release events
Input: goodix - try to reset the controller if the i2c-test fails
Input: goodix - restore config on resume if necessary
Input: goodix - make goodix_send_cfg() take a raw buffer as argument
Input: goodix - add minimum firmware size check
Input: goodix - save a copy of the config from goodix_read_config()
Input: goodix - move defines to above struct goodix_ts_data declaration
Input: goodix - add support for controlling the IRQ pin through ACPI methods
Input: goodix - add support for getting IRQ + reset GPIOs on Bay Trail devices
...
|
|
Prepare input updates for 5.7 merge window.
|
|
acpi_evaluate_object() and acpi_execute_simple_method() are not part of
the group of ACPI related functions which get stubbed by
include/linux/acpi.h when ACPI support is disabled, so the
IRQ_PIN_ACCESS_ACPI_METHOD handling code must be stubbed out.
For consistency use the same #if condition as which is used to replace
goodix_add_acpi_gpio_mappings with a stub.
Fixes: c5fca485320e ("Input: goodix - add support for controlling the IRQ pin through ACPI methods")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200401014529.GL75430@dtor-ws
[dtor: stubbed out the ACPI method accessors]
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core changes for 5.7-rc1.
Nothing huge in here, just lots of little firmware core changes and
use of new apis, a libfs fix, a debugfs api change, and some driver
core deferred probe rework.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (44 commits)
Revert "driver core: Set fw_devlink to "permissive" behavior by default"
driver core: Set fw_devlink to "permissive" behavior by default
driver core: Replace open-coded list_last_entry()
driver core: Read atomic counter once in driver_probe_done()
libfs: fix infoleak in simple_attr_read()
driver core: Add device links from fwnode only for the primary device
platform/x86: touchscreen_dmi: Add info for the Chuwi Vi8 Plus tablet
platform/x86: touchscreen_dmi: Add EFI embedded firmware info support
Input: icn8505 - Switch to firmware_request_platform for retreiving the fw
Input: silead - Switch to firmware_request_platform for retreiving the fw
selftests: firmware: Add firmware_request_platform tests
test_firmware: add support for firmware_request_platform
firmware: Add new platform fallback mechanism and firmware_request_platform()
Revert "drivers: base: power: wakeup.c: Use built-in RCU list checking"
drivers: base: power: wakeup.c: Use built-in RCU list checking
component: allow missing unbind callback
debugfs: remove return value of debugfs_create_file_size()
debugfs: Check module state before warning in {full/open}_proxy_open()
firmware: fix a double abort case with fw_load_sysfs_fallback
arch_topology: Fix putting invalid cpu clk
...
|
|
The 'axis + 1' calculation is implicit and potentially error prone.
Moreover, few lines before the axis is set explicitly for both X and Y.
Do the same when retrieving different properties for X and Y.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200303180917.12563-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Add support for it by adding compatible and supported chip data
(default settings used).
The chip data on GT9147 is similar to GT912, like
- config data register has 0x8047 address
- config data register max len is 240
- config data checksum has 8-bit
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/1583144308-3781-3-git-send-email-yannick.fertre@st.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Goodix GT917S is a touchscreen chip from Goodix that is in the GT1x
family.
Add its support by assigning the gt1x config to it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200228010146.12215-4-icenowy@aosc.io
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
For Goodix GT917S chip, the chip ID string is "917S", which contains not
only numbers now.
Use string-based chip ID in the driver to support this chip and further
chips with alphanumber ID.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200228010146.12215-3-icenowy@aosc.io
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Some devices with a goodix touchscreen have more then 1 capacitive
touch-key. This commit replaces the current support for a single
touch-key, which ignored the reported key-code. With support for
up to 7 touch-keys, based upon checking the key-code which is
post-fixed to any reported touch-data.
KEY_LEFTMETA is assigned to the first touch-key (it will still be
the default keycode for devices with a single touch-key).
KEY_F1, KEY_F2... are assigned as default keycode for the other
touch-keys.
This commit also add supports for keycode remapping, so that
systemd-udev's hwdb can be used to remap the codes to send
keycodes to match the icons on the buttons for devices with more
then 1 touch-key.
Signed-off-by: Dmitry Mastykin <dmastykin@astralinux.ru>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200316075302.3759-1-dmastykin@astralinux.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The goodix panel sends spurious interrupts after a 'finger up' event,
which always cause a timeout.
We were exiting the interrupt handler by reporting touch_num == 0, but
this was still processed as valid and caused the code to use the
uninitialised point_data, creating spurious key release events.
Report an error from the interrupt handler so as to avoid processing
invalid point_data further.
Signed-off-by: Dmitry Mastykin <dmastykin@astralinux.ru>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200316075302.3759-2-dmastykin@astralinux.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
On some ACPI/x86 devices (where we use one of the ACPI IRQ pin access
methods) the firmware is buggy, it does not properly reset the controller
at boot, and we cannot communicate with it.
Normally on ACPI/x86 devices we do not want to reset the controller at
probe time since in some cases this causes the controller to loose its
configuration and this is loaded into it by the system's firmware.
So on these systems we leave the reset_controller_at_probe flag unset,
even though we have a access to both the IRQ and reset pins and thus
could reset it.
In the case of the buggy firmware we have to reset the controller to
actually be able to talk to it.
This commit adds a special case for this, if the goodix_i2c_test() fails,
and we have not reset the controller yet; and we do have a way to reset
the controller then retry the i2c-test after resetting the controller.
This fixes the driver failing at probe on ACPI/x86 systems with this
firmware bug.
Reported-and-tested-by: Dmitry Mastykin <dmastykin@astralinux.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200311191013.10826-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Some devices, e.g the Trekstor Primetab S11B, lose there config over
a suspend/resume cycle (likely the controller loses power during suspend).
This commit reads back the config version on resume and if matches the
expected config version it resets the controller and resends the config
we read back and saved at probe time.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-11-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Make goodix_send_cfg() take a raw buffer as argument instead of a
struct firmware *cfg, so that it can also be used to restore the config
on resume if necessary.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-10-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Our goodix_check_cfg_* helpers do things like:
int i, raw_cfg_len = cfg->size - 2;
...
if (check_sum != cfg->data[raw_cfg_len]) {
When cfg->size < 2, this will end up indexing the cfg->data array with
a negative value, which will not end well.
To fix this this commit adds a new GOODIX_CONFIG_MIN_LENGTH define and
adds a minimum size check for firmware-config files using this new define.
For consistency this commit also adds a new GOODIX_CONFIG_GT9X_LENGTH for
the length used for recent gt9xx and gt1xxx chips, instead of using
GOODIX_CONFIG_MAX_LENGTH for this, so that if other length defines get
added in the future it will be clear that the MIN and MAX defines should
contain the min and max values of all the other defines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200307121505.3707-9-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Save a copy of the config in goodix_read_config(), this is a preparation
patch for restoring the config if it was lost after a supend/resume cycle.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-8-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Move the defines to above the struct goodix_ts_data declaration, so
that the MAX defines can be used inside the struct goodix_ts_data
declaration. No functional changes, just moving a block of code.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-7-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Some Apollo Lake (x86, UEFI + ACPI) devices only list the reset GPIO
in their _CRS table and the bit-banging of the IRQ line necessary to
wake-up the controller from suspend can be done by calling 2 Goodix
custom / specific ACPI methods.
This commit adds support for controlling the IRQ line in this matter,
allowing us to properly suspend the touchscreen controller on such
devices.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-6-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
On most Bay Trail (x86, UEFI + ACPI) devices the ACPI tables do not have
a _DSD with a "daffd814-6eba-4d8c-8a91-bc9bbf4aa301" UUID, adding
"irq-gpios" and "reset-gpios" mappings, so we cannot get the GPIOS by name
without first manually adding mappings ourselves.
These devices contain 2 GpioIo resource in their _CRS table, on all 4 such
devices which I have access to, the order of the 2 GPIOs is reset, int.
Note that the GPIO to which the touchscreen controller irq pin is connected
is configured in direct-irq mode on these Bay Trail devices, the
pinctrl-baytrail.c driver still allows controlling the pin as a GPIO in
this case, but this is not necessarily the case on other X86 ACPI
platforms, nor do we have a guarantee that the GPIO order is the same
elsewhere, so we limit the use of a _CRS table with 2 GpioIo resources
to Bay Trail devices only.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-5-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
devices
On most Cherry Trail (x86, UEFI + ACPI) devices the ACPI tables do not have
a _DSD with a "daffd814-6eba-4d8c-8a91-bc9bbf4aa301" UUID, adding
"irq-gpios" and "reset-gpios" mappings, so we cannot get the GPIOS by name
without first manually adding mappings ourselves.
These devices contain 1 GpioInt and 1 GpioIo resource in their _CRS table:
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (RBUF, ResourceTemplate ()
{
I2cSerialBusV2 (0x0014, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.PCI0.I2C2",
0x00, ResourceConsumer, , Exclusive,
)
GpioInt (Edge, ActiveLow, Shared, PullDefault, 0x0000,
"\\_SB.GPO1", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0013
}
GpioIo (Shared, PullDefault, 0x0000, 0x0000,
IoRestrictionOutputOnly,
"\\_SB.GPO1", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0019
}
})
Return (RBUF) /* \_SB_.PCI0.I2C2.TCS1._CRS.RBUF */
}
There is no fixed order for these 2. This commit adds code to check that
there is 1 of each as expected and then registers a mapping matching their
order using devm_acpi_dev_add_driver_gpios().
This gives us access to both GPIOs allowing us to properly suspend the
controller during suspend, and making it possible to reset the controller
if necessary.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200307121505.3707-4-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
GPIO setup
Before this commit we would always reset the controller at probe when we
have access to the GPIOs which are necessary to do a reset.
Doing the reset requires access to the GPIOs, but just because we have
access to the GPIOs does not mean that we should always reset the
controller at probe. On X86 ACPI platforms the BIOS / UEFI firmware will
already have reset the controller and it will have loaded the device
specific config into the controller. Doing the reset sometimes causes the
controller to lose its configuration, so on X86 ACPI platforms this is not
a good idea.
This commit adds a new reset_controller_at_probe boolean to control the
reset at probe behavior.
This commits sets the new bool to true when we set irq_pin_access_method
to IRQ_PIN_ACCESS_GPIO, so there are no functional changes.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
setup
At least on X86 ACPI platforms it is not necessary to load the touchscreen
controller config from disk, if it needs to be loaded this has already been
done by the BIOS / UEFI firmware.
Even on other (e.g. devicetree) platforms the config-loading as currently
done has the issue that the loaded cfg file is based on the controller
model, but the actual cfg is device specific, so the cfg files are not
part of linux-firmware and this can only work with a device specific OS
image which includes the cfg file.
And we do not need access to the GPIOs at all to load the config, if we
do not have access we can still load the config.
So all in all tying the decision to try to load the config from disk to
being able to access the GPIOs is not desirable. This commit adds a new
load_cfg_from_disk boolean to control the firmware loading instead.
This commits sets the new bool to true when we set irq_pin_access_method
to IRQ_PIN_ACCESS_GPIO, so there are no functional changes.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
So far we have only effectively supported this on devices which use
devicetree. On X86 ACPI platforms both looking up the pins; and using a
pin as both IRQ and GPIO is a bit more complicated. E.g. on some devices
we cannot directly access the IRQ pin as GPIO and we need to call ACPI
methods to control it instead.
This commit adds a new irq_pin_access_method field to the goodix_chip_data
struct and adds goodix_irq_direction_output and goodix_irq_direction_input
helpers which together abstract the GPIO accesses to the IRQ pin.
This is a preparation patch for adding support for properly suspending the
touchscreen on X86 ACPI platforms.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200307121505.3707-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Unfortunately sofar we have been unable to get permission to redistribute
icn8505 touchscreen firmwares in linux-firmware. This means that people
need to find and install the firmware themselves before the touchscreen
will work
Some UEFI/x86 tablets with an icn8505 touchscreen have a copy of the fw
embedded in their UEFI boot-services code.
This commit makes the icn8505 driver use the new firmware_request_platform
function, which will fallback to looking for such an embedded copy when
direct filesystem lookup fails. This will make the touchscreen work OOTB
on devices where there is a fw copy embedded in the UEFI code.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200115163554.101315-9-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Unfortunately sofar we have been unable to get permission to redistribute
Silead touchscreen firmwares in linux-firmware. This means that people
need to find and install the firmware themselves before the touchscreen
will work
Some UEFI/x86 tablets with a Silead touchscreen have a copy of the fw
embedded in their UEFI boot-services code.
This commit makes the silead driver use the new firmware_request_platform
function, which will fallback to looking for such an embedded copy when
direct filesystem lookup fails. This will make the touchscreen work OOTB
on devices where there is a fw copy embedded in the UEFI code.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200115163554.101315-8-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These functions are supposed to return negative error codes but instead
it returns true on failure and false on success. The error codes are
eventually propagated back to user space.
Fixes: 48a2b783483b ("Input: add Raydium I2C touchscreen driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200303101306.4potflz7na2nn3od@kili.mountain
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This patch supports reporting resolution for ABS_MT_TOUCH_MAJOR event.
This information is needed in showing pressure/width radius.
Signed-off-by: Johnny Chuang <johnny.chuang@emc.com.tw>
Reviewed-by: Harry Cutts <hcutts@chromium.org>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/1582766000-23023-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The touchscreen on the Cube I15-TC don't match the default display,
with 0,0 touches being reported when touching at the top-right of
the screen.
Add a quirk to invert the x coordinate.
Reported-and-tested-by: Arkadiy <arkan49@yandex.ru>
Signed-off-by: Sergei A. Trusov <sergei.a.trusov@ya.ru>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This adds support for the Ilitek ili2120 touchscreen found in the
Fairphone 2 smartphone.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20200209151904.661210-1-luca@z3ntu.xyz
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The is_visible function expects the permissions associated with an
attribute of the sysfs group or 0 if an attribute is not visible.
Change the code to return the attribute permissions when the attribute
should be visible which resolves the warning:
Attribute calibrate: Invalid permissions 01
Fixes: cc12ba1872c6 ("Input: ili210x - optionally show calibrate sysfs attribute")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com>
Link: https://lore.kernel.org/r/20200209145628.649409-1-luca@z3ntu.xyz
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Prepare input updates for 5.6 merge window.
|
|
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272df6485 ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20191210141103.15910-1-alexandru.ardelean@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Sync up with mainline to get SPI "delay" API changes.
|
