Age | Commit message (Collapse) | Author |
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced the "Fallthrough state"
commern with a proper "Fall through", which is what GCC is expecting to
find.
Addresses-Coverity-ID: 114758 ("Missing break in switch")
Addresses-Coverity-ID: 114759 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Apart from whitespace differences, this block of macros is repeated
twice:
$ x=./drivers/input/mouse/cyapa_gen3.c; diff -w -u <(sed -n '139,181p' $x) <(sed -n '182,224p' $x)
$
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. Fix up the 50ms delays here to use msleep() and
reduce the load on the hrtimer subsystem.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Using counter based retry loops for peripherals results in the delay
being significantly overrun during high-load situations where delay
functions tend to be vary imprecise and overrun there timeouts. So
condition the termination on the actual condition of 2s for the
re-calibration to have been successful.
As this is a very long delay there is no advantage in using
high-resolution timers thus switching this to msleep().
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
When changing the scan rate as part of runtime-resume process we may lose
some of the events, because:
1) for gen3 trackpads, the driver must msleep() some time to ensure that
the device is ready to accept next command;
2) for gen5 and later trackpads, the queue dumping function will simply
ignore the events when waiting for the set power mode command response.
The solution is to keep polling and report those valid events when the set
power mode command is in progress.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Fix the the runtime suspend power management not working issue when system
starts up and before user touches the trackpad device.
TEST=test on Chromebook.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Gen5 and Gen6 trackpad devices are able to detect and report object
proximity data/events, add this function support in the cyapa driver
through the ABS_DISTANCE event.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Change 'gen5' to 'pip' for all macros, variables and functions that are
shared between gen5 and gen6 modules to make naming more clear and
readable.
Also fix a few spelling errors.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
As the name suggests, always_unused argument in cyapa_gen3_set_power_mode()
is never used, so there is no reason for setting it to 0.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Use asm/unaligned.h instead of linux/unaligned/access_ok.h header file to
fix compiling issues such as following while doing cross platform
compiling:
"include/linux/unaligned/access_ok.h:7:19: error: redefinition of
'get_unaligned_le16'
...
include/linux/unaligned/le_struct.h:6:19: note: previous definition of
'get_unaligned_le16' was here".
Reported-by: kbuild test robot <kbuild-all@01.org>
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Add force re-calibrate function support for gen3 trackpad device, it can be
used through sysfs calibrate interface.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Add read baseline function supported for gen3 trackpad device, it can be
used through sysfs baseline interface.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Add support for firmware image update for gen3 trackpad devices; the
firmware update is initiated by writing to update_fw sysfs attribute.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
In order to support multiple different chipsets and communication protocols
trackpad devices in one cyapa driver, the new cyapa driver is re-designed
with one cyapa driver core and multiple device specific functions component.
The cyapa driver core is contained in this patch, it supplies basic functions
that working with kernel and input subsystem, and also supplies the interfaces
that the specific devices' component can connect and work together with as
one driver.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|