| Age | Commit message (Collapse) | Author |
|---|
|
The "lg" variable is declared as int so in all places where
this variable is used as a shift operand, the output will be
int too.
This produces the following smatch warning:
drivers/infiniband/hw/mthca/mthca_cmd.c:701 mthca_map_cmd() warn:
should '1 << lg' be a 64 bit type?
Simple declaration of "1" to be "1ULL" will fix the issue.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Peter Senna Tschudin <peter.senna@collabora.com>
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Tested-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch series primarily increases sizes of variables that hold
lid values from 16 to 32 bits. Additionally, it adds a check in
the IB mad stack to verify a properly formatted MAD when OPA
extended LIDs are used.
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
slid field in struct ib_wc is increased to 32 bits.
This enables core components to use larger LIDs if needed.
The user ABI is unchanged and return 16 bit values when queried.
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The mthca driver didn't check supplied pointer to functions
mthca_cmd_poll() and mthca_cmd_wait(). This caused to the following
smatch errors:
drivers/infiniband/hw/mthca/mthca_cmd.c:371 mthca_cmd_poll() error: we previously assumed 'out_param' could be null (see line 353)
drivers/infiniband/hw/mthca/mthca_cmd.c:454 mthca_cmd_wait() error: we previously assumed 'out_param' could be null (see line 432)
In reality all callers of these functions are setting out_is_imm
flag are providing pointer too. However it is better to check
again to remove smatch errors to achieve warning free subsystem.
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The process_mad device function declares some parameters as "in". Make those
parameters const and adjust the call tree under process_mad in the various
drivers accordingly.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
They had been getting it implicitly via device.h but we can't
rely on that for the future, due to a pending cleanup so fix
it now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Instead of having firmware command functions return an error and also
a status, leading to code like:
err = mthca_FW_COMMAND(..., &status);
if (err)
goto out;
if (status) {
err = -E...;
goto out;
}
all over the place, just handle the FW status inside the FW command
handling code (the way mlx4 does it), so we can simply write:
err = mthca_FW_COMMAND(...);
if (err)
goto out;
In addition to simplifying the source code, this also saves a healthy
chunk of text:
add/remove: 0/0 grow/shrink: 10/88 up/down: 510/-3357 (-2847)
function old new delta
static.trans_table 324 584 +260
mthca_cmd_poll 352 477 +125
mthca_cmd_wait 511 567 +56
mthca_table_put 213 240 +27
mthca_cleanup_db_tab 372 387 +15
__mthca_remove_one 314 323 +9
mthca_cleanup_user_db_tab 275 283 +8
__mthca_init_one 1738 1746 +8
mthca_cleanup 20 21 +1
mthca_MAD_IFC 1081 1082 +1
mthca_MGID_HASH 43 40 -3
mthca_MAP_ICM_AUX 23 20 -3
mthca_MAP_ICM 19 16 -3
mthca_MAP_FA 23 20 -3
mthca_READ_MGM 43 38 -5
mthca_QUERY_SRQ 43 38 -5
mthca_QUERY_QP 59 54 -5
mthca_HW2SW_SRQ 43 38 -5
mthca_HW2SW_MPT 60 55 -5
mthca_HW2SW_EQ 43 38 -5
mthca_HW2SW_CQ 43 38 -5
mthca_free_icm_table 120 114 -6
mthca_query_srq 214 206 -8
mthca_free_qp 662 654 -8
mthca_cmd 38 28 -10
mthca_alloc_db 1321 1311 -10
mthca_setup_hca 1067 1055 -12
mthca_WRITE_MTT 35 22 -13
mthca_WRITE_MGM 40 27 -13
mthca_UNMAP_ICM_AUX 36 23 -13
mthca_UNMAP_FA 36 23 -13
mthca_SYS_DIS 36 23 -13
mthca_SYNC_TPT 36 23 -13
mthca_SW2HW_SRQ 35 22 -13
mthca_SW2HW_MPT 35 22 -13
mthca_SW2HW_EQ 35 22 -13
mthca_SW2HW_CQ 35 22 -13
mthca_RUN_FW 36 23 -13
mthca_DISABLE_LAM 36 23 -13
mthca_CLOSE_IB 36 23 -13
mthca_CLOSE_HCA 38 25 -13
mthca_ARM_SRQ 39 26 -13
mthca_free_icms 178 164 -14
mthca_QUERY_DDR 389 375 -14
mthca_resize_cq 1063 1048 -15
mthca_unmap_eq_icm 123 107 -16
mthca_map_eq_icm 396 380 -16
mthca_cmd_box 90 74 -16
mthca_SET_IB 433 417 -16
mthca_RESIZE_CQ 369 353 -16
mthca_MAP_ICM_page 240 224 -16
mthca_MAP_EQ 183 167 -16
mthca_INIT_IB 473 457 -16
mthca_INIT_HCA 745 729 -16
mthca_map_user_db 816 798 -18
mthca_SYS_EN 157 139 -18
mthca_cleanup_qp_table 78 59 -19
mthca_cleanup_eq_table 168 149 -19
mthca_UNMAP_ICM 143 121 -22
mthca_modify_srq 172 149 -23
mthca_unmap_fmr 198 174 -24
mthca_query_qp 814 790 -24
mthca_query_pkey 343 319 -24
mthca_SET_ICM_SIZE 34 10 -24
mthca_QUERY_DEV_LIM 1870 1846 -24
mthca_map_cmd 1130 1105 -25
mthca_ENABLE_LAM 401 375 -26
mthca_modify_port 247 220 -27
mthca_query_device 884 850 -34
mthca_NOP 75 41 -34
mthca_table_get 287 249 -38
mthca_init_qp_table 333 293 -40
mthca_MODIFY_QP 348 308 -40
mthca_close_hca 131 89 -42
mthca_free_eq 435 390 -45
mthca_query_port 755 705 -50
mthca_free_cq 581 528 -53
mthca_alloc_icm_table 578 524 -54
mthca_multicast_attach 1041 986 -55
mthca_init_hca 326 271 -55
mthca_query_gid 487 431 -56
mthca_free_srq 524 468 -56
mthca_free_mr 168 111 -57
mthca_create_eq 1560 1501 -59
mthca_multicast_detach 790 728 -62
mthca_write_mtt 918 854 -64
mthca_register_device 1406 1342 -64
mthca_fmr_alloc 947 883 -64
mthca_mr_alloc 652 582 -70
mthca_process_mad 1242 1164 -78
mthca_dev_lim 910 830 -80
find_mgm 482 400 -82
mthca_modify_qp 3852 3753 -99
mthca_init_cq 1281 1181 -100
mthca_alloc_srq 1719 1610 -109
mthca_init_eq_table 1807 1679 -128
mthca_init_tavor 761 491 -270
mthca_init_arbel 2617 2098 -519
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.de>
|
|
Some systems have PCI addresses that don't fit in unsigned long (eg some
32-bit PowerPC 440 systems have 36-bit bus addresses). Fix up the driver
by using phys_addr_t where appropriate, so we don't truncate any PCI
resource addresses before ioremapping them.
Signed-off-by: John L. Burr <jlburr@cadence.com>
[ Update to apply to current driver source. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Change abbreviated IB_QPT_RAW_ETY to IB_QPT_RAW_ETHERTYPE to make
the special QP type easier to understand.
cf http://www.mail-archive.com/linux-rdma@vger.kernel.org/msg04530.html
Signed-off-by: Aleksey Senin <alekseys@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
The current MTT allocator uses kmalloc() to allocate a buffer for its
buddy allocator, and thus is limited in the amount of MTT segments
that it can control. As a result, the size of memory that can be
registered is limited too. This patch uses a module parameter to
control the number of MTT entries that each segment represents,
allowing more memory to be registered with the same number of
segments.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Commands INIT_HCA, CLOSE_HCA, SYS_EN, SYS_DIS, and CLOSE_IB all have 1
second timeouts. For INIT_HCA this causes problems when had more than
2^18 are QPs configured, since the command takes more than 1 second to
complete.
All other commands have 60-second timeouts. This patch makes the
above commands consistent with the rest of the commands (and with the
chip documentation).
This patch is an expansion of a patch from Arthur Kepner
<akepner@sgi.com> fixing just the INIT_HCA timeout.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
They don't get updated by git and so they're worse than useless.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Arbel and Sinai devices support checksum generation and verification
of TCP and UDP packets for UD IPoIB messages. This patch checks if
the HCA supports this and sets the IB_DEVICE_UD_IP_CSUM capability
flag if it does. It implements support for handling the IB_SEND_IP_CSUM
send flag and setting the csum_ok field in receive work completions.
Signed-off-by: Eli Cohen <eli@mellnaox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Fix a few whitespace and other coding style problems.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
For memfree devices, the firmware QUERY_ADAPTER command does not
return vendor_id, device_id, and revision_id; do not return these
fields in the QUERY_ADAPTER function for memfree devices.
Instead, for memfree devices, initialize the rev_id field of the mthca
device via init_node_data (MAD IFC query), as is done in the
query_device verb implementation.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Firmware commands are sent to the HCA by writing multiple words to a
command register block. Access to this block of registers is
serialized with a mutex. However, on large SGI systems, problems were
seen with multiple CPUs issuing FW commands at the same time, because
the writes to the register block may be reordered within the system
interconnect and reach the HCA in a different order than they were
issued (even with the mutex). Fix this by adding an mmiowb() before
dropping the mutex.
Tested-by: Arthur Kepner <akepner@sgi.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The FW command token is currently only updated on a command completion
event. This means that on command timeout, the same token will be
reused for new command, which results in a mess if the timed out
command *does* eventually complete.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
s/signifant/significant/
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
First thing mm.h does is including sched.h solely for can_do_mlock() inline
function which has "current" dereference inside. By dealing with can_do_mlock()
mm.h can be detached from sched.h which is good. See below, why.
This patch
a) removes unconditional inclusion of sched.h from mm.h
b) makes can_do_mlock() normal function in mm/mlock.c
c) exports can_do_mlock() to not break compilation
d) adds sched.h inclusions back to files that were getting it indirectly.
e) adds less bloated headers to some files (asm/signal.h, jiffies.h) that were
getting them indirectly
Net result is:
a) mm.h users would get less code to open, read, preprocess, parse, ... if
they don't need sched.h
b) sched.h stops being dependency for significant number of files:
on x86_64 allmodconfig touching sched.h results in recompile of 4083 files,
after patch it's only 3744 (-8.3%).
Cross-compile tested on
all arm defconfigs, all mips defconfigs, all powerpc defconfigs,
alpha alpha-up
arm
i386 i386-up i386-defconfig i386-allnoconfig
ia64 ia64-up
m68k
mips
parisc parisc-up
powerpc powerpc-up
s390 s390-up
sparc sparc-up
sparc64 sparc64-up
um-x86_64
x86_64 x86_64-up x86_64-defconfig x86_64-allnoconfig
as well as my two usual configs.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The reserved_mtts field has different meaning in Tavor and Arbel, so
we are wasting mtt entries on memfree. Fix the Arbel case to match
Tavor semantics.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
struct ib_wc currently only includes the local QP number: this matches
the IB spec, but seems mostly useless. The following patch replaces
this with the pointer to qp itself, and updates all low level drivers
and all users.
This has the following advantages:
- Ability to get a per-qp context through wc->qp->qp_context
- Existing drivers already have the qp pointer ready in poll cq, so
this change actually saves a tiny bit (extra memory read) on data path
(for ehca it would actually be expensive to find the QP pointer when
polling a CQ, but ehca does not support SRQ so we can leave wc->qp as
NULL for ehca)
- Users that need the QP number can still get it through wc->qp->qp_num
Use case:
In IPoIB connected mode code, I have a common CQ shared by multiple
QPs. To track connection usage, I need a way to get at some per-QP
context upon the completion, and I would like to avoid allocating
context object per work request just to stick a QP pointer into it.
With this code, I can just use wc->qp->qp_context.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Several fields in an incoming MAD extended info header were passed
into the MAD_IFC firmware command at incorrect offsets (mostly off by
4 bytes). As the result, the HCA will fail to generate traps in which
this info is needed (e.g. traps which include the GRH of the incoming
packet), in violation of the IB spec.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Signed-off-by: James Lentini <jlentini@netapp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Read the max_cmds value from the response to the QUERY_FW command
before printing out the value, so that the real value goes into the
debug output.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The kernel has had wait_for_completion_timeout() for a long time now.
mthca should use it to handle FW commands timing out, instead of
implementing the same thing in a much more complicated way by using
wait_for_completion() along with a timer that does complete().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Setting fw_cmd_doorbell allows FW command to be queued using posted
writes instead of requiring polling on a "go" bit, so it should be a
performance boost. However, the option causes problems with at least
some device/firmware combinations, so set the default to 0 until we
understand what's going on better.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Push translation of static rate to HCA format into low-level drivers,
where it belongs. For static rate encoding, use encoding of rate
field from IB standard PathRecord, with addition of value 0, for
backwards compatibility with current usage. The changes are:
- Add enum ib_rate to midlayer includes.
- Get rid of static rate translation in IPoIB; just use static rate
directly from Path and MulticastGroup records.
- Update mthca driver to translate absolute static rate into the
format used by hardware. This also fixes mthca's static rate
handling for HCAs that are capable of 4X DDR.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Sinai (one-port PCI Express) HCAs get improved throughput for messages
bigger than 80 KB in DDR mode if memory keys are formatted in a
specific way. The enhancement only works if the memory key table is
smaller than 2^24 entries. For larger tables, the enhancement is off
and a warning is printed (to avoid silent performance loss).
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Michael Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Use a named enum for the HCA's internal page size, rather than having
magic values of 4096 and shifts by 12 all over the code. Also, fix
one minor bug in EQ handling: only one HCA page is mapped to the HCA
during initialization, but a full kernel page is unmapped during
cleanup. This might cause problems when PAGE_SIZE != 4096.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This patch is checks whether the HCA supports posting FW commands
through a doorbell page (user access region 0, or "UAR0"). If this is
supported, the driver maps UAR0 and uses it for FW commands. This can
be controlled by the value of a writable module parameter
fw_cmd_doorbell. When the parameter is 0, the commands are posted
through HCR using the old method; otherwise if HCA is capable commands
go through UAR0.
This use of UAR0 to post commands eliminates the need for polling the
"go" bit prior to posting a new command. Since reading from a PCI
device is much more expensive then issuing a posted write, it is
expected that issuing FW commands this way will provide better CPU
utilization.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Implement the query_qp and query_srq methods in mthca.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Use ib_modify_qp_is_ok() in mthca, and delete the big table of
attributes for queue pair state transitions.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Add low-level driver support to ib_mthca so that consumers can request
a "send queue drained" event be generated when a transiton to the SQD
state completes.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Remove trailing whitespace and fix indentation that with spaces
instead of tabs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Add low-level driver support for resizing CQs (both kernel and
userspace) to mthca.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
When debugging is enabled, the mthca_QUERY_DEV_LIM() firmware command
function prints out some of the device limits that it queries.
However the debugging prints happen before all of the fields are
extracted from the firmware response, so some of the values that get
printed are uninitialized junk. Move the prints to the end of the
function to fix this.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Convert semaphores to mutexes in mthca. Leave firmware command
interface poll_sem and event_sem as semaphores.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
We have run into the following problem: if a task receives a signal
while in the process of e.g. destroying a resource (which could be
because the relevant file was closed) mthca could bail out from trying
to take a command interface semaphore without performing the
appropriate command to tell hardware that the resource is being
destroyed.
As a result we see messages like
ib_mthca 0000:04:00.0: HW2SW_CQ failed (-4)
In this case, hardware could access the resource after the memory has
been freed, possibly causing memory corruption.
A simple solution is to replace down_interruptible() by down() in
command interface activation.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
[ It's also not safe to bail out on multicast table operations, since
they may be invoked on the cleanup path too. So use down() for
mcg_table.sem too. ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Use the ALIGN macro to simplify some rounding code.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Convert "/ (1 << lg)" to ">> lg" for a slight code size reduction.
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-24 (-24)
function old new delta
mthca_map_cmd 613 589 -24
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Unlike tavor, the max work queue size is an exact power of 2 for arbel
mode, despite what the documentation (of the QUERY_DEV_LIM firmware
command) says. Without this patch, on Arbel, we can start with a QP
of a valid size and get above the reported limit after rounding to the
next power of two.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Move the computation of QP capabilities (max scatter/gather entries,
max inline data, etc) into the kernel, and have the uverbs module
return the values as part of the create QP response. This keeps
precise knowledge of device limits in the low-level kernel driver.
This requires an ABI bump, so while we're making changes, get rid of
the max_sge parameter for the modify SRQ command -- it's not used and
shouldn't be there.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add some initial support for detecting and reporting catastrophic
errors reported by Mellanox HCAs. We start a periodic timer which
polls the catastrophic error reporting buffer in device memory. If an
error is detected, we dump the contents of the buffer for port-mortem
debugging, and report a fatal asynchronous error to higher levels.
In the future we can try to recover from these errors by resetting the
device, but this will require some work in higher-level code as well.
Let's get this in now, so that we at least get catastrophic errors
reported in logs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Check the sizes of CQs, QPs and SRQs when creating objects, and fail
instead of creating too-big queues. Also return real limits instead
of just plausible-sounding values from mthca_query_device().
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The loop in mthca_map_cmd() would fill one entry past the end of the
mailbox buffer before calling the firmware command.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Move the InfiniBand headers from drivers/infiniband/include to include/rdma.
This allows InfiniBand-using code to live elsewhere, and lets us remove the
ugly EXTRA_CFLAGS include path from the InfiniBand Makefiles.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
