| Age | Commit message (Collapse) | Author |
|---|
|
The whole IIO subsystem can be built as modules. If you make it a
module then stuff marked as "Y" in the adc directory simply won't be
linked in properly.
The two configs that were wrong were EXYNOS_ADC and LP8788_ADC. I
know for a fact that EXYNOS_ADC will work as a module. I assume
LP8788_ADC will also be fine.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Using pdev->dev with device_for_each_child() would iterate over all
of the children of the platform device and delete them.
Thus, causing crashes during module unload.
We should be using the indio_dev->dev structure for
registering/unregistering child nodes.
Reported-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The driver segfaults when the kernel boots with device tree as the
platform data is then not present and the pointer is deferenced without
checking it is not null. This patch introduces such a check avoiding the
crash.
Signed-off-by: Atilla Filiz <atilla.filiz@essensium.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First found of IIO fixes for the 3.15 cycle.
* Fix the platform data support for the at91 adc driver.
* A couple of related follow up patches get the support working again
for at91sam9260 and at91sam9g45 as the earlier patch results in a device
name change.
* A default timer value in the at91 adc driver was bonkers. Make it sane.
* Fix incorrect reporting of the integration time for the cm32181 light sensor
* Fix a missing break in the ad2s1200 driver which would have give a false
error return.
* Make sure buffer scan mask queries from userspace return 0/1 rather than
a fairly random value depending on their implementation of test_bit
* Fix leak of the i2c client and a null pointer dereference in the cm36651
driver.
* Fix a build warning on avr32 for the mxs-lradc (not exactly a critical
combination - but the issue was real).
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Changes to existing drivers:
- Use of managed resources - omap, twl4030, ti_am335x_tscadc
- Advanced error handling - omap
- Rework clk management - omap
- Device Tree (re-)work - tc3589x, pm8921, da9055, sec
- IRC management overhaul and !BROKEN - pm8921
- Convert to regmap - ssbi, pm8921
- Use simple power-management ops - ucb1x00
- Include file clean-up - adp5520, cs5535, janz, lpc_ich,
- lpc_sch, max14577, mcp-sa11x0, pcf50633-adc, rc5t583,
rdc321x-southbridge, retu, smsc-ece1099, ti-ssp, ti_am335x_tscadc,
tps65912, vexpress-config, wm8350, ywm8350
- Various bug fixes across the subsystem
- NULL/invalid pointer dereference prevention
- Resource leak mitigation,
- Variable used initialised
- Staticise various containers
- Enforce return value checks
New drivers/supported devices:
- Add support for s2mps14 and s2mpa01 to sec
- Add support for da9063 (v5) to da9063
- Add support for atom-c2000 to gpio-ich
- Add support for come-{mbt10,cbt6,chl6} to kempld
- Add support for da9053 to da9052
- Add support for itco-wdt (v3) and baytrail to lpc_ich
- Add new drivers for tps65218, rtsx_usb, bcm590xx
(Re-)moved drivers:
- twl4030 ==> drivers/iio
- ti-ssp ==> /dev/null"
* tag 'mfd-for-linus-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (103 commits)
mfd: wm5110: Correct default for HEADPHONE_DETECT_1
mfd: arizona: Correct small errors in the DT binding documentation
mfd: arizona: Mark DSP clocking register as volatile
mfd: devicetree: bindings: Add pm8xxx RTC description
mfd: kempld-core: Fix potential hang-up during boot
mfd: sec-core: Fix uninitialized 'regmap_rtc' on S2MPA01
mfd: tps65910: Fix regmap_irq_chip_data leak on mfd_add_devices fail
mfd: tps65910: Fix possible invalid pointer dereference on regmap_add_irq_chip fail
mfd: sec-core: Fix I2C dummy device resource leak on probe failure
mfd: sec-core: Add of_compatible strings for clock MFD cells
mfd: Remove obsolete ti-ssp driver
Documentation: mfd: s2mps11: Describe S5M8767 and S2MPS14 clocks
mfd: bcm590xx: Fix type argument for module device table
mfd: lpc_ich: Add support for Intel Bay Trail SoC
mfd: lpc_ich: Add support for NM10 GPIO
mfd: lpc_ich: Change Avoton to iTCO v3
watchdog: iTCO_wdt: Add support for v3 silicon
mfd: lpc_ich: Add support for iTCO v3
mfd: lpc_ich: Remove lpc_ich_cfg struct use
mfd: lpc_ich: Only configure watchdog or GPIO when present
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
- substantial cleanup of the generic and transport layers, in the
direction of an ultimate goal of making struct hid_device completely
transport independent, by Benjamin Tissoires
- cp2112 driver from David Barksdale
- a lot of fixes and new hardware support (Dualshock 4) to hid-sony
driver, by Frank Praznik
- support for Win 8.1 multitouch protocol by Andrew Duggan
- other smaller fixes / device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (75 commits)
HID: sony: fix force feedback mismerge
HID: sony: Set the quriks flag for Bluetooth controllers
HID: sony: Fix Sixaxis cable state detection
HID: uhid: Add UHID_CREATE2 + UHID_INPUT2
HID: hyperv: fix _raw_request() prototype
HID: hyperv: Implement a stub raw_request() entry point
HID: hid-sensor-hub: fix sleeping function called from invalid context
HID: multitouch: add support for Win 8.1 multitouch touchpads
HID: remove hid_output_raw_report transport implementations
HID: sony: do not rely on hid_output_raw_report
HID: cp2112: remove the last hid_output_raw_report() call
HID: cp2112: remove various hid_out_raw_report calls
HID: multitouch: add support of other generic collections in hid-mt
HID: multitouch: remove pen special handling
HID: multitouch: remove registered devices with default behavior
HID: hidp: Add a comment that some devices depend on the current behavior of uniq
HID: sony: Prevent duplicate controller connections.
HID: sony: Perform a boundry check on the sixaxis battery level index.
HID: sony: Fix work queue issues
HID: sony: Fix multi-line comment styling
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the huge drivers/staging/ update for 3.15-rc1.
Loads of cleanup fixes, a few drivers removed, and some new ones
added.
All have been in linux-next for a while"
* tag 'staging-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1375 commits)
staging: xillybus: XILLYBUS_PCIE depends on PCI_MSI
staging: xillybus: Added "select CRC32" for XILLYBUS in Kconfig
staging: comedi: poc: remove obsolete driver
staging: unisys: replace kzalloc/kfree with UISMALLOC/UISFREE
staging: octeon-usb: prevent memory corruption
staging: usbip: fix line over 80 characters
staging: usbip: fix quoted string split across lines
Staging: unisys: Remove RETINT macro
Staging: unisys: Remove FAIL macro
Staging: unisys: Remove RETVOID macro
Staging: unisys: Remove RETPTR macro
Staging: unisys: Remove RETBOOL macro
Staging: unisys: Remove FAIL_WPOSTCODE_1 macro
Staging: unisys: Cleanup macros to get rid of goto statements
Staging: unisys: include: Remove unused macros from timskmod.h
staging: dgap: fix the rest of the checkpatch warnings in dgap.c
Staging: bcm: Remove unnecessary parentheses
staging: wlags49_h2: Delete unnecessary braces
staging: wlags49_h2: Do not use assignment in if condition
staging: wlags49_h2: Enclose macro in a do-while loop
...
|
|
During probe the driver allocates dummy I2C devices (i2c_new_dummy())
but they aren't unregistered during driver remove or probe failure.
Additionally driver does not check the return value of i2c_new_dummy().
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later
dereferenced by i2c_smbus_{read,write}_data() functions.
Fix issues by properly checking for i2c_new_dummy() return value and
unregistering I2C devices on driver remove or probe failure.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Beomho Seo <beomho.seo@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Ensure that querying the IIO buffer scan_mask returns a value of
0 or 1. Currently querying the scan mask has the value returned
by test_bit(), which returns either true or false. For some
architectures test_bit() may return -1 for true, which will appear
to return an error when returning from iio_scan_mask_query().
Additionally, it's important for the sysfs interface to consistently
return the same thing when querying the scan_mask.
Signed-off-by: Alec Berg <alecaberg@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is a driver for an A/D converter, which belongs into
drivers/iio/adc.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
When sample_hold_time is zero (this is the case when DT is not used or if
atmel,adc-sample-hold-time is omitted), then the calculated shtim is large.
Make that 0, which is the default for that register and the ADC will then use a
sane value of 2/ADCCLK or 1/ADCCLK depending on the version.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
In read integration time function, assign 0 to val.
Because, prevent return inaccurate value when call read integration time.
Cc: Stable@vger.kernel.org
Cc: Kevin Tsai <ktsai@capellamicro.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
men_z188_adc needs to include linux/io.h. This fixes a build error
discovered by 0-day buid bot
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third IIO new drivers and cleanups series for 3.15.
New driver
* Xilinx XADC driver - This has been ready for a while but was awaiting
a device tree ack (or as it turns out 3+ weeks).
Cleanup
* Drop some unreachable code from mag3110 highlighted by smatch.
Fix
* vf610 - introduced this cycle - put a possible negative error code
into an unsigned long. Another smatch find - this one promoted by
guilt that Dan was busy fixing all our messups.
|
|
Trying to use the at91_adc driver while not using device tree is ending up in a
kernel crash:
Unable to handle kernel NULL pointer dereference at virtual address 00000004
[...]
[<c01f3510>] (at91_adc_probe) from [<c0183828>] (platform_drv_probe+0x18/0x48)
[<c0183828>] (platform_drv_probe) from [<c01824a4>] (driver_probe_device+0x100/0x218)
[<c01824a4>] (driver_probe_device) from [<c0182648>] (__driver_attach+0x8c/0x90)
[<c0182648>] (__driver_attach) from [<c0180de4>] (bus_for_each_dev+0x58/0x88)
[<c0180de4>] (bus_for_each_dev) from [<c0181c7c>] (bus_add_driver+0xd4/0x1d4)
[<c0181c7c>] (bus_add_driver) from [<c0182c40>] (driver_register+0x78/0xf4)
[<c0182c40>] (driver_register) from [<c0008998>] (do_one_initcall+0xe8/0x14c)
[<c0008998>] (do_one_initcall) from [<c02f0b50>] (kernel_init_freeable+0xec/0x1b4)
[<c02f0b50>] (kernel_init_freeable) from [<c022acdc>] (kernel_init+0x8/0xe4)
[<c022acdc>] (kernel_init) from [<c0009670>] (ret_from_fork+0x14/0x24)
This is because the at91_adc_caps structure is mandatory but is not filled when
using platform_data. Correct that by using an id_table. It ensues that the
driver will not match "at91_adc" anymore but it was crashing anyway.
Fixes: c46016665fff (iio: at91: ADC start-up time calculation changed since at91sam9x5)
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
We want those fixes in here
|
|
We want these fixes in here as well.
|
|
Issue highlighted by smatch warning:
CHECK drivers/iio/adc/vf610_adc.c
drivers/iio/adc/vf610_adc.c:466 vf610_read_raw() warn: unsigned 'ret' is never less than zero.
As wait_for_completion_interruptible_timeout can return -ERESTARTSTSYS, if
interrupted, ret must be signed.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Fugang Duan <B38611@freescale.com>
|
|
The Xilinx XADC is a ADC that can be found in the series 7 FPGAs from Xilinx.
The XADC has a DRP interface for communication. Currently two different
frontends for the DRP interface exist. One that is only available on the ZYNQ
family as a hardmacro in the SoC portion of the ZYNQ. The other one is available
on all series 7 platforms and is a softmacro with a AXI interface. This driver
supports both interfaces and internally has a small abstraction layer that hides
the specifics of these interfaces from the main driver logic.
The ADC has a couple of internal channels which are used for voltage and
temperature monitoring of the FPGA as well as one primary and up to 16 channels
auxiliary channels for measuring external voltages. The external auxiliary
channels can either be directly connected each to one physical pin on the FPGA
or they can make use of an external multiplexer which is responsible for
multiplexing the external signals onto one pair of physical pins.
The voltage and temperature monitoring channels also have an event capability
which allows to generate a interrupt when their value falls below or raises
above a set threshold.
Buffered sampling mode is supported by the driver, but only for AXI-XADC since
the ZYNQ XADC interface does not have capabilities for supporting buffer mode
(no end-of-conversion interrupt). If buffered mode is supported the driver will
register two triggers. One "xadc-samplerate" trigger which will generate samples
with the configured samplerate. And one "xadc-convst" trigger which will
generate one sample each time the CONVST (conversion start) signal is asserted.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add support for MEN 16z188 ADC IP Core on MCB FPGAs.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
drivers/iio/magnetometer/mag3110.c:197 mag3110_read_raw()
info: ignoring unreachable code.
drivers/iio/magnetometer/mag3110.c
185 case IIO_CHAN_INFO_SCALE:
186 switch (chan->type) {
187 case IIO_MAGN:
188 *val = 0;
189 *val2 = 1000;
190 return IIO_VAL_INT_PLUS_MICRO;
191 case IIO_TEMP:
192 *val = 1000;
193 return IIO_VAL_INT;
194 default:
195 return -EINVAL;
196 }
197 return IIO_VAL_INT_PLUS_MICRO;
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
introduced by f9279d3a, mag3110: Scale factor missing
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The event code currently holds a spinlock with IRQs disabled while calling
kfifo_to_user(). kfifo_to_user() can generate a page fault though, which means
we have to be able to sleep, which is not possible if the interrupts are
disabled. The good thing is that kfifo handles concurrent read and write access
just fine as long as there is only one reader and one writer, so we do not any
locking to protect against concurrent access from the read and writer thread. It
is possible though that userspace is trying to read from the event FIFO from
multiple concurrent threads, so we need to add locking to protect against this.
This is done using a mutex. The mutex will only protect the kfifo_to_user()
call, it will not protect the waitqueue. This means that multiple threads can be
waiting for new data and once a new event is added to the FIFO all waiting
threads will be woken up. If one of those threads is unable to read any data
(because another thread already read all the data) it will go back to sleep. The
only remaining issue is that now that the clearing of the BUSY flag and the
emptying of the FIFO does no longer happen in one atomic step it is possible
that a event is added to the FIFO after it has been emptied and this sample will
be visible the next time a new event file descriptor is created. To avoid this
rather move the emptying of the FIFO from iio_event_chrdev_release to
iio_event_getfd().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch adds support for the new barometer sensor: LPS25H.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Added usage id processing for Pressure Sensor. This uses IIO
interfaces for triggered buffer to present data to user
mode. This uses HID sensor framework for registering callback
events from the sensor hub.
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Added usage id processing for Proximity (Human Presence).
This uses IIO interfaces for triggered buffer to present data
to user mode. This uses HID sensor framework for registering
callback events from the sensor hub.
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
name_format already contains the final name and no format characters. So the
code basically reads:
dev_attr->attr.name = kstrdup(GFP_KERNEL, name_format);
if (dev_attr->attr.name == NULL)
...
kfree(name_format);
Which means we can save one alloc and free pair per attribute name if we
directly assign name_format to dev_attr->attr.name.
The patch also renames name_format to name to denote that this is indeed the
final name and has no format characters in it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The extended name is channel specific and should not be included in shared
attributes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The driver was not able to manage the sensor: during probe function
and wai check, the driver stops and writes: "device name and WhoAmI mismatch."
The correct value of L3GD20H wai is 0xd7 instead of 0xd4.
Dropped support for the sensor.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Integration time of cm32181 is guessed about milliseconds.
But cm32181_read_als_it function return IIO_VAL_INT.
So fixed to return IIO_VAL_INT_PLUS_MICRO.
Next, add .write_raw_get_fmt callback function for call iio_str_to_fixpoint.
v2: cm32181_write_als_id function fixed as it was.
Cc: Kevin Tsai <ktsai@capellamicro.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch is fixed [read/write] integration time function.
cm36651 have integration time from 1 to 640 milliseconds.
But, print more then the thousand second. when call *_integration_time attribute.
Because read_integration_time function return IIO_VAL_INT.
read integration time function is changed return IIO_VAL_INT_PLUS_MICRO;
And then .write_raw_get_fmt callback function for parse a fixed-point number from a string.
Some description is revised milliseconds unit.
v2: cm36651_write_int_time function fixed as it was.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Get rid of obsolete uses of goto error_ret and some empty lines.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch fixes some typos in max1363_chip_info_tbl[].
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Remove the hard coded indexes, instead search for usage id and
use the index to set the power and report state.
This will fix issue, where the report descriptor doesn't contain
the full list of possible selector for power and report state.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
the property is not per-channel, but shared by type
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Kravchenko Oleksandr <x0199363@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add Freescale Vybrid vf610 adc driver. The driver only support
ADC software trigger.
VF610 ADC device documentation is available at below reference manual
(chapter 37):
http://cache.freescale.com/files/32bit/doc/ref_manual/VYBRIDRM.pdf?
fpsp=1&WT_TYPE=Reference%20Manuals&WT_VENDOR=FREESCALE&WT_FILE_FORMAT
=pdf&WT_ASSET=Documentation
CC: Shawn Guo <shawn.guo@linaro.org>
CC: Jonathan Cameron <jic23@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: Peter Meerwald <pmeerw@pmeerw.net>
CC: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
temperature is reported in milli-Celsius
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new drivers and cleanups for IIO in the 3.15 cycle.
New drivers:
* si7005 relative humidity and temperature sensor
* Lite-on ltr501 ambient light and proximity sensor
Cleanups
* Clean up some dead comments in max1363
* Drop some obsolete variables in adjd_s311 and tcs3472 left over from
the introduction of iio_push_to_buffers_with_timestamp.
* Drop some unneeded linux/init.h includes
* Squish a sparse warning in mpl3115 by correctly specifying a be32 variable.
* A number of cleanups and fixes for sca3000
* Drop an unneed checks in mxs-lradc, ad7303 and adis16400.
* Drop a platform_set_drvdata in viperboard after the only use of it was
removed during a devm conversion.
* Add a missing device name for ak8975 to comply with the ABI.
* Put mpu6050 into the IMU menu as it slipped out into the main menu.
* Fix a typo and some comment formatting in mpu6050.
* Document at91 ADC clock properties.
|
|
Signed-off-by: Manuel Stahl <manuel.stahl@iis.fraunhofer.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Signed-off-by: Manuel Stahl <manuel.stahl@iis.fraunhofer.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
In kernel version 3.13, devm_regulator_get() may return no error
if a regulator is undeclared. regulator_get_voltage() will return
-EINVAL if this happens. This causes the driver to fail loading if
the vref regulator is not declared.
Since vref is optional, call devm_regulator_get_optional instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This driver was not complying with the ABI and the purpose of this patch
is to bring it inline so that userspace will correctly identify the channels.
Should use channel modifiers (X/Y/Z), not channel indices
timestamp channel has scan index 3, not 4
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Kravchenko Oleksandr <x0199363@ti.com>
Cc: Stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This is necessary since timestamp is calculated as the last element
in iio_compute_scan_bytes().
Without this fix any userspace code reading the layout of the buffer via
sysfs will incorrectly interpret the data leading some nasty corruption.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch add device name.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This effects the reported scale of the raw values, and thus userspace
applications that use this value.
One micro tesla equal 0.01 gauss. So I have fixed calculation formula And add RAW_TO_GAUSS macro.
ASA is in the range of 0 to 255. If multiply 0.003, calculation result(in_magn_[*]_scale) is
always 0. So multiply 3000 and return and IIO_VAL_INT_PLUS_MICRO.
As a result, read_raw call back function return accurate scale value.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
need to print leading zeros, hence "%d.%06d"
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
buffer is enabled
individual reads are not permitted concurrently with buffered reads
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 3.14 cycle.
Included is the patch previously set as the fourth round for 3.13 which was
to late to be appropriate.
* Another endian fix (ad799x adc) due to missuse of the IIO_ST macro (which
is going away very shortly)
* A reversed error check in ad5933 which will make the probe fail.
* A buffer overflow in the example code in the documentation.
* ad799x was freeing an irq that might or might not have been requested.
* tsl2563 was checking the wrong element of chan_spec for modifiers. Thus some
sysfs reads would give the wrong values.
* A missing dependency on HAS_IOMEM in spear_adc and lpc32xx was causing some
test build failures (on s390 and perhaps elsewhere).
I also have a few fixes queued up for things that went in during the 3.14
merge window which will follow as a separate pull request (to avoid rebasing
my tree).
|
|
"ret" is zero here. There is no need to check again.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
We know "ret" is zero here so there is no need to check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
