| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes in the 4.12 cycle.
Matt finally set up the lightning storm he needed to test the as3935.
* core
- Fix a null pointer deference in iio_trigger_write_current when changing
from a non existent trigger to another non existent trigger.
* a3935
- Recalibrate the RCO after resume.
- Fix interrupt mask so that we actually get some interrupts.
- Use iio_trigger_poll_chained as we aren't in interrupt context.
* am335x
- Fix wrong allocation size provided for private data to iio_device_alloc.
* bcm_iproc
- Swapped primary and secondary isr handlers.
* ltr501
- Fix swapped als/ps register fields when enabling interrupts
* max9611
- Wrong scale factor for the shunt_resistor attribute.
* sun4-gpadc
- Module autoloading fixes by adding the device table declarations.
- Fix parent device being used in devm functions.
|
|
For the sake of DT binding stability, this IIO driver is a child of an
MFD driver for Allwinner A10, A13 and A31 because there already exists a
DT binding for this IP. The MFD driver has a DT node but the IIO driver
does not.
The IIO device registers the temperature sensor in the thermal framework
using the DT node of the parent, the MFD device, so the thermal
framework could match the phandle to the MFD device in the DT and the
struct device used to register in the thermal framework.
devm_thermal_zone_of_sensor_register was previously used to register the
thermal sensor with the parent struct device of the IIO device,
representing the MFD device. By doing so, we registered actually the
parent in the devm routine and not the actual IIO device.
This lead to the devm unregister function not being called when the IIO
module driver is removed. It resulted in the thermal framework still
polling the get_temp function of the IIO module while the device doesn't
exist anymore, thus generated a kernel panic.
Use the non-devm function instead and do the unregister manually in the
remove function.
Fixes: d1caa9905538 ("iio: adc: add support for Allwinner SoCs ADC")
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This is an upstream port of an IIO driver for the TI ADC108S102 and
ADC128S102. The former can be found on the Intel Galileo Gen2 and the
Siemens SIMATIC IOT2000. For those boards, ACPI-based enumeration is
included.
Due to the lack of regulators under ACPI, we hard-code the voltage
provided to the VA pin of the ADC to 5 V, the value used on Galileo and
IOT2000. For DT usage, the regulator "vref-supply" provides this
information. Note that DT usage has not been tested.
Original author: Bogdan Pricop <bogdan.pricop@emutex.com>
Ported from Intel Galileo Gen2 BSP to Intel Yocto kernel:
Todor Minchev <todor@minchev.co.uk>.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Get rid of #ifdef CONFIG_PM by adding __maybe_unused macro to
st_lsm6dsx_suspend and st_lsm6dsx_resume function declarations
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Some x86 tablets use the BMA250E accelerometer, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The BMA250E adds a new fifo mode and is fully backwards compatible
with the BMA250, but with a different chip-id.
This commit adds support for it by adjusting the chip-id check and
otherwise treating it as a regular BMA250.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Move proximity channel from last to first in structs to avoid confusion
later with buffered triggers. Proximity data output is first in rpr0521
register map.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add sysfs read/write proximity offset feature. Offset is read/write from
sensor registers. Values are proximity raw 10-bit values. After applying
offset value, output values will be (measured_raw - offset_value). Output
values are unsigned so offset value doesn't make output negative.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add sysfs read/write sample frequency.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Just whitespace change, no functional changes.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Changed magic number to sizeof() on value read.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Refactor _set_power_state(), _resume() and _suspend().
Enable measurement only when needed, not in _init(). System can suspend
during measurement and measurement is continued on resume.
Pm turns off measurement when both ps and als measurements are disabled for
2 seconds. During off-time the power save is 20-500mA, typically 180mA.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Set sensor measurement off after probe fail in pm_runtime_set_active() or
iio_device_register(). Without this change sensor measurement stays on
even though probe fails on these calls.
This is maybe rare case, but causes constant power drain without any
benefits when it happens. Power drain is 20-500uA, typically 180uA.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Sensor was marked enabled on each call even if the call was for disabling
sensor.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The register mapping for the IIO driver for the Liteon Light and Proximity
sensor LTR501 interrupt mode is interchanged (ALS/PS).
There is a register called INTERRUPT register (address 0x8F)
Bit 0 represents PS measurement trigger.
Bit 1 represents ALS measurement trigger.
This two bit fields are interchanged within the driver.
see datasheet page 24:
http://optoelectronics.liteon.com/upload/download/DS86-2012-0006/S_110_LTR-501ALS-01_PrelimDS_ver1%5B1%5D.pdf
Signed-off-by: Franziska Naepelt <franziska.naepelt@idt.com>
Fixes: 7ac702b3144b6 ("iio: ltr501: Add interrupt support")
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The third argument of devm_request_threaded_irq() is the primary
handler. It is called in hardirq context and checks whether the
interrupt is relevant to the device. If the primary handler returns
IRQ_WAKE_THREAD, the secondary handler (a.k.a. handler thread) is
scheduled to run in process context.
bcm_iproc_adc.c uses the secondary handler as the primary one
and the other way around. So this patch fixes the same, along with
re-naming the secondary handler and primary handler names properly.
Tested on the BCM9583XX iProc SoC based boards.
Fixes: 4324c97ecedc ("iio: Add driver for Broadcom iproc-static-adc")
Reported-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
In case oldtrig == trig == NULL (which happens when we set none
trigger, when there is already none set) there is a NULL pointer
dereference during iio_trigger_put(trig). Below is kernel output when
this occurs:
[ 26.741790] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 26.750179] pgd = cacc0000
[ 26.752936] [00000000] *pgd=8adc6835, *pte=00000000, *ppte=00000000
[ 26.759531] Internal error: Oops: 17 [#1] SMP ARM
[ 26.764261] Modules linked in: usb_f_ncm u_ether usb_f_acm u_serial usb_f_fs libcomposite configfs evbug
[ 26.773844] CPU: 0 PID: 152 Comm: synchro Not tainted 4.12.0-rc1 #2
[ 26.780128] Hardware name: Freescale i.MX6 Ultralite (Device Tree)
[ 26.786329] task: cb1de200 task.stack: cac92000
[ 26.790892] PC is at iio_trigger_write_current+0x188/0x1f4
[ 26.796403] LR is at lock_release+0xf8/0x20c
[ 26.800696] pc : [<c0736f34>] lr : [<c016efb0>] psr: 600d0013
[ 26.800696] sp : cac93e30 ip : cac93db0 fp : cac93e5c
[ 26.812193] r10: c0e64fe8 r9 : 00000000 r8 : 00000001
[ 26.817436] r7 : cb190810 r6 : 00000010 r5 : 00000001 r4 : 00000000
[ 26.823982] r3 : 00000000 r2 : 00000000 r1 : cb1de200 r0 : 00000000
[ 26.830528] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 26.837683] Control: 10c5387d Table: 8acc006a DAC: 00000051
[ 26.843448] Process synchro (pid: 152, stack limit = 0xcac92210)
[ 26.849475] Stack: (0xcac93e30 to 0xcac94000)
[ 26.853857] 3e20: 00000001 c0736dac c054033c cae6b680
[ 26.862060] 3e40: cae6b680 00000000 00000001 cb3f8610 cac93e74 cac93e60 c054035c c0736db8
[ 26.870264] 3e60: 00000001 c054033c cac93e94 cac93e78 c029bf34 c0540348 00000000 00000000
[ 26.878469] 3e80: cb3f8600 cae6b680 cac93ed4 cac93e98 c029b320 c029bef0 00000000 00000000
[ 26.886672] 3ea0: 00000000 cac93f78 cb2d41fc caed3280 c029b214 cac93f78 00000001 000e20f8
[ 26.894874] 3ec0: 00000001 00000000 cac93f44 cac93ed8 c0221dcc c029b220 c0e1ca39 cb2d41fc
[ 26.903079] 3ee0: cac93f04 cac93ef0 c0183ef0 c0183ab0 cb2d41fc 00000000 cac93f44 cac93f08
[ 26.911282] 3f00: c0225eec c0183ebc 00000001 00000000 c0223728 00000000 c0245454 00000001
[ 26.919485] 3f20: 00000001 caed3280 000e20f8 cac93f78 000e20f8 00000001 cac93f74 cac93f48
[ 26.927690] 3f40: c0223680 c0221da4 c0246520 c0245460 caed3283 caed3280 00000000 00000000
[ 26.935893] 3f60: 000e20f8 00000001 cac93fa4 cac93f78 c0224520 c02235e4 00000000 00000000
[ 26.944096] 3f80: 00000001 000e20f8 00000001 00000004 c0107f84 cac92000 00000000 cac93fa8
[ 26.952299] 3fa0: c0107de0 c02244e8 00000001 000e20f8 0000000e 000e20f8 00000001 fbad2484
[ 26.960502] 3fc0: 00000001 000e20f8 00000001 00000004 beb6b698 00064260 0006421c beb6b4b4
[ 26.968705] 3fe0: 00000000 beb6b450 b6f219a0 b6e2f268 800d0010 0000000e cac93ff4 cac93ffc
[ 26.976896] Backtrace:
[ 26.979388] [<c0736dac>] (iio_trigger_write_current) from [<c054035c>] (dev_attr_store+0x20/0x2c)
[ 26.988289] r10:cb3f8610 r9:00000001 r8:00000000 r7:cae6b680 r6:cae6b680 r5:c054033c
[ 26.996138] r4:c0736dac r3:00000001
[ 26.999747] [<c054033c>] (dev_attr_store) from [<c029bf34>] (sysfs_kf_write+0x50/0x54)
[ 27.007686] r5:c054033c r4:00000001
[ 27.011290] [<c029bee4>] (sysfs_kf_write) from [<c029b320>] (kernfs_fop_write+0x10c/0x224)
[ 27.019579] r7:cae6b680 r6:cb3f8600 r5:00000000 r4:00000000
[ 27.025271] [<c029b214>] (kernfs_fop_write) from [<c0221dcc>] (__vfs_write+0x34/0x120)
[ 27.033214] r10:00000000 r9:00000001 r8:000e20f8 r7:00000001 r6:cac93f78 r5:c029b214
[ 27.041059] r4:caed3280
[ 27.043622] [<c0221d98>] (__vfs_write) from [<c0223680>] (vfs_write+0xa8/0x170)
[ 27.050959] r9:00000001 r8:000e20f8 r7:cac93f78 r6:000e20f8 r5:caed3280 r4:00000001
[ 27.058731] [<c02235d8>] (vfs_write) from [<c0224520>] (SyS_write+0x44/0x98)
[ 27.065806] r9:00000001 r8:000e20f8 r7:00000000 r6:00000000 r5:caed3280 r4:caed3283
[ 27.073582] [<c02244dc>] (SyS_write) from [<c0107de0>] (ret_fast_syscall+0x0/0x1c)
[ 27.081179] r9:cac92000 r8:c0107f84 r7:00000004 r6:00000001 r5:000e20f8 r4:00000001
[ 27.088947] Code: 1a000009 e1a04009 e3a06010 e1a05008 (e5943000)
[ 27.095244] ---[ end trace 06d1dab86d6e6bab ]---
To fix that problem call iio_trigger_put(trig) only when trig is not
NULL.
Fixes: d5d24bcc0a10 ("iio: trigger: close race condition in acquiring trigger reference")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Reset GPIO is active low.
Currently driver uses gpiod_set_value(1) to clean reset, which depends
on device tree to contain GPIO_ACTIVE_HIGH - that does not match reality.
This fixes driver to use _raw version of gpiod_set_value() to enforce
active-low semantics despite of what's written in device tree. Allowing
device tree to override that only opens possibility for errors and does
not add any value.
Additionally, use _cansleep version to make things work with i2c-gpio
and other sleeping gpio drivers.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Possible values of sensing_mode are encoded with strings and actual
strings used are not obvious.
Provide a hint by enabling in_voltage_sensing_mode_available attribute.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Currently, driver generates events for channels if new reading differs
from previous one. This "previous value" is initialized to zero, which
results into event if value is constant-one.
Fix that by initializing "previous value" by reading at event enable
time.
This provides reliable sequence for userspace:
- enable event,
- AFTER THAT read current value,
- AFTER THAT each event will correspond to change.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
With current event-only driver, it is not possible for user space
application to know current senses if they don't change since
application starts.
Address that by adding raw access to channels.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This fixes the following warning when building with clang:
drivers/iio/light/isl29018.c:808:36: error: variable
'isl29018_acpi_match' is not needed and will not be emitted
[-Werror,-Wunneeded-internal-declaration]
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
HID sensor hubs using Integrated Senor Hub (ISH) has added capability to
support batch mode. This allows host processor to go to sleep for extended
duration, while the sensor hub is storing samples in its internal buffers.
'Commit f4f4673b7535 ("iio: add support for hardware fifo")' implements
feature in IIO core to implement such feature. This feature is used in
bmc150-accel-core.c to implement batch mode. This implementation allows
software device buffer watermark to be used as a hint to adjust hardware
FIFO.
But HID sensor hubs don't allow to change internal buffer size of FIFOs.
Instead an additional usage id to set "maximum report latency" is defined.
This allows host to go to sleep upto this latency period without getting
any report. Since there is no ABI to set this latency, a new attribute
"hwfifo_timeout" is added so that user mode can specify a latency.
This change checks presence of usage id to get/set maximum report latency
and if present, it will expose hwfifo_timeout.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch adds runtime power management support to the tsl2583 driver.
The device is powered off after two seconds of inactivity. Verified that
the driver still functions correctly using a TSL2581 hooked up to a
Raspberry Pi 2.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add system sleep power management support to hts221 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The power and current "shunt-resistor" attribute's 'show' function
displays the resistor value in milli-Ohms, while the ABI description
specifies it should be displayed in Ohms. Fix it.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This adds support for the Texas Instruments ADC084S021 ADC chip.
Signed-off-by: Mårten Lindahl <martenli@axis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
We should be allocating enough information for a tiadc_device struct
which is about 400 bytes but instead we allocate enough for a second
iio_dev struct which is over 2000 bytes.
Fixes: fea89e2dfcea ("iio: adc: ti_am335x_adc: use variable names for sizeof() operator")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The Linear Technology LTC2631, LTC2633 and LTC2635 are very similar
to the AD5064 device, in particular the LTC2627.
This patch adds support for those devices. Only the LTC2633 has been
tested, which is the 2-channel variant. The LTC2631 is the 1-channel,
and the LTC2635 the 4-channel version. The actual DAC resolution depends
on the exact chip type and can be 12, 10 or 8 bits, using the upper bits
so this has no effect on the register map. The internal reference is set
to 2.5V on "L" versions, and it's 4.096V for "H" versions.
Datasheets:
LTC2631: http://www.linear.com/docs/26553
LTC2633: http://www.linear.com/docs/39529
LTC2635: http://www.linear.com/docs/28754
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
If the timeout-case prints a warning message then probably the interrupted
case should also. Further, wait_for_completion_interruptible_timeout()
returns long not int.
Fixes: commit 03b262f2bbf4 ("iio:pressure: initial zpa2326 barometer support")
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
|
|
Add support for TRGO2 trigger that can be found on STM32F7.
Add additional master modes supported by TRGO2.
Register additional "tim[1/8]_trgo2" triggers for timer1 & timer8.
Detect TRGO2 timer capability (master mode selection 2).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
If the driver is built as a module, it won't be autloaded if the devices
are registered via OF code because the OF device table
entries are not exported as aliases
Before the patch:
$ modinfo drivers/iio/adc/sun4i-gpadc-iio.ko | grep alias
alias: platform:sun6i-a31-gpadc-iio
alias: platform:sun5i-a13-gpadc-iio
alias: platform:sun4i-a10-gpadc-iio
After the patch:
$ modinfo drivers/iio/adc/sun4i-gpadc-iio.ko | grep alias
alias: of:N*T*Callwinner,sun8i-a33-thsC*
alias: of:N*T*Callwinner,sun8i-a33-ths
alias: platform:sun6i-a31-gpadc-iio
alias: platform:sun5i-a13-gpadc-iio
alias: platform:sun4i-a10-gpadc-iio
Signed-off-by: Eduardo Molinas <edu.molinas@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
registered
If the driver is built as a module, it won't be autloaded if the devices
are registered via PLATFORM code because the PLATFORM device table
entries are not exported as aliases
Before the patch:
$ modinfo drivers/iio/adc/sun4i-gpadc-iio.ko | grep alias
$
After the patch:
$ modinfo drivers/iio/adc/sun4i-gpadc-iio.ko | grep alias
alias: platform:sun6i-a31-gpadc-iio
alias: platform:sun5i-a13-gpadc-iio
alias: platform:sun4i-a10-gpadc-iio
Signed-off-by: Eduardo Molinas <edu.molinas@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Commit 7906dd52c5a0 ("iio: ina2xx: Fix whitespace and re-order code")
changed the register number of the MASK_ENABLE register from 0x06 to the
value equivalent GENMASK(2,1), although its no mask.
Also fix a typo (INA2_6_6 instead of INA2_2_6), and use the datasheet
name ("Mask/Enable") for the register number define.
Fix bad indentation for channel attributes.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Drop static on a local variable, when the variable is initialized before
use, on every possible execution path through the function. The static has
no benefit, and dropping it reduces the code size.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
The change in code size is indicates by the following output from the size
command.
before:
text data bss dec hex filename
3879 512 8 4399 112f drivers/iio/accel/hid-sensor-accel-3d.o
after:
text data bss dec hex filename
3863 512 0 4375 1117 drivers/iio/accel/hid-sensor-accel-3d.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Using iio_trigger_poll() can oops when multiple interrupts
happen before the first is handled.
Use iio_trigger_poll_chained() instead and use the timestamp
when processed, since it will be in theory be 2 ms max latency.
Fixes: 24ddb0e4bba4 ("iio: Add AS3935 lightning sensor support")
Cc: stable@vger.kernel.org
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
MAX31856 is register equivalent to the MAX31855 but suppports J, N, R,
S, T, E and B type thermocouples in addition to K-type.
Data conversion for the various types happens transparently to the driver
via probe type detection, and a LUT on the sensor.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Meson GX SoCs however use some magic bits to prevent simultaneous (=
conflicting, because only consumer should use the FIFO buffer with the
ADC results) usage by the Linux kernel and the bootloader (the BL30
bootloader uses the SAR ADC to read the CPU temperature).
This patch changes guards all BL30 functionality so it is skipped on
SoCs which don't have it. Since the hardware itself doesn't know whether
BL30 is available the internal meson_sar_adc_data is extended so this
information can be provided per of_device_id.data inside the driver.
Additionally the clocks "adc_clk" and "adc_sel" are not provided by the
clock-controller itself. "adc_sel" is not available at all. "adc_clk"
is provided by the SAR ADC IP block itself on Meson8b (and earlier).
This is already supported by the meson_saradc driver.
Finally this introduces new of_device_ids for the Meson8 and Meson8b
SoCs so the driver can be wired up in the corresponding DT.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
These are only passed as of_device_id.data and never modified. Thus we
can mark them as static const, just like the of_device_id instances
where they are used.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add orientation sensor "scale" and "offset" parse support.
These two properties are needed for exponent data conversion.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Xu Even <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Geomagnetic orientation(AM) sensor is one kind of orientation 6dof sensor.
It gives the device rotation in respect to the earth center and the
magnetic north. The sensor is implemented through use of an accelerometer
and magnetometer do not use gyroscope. It is a standard HID sensor.
More information can be found in:
http://www.usb.org/developers/hidpage/HUTRR59_-_Usages_for_Wearables.pdf
Geomagnetic orientation(AM) sensor and dev rotation sensor have same
channel and share channel usage id. So the most of the code for relative
orientation sensor can be reused.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Relative orientation(AG) sensor is a 6dof orientation sensor,
it depends on acceleration and gyroscope sensor data. It gives
a quaternion describing the orientation of the device relative
to an initial orientation. It is a standard HID sensor.
More information can be found in:
http://www.usb.org/developers/hidpage/HUTRR59_-_Usages_for_Wearables.pdf
Relative orientation(AG) sensor and dev rotation sensor have same
channels and share channel usage id. So the most of the code for
relative orientation sensor can be reused.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Xu Even <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO updates from Greg KH:
"Here is the big staging tree update for 4.12-rc1.
It's a big one, adding about 350k new lines of crap^Wcode, mostly all
in a big dump of media drivers from Intel. But there's other new
drivers in here as well, yet-another-wifi driver, new IIO drivers, and
a new crypto accelerator.
We also deleted a bunch of stuff, mostly in patch cleanups, but also
the Android ION code has shrunk a lot, and the Android low memory
killer driver was finally deleted, much to the celebration of the -mm
developers.
All of these have been in linux-next with a few build issues that will
show up when you merge to your tree"
Merge conflicts in the new rtl8723bs driver (due to the wifi changes
this merge window) handled as per linux-next, courtesy of Stephen
Rothwell.
* tag 'staging-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1182 commits)
staging: fsl-mc/dpio: add cpu <--> LE conversion for dpaa2_fd
staging: ks7010: remove line continuations in quoted strings
staging: vt6656: use tabs instead of spaces
staging: android: ion: Fix unnecessary initialization of static variable
staging: media: atomisp: fix range checking on clk_num
staging: media: atomisp: fix misspelled word in comment
staging: media: atomisp: kmap() can't fail
staging: atomisp: remove #ifdef for runtime PM functions
staging: atomisp: satm include directory is gone
atomisp: remove some more unused files
atomisp: remove hmm_load/store/clear indirections
atomisp: kill off mmgr_free
atomisp: clean up the hmm init/cleanup indirections
atomisp: handle allocation calls before init in the hmm layer
staging: fsl-dpaa2/eth: Add maintainer for Ethernet driver
staging: fsl-dpaa2/eth: Add TODO file
staging: fsl-dpaa2/eth: Add trace points
staging: fsl-dpaa2/eth: Add driver specific stats
staging: fsl-dpaa2/eth: Add ethtool support
staging: fsl-dpaa2/eth: Add Freescale DPAA2 Ethernet driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of new char/misc driver drivers and features for
4.12-rc1.
There's lots of new drivers added this time around, new firmware
drivers from Google, more auxdisplay drivers, extcon drivers, fpga
drivers, and a bunch of other driver updates. Nothing major, except if
you happen to have the hardware for these drivers, and then you will
be happy :)
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (136 commits)
firmware: google memconsole: Fix return value check in platform_memconsole_init()
firmware: Google VPD: Fix return value check in vpd_platform_init()
goldfish_pipe: fix build warning about using too much stack.
goldfish_pipe: An implementation of more parallel pipe
fpga fr br: update supported version numbers
fpga: region: release FPGA region reference in error path
fpga altera-hps2fpga: disable/unprepare clock on error in alt_fpga_bridge_probe()
mei: drop the TODO from samples
firmware: Google VPD sysfs driver
firmware: Google VPD: import lib_vpd source files
misc: lkdtm: Add volatile to intentional NULL pointer reference
eeprom: idt_89hpesx: Add OF device ID table
misc: ds1682: Add OF device ID table
misc: tsl2550: Add OF device ID table
w1: Remove unneeded use of assert() and remove w1_log.h
w1: Use kernel common min() implementation
uio_mf624: Align memory regions to page size and set correct offsets
uio_mf624: Refactor memory info initialization
uio: Allow handling of non page-aligned memory regions
hangcheck-timer: Fix typo in comment
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Freescale MXS Low Resolution ADC
- Freescale i.MX23/i.MX28 LRADC touchscreen
- Motorola CPCAP Power Button
- TI LMU (Lighting Management Unit)
- Atmel SMC (Static Memory Controller)
New Device Support:
- Add support for X-Powers AXP803 to axp20x
- Add support for Dialog Semi DA9061 to da9062-core
- Add support for Intel Cougar Mountain to lpc_ich
- Add support for Intel Gemini Lake to lpc_ich
New Functionality:
- Add Device Tree support; wm831x-*, axp20x, ti-lmu, da9062, sun4i-gpadc
- Add IRQ sense support; motorola-cpcap
- Add ACPI support; cros_ec
- Add Reset support; altera-a10sr
- Add ADC support; axp20x
- Add AC Power support; axp20x
- Add Runtime PM support; atmel-ebi, exynos-lpass
- Add Battery Power Supply support; axp20x
- Add Clock support; exynos-lpass, hi655x-pmic
Fix-ups:
- Implicitly specify required headers; motorola-cpcap, intel_soc_pmic_bxtwc
- Add .remove() method; stm32-timers, exynos-lpass
- Remove unused code; intel_soc_pmic_core, intel-lpss-acpi, ipaq-micro, atmel-smc, menelaus
- Rename variables for clarity; axp20x
- Convert pr_warning() to pr_warn(); db8500-prcmu, sta2x11-mfd, twl4030-power
- Improve formatting; arizona-core, axp20x
- Use raw_spinlock_*() variants; asic3, t7l66xb, tc6393xb
- Simplify/refactor code; arizona-core, atmel-ebi
- Improve error checking; intel_soc_pmic_core
Bug Fixes:
- Ensure OMAP3630/3730 boards can successfully reboot; twl4030-power
- Correct max-register value; stm32-timers
- Extend timeout to account for clock stretching; cros_ec_spi
- Use correct IRQ trigger type; motorola-cpcap
- Fix bad use of IRQ sense register; motorola-cpcap
- Logic error "||" should be "&&"; mxs-lradc-ts"
* tag 'mfd-next-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (79 commits)
input: touchscreen: mxs-lradc: || vs && typos
dt-bindings: Add AXP803's regulator info
mfd: axp20x: Support AXP803 variant
dt-bindings: Add device tree binding for X-Powers AXP803 PMIC
dt-bindings: Make AXP20X compatible strings one per line
mfd: intel_soc_pmic_core: Fix unchecked return value
mfd: menelaus: Remove obsolete local_irq_disable() and local_irq_enable()
mfd: omap-usb-tll: Configure ULPIAUTOIDLE
mfd: omap-usb-tll: Fix inverted bit use for USB TLL mode
mfd: palmas: Fixed spelling mistake in error message
mfd: lpc_ich: Add support for Intel Gemini Lake SoC
mfd: hi655x: Add the clock cell to provide WiFi and Bluetooth
mfd: intel_soc_pmic: Fix a mess with compilation units
mfd: exynos-lpass: Add runtime PM support
mfd: exynos-lpass: Add missing remove() function
mfd: exynos-lpass: Add support for clocks
mfd: exynos-lpass: Remove pad retention control
iio: adc: add support for X-Powers AXP20X and AXP22X PMICs ADCs
mfd: cpcap: Fix bad use of IRQ sense register
mfd: cpcap: Use ack_invert interrupts
...
|
|
Add system sleep power management support to st_lsm6dsx driver.
In particular during suspend phase each sensor is disabled and
hw fifo is configured in bypass in order to avoid subsequent
I/O operations. The patch has been tested on HiKey board device
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
st_lsm6dsx_set_fifo_mode scope
Remove static qualifier from st_lsm6dsx_flush_fifo() and
st_lsm6dsx_set_fifo_mode() in order to use them in system sleep pm support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
isl29030 is basically the same chip. The only difference
is the chip's first pin. For isl29028 its named ADDR0 and
can be used to change the chip's i2c address. For isl29030
on the other hand that pin is named Ials and is an analog
current output proportional to ALS/IR. This change is
irrelevant for the Linux driver.
This has been tested on Motorola Droid 4.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
AS3935 interrupt mask has been incorrect so valid lightning events
would never trigger an buffer event. Also noise interrupt should be
BIT(0).
Fixes: 24ddb0e4bba4 ("iio: Add AS3935 lightning sensor support")
CC: stable@vger.kernel.org
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
