| Age | Commit message (Collapse) | Author |
|---|
|
This adds support for the SAR (Successive Approximation Register) ADC
on the Amlogic Meson SoCs.
The code is based on the public S805 (Meson8b) and S905 (GXBB)
datasheets (see [0] and [1]), as well as by reading (various versions
of) the vendor driver and by inspecting the registers on the vendor
kernels of my testing-hardware.
Currently the GXBB, GXL and GXM SoCs are supported. GXBB hardware has
10-bit ADC resolution, while GXL and GXM have 12-bit ADC resolution.
The code was written to support older SoCs (Meson8 and Meson8b) as well,
but due to lack of actual testing-hardware no of_device_id was added for
these.
Two "features" from the vendor driver are currently missing:
- the vendor driver uses channel #7 for calibration (this improves the
accuracy of the results - in my tests the results were less than 3%
off without calibration compared to the vendor driver). Adding support
for this should be easy, but is not required for most applications.
- channel #6 is connected to the SoCs internal temperature sensor.
Adding support for this is probably not so easy since (based on the
u-boot sources) most SoC versions are using different registers and
algorithms for the conversion from "ADC value" to temperature.
Supported by the hardware but currently not supported by the driver:
- reading multiple channels at the same time (the hardware has a FIFO
buffer which stores multiple results)
- continuous sampling (this would require a way to enable this
individually because otherwise the ADC would be drawing power
constantly)
- interrupt support (similar to the vendor driver this new driver is
polling the results. It is unclear if the IRQ-mode is supported on
older (Meson6 or Meson8) hardware as well or if there are any errata)
[0]
http://dn.odroid.com/S805/Datasheet/S805_Datasheet%20V0.8%2020150126.pdf
[1] http://dn.odroid.com/S905/DataSheet/S905_Public_Datasheet_V1.1.4.pdf
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add IIO driver for the Renesas RCar GyroADC block. This block is a
simple 4/8-channel ADC which samples 12/15/24 bits of data every
cycle from all channels.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-renesas-soc@vger.kernel.org
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into work-next
Jonathan writes:
Second round of IIO new device support, cleanups and features for the 4.11 cycle
New device support:
* lsm6dsx imu
- new driver and bindings.
* max11100 adc
- new driver and bindings.
* tlc4541
- new driver
* tmp007 thermopile
- new driver.
Core
* in kernel interfaces
- pass through raw values if no scaling provided and a processed value is
requested.
* trigger
- close a race condition in acquiring trigger reference.
- constify device_type structures.
- rework the viio_trigger_alloc function to be much neater and easier to
read.
- free trigger resources correctly on some error paths. Avoids putting a
module we don't have.
Documentation
* ABI
- specify a unit for proximity measurements.
Cleanups and features
* ads1015
- constify iio_info structure.
* ads7950 cleanups following merge in previous pull
- Add device tree bindings
- Drop the ti prefix from the module name in common with other drivers.
- Change regulator name to vref to match datasheet and other drivers.
* ak8974
- remove a redundant zero timeout check.
* bmi160
- use variable names for sizeof instead of types.
* cm3605
- mark PM functions as __maybe_unused to avoid a build warning.
* isl29028 (on it's way towards moving out of staging).
- alignment fixes and newline improvements.
- combine proxim_get and read_proxim for simpler code.
- drop unused ISL29028_DEV_ATTR macro
- move some error logging into functions to cut out repitition.
- make error messages more consistent.
- tidy up some brackets.
- drop the enable flag that nothing uses.
- only set proximity rate and ALS scale when relevant channel type is enabled.
- runtime pm support.
* lsm6dsx
- fix wrong values for gyro sensitivitiy.
* mag3110
- claim direct mode during sysfs reads to avoid a race condition.
* max1363
- export OF device table IDs as module aliases.
* max30100
- use msleep for long uncritical delays.
* mcp4531
- export OF device table as module aliases.
* ms5611
- claim direct mode during sysfs reads to avoid a race condition.
* opt3001
- export OF device table as module aliases.
* sx9500
- claim direct mode during oversampling changes to avoid a race condition.
|
|
Declare iio_info structures as const as they are only stored in
the info field of a iio_dev structure. This field is of type const,
so iio_info structures having similar properties can be made const too.
File size before:
text data bss dec hex filename
6944 792 0 7736 1e38 drivers/iio/adc/ti-ads1015.o
File size after:
text data bss dec hex filename
7264 472 0 7736 1e38 drivers/iio/adc/ti-ads1015.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This adds TI's tlc4541 16-bit ADC driver. Which is a single channel
ADC. Supports raw and trigger buffer access.
Also supports the tlc3541 14-bit device, which has not been tested.
Implementation of the tlc3541 is fairly straight forward thou.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The suspend/resume functions were using dev_to_iio_dev() to get
the iio_dev. That only works on IIO dev's. Use dev_get_drvdata()
for a platform device to get the correct iio_dev.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add iio driver for Maxim MAX11100 single-channel ADC.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new device support, features and cleanups for IIO in the 4.11 cycle.
It's shaping to be another fairly busy cycle. Lots more on the way!
New device support
* ads7950
- new driver supporting ads7950, ads7951, ads7952, ads7953, ads7954,
ads7955, ads7956, ads7957, ads7958, ads7959, ads7960, and ads7961 ADCs.
* cm3605
- New driver for this light sensor and proximity sensor which is an
analog part with some additional digital controls.
* hx711
- New driver.
Core new stuff
* Gravity sensor type. This is a processed datastream in which the device
will try to work out which way is down.
* Split the buffer.h file into two parts. One provides the interface to 'use'
a buffer, the second provides the internals of the buffer functionality as
needed by implementations of buffers.
- Move documentation inline so as to allow use of private: tag when
generating documentation.
- Add some utility functions for the few things that are directly done
with the buffers.
- Stop exporting functions that no-one uses outside of the core code.
- Push docs down by the code in the c file where they should have always
been.
- Fix typo in kernel-doc for buffer.
- push down some includes that were previously happening implicitly.
- stop enabling the timestamp of the dummy device.
Features and cleanups
* ad5592r
- ACPI support
* ad5593r
-ACPI support.
* ad5933
- Fix a false comment about size of a particular register.
* ad7150
- replace S_IRUGO | S_IWUSR with 0644. I'm not that keen on these patches
in general, but as it was nicely presented I took this one anyway. As a
general rule will only take these as part of a larger driver cleanup.
- don't eat an error but rather reutnr it in the write_event_config callback.
* ad7606
- replace non standard range attibute with _scale
* ade7753
- use usleep_range for short sleeps
* ade7754
- use usleep_range for short sleeps
* ade7758
- use usleep_range for short sleeps
* ade7759
- use usleep_range for short sleeps
* ade7854
- use usleep_range for short sleeps
* adis16201
- fix description
* adis16203
- fix description
- fix copyright year
* adis16209
- fix description
* adt7316
- Add braces to arms of if else statement (for consistency)
- Alignment fixes.
* axp288
- Fix up an issue with accidental overwrites of data.
* bmi160
- add deivce tables for i2c and spi to support correctly identifying the
full dt name (including manufacturer).
- device tree binding.
* bmp280
- use usleep_range for short sleeps.
* cm3232
- return error from cm3232_reg_init rather than eating it if the last write
fails.
* dummy driver
- remove a semicolor found at end of a function defintition.
* exynos-adc
- use usleep_range for short sleeps.
* hid-sensor (accel)
- Add timestamp support. The hardware can provide timestamps so lets support
them. If not fall back to timestamps estimated in kernel.
* hid-sensor (light)
- Add a duplicate ID for the light channels so as to keep existing interface
whilst also using the more standard IIO interface.
* hts221
- acpi probing
* imx25-gcq
- Add a macro call to allow this driver to be automatically loaded.
* isl29028
- reorganise code to avoid deep nesting of if statements.
- move chip test and default regs into a function suitable or sharing with
power management code.
- tidy up some code alignment.
* lidar-lite-v3
- introduce compatible strings that make it clear Garmin have consideral
friends.
* mma8452
- avoid returning signed value when unsigned is appropriate
* spmi-vadc
- Update function for generic voltage conversion to take into account that
different channels on this device should be handled differently.
- Rework code to allow per channel voltage scaling and support the standard
options for this hardware.
- Fixup three minor issues with the above patches for this part. These all
effect test builds rather than the native builds for the part, but good to
clean them up anyway.
* st_sensors
- support device matching from the ACPI DST tables.
- acpi based probing for accelerometers
- acpi based probing for pressure sensors
- Allow pressure sensors to read negative values.
- Export sampling frequency for lps25h and lps331ap.
- Add support for the old DT bindings from the period when these deivces
were often supported through windows.
Docs fixup:
* typo in sysfs-bus-iio
|
|
This changes the reference voltage regulator matching string from "refin"
to "vref". This is to be consistent with other A/DC chips that also use
"vref-supply" in their device tree bindings.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This drops the "ti-" prefix from the module name. It makes the module name
consistent with other iio ti-ads* drivers and it makes the driver work
with device tree (the spi subsystem drops the "ti," prefix when matching
compatible strings from device tree).
Tested working on LEGO MINDSTORMS EV3 with the following device tree node:
adc@3 {
compatible = "ti,ads7957";
reg = <3>;
#io-channel-cells = <1>;
spi-max-frequency = <10000000>;
vref-supply = <&adc_ref>;
};
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Another one of these that we missed previously which prevents test builds
of this driver on 32 bit platforms as it gives an undefined __divdi3 warning.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
It is meant to be long and is only added to an s64.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
A simple do_div call works here as all the signed 64 bit is
actually small and unsigned at this point, and the numerator is
u32.
Introduce a temporary u64 variable to avoid type comparison warnings
on some architectures.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This is the IIO driver for AVIA HX711 ADC which is mostly used in weighting
cells.
The protocol is quite simple and using GPIOs:
One GPIO is used as clock (SCK) while another GPIO is read (DOUT)
The raw value read from the chip is delivered.
To get a weight one needs to subtract the zero offset and scale it.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
For some reason the axp288_adc driver was modifying the
AXP288_ADC_TS_PIN_CTRL register, changing bits 0-1 depending on
whether the GP_ADC channel or another channel was written.
These bits control when a bias current is send to the TS_PIN, the
GP_ADC has its own pin and a separate bit in another register to
control the bias current.
Not only does changing when to enable the TS_PIN bias current
(always or only when sampling) when reading the GP_ADC make no sense
at all, the code is modifying these bits is writing the entire register,
assuming that all the other bits have their default value.
So if the firmware has configured a different bias-current for either
pin, then that change gets clobbered by the write, likewise if the
firmware has set bit 2 to indicate that the battery has no thermal sensor,
this will get clobbered by the write.
This commit fixes all this, by simply removing all writes to the
AXP288_ADC_TS_PIN_CTRL register, they are not needed to read the
GP_ADC pin, and can actually be harmful.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/iio/adc/fsl-imx25-gcq.ko | grep alias
$
After this patch:
$ modinfo drivers/iio/adc/fsl-imx25-gcq.ko | grep alias
alias: of:N*T*Cfsl,imx25-gcqC*
alias: of:N*T*Cfsl,imx25-gcq
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
As a precursor to splitting buffer.h, lets make sure all drivers
include the relevant headers rather than relying on picking them
up from kfifo_buf.h.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
|
|
If NO_DMA=y:
ERROR: "bad_dma_ops" [drivers/iio/adc/ti_am335x_adc.ko] undefined!
Add a dependency on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: f438b9da (" drivers: iio: ti_am335x_adc: add dma support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Several ADC channels are supported in PMIC which can be used to
measure voltage, temperature, current etc. Different scaling can be
applied on the obtained voltage to report in physical units. Scaling
functionality can be different per channel. Add scaling support per
channel. Every channel present in adc has an unique conversion formula
for obtained voltage. Add support to report in Raw as well as in
processed format. Scaling is applied when processed read is requested
and is not applied when a Raw read is requested.
Signed-off-by: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Several channels are supported in ADC of PMIC which can be used to
measure voltage, temperature, current etc., Hardware provides
readings for all channels in adc code. That adc code needs to be
converted to voltage. Logic for conversion of adc code to voltage
is common for all ADC channels(voltage, temperature, current
.,etc). Implement separate function for generic conversion logic.
Signed-off-by: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This adds a new driver for the TI ADS7950 family of ADC chips. These
communicate using SPI and come in 8/10/12-bit and 4/8/12/16 channel
varieties.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
msleep(1~20) may not do what the caller intends, and will often sleep longer.
(~20 ms actual sleep for any value given in the 1~20ms range)
This is not the desired behaviour for many cases like device resume time,
device suspend time, device enable time, data reading time, etc.
Thus, change msleep to usleep_range for precise wakeups.
Signed-off-by: Aniroop Mathur <a.mathur@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch adds support for STMicroelectronics STM32 MCU's analog to
digital converter.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add core driver for STMicroelectronics STM32 ADC (Analog to Digital
Converter). STM32 ADC can be composed of up to 3 ADCs with shared
resources like clock prescaler, common interrupt line and analog
reference voltage.
This core driver basically manages shared resources.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The DAC is used to find the peak level of an alternating voltage input
signal by a binary search using the output of a comparator wired to
an interrupt pin. Like so:
_
| \
input +------>-------|+ \
| \
.-------. | }---.
| | | / |
| dac|-->--|- / |
| | |_/ |
| | |
| | |
| irq|------<-------'
| |
'-------'
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
We should be testing "ret" here.
Fixes: aa16c6bd0e09 ("iio:adc: Add support for AD7766/AD7767")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing
Jonathan writes:
Second round of new device support, cleanups and fixes for IIO in the 4.10 cycle
This includes two branch merges for elements that may also go via MFD.
New device support
* cros_ec
- new driver to support these Chrome OS contiguous sensors which are behind
the Chrome OS embedded controller. Requires a few minor MFD and chrome
platform changes. One follow up fix deals with some dependency issues in
Kconfig.
* mpu-3050
- new driver and device tree bindings for this venerable device.
* st_accel
- support for the lng2dm an
Driver features
* ad7192
- Add DVdd regulator handling
* ad9832
- Add DVDD regulator handling
* at91
- Suspend and resume support
* si7020
- Device tree bindings
* ti-am335x
- DMA support - uses dma to accelerate short bursts of read back rather
than full blown DMA buffer support. Greatly improved performance.
Includes an MFD addition to give access to the address needed for DMA.
* tsl2583
- Device tree bindings
Cleanups and minor fixes
* ad7192
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
- Rename reg variable to reflect which regulator it is
* ad5933
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* ad7746
- Fix a missing return value (fallout from previous patch set)
* ad7780
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* ad9832
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
- Rename reg regulator to reflect which one it is
* ad9834
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* hts221
- Remove a duplicated include
* maxim thermocouple
- Handle a wrong storage side in read function. Prevent any problems that
might be introduced by additions to this driver in future.
* tsl2583 - big set from Brian Masney to drive this towards a staging
graduation.
- Convert to iio_chan_spec and read_raw / write_raw (in a couple of steps)
- Improved error handling in various functions
- Drop redundant power_state custom sysfs attribute.
- Use IIO_*_ATTR* macros for remaining attributes.
- Return an error code to userspace on invalid parameters being writen to
sysfs files.
- Add locking to various attribute accesses to remove possible races.
- Add defines for various magic numbers.
- Use smbus_read_byte_data instead of a write_byte followed by read_byte.
- Query only relevant registers in probe.
- Tidy up ordering of code comments.
- Remove a pointless power off sequence in taos_chip_on.
- Don't bother shutting down the chip when updating the lux table.
The table is held entirely in the driver and doesn't effect the chip at all.
- Drop a redundant i2c call in taos_als_calibrate where the same register
is read twice in a row.
|
|
A local branch created as Lee requested these two patches were applied
in a fashion that would later let him merge the same branch into MFD
if needed.
|
|
This patch adds the required pieces to ti_am335x_adc driver for
DMA support
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add suspend/resume callback, support the pinctrl sleep state when
the system suspend as well.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This resolves a merge issue with
drivers/staging/iio/accel/sca3000_core.c and we want the fixes all in
here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds triggered buffer support for the ti-adc0832 driver. Tested with
ADC0831 and ADC0832 by using SYSFS trigger.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Commit 08e05d1fce5c ("ti-adc081c: Initial triggered buffer support") added
triggered buffer support but that also requires CONFIG_IIO_TRIGGERED_BUFFER,
otherwise we get errors from linker such as:
drivers/built-in.o: In function `adc081c_remove':
drivers/iio/adc/ti-adc081c.c:225: undefined reference to `iio_triggered_buffer_cleanup'
Fix these by explicitly selecting both CONFIG_IIO_TRIGGERED_BUFFER and
CONFIG_IIO_BUFFER in Kconfig for the driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Allow IIO_CHAN_INFO_SCALE and IIO_CHAN_INFO_OFFSET attributes for
processing by checking voltage from a regulator.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add support for the AD7766, AD7766-1, AD7766-2, AD7767, AD7767-1, AD7767-2
Analog to Digital converters. It's a family of single channel 24-bit SAR
ADCs. They are all digital interface compatible and the main difference is
the internal decimation rate and analog performance. For communication with
the host processor a SPI interface is used.
In addition the part has a data ready pin that is pulsed for one MCLK cycle
when a conversion has completed and can be used as a IIO trigger.
Datasheets:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD7766.pdf
http://www.analog.com/media/en/technical-documentation/data-sheets/AD7767.pdf
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Use the new iio_trigger_validate_own_device() to verify that the trigger
can only be attached to the matching IIO device rather than using a custom
variant.
While the implementation of iio_trigger_validate_own_device() and the
custom variant and are not identical their behaviour is.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Fixing below warning:
drivers/iio/adc/max1027.c:241:34: warning: dubious: x | !y .
Signed-off-by: Sandhya Bankar <bankarsandhya512@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Check for iio_info structures that are only stored in the info field of a
iio_dev structure. This field is declared const, so iio_info structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct iio_info i@p = { ... };
@ok@
identifier r.i;
struct iio_dev e;
position p;
@@
e.info = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct iio_info e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct iio_info i = { ... };
// </smpl>
The result of size on this file before the change is:
text data bss dec hex filename
1529 312 0 1841 731
drivers/iio/adc/men_z188_adc.o
and after the change it is:
text data bss dec hex filename
1689 168 0 1857 741
drivers/iio/adc/men_z188_adc.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of iio new device support, features and cleanups for the 4.9 cycle.
New device support
* ad8801 dac
- new driver supporting ad8801 and ad8803 DACs.
* adc12138
- new driver supporting TI adc12130/adc12132 and adc12138 ADCs.
* ltc2485 adc
- new driver
* mxc6255
- add support for the mxc6225 part name and fixup the ID check so it works.
* vz89x VOC sensor
- add support for the vz89te part which drops the voc_short channel and adds
CRCs compared to other supported parts.
New features
* core
- immutable triggers. These effectively grant exclusive control over a
trigger. The typical usecase is a device representing an analog part
(perhaps a MUX) that needs to control the sampling of a downstream
ADC.
- resource managed trigger registration and triggered_buffer_init.
- iio_push_event now protected against case of the event interface
registration not having yet occured. Only matters if an interrupt
can occur during this window - might happen on shared interrupt lines.
- helper to let a driver query if the trigger it is using is provided by
itself (using the convention of both device and trigger having the same
parent).
* tools
- iio-utils. Used channel modifier scaling in preference to generic scaling
when both exist.
* at91-adc
- Add support for touchscreen switches closure time needed by some newer
parts.
* stx104
- support the ADC channels on this ADC/DAC board. As these are the primary
feature of the board also move the driver to the iio/adc directory.
* sx9500
- device tree bindings.
Cleanups / Fixes
* ad5755
- fix an off-by-one on devnr limit check (introduced earlier this cycle)
* ad7266
- drop NULL check on devm_regulator_get_optional as it can't return NULL.
* ak8974
- avoid an unused functional warning due to rework in PM core code.
- remove .owner field setting as done by i2c_core.
* ina2xx
- clear out a left over debug field from chip global data.
* hid-sensors
- avoid an unused functional warning due to rework in PM core code.
* maxim-thermocouple
- fix non static symbol warnings.
* ms5611
- fetch and enable regulators unconditionally when they aren't optional.
* sca3000
- whitespace cleanup.
* st_sensors
- fetch and enable regulators unconditionally rather than having them
supported as optional regulators (missunderstanding on my part amongst
others a while back)
- followup to previous patch fixes error checking on the regulators.
- mark symbols static where possible.
- use the 'is it my trigger' help function. This prevents the odd case
of another device triggering from the st-sensors trigger whilst the
st-sensors trigger is itself not using it but rather using say an hrtimer.
* ti-ads1015
- add missing of_node_put.
* vz89x
- rework to all support of new devices.
- prevent reading of a corrupted buffer.
- fixup a return value of 0/1 in a bool returning function.
Address updates
- Vlad Dogaru email address change.
|
|
On newer components compatible with the at91sam9x5, the Touchscreen
Switches Closure Time or TSSCTIM value of the Touchscreen Mode Register is
not filled at all.
On some hardware, having no time indicated for it may lead to incoherent
values and jitter.
We fix this time to 10us as it is usually difficult to retrieve impedance
values from LCD manufacturers.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch is inspired by a comment of Jonathan Cameron on patch of
Linus Walleij commit aeb55fff3891834e07a3144159a7298a19696af8 ("iio:
st_sensors: fetch and enable regulators unconditionally"). Because
changes made in this patch are actually reference generators they should
be using devm_regulator_get_optional, but if they do not explicitly set
the reference to NULL they should not be using IS_ERR_OR_NULL, but
simple IS_ERR check.
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
We want the staging fixes in here as well to handle merge issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Apex Embedded Systems STX104 features 16 channels of single-ended (8
channels of true differential) 16-bit analog input. Differential input
configuration may be selected via a physical jumper on the device.
Similarly, input polarity (unipolar/bipolar) is configured via a
physical jumper on the device.
Input gain selection is available to the user via software, thus
allowing eight possible input ranges: +-10V, +-5V, +-2.5V, +-1.25V,
0 to 10V, 0 to 5V, 0 to 2.5V, and 0 to 1.25V. Four input gain
configurations are supported: x1, x2, x4, and x8.
This ADC resolution is 16-bits (1/65536 of full scale). Analog input
samples are taken on software trigger; neither FIFO sampling nor
interrupt triggering is supported by this driver.
The Apex Embedded Systems STX104 is primarily an analog-to-digital
converter device. The STX104 IIO driver was initially placed in the DAC
directory because only the DAC portion of the STX104 was supported at
the time. Now that ADC support has been added to the STX104 IIO driver,
the driver should be moved to the more appropriate ADC directory.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
commit 1961bce76452 "iio: ina2xx: Remove trace_printk debug
statements" removed the code that used the chip->prev_ns field.
This patch cleans it up further by removing the unused field
and assignments.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This adds Texas Instruments' ADC12130/ADC12132/ADC12138 12-bit plus
sign ADC driver. I have tested with the ADC12138. The ADC12130 and
ADC12132 are not tested but these are similar to ADC12138 except that
the mode programming instruction is a bit different.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
ads1015_get_channels_config_of()
When terminating for_each_child_of_node() iteration with
break or return, of_node_put() should be used to prevent
stale device node references from being left behind.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Adds basic support for the LTC2485 ADC - a delta-sigma analog-to-digital
converter with an I2C interface that operates in single shot conversion
mode.
The driver supports an on board 5V reference and the power-on default
configuration which rejects both 50hz & 60hz line frequencies and
operates in 1x speed mode.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into work-testing
Jonathan writes:
First round of new features, device support and cleanups for IIO in the 4.9 cycle.
Device support
* ak8974
- New driver and bindings for this 2009 vintage magnetometer (it was very
popular back then!)
* atlas-ph-sensor
- ORP sensor support(I had to look up what one of these was)
* cio-dac
- New driver for Measurement Computing DAC boards
* dmard06
- New driver for Domintech DMARDO6 accelerometer. Also vendor prefix.
* dmard09
- New driver for Domintech DMARD09 accelerometer.
* maxim-thermocouple
- max6675 and max31855 new driver
* mt6577 auxdac
- new driver for this Mediatek chip mt2701, mt6577 and mt8173 have this
hardware.
* ti-adc161s626
- new driver for this TI single channel differential ADC.
* vcnl4000
- support vcnl4010 and vcnl4020 which are compatible for all features
currently supported by this driver.
New features
* Core
- Allow retrieving of underlying iio_dev from a callback buffer handle.
This is needed to allow client drivers to perform operations such as
configuring the trigger used.
* hid-sensors
- asynchronous resume support to avoid really long resume times.
* kxcjk-1013
- add the mysterious KIOX000A ACPI id seen in the wild.
* Tools
- lsiio now enumerates processed as well as raw channels.
Cleanup
* ad7298
- use iio_device_claim_direct_mode and friends to simplify locking around
mode switching and drop some boilerplate.
* ad7793
- use iio_device_claim_direct_mode and friends to simplify locking around
mode switching and drop some boilerplate.
* ade7854
- checkpatch fixups (alignment of parameters)
* atlas-ph-sensor
- use iio_device_claim_direct_mode and friends to simplify locking around
mode switching and drop some boilerplate.
- Switch to REGCACHE_NONE as there are no useful register to cache.
* bma180
- use iio_device_claim_direct_mode and friends to simplify locking around
mode switching and drop some boilerplate.
* hdc100x
- Add mention of the HDC1000 and HDC1008 to the Kconfig help text.
* isl29018
- Add driver specific prefixes to defines and function names.
- Remove excessive logging.
- Drop newlines which add nothing to readability.
- General tidying up of comments.
- Drop I2C_CLASS_HWMON as irrelevant to driver.
* isl29028
- Add driver specific prefixes to defines, enums and function names.
- Drop comma's from available attribute output as not ABI compliant.
- Drop I2C_CLASS_HWMON as irrelevant to driver.
* kxsd9
- devicetree bindings.
* mag3110
- This one wasn't locking to protect against mode switches during
raw_reads. Use the iio_claim_direct_mode function to fix this buglet.
* maxim-theromcouple
- Fix missing selects for triggered buffer support in Kconfig.
* nau7802
- Use complete instead of complete_all as only one completion at a time.
* sx9500
- Use complete instead of complete_all as only one completion at a time.
* us5182d
- Add a missing error code asignment instead of checking the result of
an already checked statement.
* vcnl4000
- Use BIT macro where appropriate.
- Refactor return codes in read_raw callback.
- Add some missing locking for concurrent accesses to the device.
|
|
SARADC controller needs to be reset before programming it, otherwise
it will not function properly.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-iio@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
