| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing
Jonathan writes:
2nd set of new device support, features and cleanup for IIO in the 4.7 cycle.
Bit of a bumper set for new drivers but plenty of other stuff here as well!
New device support
* ad5592R ADC/DAC
- new driver supporting ad5592r and ad5593r combined ADC/DAC and gpio chips.
* Aosong am2315 relative humidity
- new driver with triggered buffer support in follow up patch.
* bmi160 imu
- new driver
* bmp280
- bmp180 support - note there is support in the misc/bmp085 driver. Intent
is to remove that driver long term.
* invensense mpu6050
- cleanup leading to explicit support of mpu9150 with a good few cleanups
along the way.
* Hope RF hp03 pressure and temperature sensor.
- new driver
* maxim DS1803 potentiometer
- new driver
* maxim max44000 light and proximity sensor
- new driver built in a series of steps to support pretty much everything.
* ROHM BH1780 light sensor
- new driver. There is an existing driver in misc that this is pretty much
intended to replace. The discussion on whether to support the non standard
interface of that driver is some way is continuing.
* st-gyro
- lsm9ds0-gyro. The accel/magn side of this will take a while longer as
extensions to the st library are needed for cases where two types of sensor
share a single i2c address.
* ti-adc081c
- support the adc101c and adc121c
* Vishay VEML6070 UV sensor
- new driver.
New features
* core
- devm_ APIs for channel_get and channel_get_all. The first user of these
is the generic ADC based thermal driver. As it is going through the
thermal tree these will be picked up as a patch to that next cycle as that
is how the author preferred to do it.
- mounting matrix support. This new core support allows devices to provide
to userspace (typically from the device tree) allowing compensation for how
the sensor is mounted on the device. First examples are on UAVs but it
has a more mundane use on typical phone where the chip may be on the front
or the back of the circuit board and soldered at any angle. Includes
support for this ABI in ak8975 (which has an older interface, now
deprecated) and mpu6050.
* tools
- add a -a option to enable all available channels in generic_buffer sample.
Makes it somewhat easier to use.
* adis library and drivers
- support manual self test flag clearing. This has technically been broken
for a very long time - result is an offset on readings as the applied field
is on all the time.
* ak8975
- triggered buffer support
* bmc150
- spi support (including splitting the driver into core and i2c parts)
* bmp280
- oversampling support.
* dht11
- improved logging - useful to debug timing issues on this quirky device.
* st-sensors
- read each channel invidivually as not all support the optimization of
reading in bulk. This is technically a fix, but will need to be backported
if desired.
- support open drain and shared interrupts.
* ti-adc081c
- triggered buffer support.
Cleanups
* inkern
- white space fix.
* ad7606
- use the iio_device_claim_direct_mode call rather than open coding equiv.
* ad799x
- white space fix.
* ad9523
- unsigned -> unsigned int
* apds9660
- brace location tidying up.
- silence an uninitialized variable warning.
* ak8975
- else and brace on same line fix.
* at91_adc
- white space fixes.
* bmc150
- use regmap stored copy of the device pointer rather than having an
additional copy.
* bmg160
- use regmap stored copy of the device pointer rather than having an
additional copy.
* hid-sensors
- white space fixes.
* mcp3422
- white space fix.
* mma7455
- use regmap to retrieve the device struct rather than carrying another copy
in the private data.
* ms_sensors
- white space fix.
* mxs-lradc
- move current bindings out of staging - some will be shortly deprecated but
the reality is that we have device trees out there using them so they will
need to be supported for some time. They accidentally got left behind
when the driver graduated from staging.
- white space cleanup.
- set INPUT_PROP_DIRECT.
- move ts config into a better function.
- move the STMP reset out of the ADC init.
* vf610_adc
- case label indenting fix.
|
|
Driver includes struct regmap and struct device in its global data.
Remove the struct device and use regmap API to retrieve device info.
Patch created using Coccinelle plus manual edits.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Reviewed-by: Irina Tirdea <irina.tirdea@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Some types of ST Sensors can be connected to the same IRQ line
as other peripherals using open drain. Add a device tree binding
and a sensor data property to flip the right bit in the interrupt
control register to enable open drain mode on the INT line.
If the line is set to be open drain, also tag on IRQF_SHARED
to the IRQ flags when requesting the interrupt, as the whole
point of using open drain interrupt lines is to share them with
more than one peripheral (wire-or).
Cc: devicetree@vger.kernel.org
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Acked-by: Rob Herring <rob@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This makes all ST sensor drivers check that they actually have
new data available for the requested channel(s) before claiming
an IRQ, by reading the status register (which is conveniently
the same for all ST sensors) and check that the channel has new
data before proceeding to read it and fill the buffer.
This way sensors can share an interrupt line: it can be flaged
as shared and then the sensor that did not fire will return
NO_IRQ, and the sensor that fired will handle the IRQ and
return IRQ_HANDLED.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This resolves a lot of merge issues with PAGE_CACHE_* changes, and an
iio driver merge issue.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Driver includes struct regmap and struct device in its global data.
Remove the struct device and use regmap API to retrieve device info.
Patch created using Coccinelle plus manual edits.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
bmc150_i2c_regmap_conf is defined three times (in bmc150-accel-core.c,
bmc150-accel-i2c.c and and bmc150-accel-spi.c), although the
definition is the same.
Use one common definition for bmc150_i2c_regmap_conf in all
included files.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
For big endian platforms, reading the axes will return
invalid values.
The device stores each axis value in a 16 bit little
endian register. The driver uses regmap_read_bulk to get
the axis value, resulting in a 16 bit little endian value.
This needs to be converted to cpu endianness to work
on big endian platforms.
Fix endianness for big endian platforms by converting
the values for the axes read from little endian to
cpu.
This is also partially fixed in commit b6fb9b6d6552 ("iio:
accel: bmc150: optimize transfers in trigger handler").
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Commit 845c877009cf014b ("i2c / ACPI: Assign IRQ for devices that have
GpioInt automatically") automatically assigns the first ACPI GPIO
interrupt in client->irq, so we can remove the probing code from
drivers that use only one interrupt.
Commit 0f0796509c07c1c7 ("iio: remove gpio interrupt probing from drivers
that use a single interrupt") removes gpio interrupt probing from most
drivers. This patch cleans the remaining ones.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
GPIO handling code has been removed from the drivers (since
this is now handled by the ACPI core) in commit 0f0796509c07 ("iio:
remove gpio interrupt probing from drivers that use a single interrupt").
Remove the include for linux/gpio/consumer.h since it is no longer
used.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Some i2c busses (e.g.: Synopsys DesignWare I2C adapter) need to
enable/disable the bus at each i2c transfer and must wait for
the enable/disable to happen before sending the data.
When reading data in the trigger handler, the kxcjk-1013 accel driver
does one i2c transfer for each axis. This has an impact on the
frequency of the accelerometer at high sample rates due to additional
delays introduced by the i2c bus at each transfer.
Reading all axis values in one i2c transfer reduces the delays
introduced by the i2c bus. Uses i2c_smbus_read_i2c_block_data_or_emulated
that will fallback to reading each axis as a separate word in case i2c
block read is not supported.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Use available_scan_masks to allow the iio core to select
the data to send to userspace depending on which axes are
enabled, instead of doing this in the driver's interrupt
handler.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Some i2c busses (e.g.: Synopsys DesignWare I2C adapter) need to
enable/disable the bus at each i2c transfer and must wait for
the enable/disable to happen before sending the data.
When reading data in the trigger handler, the bmc150 accel driver does
one bus transfer for each axis. This has an impact on the frequency
of the accelerometer at high sample rates due to additional delays
introduced by the bus at each transfer.
Reading all axis values in one bus transfer reduces the delays
introduced by the bus.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Use available_scan_masks to allow the iio core to select
the data to send to userspace depending on which axes are
enabled, instead of doing this in the driver's interrupt
handler.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
What is this autosleep?
-----------------------
It slows down the device after x seconds of inactivity. The thing is, we have
really achieved almost the same by runtime pm.
differnces are:
autosleep
* uses more power during inactivity
* the first read after inactivity slightly faster
* complicated to understand for the user
* no documented sysfs interface (afaik)
* complicated to read and maintain
runtime pm
* already merged in mma8452
* uses less power during inactivity
* first read after inactivity slower
* easy to use. well documented.
* easy to maintain and understand
The two approaches solve the same problem. runtime pm has more advantages
than autosleep and comes quite close to it's behaviour anyways. As I see it,
autosleep, even if somehow supported, would never be used anyways.
So resolve this issue by "ignoring" autosleep.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Reviewed-by: Martina Kepplinger <martina.novakovic@zoho.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This was forgotten about and is added for consistency now
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This adds support for Freescale's (now NXP's) FXLS8471Q accelerometer.
We use MMA8451Q's configuration because for what the driver supports,
FXLS8471Q is the same.
Support for FXLS8471Q's features (fast SPI interface and a larger FIFO,
among others) can be added to this driver anytime.
See it's datasheet for the details:
http://cache.nxp.com/files/sensors/doc/data_sheet/FXLS8471Q.pdf
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This commit adds support for STMicroelectronics h3lis331dl high-g
accelerometer. The datasheet for this device can be found here:
http://www.st.com/web/en/resource/technical/document/
datasheet/DM00053090.pdf
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Reviewed-by: Denis Ciocca <denis.ciocca@st.com>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This adds support for runtime power management and, if configured, activates
automatic standby after 2 seconds of inactivity.
Inactivity means no read of acceleration values and no events triggered or
activated.
If CONFIG_PM is not set, this doesn't change anything for existing users.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The devices' config registers can only be changed in standby mode.
Up until now the driver just held the device *always* active, so for
changing a config it was *always* necessary to switch to standby.
For upcoming support for runtime pm, the device can as well be in standby
mode. Instead of putting runtime pm functions in there, just keep the
device in standby if it already is. This section is protected by a lock
after all.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
fix checkpatch issues like "space before tabs", too long lines or alignment.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
We want the upstream staging fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.5 cycle.
This set comprises those not dependent on patches in the 4.5 merge cycle.
A second set will follow shortly with ones that are.
* core in kernel interfaces
- fix a possible NULL dereference that is a theoretical possibility
via odd usage of iio_channel_release. Pretty much a hardening of
the interface, but observed in the wild with the twl4030_charger
driver.
* acpi-als
- report the data as processed as it is in lux. This fixes a wrong
use of the IIO ABI. However, old _raw version retained to avoid
breaking any userspace in the wild that is relying on that (none
known but it doesn't hurt us much to retain it)
* ade7753
- fix some error handling to avoid use of unitialized data.
* ltr501
- use a signed return type for ltr501_match_samp_freq so as to allow
returning of an error code.
* mcp4725
- set name field of struct iio_dev to ensure the sysfs name attribute
doesn't give NULL.
* mpl115
- temperature offset sign is wrong.
* stk8ba50
- IIO_TRIGGER dependency added
* ti_am335x_adc
- Label buffer as a software buffer. It's actually a hybrid of a
true hardware buffer feeding a kfifo, but the meaning of these fields
has changed a little recently and in this case it should be labeled
a software buffer ensure it is allowed to use the kfifo.
* vf610_adc
- HAS_IOMEM dependency
|
|
This adds support for this series' 14 bit accelerometer chip, MMA8451Q.
It's datasheet is available at the vendor's website:
https://cache.freescale.com/files/sensors/doc/data_sheet/MMA8451Q.pdf
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This adds freefall event detection to the supported devices. It adds
the in_accel_x&y&z_mag_falling_en iio event attribute, which activates
freefall mode.
In freefall mode, the current acceleration magnitude (AND combination
of all axis values) is compared to the specified threshold.
If it falls under the threshold (in_accel_mag_falling_value),
the appropriate IIO event code is generated.
This is what the sysfs "events" directory for these devices looks
like after this change:
-rw-r--r-- 4096 Oct 23 08:45 in_accel_mag_falling_period
-rw-r--r-- 4096 Oct 23 08:45 in_accel_mag_falling_value
-rw-r--r-- 4096 Oct 23 08:45 in_accel_mag_rising_period
-rw-r--r-- 4096 Oct 23 08:45 in_accel_mag_rising_value
-r--r--r-- 4096 Oct 23 08:45 in_accel_scale
-rw-r--r-- 4096 Oct 23 08:45 in_accel_x&y&z_mag_falling_en
-rw-r--r-- 4096 Oct 23 08:45 in_accel_x_mag_rising_en
-rw-r--r-- 4096 Oct 23 08:45 in_accel_y_mag_rising_en
-rw-r--r-- 4096 Oct 23 08:45 in_accel_z_mag_rising_en
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Most ST MEMS Sensors that support interrupts can also handle sending
an active low interrupt, i.e. going from high to low on data ready
(or other interrupt) and thus triggering on a falling edge to the
interrupt controller.
Set up logic to inspect the interrupt line we get for a sensor: if
it is triggering on rising edge, leave everything alone, but if it
triggers on falling edges, set up active low, and if unsupported
configurations appear: warn with errors and reconfigure the interrupt
to a rising edge, which all interrupt generating sensors support.
Create a local header for st_sensors_core.h to share functions
between the sensor core and the trigger setup code.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Ran into this on UML:
drivers/iio/accel/stk8ba50.c: In function ‘stk8ba50_data_rdy_trigger_set_state’:
drivers/iio/accel/stk8ba50.c:163:9: error: implicit declaration of function ‘iio_trigger_get_drvdata’ [-Werror=implicit-function-declaration]
iio_trigger_get_drvdata() is defined only when IIO_TRIGGER is selected.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This gets rid of some magic numbers by adding an enum.
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 4.5 cycle
Usual mixed bag, but the big item perhaps in this series is the DMA buffer
support added by Lars-Peter Clausen. It's been in the works for a long time
and it will be interesting to see what hardware support shows up now that
this is available.
New core features + associate cleanup.
* Add generic DMA buffer infrastructure
* Add a DMAengine framework based buffer
Also associated minor changes.
- Set the device buffer watermark based on the minimum watermark for all
attached buffers rather than just the 'primary' one.
- iio_buffer_init - only set the watermark default if one hasn't already
been provided. This allows simple support for devices with a fixed
watermark.
- read only attribute for watermark on fixed watermark devices.
- add explicit buffer enable/disable callbacks to allow the buffer to
do more than trivial actions when it is being turned on and off.
* IIO_VAL_INT support in write_raw_get_fmt function.
New device support
* Freescale MMA7455/7456L accelerometers
* Memsic MXC6255XC accelerometer
* ST lis2dh12 accelerometer
* TI ADS8688 ADC
* TI Palamas (twl6035/7) gpadc
New driver features
* mma8452
- support either of the available interrupt pins to cope with the case
where board layout has lead to a particular one being connected.
Staging graduation
* Dummy driver
- this driver acts as both an example and a test device for those with
out hardware to develop userspace code against.
Cleanups and minor bits and bobs.
* treewide
- Sort out the ordering of iio_device_register/unregister vs runtime
pm function calls so that it's all nice and consistent and not race
prone.
- Check sscanf return values. None of the cases will actually happen as
the strings are supplied internally, but best to be consistent on this.
* ad7780
- switch over to the gpio descriptor interface and remove the now unused
platform data which gets rid of a header entirely.
* ad7793
- drop a pointless else statement.
* at91_adc
- Swap kmalloc_array in for a kmalloc doing the same job.
* dummy
- get rid of some commented out lines that snuck in during the move of
the driver.
* lm3533-als
- Print an error message on provision of an invalid resistance.
* mcp320x
- Add compatible strings with vendor prefix and deprecate those with
no vendor prefix.
* mxs-lradc
- Use BIT macro in various places rather than shifted ones.
* pa12203001
- Power off the chip if the registration fails.
* pulsedlight-lidar-lite
- add runtime PM support.
* xilinx XADC
- constify an iio_buffer_setup_ops structure.
|
|
This commit add support for STMicroelectronics lis2dh12 accelerometer.
Datasheet for this device can be found here:
http://www.st.com/st-web-ui/static/active/en/resource/technical/
document/datasheet/DM00091513.pdf
Signed-off-by: Giuseppe Barba <giuseppe.barba@st.com>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
At probe, runtime pm should be setup before registering the sysfs interface so
that all the power attributes are accurate and functional when registering.
Also, when removing the device we should unregister first to make sure
that the interfaces that may result in wakeups are no longer available.
Fix this behaviour for the following drivers: bmc150, bmg160, kmx61,
kxcj-1013, mma9551, mma9553, rpr0521.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
|
|
'spi/topic/omap-uwire', 'spi/topic/owner', 'spi/topic/pxa' and 'spi/topic/pxa2xx' into spi-next
|
|
Add support for Freescale MMA7455L/MMA7456L 3-axis in 10-bit mode for
I2C and SPI bus. This rather simple driver that currently doesn't
support all the hardware features of MMA7455L/MMA7456L.
Tested on Embedded Artist's LPC4357 Dev Kit with MMA7455L on I2C bus.
Data sheets for the two devices can be found here:
http://cache.freescale.com/files/sensors/doc/data_sheet/MMA7455L.pdf
http://cache.freescale.com/files/sensors/doc/data_sheet/MMA7456L.pdf
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We want the other staging patches in this branch as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds a minimal implementation for the Memsic MXC6255XC
orientation sensing accelerometer. The supported operations are reading
raw acceleration values for X/Y axis that can be scaled using the
exposed scale.
Signed-off-by: Teodora Baluta <teodora.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This change is important in order for everyone to be easily able to use the
driver for one of the supported accelerometer chips!
Until now, the driver blindly assumed that the INT1 interrupt line is wired
on a user's board. But these devices have 2 interrupt lines and can route
their interrupt sources to one of them. Now, if "INT2" is found and matches
i2c_client->irq, INT2 will be used.
The chip's default actually is INT2, which is why probably many boards will
have it wired and can make use of this.
Of course, this also falls back to assuming INT1, so for existing users
nothing will break. The new functionality is described in the bindings doc.
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
For the binding: Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add a simple SPI driver which initializes the spi regmap for the bmc150
core driver.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
i2c_client struct is now only used for debugging output. We can use the
device struct as well so we can remove all struct i2c_client usage.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This replaces all usage of direct i2c accesses with regmap accesses.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Commit 845c877009cf014b ("i2c / ACPI: Assign IRQ for devices that have
GpioInt automatically") automatically assigns the first ACPI GPIO
interrupt in client->irq, so we can remove the probing code from
drivers that use only one interrupt.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Since commit dab472eb931bc291 ("i2c / ACPI: Use 0 to indicate that
device does not have interrupt assigned") 0 is not a valid i2c
client irq anymore, so change all driver's checks accordingly.
The same issue occurs when the device is instantiated via device tree
with no IRQ, or from the i2c sysfs interface, even before the patch
above.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This accelerometer accidentally either emits a DRDY signal or an
IRQ signal. Accidentally I activated the IRQ signal as I thought
it was analogous to the interrupt generator on other ST
accelerometers. This was wrong. After this patch generic_buffer
gives a nice stream of accelerometer readings.
Fixes: 3acddf74f807778f "iio: st-sensors: add support for lis3lv02d accelerometer"
Cc: Denis CIOCCA <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This doesn't actually change anything since the core names the sysfs folder
for the iio event attributes "events" anyways. It only leaves the job to the
core.
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
MMA8652FC and MMA8653FC don't provide the transient interrupt source, so
the motion interrupt source is used by providing a new iio_chan_spec
definition, so that other supported devices are not affected by this.
Datasheets for the newly supported devices are available at Freescale's
website:
http://cache.freescale.com/files/sensors/doc/data_sheet/MMA8652FC.pdf
http://cache.freescale.com/files/sensors/doc/data_sheet/MMA8653FC.pdf
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
