| Age | Commit message (Collapse) | Author |
|---|
|
If an i2c topology has instances of nested muxes, then a lockdep splat
is produced when when i2c_parent_lock_bus() is called. Here is an
example:
============================================
WARNING: possible recursive locking detected
--------------------------------------------
insmod/68159 is trying to acquire lock:
(i2c_register_adapter#2){+.+.}, at: i2c_parent_lock_bus+0x32/0x50 [i2c_mux]
but task is already holding lock:
(i2c_register_adapter#2){+.+.}, at: i2c_parent_lock_bus+0x32/0x50 [i2c_mux]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(i2c_register_adapter#2);
lock(i2c_register_adapter#2);
*** DEADLOCK ***
May be due to missing lock nesting notation
1 lock held by insmod/68159:
#0: (i2c_register_adapter#2){+.+.}, at: i2c_parent_lock_bus+0x32/0x50 [i2c_mux]
stack backtrace:
CPU: 13 PID: 68159 Comm: insmod Tainted: G O
Call Trace:
dump_stack+0x67/0x98
__lock_acquire+0x162e/0x1780
lock_acquire+0xba/0x200
rt_mutex_lock+0x44/0x60
i2c_parent_lock_bus+0x32/0x50 [i2c_mux]
i2c_parent_lock_bus+0x3e/0x50 [i2c_mux]
i2c_smbus_xfer+0xf0/0x700
i2c_smbus_read_byte+0x42/0x70
my2c_init+0xa2/0x1000 [my2c]
do_one_initcall+0x51/0x192
do_init_module+0x62/0x216
load_module+0x20f9/0x2b50
SYSC_init_module+0x19a/0x1c0
SyS_init_module+0xe/0x10
do_syscall_64+0x6c/0x1a0
entry_SYSCALL_64_after_hwframe+0x42/0xb7
Reported-by: John Sperbeck <jsperbeck@google.com>
Tested-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Deepa Dinamani <deepadinamani@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Chang <dpf@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Link: http://lkml.kernel.org/r/20180720083914.1950-3-peda@axentia.se
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
I2C is open drain, so request the GPIO accordingly, even if pinmux did
set it up correctly for in-kernel users in this case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
On Gen3, we can only do RXDMA once per transfer reliably. For that, we
must reset the device, then we can have RXDMA once. This patch
implements this. When there is no reset controller or the reset fails,
RXDMA will be blocked completely. Otherwise, it will be disabled after
the first RXDMA transfer. Based on a commit from the BSP by Hiromitsu
Yamasaki, yet completely refactored to handle multiple read messages
within one transfer.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
On Gen3, we can only do RXDMA once per transfer reliably. For that, we
must reset the device, then we can have RXDMA once. This patch
implements this. When there is no reset controller or the reset fails,
RXDMA will be blocked completely. Otherwise, it will be disabled after
the first RXDMA transfer. Based on a commit from the BSP by Hiromitsu
Yamasaki, yet completely refactored to handle multiple read messages
within one transfer.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Make sure to call reinit_completion() before dma is started to avoid race
condition where reinit_completion() is called after complete() and before
wait_for_completion_timeout().
Signed-off-by: Esben Haabendal <eha@deif.com>
Fixes: ce1a78840ff7 ("i2c: imx: add DMA support for freescale i2c driver")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
If CLKH is set to 0 I2C clock is not generated at all, so avoid this value
and stretch the clock in this case.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This patch adjusts spinlock scope to make it wrap the whole irq
handler using a single lock/unlock which covers both master and
slave handlers.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This patch changes the order of enum aspeed_i2c_master_state and
enum aspeed_i2c_slave_state defines to make their initial value to
ASPEED_I2C_MASTER_INACTIVE and ASPEED_I2C_SLAVE_STOP respectively.
In case of multi-master use, if a slave data comes ahead of the
first master xfer, master_state starts from an invalid state so
this change fixes the issue.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
There are some log printing without a newline character. This
patch adds the missing newline characters.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The driver supports multiple hardware variants of Exynos I2C controller
which differ in FIFO depth, handling of interrupts and bus recovery in
HSI2C_MASTER_ST_LOSE state.
The difference in variant was a single bit set for Exynos7 variants and
implicit lack of this bit for other variants.
Make each variant explicit which also fixes the GCC warning about
documentation:
drivers/i2c/busses/i2c-exynos5.c:223: warning: Function parameter or member 'hw' not described in 'exynos_hsi2c_variant'
No change in functionality.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
When we initialize the pins, make sure it looks like STOP by dividing
the delay into halves. It shouldn't matter because SDA is expected to be
held low by a device, but for super-safety, let's do it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Bus recovery should reset the bus with the standard i2c recovery
procedure. Populate the necessary fields so that the standard procedure
can perform the reset.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Since there are many ports per master, each with it's own adapter and
chardev, we need some locking to prevent transfers from changing the
master state while other transfers are in progress.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Execute I2C transfers from the FSI-attached I2C master. Use polling
instead of interrupts as we have no hardware IRQ over FSI.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add abort procedure for failed transfers. Add engine reset procedure
that is executed during the abort to recover from various fault
conditions.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add and initialize I2C adapters for each port on the FSI-attached I2C
master. Ports for each master are defined in the devicetree.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add register definitions for FSI-attached I2C master and functions to
access those registers over FSI. Add an FSI driver so that our I2C bus
is probed up during an FSI scan.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Removes all locking from i2c_smbus_xfer and renames it to __i2c_smbus_xfer,
then adds a new i2c_smbus_xfer function that simply grabs the lock while
calling the unlocked variant.
This is not perfectly equivalent, since i2c_smbus_xfer was callable from
atomic/irq context if you happened to end up emulating SMBus with an I2C
transfer, and that is no longer the case with this patch. It is unknown
(to me) if anything depends on that quirk, but it seems fragile enough to
simply break those cases and require them to call i2c_transfer directly
instead.
While at it, for consistency rename the 2nd to last argument (size) of
the i2c_smbus_xfer declaration to protocol and remove the surplus extern
marker.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
While refactoring the routine before, it occurred to me that this will
make the code much easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
To break out of recovery as early as possible, feed back the bus_free
logic state.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Some IP cores have an internal 'bus free' logic which may be more
advanced than just checking if SDA is high. Add a separate callback to
get this status. Filling it is optional.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
After exiting the while loop, we checked if recovery was successful and
sent a STOP to the clients. Meanwhile however, we send a STOP after
every pulse, so it is not needed after the loop. If we move the check
for a free bus to the end of the while loop, we can shorten and simplify
the logic. It is still ensured that at least one STOP will be sent to
the wire even if SDA was not stuck low.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
For bus recovery, we either need to bail out early if we can read SDA or
we need to send STOP after every pulse. Otherwise recovery might be
misinterpreted as an unwanted write. So, require one of those SDA
handling functions to avoid this problem.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Linux 4.18-rc5
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
- I2C core bugfix regarding bus recovery
- driver bugfix for the tegra driver
- typo correction
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: recovery: if possible send STOP with recovery pulses
i2c: tegra: Fix NACK error handling
i2c: stu300: use non-archaic spelling of failes
|
|
|
|
The i2c_lock_adapter name is ambiguous since it is unclear if it
refers to the root adapter or the adapter you name in the argument.
The natural interpretation is the adapter you name in the argument,
but there are historical reasons for that not being the case; it
in fact locks the root adapter. Just remove the function and force
users to spell out the I2C_LOCK_ROOT_ADAPTER name to indicate what
is really going on. Also remove i2c_unlock_adapter, of course.
This patch was generated with
git grep -l 'i2c_\(un\)\?lock_adapter' \
| xargs sed -i 's/i2c_\(un\)\?lock_adapter(\([^)]*\))/'\
'i2c_\1lock_bus(\2, I2C_LOCK_ROOT_ADAPTER)/g'
followed by white-space touch-up.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Locking the root adapter for __i2c_transfer will deadlock if the
device sits behind a mux-locked I2C mux. Switch to the finer-grained
i2c_lock_bus with the I2C_LOCK_SEGMENT flag. If the device does not
sit behind a mux-locked mux, the two locking variants are equivalent.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
I2C clients may misunderstand recovery pulses if they can't read SDA to
bail out early. In the worst case, as a write operation. To avoid that
and if we can write SDA, try to send STOP to avoid the
misinterpretation.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
On Tegra30 Cardhu the PCA9546 I2C mux is not ACK'ing I2C commands on
resume from suspend (which is caused by the reset signal for the I2C
mux not being configured correctl). However, this NACK is causing the
Tegra30 to hang on resuming from suspend which is not expected as we
detect NACKs and handle them. The hang observed appears to occur when
resetting the I2C controller to recover from the NACK.
Commit 77821b4678f9 ("i2c: tegra: proper handling of error cases") added
additional error handling for some error cases including NACK, however,
it appears that this change conflicts with an early fix by commit
f70893d08338 ("i2c: tegra: Add delay before resetting the controller
after NACK"). After commit 77821b4678f9 was made we now disable 'packet
mode' before the delay from commit f70893d08338 happens. Testing shows
that moving the delay to before disabling 'packet mode' fixes the hang
observed on Tegra30. The delay was added to give the I2C controller
chance to send a stop condition and so it makes sense to move this to
before we disable packet mode. Please note that packet mode is always
enabled for Tegra.
Fixes: 77821b4678f9 ("i2c: tegra: proper handling of error cases")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org
|
|
Intel Ice Lake has the same SMBus host controller than Intel Cannon
Lake. Add the PCI ID to the drivers list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[jarkko.nikula@linux.intel.com: Add entries to Documentation and Kconfig]
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Make list of supported chipsets a little bit shorter by consolidating
names that belong to the same family.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
In order to support advanced features, the I2C FIFO interface was
changed in the version of the Tegra I2C controller found in Tegra194.
The changes are backwards incompatible, so the driver needs to be
programmed in a slightly different way on new chips.
Add support for MST FIFO programming and add an OF match entry for
Tegra194. At the same time, mark all prior generations of this
controller as not having the MST FIFO interface.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add another injector for an incomplete transfer. As mentioned in the
docs, this one is important to check bus recovery algorithms with it.
Otherwise random data may be sent to devices!
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Make the incomplete_transfer routine reusable, so we can add other test
cases with different patterns later. Prepare the docs for that, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Trivial added debug print for dev->clk_freq doesn't necessarily tell the
actual bus speed or mode the controller is operating. For instance it
may indicate 1 MHz Fast Mode Plus or 3.4 MHz High Speed but driver ends up
using 400 kHz Fast Mode due missing timing parameters or missing support
from HW.
Add a debug print that prints the bus speed based on the validated speed
that gets programmed into a HW.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
SDA hold time is an important timing parameter and often reason for
arbitration lost errors if not set to a correct value. Add a debug print
for it in order to see what value gets programmed to a HW.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Mixed timing parameter validation, calculation and their debug prints
with HW initialization in i2c_dw_init_master() and i2c_dw_init_slave()
as been bothering me some time.
It makes function a little bit unclear to follow, doesn't show what steps
are needed to do only once during probe and what are needed whenever HW
needs to be reinitialized. Also those debug prints show information that
doesn't change runtime and thus are also needlessly printed multiple times
whenever HW is reinitialized.
Thus let the i2c_dw_init_master() and i2c_dw_init_slave() to do only HW
initialization and move out one time parameter setting and debug prints
to separate functions which are called only during probe.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
SDA hold time configuration is common to both master and slave code. It
is also something that can be done once during probe and do only
register write when HW needs to be reinitialized.
Remove duplication and move SDA hold time configuration to common code.
It will be called from slave probe and for master code from a new
i2c_dw_set_timings_master() to where we will populate more probe time
timing parameter setting.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This is rather readability update than micro-optimization, or if not
optimization at all. We take the input clock rate to a variable and pass
that to SCL timing parameter calculation functions.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
It looks ___constant_swab32 is an internal byte swap detail. Switch to
swap32() and include header file for it explicitly. Now it comes
implicitly via linux/i2c.h include.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Move register access detection out from master and slave HW
initialization code to common code. Motivation for this is to have
register access configured before HW initialization and remove
duplicated code.
This allows to do further separation between probe time initialization
and runtime reinitialization code.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Commit 43df43e6ba13 ("i2c: designware: Don't set SCL timings and speed
mode when in slave mode") made variable comp_param1 needless in
i2c_dw_init_slave(). Remove it now.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Calling the __i2c_smbus_xfer wrapper in __i2c_mux_smbus_xfer provides
retries and thus makes the parent-locked case consistent with the both
mux-locked (i2c_mux_smbus_xfer) and the I2C transfer cases.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This simplifies the code, and you get retries for free if the adapter
does not support ->master_xfer.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This simplifies the code, and you get retries for free if the adapter
does not support ->master_xfer.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This simplifies the code, and you get retries for free if the adapter
does not support ->master_xfer.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Removes all locking from i2c_smbus_xfer and renames it to __i2c_smbus_xfer,
then adds a new i2c_smbus_xfer function that simply grabs the lock while
calling the unlocked variant.
This is not perfectly equivalent, since i2c_smbus_xfer was callable from
atomic/irq context if you happened to end up emulating SMBus with an I2C
transfer, and that is no longer the case with this patch. It is unknown
(to me) if anything depends on that quirk, but it seems fragile enough to
simply break those cases and require them to call i2c_transfer directly
instead.
While at it, for consistency rename the 2nd to last argument (size) of
the i2c_smbus_xfer declaration to protocol and remove the surplus extern
marker.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Commit f2a8aa053c17 ("typec: tcpm: Represent source supply through
power_supply") moved the code to register a power_supply representing
the device supplying power to the type-C connector, from the fusb302
code to the generic tcpm code.
This has caused the power-supply registered by the fusb302 driver,
which determines how much current the bq24190 can draw, to change name
from "fusb302-typec-source" to "tcpm-source-psy-i2c-fusb302".
Fixes: f2a8aa053c17 ("typec: tcpm: Represent source supply through...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
