summaryrefslogtreecommitdiff
path: root/drivers/i2c
AgeCommit message (Collapse)Author
2020-09-27i2c: npcm7xx: Clear LAST bit after a failed transaction.Tali Perry
Due to a HW issue, in some scenarios the LAST bit might remain set. This will cause an unexpected NACK after reading 16 bytes on the next read. Example: if user tries to read from a missing device, get a NACK, then if the next command is a long read ( > 16 bytes), the master will stop reading after 16 bytes. To solve this, if a command fails, check if LAST bit is still set. If it does, reset the module. Fixes: 56a1485b102e (i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver) Signed-off-by: Tali Perry <tali.perry1@gmail.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-09-27i2c: cpm: Fix i2c_ram structureNicolas VINCENT
the i2c_ram structure is missing the sdmatmp field mentionned in datasheet for MPC8272 at paragraph 36.5. With this field missing, the hardware would write past the allocated memory done through cpm_muram_alloc for the i2c_ram structure and land in memory allocated for the buffers descriptors corrupting the cbd_bufaddr field. Since this field is only set during setup(), the first i2c transaction would work and the following would send data read from an arbitrary memory location. Fixes: 61045dbe9d8d ("i2c: Add support for I2C bus on Freescale CPM1/CPM2 controllers") Signed-off-by: Nicolas VINCENT <nicolas.vincent@vossloh.com> Acked-by: Jochen Friedrich <jochen@scram.de> Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-09-21i2c: i801: Exclude device from suspend direct complete optimizationJean Delvare
By default, PCI drivers with runtime PM enabled will skip the calls to suspend and resume on system PM. For this driver, we don't want that, as we need to perform additional steps for system PM to work properly on all systems. So instruct the PM core to not skip these calls. Fixes: a9c8088c7988 ("i2c: i801: Don't restore config registers on runtime PM") Reported-by: Volker Rümelin <volker.ruemelin@googlemail.com> Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: stable@vger.kernel.org Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-09-18i2c: mxs: use MXS_DMA_CTRL_WAIT4END instead of DMA_CTRL_ACKMatthias Schiffer
The driver-specific usage of the DMA_CTRL_ACK flag was replaced with a custom flag in commit ceeeb99cd821 ("dmaengine: mxs: rename custom flag"), but i2c-mxs was not updated to use the new flag, completely breaking I2C transactions using DMA. Fixes: ceeeb99cd821 ("dmaengine: mxs: rename custom flag") Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-09-18i2c: mediatek: Send i2c master code at more than 1MHzQii Wang
The master code needs to being sent when the speed is more than I2C_MAX_FAST_MODE_PLUS_FREQ, not I2C_MAX_FAST_MODE_FREQ in the latest I2C-bus specification and user manual. Signed-off-by: Qii Wang <qii.wang@mediatek.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-09-18i2c: mediatek: Fix generic definitions for bus frequencyQii Wang
The max frequency of mediatek i2c controller driver is I2C_MAX_HIGH_SPEED_MODE_FREQ, not I2C_MAX_FAST_MODE_PLUS_FREQ. Fix it. Fixes: 90224e6468e1 ("i2c: drivers: Use generic definitions for bus frequencies") Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Qii Wang <qii.wang@mediatek.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-09-17i2c: core: Call i2c_acpi_install_space_handler() before ↵Hans de Goede
i2c_acpi_register_devices() Some ACPI i2c-devices _STA method (which is used to detect if the device is present) use autodetection code which probes which device is present over i2c. This requires the I2C ACPI OpRegion handler to be registered before we enumerate i2c-clients under the i2c-adapter. This fixes the i2c touchpad on the Lenovo ThinkBook 14-IIL and ThinkBook 15 IIL not getting an i2c-client instantiated and thus not working. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1842039 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-09-14i2c: i801: Simplify the suspend callbackJean Delvare
We don't actually need to derive the PCI device from the device structure, as we already have a pointer to it in our private data structure. Signed-off-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-09-14i2c: i801: Fix resume bugVolker Rümelin
On suspend the original host configuration gets restored. The resume routine has to undo this, otherwise the SMBus master may be left in disabled state or in i2c mode. [JD: Rebased on v5.8, moved the write into i801_setup_hstcfg.] Signed-off-by: Volker Rümelin <vr_qemu@t-online.de> Signed-off-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@kernel.org> Cc: stable@vger.kernel.org
2020-09-14i2c: aspeed: Mask IRQ status to relevant bitsEddie James
Mask the IRQ status to only the bits that the driver checks. This prevents excessive driver warnings when operating in slave mode when additional bits are set that the driver doesn't handle. Signed-off-by: Eddie James <eajames@linux.ibm.com> Reviewed-by: Tao Ren <rentao.bupt@gmail.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-09-09i2c: algo: pca: Reapply i2c bus settings after resetEvan Nimmo
If something goes wrong (such as the SCL being stuck low) then we need to reset the PCA chip. The issue with this is that on reset we lose all config settings and the chip ends up in a disabled state which results in a lock up/high CPU usage. We need to re-apply any configuration that had previously been set and re-enable the chip. Signed-off-by: Evan Nimmo <evan.nimmo@alliedtelesis.co.nz> Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-09-08i2c: npcm7xx: Fix timeout calculationTali Perry
timeout_usec value calculation was wrong, the calculated value was in msec instead of usec. Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver") Signed-off-by: Tali Perry <tali.perry1@gmail.com> Reviewed-by: Avi Fishman <avifishman70@gmail.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Alex Qiu <xqiu@google.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-29Merge branch 'i2c/for-current' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c fixes from Wolfram Sang: "A core fix for ACPI matching and two driver bugfixes" * 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: iproc: Fix shifting 31 bits i2c: rcar: in slave mode, clear NACK earlier i2c: acpi: Remove dead code, i.e. i2c_acpi_match_device() i2c: core: Don't fail PRP0001 enumeration when no ID table exist
2020-08-25i2c: iproc: Fix shifting 31 bitsRay Jui
Fix undefined behaviour in the iProc I2C driver by using 'BIT' marcro. Reported-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Ray Jui <ray.jui@broadcom.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> [wsa: in commit msg, don't say 'checkpatch' but name the issue] Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-25i2c: rcar: in slave mode, clear NACK earlierWolfram Sang
Currently, a NACK in slave mode is set/cleared when SCL is held low by the IP core right before the bit is about to be pushed out. This is too late for clearing and then a NACK from the previous byte is still used for the current one. Now, let's clear the NACK right after we detected the STOP condition following the NACK. Fixes: de20d1857dd6 ("i2c: rcar: add slave support") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-25i2c: acpi: Remove dead code, i.e. i2c_acpi_match_device()Andy Shevchenko
We have no users of i2c_acpi_match_device() anymore and seems will not have them in the future, thus remove dead code. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-25i2c: core: Don't fail PRP0001 enumeration when no ID table existAndy Shevchenko
When commit c64ffff7a9d1 ("i2c: core: Allow empty id_table in ACPI case as well") fixed the enumeration of I²C devices on ACPI enabled platforms when driver has no ID table, it missed the PRP0001 support. i2c_device_match() and i2c_acpi_match_device() differently match driver against given device. Use acpi_driver_match_device(), that is used in the former, in i2c_device_probe() and don't fail PRP0001 enumeration when no ID table exist. Fixes: c64ffff7a9d1 ("i2c: core: Allow empty id_table in ACPI case as well") BugLink: https://stackoverflow.com/q/63519678/2511795 Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-23treewide: Use fallthrough pseudo-keywordGustavo A. R. Silva
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2020-08-15Merge tag 'acpi-5.9-rc1-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull more ACPI updates from Rafael Wysocki: "Add new hardware support to the ACPI driver for AMD SoCs, the x86 clk driver and the Designware i2c driver (changes from Akshu Agrawal and Pu Wen)" * tag 'acpi-5.9-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: clk: x86: Support RV architecture ACPI: APD: Add a fmw property is_raven clk: x86: Change name from ST to FCH ACPI: APD: Change name from ST to FCH i2c: designware: Add device HID for Hygon I2C controller
2020-08-13Merge branch 'i2c/for-5.9' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c updates from Wolfram Sang: - bus recovery can now be given a pinctrl handle and the I2C core will do all the steps to switch to/from GPIO which can save quite some boilerplate code from drivers - "fallthrough" conversion - driver updates, mostly ID additions * 'i2c/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (32 commits) i2c: iproc: fix race between client unreg and isr i2c: eg20t: use generic power management i2c: eg20t: Drop PCI wakeup calls from .suspend/.resume i2c: mediatek: Fix i2c_spec_values description i2c: mediatek: Add i2c compatible for MediaTek MT8192 dt-bindings: i2c: update bindings for MT8192 SoC i2c: mediatek: Add access to more than 8GB dram in i2c driver i2c: mediatek: Add apdma sync in i2c driver i2c: i801: Add support for Intel Tiger Lake PCH-H i2c: i801: Add support for Intel Emmitsburg PCH i2c: bcm2835: Replace HTTP links with HTTPS ones Documentation: i2c: dev: 'block process call' is supported i2c: at91: Move to generic GPIO bus recovery i2c: core: treat EPROBE_DEFER when acquiring SCL/SDA GPIOs i2c: core: add generic I2C GPIO recovery dt-bindings: i2c: add generic properties for GPIO bus recovery i2c: rcar: avoid race when unregistering slave i2c: tegra: Avoid tegra_i2c_init_dma() for Tegra210 vi i2c i2c: tegra: Fix runtime resume to re-init VI I2C i2c: tegra: Fix the error path in tegra_i2c_runtime_resume ...
2020-08-12i2c: iproc: fix race between client unreg and isrDhananjay Phadke
When i2c client unregisters, synchronize irq before setting iproc_i2c->slave to NULL. (1) disable_irq() (2) Mask event enable bits in control reg (3) Erase slave address (avoid further writes to rx fifo) (4) Flush tx and rx FIFOs (5) Clear pending event (interrupt) bits in status reg (6) enable_irq() (7) Set client pointer to NULL Unable to handle kernel NULL pointer dereference at virtual address 0000000000000318 [ 371.020421] pc : bcm_iproc_i2c_isr+0x530/0x11f0 [ 371.025098] lr : __handle_irq_event_percpu+0x6c/0x170 [ 371.030309] sp : ffff800010003e40 [ 371.033727] x29: ffff800010003e40 x28: 0000000000000060 [ 371.039206] x27: ffff800010ca9de0 x26: ffff800010f895df [ 371.044686] x25: ffff800010f18888 x24: ffff0008f7ff3600 [ 371.050165] x23: 0000000000000003 x22: 0000000001600000 [ 371.055645] x21: ffff800010f18888 x20: 0000000001600000 [ 371.061124] x19: ffff0008f726f080 x18: 0000000000000000 [ 371.066603] x17: 0000000000000000 x16: 0000000000000000 [ 371.072082] x15: 0000000000000000 x14: 0000000000000000 [ 371.077561] x13: 0000000000000000 x12: 0000000000000001 [ 371.083040] x11: 0000000000000000 x10: 0000000000000040 [ 371.088519] x9 : ffff800010f317c8 x8 : ffff800010f317c0 [ 371.093999] x7 : ffff0008f805b3b0 x6 : 0000000000000000 [ 371.099478] x5 : ffff0008f7ff36a4 x4 : ffff8008ee43d000 [ 371.104957] x3 : 0000000000000000 x2 : ffff8000107d64c0 [ 371.110436] x1 : 00000000c00000af x0 : 0000000000000000 [ 371.115916] Call trace: [ 371.118439] bcm_iproc_i2c_isr+0x530/0x11f0 [ 371.122754] __handle_irq_event_percpu+0x6c/0x170 [ 371.127606] handle_irq_event_percpu+0x34/0x88 [ 371.132189] handle_irq_event+0x40/0x120 [ 371.136234] handle_fasteoi_irq+0xcc/0x1a0 [ 371.140459] generic_handle_irq+0x24/0x38 [ 371.144594] __handle_domain_irq+0x60/0xb8 [ 371.148820] gic_handle_irq+0xc0/0x158 [ 371.152687] el1_irq+0xb8/0x140 [ 371.155927] arch_cpu_idle+0x10/0x18 [ 371.159615] do_idle+0x204/0x290 [ 371.162943] cpu_startup_entry+0x24/0x60 [ 371.166990] rest_init+0xb0/0xbc [ 371.170322] arch_call_rest_init+0xc/0x14 [ 371.174458] start_kernel+0x404/0x430 Fixes: c245d94ed106 ("i2c: iproc: Add multi byte read-write support for slave mode") Signed-off-by: Dhananjay Phadke <dphadke@linux.microsoft.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-10i2c: eg20t: use generic power managementVaibhav Gupta
Drivers using legacy power management .suspen()/.resume() callbacks have to manage PCI states and device's PM states themselves. They also need to take care of standard configuration registers. Switch to generic power management framework using a single "struct dev_pm_ops" variable to take the unnecessary load from the driver. This also avoids the need for the driver to directly call most of the PCI helper functions and device power state control functions, as through the generic framework PCI Core takes care of the necessary operations, and drivers are required to do only device-specific jobs. Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com> Reviewed-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-10i2c: eg20t: Drop PCI wakeup calls from .suspend/.resumeVaibhav Gupta
The driver calls pci_enable_wake(...., false) in pch_i2c_suspend() as well as pch_i2c_resume(). Either it should enable-wake the device in .suspend() or should not invoke pci_enable_wake() at all. Concluding that this driver doesn't support enable-wake and PCI core calls pci_enable_wake(pci_dev, PCI_D0, false) during resume, drop it from .suspend() and .resume(). Reported-by: Bjorn Helgaas <helgaas@kernel.org> Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com> Reviewed-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-10i2c: mediatek: Fix i2c_spec_values descriptionMatthias Brugger
The struct i2c_spec_values have it's members documented but is missing the starting '@', which leads to warings like: drivers/i2c/busses/i2c-mt65xx.c:267: warning: Function parameter or member 'min_low_ns' not described in 'i2c_spec_values' We also delete min_high_ns member as it is not used in the code. Signed-off-by: Matthias Brugger <mbrugger@suse.com> Reviewed-by: Qii Wang <qii.wang@mediatek.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-07i2c: designware: Add device HID for Hygon I2C controllerPu Wen
Add device HID HYGO0010 to match the Hygon ACPI Vendor ID (HYGO) that was registered in http://www.uefi.org/acpi_id_list, and the I2C controller on Hygon paltform will use the HID. Signed-off-by: Pu Wen <puwen@hygon.cn> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-08-05i2c: mediatek: Add i2c compatible for MediaTek MT8192Qii Wang
Add i2c compatible for MT8192. Compare to MT8183 i2c controller, MT8192 support more then 8GB DMA mode. Signed-off-by: Qii Wang <qii.wang@mediatek.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: mediatek: Add access to more than 8GB dram in i2c driverQii Wang
Newer MTK chip support more than 8GB of dram. Replace support_33bits with more general dma_max_support and remove mtk_i2c_set_4g_mode. Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com> Signed-off-by: Qii Wang <qii.wang@mediatek.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: mediatek: Add apdma sync in i2c driverQii Wang
With the apdma remove hand-shake signal, it need to keep i2c and apdma in sync manually. Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: Qii Wang <qii.wang@mediatek.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: i801: Add support for Intel Tiger Lake PCH-HJarkko Nikula
Add SMBus PCI ID on Intel Tiger Lake PCH-H. Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: i801: Add support for Intel Emmitsburg PCHMika Westerberg
Add support for SMBus controller on Intel Emmitsburg PCH. This is the same IP as used in Cannon Lake and derivatives. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: bcm2835: Replace HTTP links with HTTPS onesAlexander A. Klimov
Rationale: Reduces attack surface on kernel devs opening the links for MITM as HTTPS traffic is much harder to manipulate. Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de> [wsa: shortened commit message] Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: at91: Move to generic GPIO bus recoveryCodrin Ciubotariu
Make the Microchip at91 driver the first to use the generic GPIO bus recovery support from the I2C core and discard the driver implementation. Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: core: treat EPROBE_DEFER when acquiring SCL/SDA GPIOsCodrin Ciubotariu
Even if I2C bus GPIO recovery is optional, devm_gpiod_get() can return -EPROBE_DEFER, so we should at least treat that. This ends up with i2c_register_adapter() to be able to return -EPROBE_DEFER. Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-05i2c: core: add generic I2C GPIO recoveryCodrin Ciubotariu
Multiple I2C bus drivers use similar bindings to obtain information needed for I2C recovery. For example, for platforms using device-tree, the properties look something like this: &i2c { ... pinctrl-names = "default", "gpio"; pinctrl-0 = <&pinctrl_i2c_default>; pinctrl-1 = <&pinctrl_i2c_gpio>; sda-gpios = <&pio 0 GPIO_ACTIVE_HIGH>; scl-gpios = <&pio 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; ... } For this reason, we can add this common initialization in the core. This way, other I2C bus drivers will be able to support GPIO recovery just by providing a pointer to platform's pinctrl and calling i2c_recover_bus() when SDA is stuck low. Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> [wsa: inverted one logic for better readability, minor update to kdoc] Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-08-04Merge tag 'uninit-macro-v5.9-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux Pull uninitialized_var() macro removal from Kees Cook: "This is long overdue, and has hidden too many bugs over the years. The series has several "by hand" fixes, and then a trivial treewide replacement. - Clean up non-trivial uses of uninitialized_var() - Update documentation and checkpatch for uninitialized_var() removal - Treewide removal of uninitialized_var()" * tag 'uninit-macro-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: compiler: Remove uninitialized_var() macro treewide: Remove uninitialized_var() usage checkpatch: Remove awareness of uninitialized_var() macro mm/debug_vm_pgtable: Remove uninitialized_var() usage f2fs: Eliminate usage of uninitialized_var() macro media: sur40: Remove uninitialized_var() usage KVM: PPC: Book3S PR: Remove uninitialized_var() usage clk: spear: Remove uninitialized_var() usage clk: st: Remove uninitialized_var() usage spi: davinci: Remove uninitialized_var() usage ide: Remove uninitialized_var() usage rtlwifi: rtl8192cu: Remove uninitialized_var() usage b43: Remove uninitialized_var() usage drbd: Remove uninitialized_var() usage x86/mm/numa: Remove uninitialized_var() usage docs: deprecated.rst: Add uninitialized_var()
2020-08-03Merge tag 'arm-drivers-5.9' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC driver updates from Arnd Bergmann: "A couple of subsystems have their own subsystem maintainers but choose to have the code merged through the soc tree as upstream, as the code tends to be used across multiple SoCs or has SoC specific drivers itself: - memory controllers: Krzysztof Kozlowski takes ownership of the drivers/memory subsystem and its drivers, starting out with a set of cleanup patches. A larger driver for the Tegra memory controller that was accidentally missed for v5.8 is now added. - reset controllers: Only minor updates to drivers/reset this time - firmware: The "turris mox" firmware driver gains support for signed firmware blobs The tegra firmware driver gets extended to export some debug information Various updates to i.MX firmware drivers, mostly cosmetic - ARM SCMI/SCPI: A new mechanism for platform notifications is added, among a number of minor changes. - optee: Probing of the TEE bus is rewritten to better support detection of devices that depend on the tee-supplicant user space. A new firmware based trusted platform module (fTPM) driver is added based on OP-TEE - SoC attributes: A new driver is added to provide a generic soc_device for identifying a machine through the SMCCC ARCH_SOC_ID firmware interface rather than by probing SoC family specific registers. The series also contains some cleanups to the common soc_device code. There are also a number of updates to SoC specific drivers, the main ones are: - Mediatek cmdq driver gains a few in-kernel interfaces - Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding support for additional SoC variants - The Qualcomm GENI core code gains interconnect path voting and performance level support, and integrating this into a number of device drivers. - A new driver for Samsung Exynos5800 voltage coupler for - Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC specific device drivers - Updates to the TI K3 Ring Accelerator driver" * tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits) soc: qcom: geni: Fix unused label warning soc: qcom: smd-rpm: Fix kerneldoc memory: jz4780_nemc: Only request IO memory the driver will use soc: qcom: pdr: Reorder the PD state indication ack MAINTAINERS: Add Git repository for memory controller drivers memory: brcmstb_dpfe: Fix language typo memory: samsung: exynos5422-dmc: Correct white space issues memory: samsung: exynos-srom: Correct alignment memory: pl172: Enclose macro argument usage in parenthesis memory: of: Correct kerneldoc memory: omap-gpmc: Fix language typo memory: omap-gpmc: Correct white space issues memory: omap-gpmc: Use 'unsigned int' for consistency memory: omap-gpmc: Enclose macro argument usage in parenthesis memory: omap-gpmc: Correct kerneldoc memory: mvebu-devbus: Align with open parenthesis memory: mvebu-devbus: Add missing braces to all arms of if statement memory: bt1-l2-ctl: Add blank lines after declarations soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static firmware: ti_sci: Replace HTTP links with HTTPS ones ...
2020-08-03Merge tag 'rm-unicore32' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rppt/linux Pull unicore32 removal from Mike Rapoport: "Remove unicore32 support. The unicore32 port do not seem maintained for a long time now, there is no upstream toolchain that can create unicore32 binaries and all the links to prebuilt toolchains for unicore32 are dead. Even compilers that were available are not supported by the kernel anymore. Guenter Roeck says: "I have stopped building unicore32 images since v4.19 since there is no available compiler that is still supported by the kernel. I am surprised that support for it has not been removed from the kernel" However, it's worth pointing out two things: - Guan Xuetao is still listed as maintainer and asked for the port to be kept around the last time Arnd suggested removing it two years ago. He promised that there would be compiler sources (presumably llvm), but has not made those available since. - https://github.com/gxt has patches to linux-4.9 and qemu-2.7, both released in 2016, with patches dated early 2019. These patches mainly restore a syscall ABI that was never part of mainline Linux but apparently used in production. qemu-2.8 removed support for that ABI and newer kernels (4.19+) can no longer be built with the old toolchain, so apparently there will not be any future updates to that git tree" * tag 'rm-unicore32' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/linux: MAINTAINERS: remove "PKUNITY SOC DRIVERS" entry rtc: remove fb-puv3 driver video: fbdev: remove fb-puv3 driver pwm: remove pwm-puv3 driver input: i8042: remove support for 8042-unicore32io i2c/buses: remove i2c-puv3 driver cpufreq: remove unicore32 driver arch: remove unicore32 port
2020-07-31i2c: rcar: avoid race when unregistering slaveWolfram Sang
Due to the lockless design of the driver, it is theoretically possible to access a NULL pointer, if a slave interrupt was running while we were unregistering the slave. To make this rock solid, disable the interrupt for a short time while we are clearing the interrupt_enable register. This patch is purely based on code inspection. The OOPS is super-hard to trigger because clearing SAR (the address) makes interrupts even more unlikely to happen as well. While here, reinit SCR to SDBS because this bit should always be set according to documentation. There is no effect, though, because the interface is disabled. Fixes: 7b814d852af6 ("i2c: rcar: avoid race when unregistering slave client") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-31Merge tag 'v5.8-rc7' into i2c/for-5.9Wolfram Sang
2020-07-28i2c: slave: add sanity check when unregisteringWolfram Sang
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Alain Volmat <alain.volmat@st.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-28i2c: slave: improve sanity check when registeringWolfram Sang
Add check for ERR_PTR and simplify code while here. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Alain Volmat <alain.volmat@st.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-28i2c: tegra: Avoid tegra_i2c_init_dma() for Tegra210 vi i2cSowjanya Komatineni
VI I2C is on host1x bus so APB DMA can't be used for Tegra210 VI I2C and there are no tx and rx dma channels for VI I2C. So, avoid attempt of requesting DMA channels. Reviewed-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-28i2c: tegra: Fix runtime resume to re-init VI I2CSowjanya Komatineni
VI I2C is on host1x bus and is part of VE power domain. During suspend/resume VE power domain goes through power off/on. So, controller reset followed by i2c re-initialization is required after the domain power up. This patch fixes it. Reviewed-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-28i2c: tegra: Fix the error path in tegra_i2c_runtime_resumeSowjanya Komatineni
tegra_i2c_runtime_resume does not disable prior enabled clocks properly. This patch fixes it. Reviewed-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-28i2c: tegra: Remove NULL pointer check before ↵Sowjanya Komatineni
clk_enable/disable/prepare/unprepare clk_enable, clk_disable, clk_prepare, and clk_unprepare APIs have implementation for checking clk pointer not NULL and clock consumers can safely call these APIs without NULL pointer check. So, this patch cleans up Tegra i2c driver to remove explicit checks before these APIs. Reviewed-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-28i2c: tegra: Don't mark VI I2C as IRQ safe runtime PMSowjanya Komatineni
Tegra VI I2C is part of VE power domain and typically used for camera usecases. VE power domain is not always on and is non-IRQ safe. So, IRQ safe device cannot be attached to a non-IRQ safe domain as it prevents powering off the PM domain and generic power domain driver will warn. Current driver marks all I2C devices as IRQ safe and VI I2C device does not require IRQ safe as it will not be used for atomic transfers. This patch has fix to make VI I2C as non-IRQ safe. Reviewed-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-27i2c: core: do not use logical device when creating irq domainWolfram Sang
Let's rather use its physical parent device to give proper namings and connections in debugfs. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-26i2c: rcar: slave: only send STOP event when we have been addressedWolfram Sang
When the SSR interrupt is activated, it will detect every STOP condition on the bus, not only the ones after we have been addressed. So, enable this interrupt only after we have been addressed, and disable it otherwise. Fixes: de20d1857dd6 ("i2c: rcar: add slave support") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-24i2c: revert "i2c: core: Allow drivers to disable i2c-core irq mapping"Wolfram Sang
This manually reverts commit d1d84bb95364ed604015c2b788caaf3dbca0262f. The only user has gone two years ago with commit 589edb56b424 ("ACPI / scan: Create platform device for INT33FE ACPI nodes") and no new user has showed up. Remove and hope we will never need it again. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2020-07-24i2c: fsi: Prevent adding adapters for ports without dts nodesEddie James
Ports should be defined in the devicetree if they are to be enabled on the system. Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Wolfram Sang <wsa@kernel.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-05 00:29:22 +0000