| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm driver updates for v5.9
For RPMh this fixes an issue where ktime was used during suspend, allows
the driver to be used on ARM targets and some minor cleanups.
It adds support for the latest format version in the socinfo driver and
adds identifiers for SM8250 and SDM630.
SMD-RPM gains compatibles for MSM8994 and MSM8936 and the Qualcomm SCM
gains compatibles MSM8994 and IPQ8074.
The GENI core code gains interconnect path voting and performance level
support, with subsequent patches integrating this with the SPI, I2C,
UART and QSPI drivers.
Following this the KGDB support for the GENI serial driver is improved,
the performance related to chip-select is improved for SPI and QSPI.
* tag 'qcom-drivers-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (35 commits)
soc: qcom: geni: Fix NULL pointer dereference
tty: serial: qcom-geni-serial: Drop the icc bw votes in suspend for console
serial: qcom_geni_serial: Always use 4 bytes per TX FIFO word
serial: qcom_geni_serial: Make kgdb work even if UART isn't console
spi: spi-geni-qcom: Get rid of most overhead in prepare_message()
spi: spi-geni-qcom: Set the clock properly at runtime resume
spi: spi-geni-qcom: Avoid clock setting if not needed
spi: spi-qcom-qspi: Set an autosuspend delay of 250 ms
spi: spi-qcom-qspi: Avoid clock setting if not needed
spi: spi-qcom-qspi: Use OPP API to set clk/perf state
firmware: qcom_scm: Add msm8994 compatible
firmware: qcom_scm: Fix legacy convention SCM accessors
<linux/of.h>: add stub for of_get_next_parent() to fix qcom build error
dt-bindings: firmware: qcom: Add compatible for IPQ8074 SoC
spi: spi-geni-qcom: Use OPP API to set clk/perf state
tty: serial: qcom_geni_serial: Use OPP API to set clk/perf state
spi: spi-qcom-qspi: Add interconnect support
spi: spi-geni-qcom: Add interconnect support
spi: spi-geni-qcom: Combine the clock setting code
tty: serial: qcom_geni_serial: Add interconnect support
...
Link: https://lore.kernel.org/r/20200721044812.3429652-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
There are few issues on Zynq SOC observed in the stress tests causing
timeout errors. Even though all the data is received, timeout error
is thrown. This is due to an IP bug in which the COMP bit in ISR is
not set at end of transfer and completion interrupt is not generated.
This bug is seen on Zynq platforms when the following condition occurs:
Master read & HOLD bit set & Transfer size register reaches '0'.
One workaround is to clear the HOLD bit before the transfer size
register reaches '0'. The current implementation checks for this at
the start of the loop and also only for less than FIFO DEPTH case
(ignoring the equal to case).
So clear the HOLD bit when the data yet to receive is less than or
equal to the FIFO DEPTH. This avoids the IP bug condition.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
This reverts commit d358def706880defa4c9e87381c5bf086a97d5f9.
There are two issues with "i2c: cadence: Fix the hold bit setting" commit.
1. In case of combined message request from user space, when the HOLD
bit is cleared in cdns_i2c_mrecv function, a STOP condition is sent
on the bus even before the last message is started. This is because when
the HOLD bit is cleared, the FIFOS are empty and there is no pending
transfer. The STOP condition should occur only after the last message
is completed.
2. The code added by the commit is redundant. Driver is handling the
setting/clearing of HOLD bit in right way before the commit.
The setting of HOLD bit based on 'bus_hold_flag' is taken care in
cdns_i2c_master_xfer function even before cdns_i2c_msend/cdns_i2c_recv
functions.
The clearing of HOLD bit is taken care at the end of cdns_i2c_msend and
cdns_i2c_recv functions based on bus_hold_flag and byte count.
Since clearing of HOLD bit is done after the slave address is written to
the register (writing to address register triggers the message transfer),
it is ensured that STOP condition occurs at the right time after
completion of the pending transfer (last message).
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
Enable i2c transactions in irq disabled contexts like poweroff where the
PMIC is connected via i2c.
Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Modules with multiple authors should use multiple MODULE_AUTHOR()
statements according to comment in include/linux/module.h.
Split the i2c modules with multiple authors to use multiple
MODULE_AUTHOR() statements.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
I2C_SMBUS_BLOCK_MAX defines already the maximum number as defined in the
SMBus 2.0 specs. I don't see a reason to add 1 here. Also, fix the errno
to what is suggested for this error.
Fixes: c9bfdc7c16cb ("i2c: mlxcpld: Add support for smbus block read transaction")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Michael Shych <michaelsh@mellanox.com>
Tested-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
I can't recall why there was none, but we surely want to have it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Add more details which have either been missing ever since or describe
recent additions.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The driver can't be loaded automatically because it misses
module alias to be provided. Add corresponding MODULE_DEVICE_TABLE()
call to the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Current AMD's zen-based APUs use this core for some of its i2c-buses.
With this patch we re-enable autodetection of hwmon-alike devices, so
lm-sensors will be able to work automatically.
It does not affect the boot-time of embedded devices, as the class is
set based on the DMI information.
DMI is probed only on Qtechnology QT5222 Industrial Camera Platform.
DocLink: https://qtec.com/camera-technology-camera-platforms/
Fixes: 3eddad96c439 ("i2c: designware: reverts "i2c: designware: Add support for AMD I2C controller"")
Signed-off-by: Ricardo Ribalda <ribalda@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The PCA9665 datasheet says that I2CSTA = 78h indicates that SCL is stuck
low, this differs to the PCA9564 which uses 90h for this indication.
Treat either 0x78 or 0x90 as an indication that the SCL line is stuck.
Based on looking through the PCA9564 and PCA9665 datasheets this should
be safe for both chips. The PCA9564 should not return 0x78 for any valid
state and the PCA9665 should not return 0x90.
Fixes: eff9ec95efaa ("i2c-algo-pca: Add PCA9665 support")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The unicore32 port is removed from the kernel.
There is no point to keep stale i2c bus driver for this architecture.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
|
|
If the i2c bus driver ignores the I2C_M_RECV_LEN flag (as some of
them do), it is possible for an I2C_SMBUS_BLOCK_DATA read issued
on some random device to return an arbitrary value in the first
byte (and nothing else). When this happens, i2c_smbus_xfer_emulated()
will happily write past the end of the supplied data buffer, thus
causing Bad Things to happen. To prevent this, check the size
before copying the data block and return an error if it is too large.
Fixes: 209d27c3b167 ("i2c: Emulate SMBus block read over I2C")
Signed-off-by: Mans Rullgard <mans@mansr.com>
[wsa: use better errno]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The port number field in the status register was not correct, so fix it.
Fixes: d6ffb6300116 ("i2c: Add FSI-attached I2C master algorithm")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Get the interconnect paths for I2C based Serial Engine device
and vote according to the bus speed of the driver.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/1592908737-7068-4-git-send-email-akashast@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
John Stultz reported that commit f9288fcc5c615 ("i2c: designware: Move
ACPI parts into common module") caused a regression on the HiKey board
where adv7511 HDMI bridge driver wasn't probing anymore due the I2C bus
failed to start.
It seems the change caused the bus speed being zero when CONFIG_ACPI
not set and neither speed based on "clock-frequency" device property
or default fast mode is set.
Fix this by splitting i2c_dw_acpi_adjust_bus_speed() to
i2c_dw_acpi_round_bus_speed() and i2c_dw_adjust_bus_speed(), where
the latter one has the code that runs independently of ACPI.
Fixes: f9288fcc5c615 ("i2c: designware: Move ACPI parts into common module")
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Fix spelling mistake in the comments with help of `codespell`.
seperate ==> separate
Signed-off-by: Keyur Patel <iamkeyur96@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
All in-tree users have been converted to the new i2c_new_client_device
function, so remove this deprecated one.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- fix build rules in binderfs sample
- fix build errors when Kbuild recurses to the top Makefile
- covert '---help---' in Kconfig to 'help'
* tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
treewide: replace '---help---' in Kconfig files with 'help'
kbuild: fix broken builds because of GZIP,BZIP2,LZOP variables
samples: binderfs: really compile this sample and fix build issues
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C has quite some patches for you this time. I hope it is the move to
per-driver-maintainers which is now showing results. We will see.
The big news is two new drivers (Nuvoton NPCM and Qualcomm CCI),
larger refactoring of the Designware, Tegra, and PXA drivers, the
Cadence driver supports being a slave now, and there is support to
instanciate SPD eeproms for well-known cases (which will be
user-visible because the i801 driver supports it), and some
devm_platform_ioremap_resource() conversions which blow up the
diffstat.
Note that I applied the Nuvoton driver quite late, so some minor fixup
patches arrived during the merge window. I chose to apply them right
away because they were trivial"
* 'i2c/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (109 commits)
i2c: Drop stray comma in MODULE_AUTHOR statements
i2c: npcm7xx: npcm_i2caddr[] can be static
MAINTAINERS: npcm7xx: Add maintainer for Nuvoton NPCM BMC
i2c: npcm7xx: Fix a couple of error codes in probe
i2c: icy: Fix build with CONFIG_AMIGA_PCMCIA=n
i2c: npcm7xx: Remove unnecessary parentheses
i2c: npcm7xx: Add support for slave mode for Nuvoton
i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver
dt-bindings: i2c: npcm7xx: add NPCM I2C controller
i2c: pxa: don't error out if there's no pinctrl
i2c: add 'single-master' property to generic bindings
i2c: designware: Add Baikal-T1 System I2C support
i2c: designware: Move reg-space remapping into a dedicated function
i2c: designware: Retrieve quirk flags as early as possible
i2c: designware: Convert driver to using regmap API
i2c: designware: Discard Cherry Trail model flag
i2c: designware: Add Baytrail sem config DW I2C platform dependency
i2c: designware: slave: Set DW I2C core module dependency
i2c: designware: Use `-y` to build multi-object modules
dt-bindings: i2c: dw: Add Baikal-T1 SoC I2C controller
...
|
|
Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
It is not the common usage to have a comma between the name and the
email address, so remove it.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Fixes: f54736925a4f ("i2c: npcm7xx: Add support for slave mode for Nuvoton")
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time around we have four lines of diff in the core framework,
removing a function that isn't used anymore. Otherwise the main new
thing for the common clk framework is that it is selectable in the
Kconfig language now. Hopefully this will let clk drivers and clk
consumers be testable on more than the architectures that support the
clk framework. The goal is to introduce some Kunit tests for the
framework.
Outside of the core framework we have the usual set of various driver
updates and non-critical fixes. The dirstat shows that the new
Baikal-T1 driver is the largest addition this time around in terms of
lines of code. After that the x86 (Intel), Qualcomm, and Mediatek
drivers introduce many lines to support new or upcoming SoCs. After
that the dirstat shows the usual suspects working on their SoC support
by fixing minor bugs, correcting data and converting some of their DT
bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix
clock support on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and
clk-pllv3 drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support
aarch32 mode on aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using
composite clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102
defined bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on
Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (155 commits)
clk: mediatek: Remove ifr{0,1}_cfg_regs structures
clk: baikal-t1: remove redundant assignment to variable 'divider'
clk: baikal-t1: fix spelling mistake "Uncompatible" -> "Incompatible"
dt-bindings: clock: Add a missing include to MMP Audio Clock binding
dt: Add bindings for IDT VersaClock 5P49V5925
clk: vc5: Add support for IDT VersaClock 5P49V6965
clk: Add Baikal-T1 CCU Dividers driver
clk: Add Baikal-T1 CCU PLLs driver
dt-bindings: clk: Add Baikal-T1 CCU Dividers binding
dt-bindings: clk: Add Baikal-T1 CCU PLLs binding
clk: mediatek: assign the initial value to clk_init_data of mtk_mux
clk: mediatek: Add MT6765 clock support
clk: mediatek: add mt6765 clock IDs
dt-bindings: clock: mediatek: document clk bindings vcodecsys for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings mipi0a for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings for Mediatek MT6765 SoC
CLK: HSDK: CGU: add support for 148.5MHz clock
CLK: HSDK: CGU: support PLL bypassing
CLK: HSDK: CGU: check if PLL is bypassed first
clk: clk-si5341: Add support for the Si5345 series
...
|
|
The code here is accidentally returning IS_ERR() which is 1 but it
should be returning negative error codes with PTR_ERR().
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
This has been found by the Kernel Test Robot:
http://lkml.iu.edu/hypermail/linux/kernel/2006.0/06862.html
With CONFIG_AMIGA_PCMCIA=n, io_mm.h does not pull in amigahw.h and
ZTWO_VADDR is undefined. Add forgotten include to i2c-icy.c
Fixes: 4768e90ecaec ("i2c: Add i2c-icy for I2C on m68k/Amiga")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Max Staudt <max@enpas.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Remove unnecessary parentheses around _bus_.
This issue was found with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.8 kernel cycle.
Core changes:
- A new GPIO aggregator driver has been merged: this can join a few
select GPIO lines into a new aggregated GPIO chip. This can be used
for security: a process can be granted access to only these lines,
for example for industrial control. Another way to use this is to
reexpose certain select lines to a virtual machine or container.
- Warn if the gpio-line-names is too long in he DT parser core.
- GPIO lines can now be looked up by line name in addition to being
looked up by offset.
New drivers:
- A new generic regmap GPIO driver has been merged. Too many regmap
drivers are starting to look like each other so we need to create
some common ground and try to move drivers over to using that.
- The F7188X driver now supports F81865.
Driver improvements:
- Large improvements to the PCA953x expander, get multiple lines and
several cleanups.
- Large improvements to the DesignWare DWAPB driver, and Sergey Semin
has volunteered to maintain it.
- PL061 can now be built as a module, this is part of a bigger effort
to make the ARM platforms more modular"
* tag 'gpio-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: pca953x: Drop unneeded ACPI_PTR()
MAINTAINERS: Add gpio regmap section
gpio: add a reusable generic gpio_chip using regmap
gpiolib: Introduce gpiochip_irqchip_add_domain()
gpio: gpiolib: Allow GPIO IRQs to lazy disable
gpiolib: Separate GPIO_GET_LINEINFO_WATCH_IOCTL conditional
gpio: rcar: Fix runtime PM imbalance on error
gpio: pca935x: Allow IRQ support for driver built as a module
gpio: pxa: Add COMPILE_TEST support
dt-bindings: gpio: Add renesas,em-gio bindings
MAINTAINERS: Fix file name for DesignWare GPIO DT schema
gpio: dwapb: Remove unneeded has_irq member in struct dwapb_port_property
gpio: dwapb: Don't use IRQ 0 as valid Linux interrupt
gpio: dwapb: avoid error message for optional IRQ
gpio: dwapb: Call acpi_gpiochip_free_interrupts() on GPIO chip de-registration
gpio: max730x: bring gpiochip_add_data after port config
MAINTAINERS: Add GPIO Aggregator section
docs: gpio: Add GPIO Aggregator documentation
gpio: Add GPIO Aggregator
gpiolib: Add support for GPIO lookup by line name
...
|
|
Add support for slave mode for Nuvoton
NPCM BMC I2C controller driver.
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Add Nuvoton NPCM BMC I2C controller driver.
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The bus recovery patch regresses on OLPC XO-1.75 that has no pinctrl in
its DT.
Fixes: 7c9ec2c52518 ("i2c: pxa: implement generic i2c bus recovery")'
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
* pm-core:
PM: runtime: Replace pm_runtime_callbacks_present()
PM: runtime: clk: Fix clk_pm_runtime_get() error path
PM: runtime: Make clear what we do when conditions are wrong in rpm_suspend()
* pm-sleep:
PM: hibernate: Restrict writes to the resume device
PM: hibernate: Split off snapshot dev option
PM: hibernate: Incorporate concurrency handling
PM: sleep: Helpful edits for devices.rst documentation
Documentation: PM: sleep: Update driver flags documentation
PM: sleep: core: Rename DPM_FLAG_LEAVE_SUSPENDED
PM: sleep: core: Rename DPM_FLAG_NEVER_SKIP
PM: sleep: core: Rename dev_pm_smart_suspend_and_suspended()
PM: sleep: core: Rename dev_pm_may_skip_resume()
PM: sleep: core: Rework the power.may_skip_resume handling
PM: sleep: core: Do not skip callbacks in the resume phase
PM: sleep: core: Fold functions into their callers
PM: sleep: core: Simplify the SMART_SUSPEND flag handling
|
|
Baikal-T1 System Controller is equipped with a dedicated I2C Controller
which functionality is based on the DW APB I2C IP-core, the only
difference in a way it' registers are accessed. There are three access
register provided in the System Controller registers map, which indirectly
address the normal DW APB I2C registers space. So in order to have the
Baikal-T1 System I2C Controller supported by the common DW APB I2C driver
we created a dedicated Dw I2C controller model quirk, which retrieves the
syscon regmap from the parental dt node and creates a new regmap based on
it.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
This is a preparation patch before adding a quirk with custom registers
map creation required for the Baikal-T1 System I2C support.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Some platforms might need to activate the driver quirks at a very early
probe stage. For instance, Baikal-T1 System I2C doesn't need to map the
registers space as ones belong to the system controller. Instead it will
request the syscon regmap from the parental DT node. In order to be able
to do so let's retrieve the model flags right after the DW I2C private
data is created. While at it replace the or-assignment with just
assignment operator since or-ing is redundant at this stage.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Seeing the DW I2C driver is using flags-based accessors with two
conditional clauses it would be better to replace them with the regmap
API IO methods and to initialize the regmap object with read/write
callbacks specific to the controller registers map implementation. This
will be also handy for the drivers with non-standard registers mapping
(like an embedded into the Baikal-T1 System Controller DW I2C block, which
glue-driver is a part of this series).
As before the driver tries to detect the mapping setup at probe stage and
creates a regmap object accordingly, which will be used by the rest of the
code to correctly access the controller registers. In two places it was
appropriate to convert the hand-written read-modify-write and
read-poll-loop design patterns to the corresponding regmap API
ready-to-use methods.
Note the regmap IO methods return value is checked only at the probe
stage. The rest of the code won't do this because basically we have
MMIO-based regmap so non of the read/write methods can fail (this also
won't be needed for the Baikal-T1-specific I2C controller).
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[wsa: fix type of 'rx_valid' and remove outdated kdoc var description]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
A PM workaround activated by the flag MODEL_CHERRYTRAIL has been removed
since commit 9cbeeca05049 ("i2c: designware: Remove Cherry Trail PMIC I2C
bus pm_disabled workaround"), but the flag most likely by mistake has been
left in the Dw I2C drivers. Let's remove it. Since MODEL_MSCC_OCELOT is
the only model-flag left, redefine it to be 0x100 so setting a very first
bit in the MODEL_MASK bits range.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Currently Intel Baytrail I2C semaphore is a feature of the DW APB I2C
platform driver. It's a bit confusing to see it's config in the menu at
some separated place with no reference to the platform code. Let's move the
config definition to be below the I2C_DESIGNWARE_PLATFORM config and mark
it with "depends on I2C_DESIGNWARE_PLATFORM" statement. By doing so the
config menu will display the feature right below the DW I2C platform
driver item and will indent it to the right so signifying its belonging.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
DW APB I2C slave code in fact depends on the DW I2C driver core, but not
on the platform code as it used to be before commit 90bc1ee6de9f ("i2c:
designware: Allow slave mode for PCI enumerated devices"). Yes, the I2C
slave interface is currently supported by both the platform and PCI
versions of the IP core, but it still depends on the DW I2C core
functionality and must be available only if the last one is enabled.
So make sure the DW APB I2C slave config is only available if the
I2C_DESIGNWARE_CORE config is enabled.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Since commit 4f8272802739 ("Documentation: update kbuild loadable modules
goals & examples") `-objs` is fitted for building host programs, lets
change DW I2C core, platform and PCI driver kbuild directives to using
`-y`, which more straightforward for device drivers. By doing so we can
discard the ifeq construction in favor to the more natural and less bulky
`<module>-$(CONFIG_X) += x.o`
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
This currently generates a warning:
drivers/i2c/busses/i2c-sh_mobile.c: In function 'sh_mobile_i2c_isr':
drivers/i2c/busses/i2c-sh_mobile.c:399:26: warning: 'data' may be used uninitialized in this function [-Wmaybe-uninitialized]
Though the code looks okay and shouldn't ever use the variable
uninitialized. Fix the warning by moving the code around and getting rid
of 'data'.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[wsa: minor updates to commit message]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Call the function to instantiate SPD EEPROMs automatically on the
main SMBus controller.
Multiplexed SMBus systems are excluded for now as they are more
complex to handle.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
In simple cases we can instantiate SPD EEPROMs on the SMBus
automatically. Start with just DDR2, DDR3 and DDR4 on x86 for now,
and only for systems with no more than 4 memory slots. These
limitations may be lifted later.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
[wsa: minor change for new API]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Support for 16-bit addresses has been added, so remove it from the todo
list. Also, in the introductory sentence, may clear we talk about "slave
IP cores" to make reading easier.
Fixes: 82d514815441 ("i2c-eeprom_slave: Add support for more eeprom models")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
We have a kzalloced struct, no need to init to 0.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
acpi_dev_get_resources() does perform the NULL pointer check against
ACPI companion device which is given as function parameter. Thus,
there is no need to duplicate this check in the caller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Linux 5.7-rc7
|
|
PTR_ERR_OR_ZERO contains if(IS_ERR(...)) + PTR_ERR.
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Reviewed-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
No need to populate a variable if it is used only in debug output which
may get compiled away anyhow.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
