| Age | Commit message (Collapse) | Author |
|---|
|
Add PCI ID for Intel Cedar Fork PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Sun, Yunying reported the following failure on Denverton micro-server:
EDAC DEBUG: pnd2_init:
EDAC DEBUG: pnd2_probe:
EDAC DEBUG: dnv_rd_reg: Read b_cr_tolud_pci=00000000_80000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_touud_lo_pci=00000000_80000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_touud_hi_pci=00000000_00000004
EDAC DEBUG: dnv_rd_reg: Read b_cr_asym_mem_region0_mchbar=00000000_00000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_asym_mem_region1_mchbar=00000000_00000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_mot_out_base_mchbar=00000000_00000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_mot_out_mask_mchbar=00000000_00000000
EDAC pnd2: Failed to register device with error -19.
On Denverton micro-server, the presence of the P2SB bridge PCI device is
enabled or disabled by the item 'RelaxSecConf' in BIOS setup menu. When
'RelaxSecConf' is enabled, the P2SB PCI device is present and the pnd2_edac
EDAC driver also uses it to get BAR. Hiding the P2SB PCI device caused the
pnd2_edac EDAC driver failed to get BAR then reported the above failure.
Therefor, store the presence state of P2SB PCI device before unhiding it
for reading BAR and restore the presence state after reading BAR.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Reported-by: Yunying Sun <yunying.sun@intel.com>
Tested-by: Yunying Sun <yunying.sun@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Added SMBUS PCI Ids for SMBUS for Cannon Lake PCH.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[jarkko.nikula@linux.intel.com: Add entries to Documentation and Kconfig.
Cover Cannon Lake-H too]
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Intel Gemini Lake has the same SMBus host controller than Intel Broxton.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The current SMBus Host Notify implementation relies on .alert() to
relay its notifications. However, the use cases where SMBus Host
Notify is needed currently is to signal data ready on touchpads.
This is closer to an IRQ than a custom API through .alert().
Given that the 2 touchpad manufacturers (Synaptics and Elan) that
use SMBus Host Notify don't put any data in the SMBus payload, the
concept actually matches one to one.
Benefits are multiple:
- simpler code and API: the client will just have an IRQ, and
nothing needs to be added in the adapter beside internally
enabling it.
- no more specific workqueue, the threading is handled by IRQ core
directly (when required)
- no more races when removing the device (the drivers are already
required to disable irq on remove)
- simpler handling for drivers: use plain regular IRQs
- no more dependency on i2c-smbus for i2c-i801 (and any other adapter)
- the IRQ domain is created automatically when the adapter exports
the Host Notify capability
- the IRQ are assign only if ACPI, OF and the caller did not assign
one already
- the domain is automatically destroyed on remove
- fewer lines of code (minus 20, yeah!)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
On the platform tested, reading SMBNTFDDAT always returns 0 (using 1 read
of a word or 2 of 2 bytes). Given that we are not sure why and that we
don't need to rely on the data parameter in the current users of Host
Notify, remove this part of the code.
If someone wants to re-enable it, just revert this commit and data should
be available.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
no functional changes
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
i801 mixes hexadecimal and decimal values for defining bits. However,
we have a nice BIT() macro for this exact purpose.
No functional changes, cleanup only.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
No functional changes, just typos and remove unused #define.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Also do not override any other configuration in this register.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Starting with the 8-Series/C220 PCH (Lynx Point), the SMBus
controller includes a SPD EEPROM protection mechanism. Once the SPD
Write Disable bit is set, only reads are allowed to slave addresses
0x50-0x57.
However the legacy implementation of I2C Block Read since the ICH5
looks like a write, and is therefore blocked by the SPD protection
mechanism. This causes the eeprom and at24 drivers to fail.
So assume that I2C Block Read is implemented as an actual read on
these chipsets. I tested it on my Q87 chipset and it seems to work
just fine.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: rebased to v4.9-rc2]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Here is the 4.9 pull request from I2C including:
- centralized error messages when registering to the core
- improved lockdep annotations to prevent false positives
- DT support for muxes, gates, and arbitrators
- bus speeds can now be obtained from ACPI
- i2c-octeon got refactored and now supports ThunderX SoCs, too
- i2c-tegra and i2c-designware got a bigger bunch of updates
- a couple of standard driver fixes and improvements"
* 'i2c/for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (71 commits)
i2c: axxia: disable clks in case of failure in probe
i2c: octeon: thunderx: Limit register access retries
i2c: uniphier-f: fix misdetection of incomplete STOP condition
gpio: pca953x: variable 'id' was used twice
i2c: i801: Add support for Kaby Lake PCH-H
gpio: pca953x: fix an incorrect lockdep warning
i2c: add a warning to i2c_adapter_depth()
lockdep: make MAX_LOCKDEP_SUBCLASSES unconditionally visible
i2c: export i2c_adapter_depth()
i2c: rk3x: Fix variable 'min_total_ns' unused warning
i2c: rk3x: Fix sparse warning
i2c / ACPI: Do not touch an I2C device if it belongs to another adapter
i2c: octeon: Fix high-level controller status check
i2c: octeon: Avoid sending STOP during recovery
i2c: octeon: Fix set SCL recovery function
i2c: rcar: add support for r8a7796 (R-Car M3-W)
i2c: imx: make bus recovery through pinctrl optional
i2c: meson: add gxbb compatible string
i2c: uniphier-f: set the adapter to master mode when probing
i2c: uniphier-f: avoid WARN_ON() of clk_disable() in failure path
...
|
|
ACPI WDAT table is the preferred way to use hardware watchdog over the
native iTCO_wdt. Windows only uses this table for its hardware watchdog
implementation so we should be relatively safe to trust it has been
validated by OEMs
Prevent iTCO watchdog creation if we detect that there is ACPI WDAT table.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Intel Kaby Lake PCH-H has the same legacy SMBus host controller than Intel
Sunrisepoint PCH. It also has same iTCO watchdog on the bus.
Add Kaby Lake PCH-H PCI ID to the list of supported devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The i801 chip can handle the Host Notify feature since ICH 3 as mentioned
in http://www.intel.com/content/dam/doc/datasheet/82801ca-io-controller-hub-3-datasheet.pdf
Enable the functionality unconditionally and propagate the alert
on each notification.
With a T440s and a Synaptics touchpad that implements Host Notify, the
payload data is always 0x0000, so I am not sure if the device actually
sends the payload or if there is a problem regarding the implementation.
Tested-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
On a CRC error while using hardware-supported PEC, an additional
error bit is set in the auxiliary status register. If this bit
isn't cleared, all subsequent operations will fail, essentially
hanging the controller.
The fix is simple: check, report, and clear the bit in
i801_check_post(). Also, in case the driver starts with the
hardware in that state, clear it in i801_check_pre() as well.
Signed-off-by: Ellen Wang <ellen@cumulusnetworks.com>
Tested-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The interrupt handling code makes it look like several status values
may be merged together before being processed, while this will never
happen. Change from bit-wise OR to simple assignment to make it more
obvious and avoid misunderstanding.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Many Intel systems the BIOS declares a SystemIO OpRegion below the SMBus
PCI device as can be seen in ACPI DSDT table from Lenovo Yoga 900:
Device (SBUS)
{
OperationRegion (SMBI, SystemIO, (SBAR << 0x05), 0x10)
Field (SMBI, ByteAcc, NoLock, Preserve)
{
HSTS, 8,
Offset (0x02),
HCON, 8,
HCOM, 8,
TXSA, 8,
DAT0, 8,
DAT1, 8,
HBDR, 8,
PECR, 8,
RXSA, 8,
SDAT, 16
}
There are also bunch of AML methods that that the BIOS can use to access
these fields. Most of the systems in question AML methods accessing the
SMBI OpRegion are never used.
Now, because of this SMBI OpRegion many systems fail to load the SMBus
driver with an error looking like one below:
ACPI Warning: SystemIO range 0x0000000000003040-0x000000000000305F
conflicts with OpRegion 0x0000000000003040-0x000000000000304F
(\_SB.PCI0.SBUS.SMBI) (20160108/utaddress-255)
ACPI: If an ACPI driver is available for this device, you should use
it instead of the native driver
The reason is that this SMBI OpRegion conflicts with the PCI BAR used by
the SMBus driver.
It turns out that we can install a custom SystemIO address space handler
for the SMBus device to intercept all accesses through that OpRegion. This
allows us to share the PCI BAR with the AML code if it for some reason is
using it. We do not expect that this OpRegion handler will ever be called
but if it is we print a warning and prevent all access from the SMBus
driver itself.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=110041
Reported-by: Andy Lutomirski <luto@kernel.org>
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org
|
|
Allow runtime PM so that PM and PCI core can put the device into low-power
state when idle and resume it back when needed in those platforms that
support PM for i801 device.
Enable also autosuspend with 1 second delay in order to not needlessly
toggle power state on and off if there are multiple transactions during
short time.
Device is resumed at the beginning of bus access and marked idle ready
for autosuspend at the end of it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Stop using legacy PCI PM support and convert to standard dev_pm_ops.
This provides more straightforward path to add runtime PM.
While at it remove explicit PCI power state control and configuration space
save/restore as the PCI core does it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Mostly usual driver updates and improvements. The changelog should
give an idea. Standing out is the i2c-qup driver with lots of new
capabilities and we also have now an i2c-demuxer.
I'd especially like to welcome Peter Rosin as the i2c-mux maintainer.
He has an interesting series for muxes in the queue and agreed to look
after this part of the subsystem. Thank you, Peter, and welcome
again!
The octeon changes were applied pretty recently before the merge
window. I am aware. They are the first (and relatively simple)
patches of a larger overhaul to this driver. In case something goes
wrong with them, they are easy to fix (or revert). The advantage I
see is that they are out of the way, and I can concentrate on the next
block of patches. I really would like to apply the overhaul in
smaller batches to avoid regressions. And waiting a cycle for the
introductory patches seemed too much of a delay for me"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (39 commits)
i2c: octeon: Support I2C_M_RECV_LEN
i2c: octeon: Cleanup resource allocation code
i2c: octeon: Cleanup i2c-octeon driver
MAINTAINERS: add Peter Rosin as i2c mux maintainer
dt-bindings: i2c: Spelling s/propoerty/property/
i2c: immediately mark ourselves as registered
i2c: i801: sort IDs alphabetically
MAINTAINERS: Mika and me are designated reviewers for I2C DESIGNWARE
i2c: octeon: Cleanup kerneldoc comments
i2c: do not use internal data from driver core
i2c: cadence: Fix the kernel-doc warnings
i2c: imx: remove extra spaces.
i2c: rcar: don't open code of_device_get_match_data()
i2c: qup: Fix fifo handling after adding V2 support
i2c: xiic: Implement power management
i2c: piix4: Pre-shift the port number
i2c: piix4: Always use the same type for port
i2c: piix4: Support alternative port selection register
i2c: tegra: don't open code of_device_get_match_data()
i2c: riic, sh_mobile, rcar: Use ARCH_RENESAS
...
|
|
Sort the list to have a faster search for a certain PCI ID.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Starting from Intel Sunrisepoint (Skylake PCH) the iTCO watchdog
resources have been moved to reside under the i801 SMBus host
controller whereas previously they were under the LPC device.
This patch adds Intel lewisburg SMBus support for iTCO device.
It allows to load watchdog dynamically when the hardware is
present.
Fixes: cdc5a3110e7c ("i2c: i801: add Intel Lewisburg device IDs")
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
Adding Intel codename Lewisburg platform device IDs for SMBus.
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Although I2C mux devices are easily enumerated using ACPI (_HID/_CID or
device property compatible string match), enumerating I2C client devices
connected through an I2C mux needs a little extra work.
This change implements a method for describing an I2C device hierarchy that
includes mux devices by using an ACPI Device() for each mux channel along
with an _ADR to set the channel number for the device. See
Documentation/acpi/i2c-muxes.txt for a simple example.
To make this work the ismt, i801, and designware pci/platform devs now
share an ACPI companion with their I2C adapter dev similar to how it's done
in OF. This is done on the assumption that power management functions will
not be called directly on the I2C dev that is sharing the ACPI node.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dustin Byford <dustin@cumulusnetworks.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This patch adds the SMBUS PCI ID of Intel Broxton.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Intel DNV SoC has the same legacy SMBus host controller than Intel
Sunrisepoint PCH. It also has same iTCO watchdog on the bus.
Add DNV PCI ID to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Starting from Intel Sunrisepoint (Skylake PCH) the iTCO watchdog resources
have been moved to reside under the i801 SMBus host controller whereas
previously they were under the LPC device.
In order to support the iTCO watchdog on newer PCHs we need to create the
platform device here in the SMBus driver and pass all known resources using
platform data.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Simplifies the code a bit and makes easier to disable PCI device on driver
detach by removing the pcim_pin_device() call in the future if needed.
Reason why i2c-i801.c doesn't ever call pci_disable_device() was because it
made some systems to hang during power-off. See commit d6fcb3b9cf77
("[PATCH] i2c-i801.c: don't pci_disable_device() after it was just enabled")
and
http://marc.info/?l=linux-kernel&m=115160053309535&w=2
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Since pci_disable_device() is not called from i801_suspend() and power
state is set already it means that subsequent pci_enable_device() calls do
practically nothing but monotonically increase struct pci_dev enable_cnt.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This simplifies the error and remove paths.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
struct pci_driver i801_driver forward declaration is needed only for
accessing the name field. Remove it and use dev_driver_string() instead.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
It makes more difficult to grep these error prints from sources if they are
split to multiple source lines.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Signed-off-by: Devin Ryles <devin.ryles@intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Don't log the host status register value in i801_isr(), it has very
little value and fills up the log when debugging is enabled.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
There is a control bit in the PCI configuration space which disables
interrupts. If this bit is set, the driver should not try to make use
of interrupts, it won't receive any.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The i2c-i801 driver can work without interrupts, so there is no reason
to make a request_irq failure fatal. Instead we can simply fallback
to polling.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Some systems have been reported to have trouble with interrupts. Use
wait_event_timeout() instead of wait_event() so we don't get stuck in
that case, and log the problem.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We have a central copy of the GPL for that. Some addresses were already
outdated.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
This patch adds the I2C/SMBus Device IDs for the Intel Sunrise Point PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The SMBus host controller is the same as used in Baytrail so add the new
PCI ID to the driver's list of supported IDs.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
A long name broke the alignment, shift the columns a bit to fix it and
make the table look nice again. While we're here, switch to the
standard comment style to make checkpatch happy, and use tabs instead
of spaces for column alignment.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add Device ID of Intel BayTrail SMBus Controller.
Signed-off-by: Chew, Kean ho <kean.ho.chew@intel.com>
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
This patch adds the SMBus Device IDs for the Intel Wildcat Point-LP PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
I2C of helpers used to live in of_i2c.c but experience (from SPI) shows
that it is much cleaner to have this in the core. This also removes a
circular dependency between the helpers and the core, and so we can
finally register child nodes in the core instead of doing this manually
in each driver. So, fix the drivers and documentation, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
