| Age | Commit message (Collapse) | Author |
|---|
|
Change all occurrences of be16 to le16 in cp2112_xfer(),
because SMBUS words are little endian, not big endian.
Signed-off-by: Ellen Wang <ellen@cumulusnetworks.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
When doing an I2C_SMBUS_BYTE write (one byte write, no address),
the data to be written is in "command" not "data->byte".
Signed-off-by: Ellen Wang <ellen@cumulusnetworks.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
cp2112_i2c_xfer() only supports a single i2c_msg. More than
one message at a time just returns EIO. This breaks certain
important cases. For example, the at24 eeprom driver generates
paired write and read messages (for eeprom address and data).
Since the device doesn't support i2c repeated starts in general,
but does support a single write-repeated-start-read pair
(since hardware rev 1), we recognize the latter case and
implement only that.
Signed-off-by: Ellen Wang <ellen@cumulusnetworks.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
cp2112_i2c_xfer() only reads up to 61 bytes, returning EIO on longers reads.
The fix is to wrap a loop around cp2112_read() to pick up all the returned
data.
Signed-off-by: Ellen Wang <ellen@cumulusnetworks.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
Current implementation of cp2112_raw_event() only accepts one data report at a
time. If last received data report is not fully handled yet, a new incoming
data report will overwrite it. In such case we don't guaranteed to propagate
the correct incoming data.
The trivial fix implemented here forces a single report at a time by requesting
in cp2112_read() no more than 61 byte of data, which is the payload size of a
single data report.
Cc: stable@vger.kernel.org
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: Ellen Wang <ellen@cumulusnetworks.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
this remove all reference to gpio_remove retval in all driver
except pinctrl and gpio. the same thing is done for gpio and
pinctrl in two different patches.
Signed-off-by: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Michael Büsch <m@bues.ch>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
cp2112 supports single I2C read/write transactions. It can't combine I2C
transactions.
Add master_xfer, using similar code flow as for smbus_xfer.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
CP2112 does not offer an atomic method to set both gpio
direction and value.
Also it does not permit to set gpio value before putting
gpio in output. In fact, accordingly to Silicon Labs
AN495, Rev. 0.2, cpt. 4.4, the HID report to set gpio
values "does not affect any pins that are not configured
as outputs".
This is confirmed on evaluation board CP2112-EK.
With current driver, after execute:
echo in > /sys/class/gpio/gpio248/direction
echo low > /sys/class/gpio/gpio248/direction
gpio output is still high. Only after a following
echo low > /sys/class/gpio/gpio248/direction
gpio output gets low.
Fix driver by changing order of operations; first set
direction then set value.
The drawback of this new sequence is that we can have
a pulse on gpio pin when direction is changed from
input to output-low, but this cannot be avoided on
current CP2112.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
tests have shown that output reports use hid_hw_output_report().
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
hid_out_raw_report is going to be obsoleted as it is not part of the
unified HID low level transport documentation
(Documentation/hid/hid-transport.txt)
hid_output_raw_report(hdev, buf, sizeof(buf), HID_FEATURE_REPORT);
is strictly equivalent to:
hid_hw_raw_request(hdev, buf[0], buf, sizeof(buf),
HID_FEATURE_REPORT, HID_REQ_SET_REPORT);
Then replace buf[0] by the appropriate define.
So use the new api.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Both cp2112_read_req() and cp2112_write_req() are returning negative
value in cases of error, but cp2112_xfer() is storing the return
value into unsigned size_t-typed 'count'.
Fix this by making 'count' signed type.
Reported-by: fengguang.wu@intel.com
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Commit cafebc0 ("HID: remove hid_get_raw_report in struct hid_device")
obsoletes the use of hdev->hid_get_raw_report(), as calling
hid_hw_raw_request() is functionally equivalent.
Convert cp2112 to use this notation.
Reported-by: fengguang.wu@intel.com
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
%zd is a proper format string specifier for size_t
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
No need to pollute namespace with dev_attr_*.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch adds support for the Silicon Labs CP2112 "Single-Chip HID USB to
SMBus Master Bridge."
This is a HID device driver which registers as an i2c adapter and gpiochip to
expose these functions of the CP2112. The customizable USB descriptor fields
are exposed as sysfs attributes. The SMBus byte-read, byte-data-read/write,
and word-data-read transfer modes have been tested by talking to an i2c
sensor. The GPIO functions and USB descriptor field programming have also
been tested.
Signed-off-by: David Barksdale <dbarksdale@uplogix.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
