| Age | Commit message (Collapse) | Author |
|---|
|
There is HPD unplug interrupts missed at scenario of an irq_hpd
followed by unplug interrupts with around 10 ms in between.
Since both AUX_SW_RESET and DP_SW_RESET clear pending HPD interrupts,
irq_hpd handler should not issues either aux or sw reset to avoid
following unplug interrupt be cleared accidentally. This patch
also postpone handling of irq_hpd until connected state if it
happened at connection pending state.
Changes in V2:
-- add postpone handling of irq_hpd until connected state
-- check DP_TRAINING_1 instead of DP_TRAINING_NONE
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The call to dpu_encoder_phys_cmd_prepare_for_kickoff is useless as
it's unused because the serialize_wait4pp variable is never set to
true by .. anything, literally: remove the call.
While at it, also reduce indentation by inverting the check for
dpu_encoder_phys_cmd_is_master.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
When configuring the tearcheck, the parameters for the engine were
being set mostly as they should've been, but then it wasn't getting
configured to get the vsync indication from the TE GPIO input
because it was assumed that autorefresh could be enabled:
since a previous commit makes sure to disable the autorefresh bit
when committing to the cmd engine, it is now safe to just enable
the vsync pin input at tearcheck setup time (instead of erroneously
never enabling it).
Also, set the right sync_cfg_height to enable the DPU auto-generated
TE signal in order to avoid stalls in the event that we miss one
external TE signal: this will still trigger recovery mechanisms in
case the display is really unreachable.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
When a command mode display is used, it may be retaining the bootloader
configuration which, in most of the cases, enables the autorefresh
feature in order to keep the splash up.
Since there is no autorefresh management in this driver, wire up the
autorefresh ops in the dpu_hw_pingpong and disable the feature when
preparing for cmd commit: instead of disabling it when initializing
the command mode, this road was chosen as to open future possibility
of enabling and managing the autorefresh feature in the driver.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The DSPP_BLK macro was ad-hoc made for SC7180, but this is wrong
because not all of the DPU DSPP versions can use the same DSPP block
configuration, and not all of them have got the same features.
For this reason, add two more params to the DSPP_BLK macro, so that
it is possible to specify the feature mask and the sblk config for
each DSPP.
Fixes: 4259ff7ae509 ("drm/msm/dpu: add support for pcc color block in dpu driver")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Not all DPU interface sub-block versions need the same value for
prog_fetch_lines_worst_case: add this to the INTF_BLK macro, so
that it becomes possible to vary it for other INTF versions.
For example, this is needed to implement support for older SoCs,
like MSM8998 and SDM630/660 and most probably will also be needed
for future SoCs.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Not all DPU versions that are supported in this driver are supposed
to have a 8-Levels VIG QoS setting.
Move this flag to SDM845 and SC7180 specific masks.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
On DPUs prior to version 4 the VBIF_XINL_QOS_LVL_REMAP_000 register
is at 0x570 offset from vbif base instead of 0x590, due to the
VBIF_XINL_QOS_RP_REMAP_000 having less instances (less possible XINs).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Port over the command from downstream to prevent undefined
behaviour.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Port over the command from downstream to prevent undefined
behaviour.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The upstream API for some reason uses logbase2 instead of
just passing the argument as-is, whereas downstream CAF
kernel does the latter.
Hence, a mistake has been made when porting:
4 is the value that's supposed to be passed, but
log2(4) = 2. Changing the value to 16 (= 2^4) fixes
the issue.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Resetting the VBIF before power collapse is done to avoid getting
bogus FIFO entries during the suspend sequence or subsequent resume,
but this is doable only on Adreno 510 and Adreno 530, as the other
units will tendentially lock up.
Especially on Adreno 508, the GPU will show lockups and very bad
slownesses after processing the first frame.
Avoiding to execute the RBBM SW Reset before suspend will stop the
lockup issue from happening on at least Adreno 508/509/512.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The Adreno 508/509/512 GPUs are stripped versions of the Adreno
5xx found in the mid-end SoCs such as SDM630, SDM636, SDM660 and
SDA variants; these SoCs are usually provided with ZAP firmwares,
but they have no available GPMU.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Tested-by: Martin Botka <martin.botka1@gmail.com>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The "main" if branch where we program the other registers for the
Adreno 5xx family of GPUs should not contain the PC_DBG_ECO_CNTL
register programming because this has logical similarity
differences from all the others.
A later commit will show the entire sense of this.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The PC_DBG_ECO_CNTL register on the Adreno A5xx family gets
programmed to some different values on a per-model basis.
At least, this is what we intend to do here;
Unfortunately, though, this register is being overwritten with a
static magic number, right after applying the GPU-specific
configuration (including the GPU-specific quirks) and that is
effectively nullifying the efforts.
Let's remove the redundant and wrong write to the PC_DBG_ECO_CNTL
register in order to retain the wanted configuration for the
target GPU.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
A6XX GPUs have support for last level cache(LLC) also known
as system cache and need to set the bus attributes to
use it. Currently we use a generic adreno iommu address space
implementation which are also used by older GPU generations
which do not have LLC and might introduce issues accidentally
and is not clean in a way that anymore additions of GPUs
supporting LLC would have to be guarded under ifdefs. So keep
the generic code separate and make the address space creation
A6XX specific. We also have a helper to set the llc attributes
so that if the newer GPU generations do support them, we can
use it instead of open coding domain attribute setting for each
GPU.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Domain attribute setting for LLCC is guarded by !IS_ERR
check which works fine only when CONFIG_QCOM_LLCC=y but
when it is disabled, the LLCC apis return NULL and that
is not handled by IS_ERR check. Due to this, domain attribute
for LLCC will be set even on GPUs which do not support it
and cause issues, so correct this by using IS_ERR_OR_NULL
checks appropriately. Meanwhile also cleanup comment block
and remove unwanted blank line.
Fixes: 00fd44a1a470 ("drm/msm: Only enable A6xx LLCC code on A6xx")
Fixes: 474dadb8b0d5 ("drm/msm/a6xx: Add support for using system cache(LLC)")
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
On at least MSM8998 it's possible to find Adreno 540.0 and 540.1
but I have never found any 540.2. In any case, the patchids 0-1
for A540 are completely supported by this driver and there is no
reason to disallow probing them (as they also share the same
firmware names).
Besides that, the patchid number is also used in the a5xx_power.c
function a540_lm_setup to disable the battery current limiter,
which makes faking the Adreno patchid to .2 (which would anyway
be sad) useless and even producing breakages.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The msm_gem_get_iova should be guarded with gpu != NULL and not aspace
!= NULL, because aspace is NULL when using vram carveout.
Fixes: 933415e24bd0d ("drm/msm: Add support for private address space instances")
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Tested-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Some GPUs support different max frequencies depending on the platform.
To identify the correct variant, we should check the gpu speedbin
fuse value. Add support for this speedbin detection to a6xx family
along with the required fuse details for a618 gpu.
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-5.11-2021-01-21:
amdgpu:
- Green Sardine fixes
- Vangogh fixes
- Renoir fixes
- Misc display fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210121160129.3981-1-alexander.deucher@amd.com
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v5.11-rc5:
- HDCP fixes
- PMU wakeref fix
- Fix HWSP validity race
- Fix DP protocol converter accidental 4:4:4->4:2:0 conversion for RGB
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87a6t2kzgb.fsf@intel.com
|
|
Starting from vangogh, the ATCL2 and DAGB0 registers relative
to mgcg/ls has changed.
For MGCG:
Replace mmMM_ATC_L2_MISC_CG with mmMM_ATC_L2_CGTT_CLK_CTRL.
For MGLS:
Replace mmMM_ATC_L2_MISC_CG with mmMM_ATC_L2_CGTT_CLK_CTRL.
Add DAGB0_(WR/RD)_CGTT_CLK_CTRL registers.
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
GCR_GENERAL_CNTL is defined differently in gc_10_1_0_offset.h and
gc_10_3_0_offset.h. Update GCR_GENERAL_CNTL for Vangogh.
Signed-off-by: Jinzhou Su <Jinzhou.Su@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
mmnbif_gpu_BIF_DOORBELL_FENCE_CNTL added in FSDL
In the renoir there is no need GpuChangeState message set to exit gfxoff in the s0i3 resume since
mmnbif_gpu_BIF_DOORBELL_FENCE_CNTL has been added in the s0i3 FSDL.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[why]
Heavy corruption or blank screen reported on wake,
with 6k display connected and FEC enabled
[how]
When Disable/Enable stream for display pipes on HPDRX,
DC should take into account ODM split pipes.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
These can differ per ASIC or not be present. Don't call the dcn20 ones
directly but rather the ones defined by the ASIC init table.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
looping
Why:
Function decide_dp_link_settings() loops infinitely when required bandwidth
can't be supported.
How:
Check the required bandwidth against verified_link_cap before trying to
find a link setting for it.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Bing Guo <bing.guo@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When no displays are currently enabled, display driver should not
disallow PSTATE switching.
[How]
Allow PSTATE switching if either the active configuration supports it,
or there are no active displays.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
dram clock change latencies get updated using ddr4 latency table, but
that update does not happen before validation. This value
should not be the default and should be number received from
df for better mode support.
This may cause a PState hang on high refresh panels with short vblanks
such as on 1080p 360hz or 300hz panels.
[HOW]
Update latency from 23.84 to 11.72.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The ip discovery is supported on green sardine, it doesn't need gpu info
firmware anymore.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.10.x
|
|
[WHY]
Previously as MPO + ODM Combine was not supported, finding secondary pipes
for each case was mutually exclusive. Now that both are supported at the same
time, both cases should be taken into account when finding a secondary pipe.
[HOW]
If a secondary pipe cannot be found based on previous bottom pipe,
search for a second pipe using next_odm_pipe instead.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.10.x
|
|
While reviewing Christian's annotation patch I noticed that we have a
user-after-free for the WAIT_FOR_SUBMIT case: We drop the syncobj
reference before we've completed the waiting.
Of course usually there's nothing bad happening here since userspace
keeps the reference, but we can't rely on userspace to play nice here!
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Fixes: bc9c80fe01a2 ("drm/syncobj: use the timeline point in drm_syncobj_find_fence v4")
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.2+
Link: https://patchwork.freedesktop.org/patch/msgid/20210119130318.615145-1-daniel.vetter@ffwll.ch
|
|
For performance, BO page mappings can stay in place even if the
map counter has returned to 0. In these cases, the existing page
mapping has to be reused by the next vmap operation. Otherwise
a new mapping would be installed and the old mapping's pages leak.
Fix the issue by reusing existing page mappings for vmap operations.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 1086db71a1db ("drm/vram-helper: Remove invariant parameters from internal kmap function")
Acked-by: Christian König <christian.koenig@amd.com>
Tested-by: Eli Cohen <elic@nvidia.com>
Reported-by: Eli Cohen <elic@nvidia.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Christian König <christian.koenig@amd.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20210118144639.27307-1-tzimmermann@suse.de
|
|
Put the state before returning error code.
Fixes: 44596b8c4750 ("drm/atomic: Unify conflicting encoder handling.")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210119121127.84127-1-bianpan2016@163.com
|
|
Let's not enable the 4:4:4->4:2:0 conversion bit in the DFP unless we're
actually outputting YCbCr 4:4:4. It would appear some protocol
converters blindy consult this bit even when the source is outputting
RGB, resulting in a visual mess.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2914
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111164111.13302-1-ville.syrjala@linux.intel.com
Fixes: 181567aa9f0d ("drm/i915: Do YCbCr 444->420 conversion via DP protocol converters")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 3170a21f7059c4660c469f59bf529f372a57da5f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210118154355.24453-1-ville.syrjala@linux.intel.com
|
|
Since we allow removing the timeline map at runtime, there is a risk
that rq->hwsp points into a stale page. To control that risk, we hold
the RCU read lock while reading *rq->hwsp, but we missed a couple of
important barriers. First, the unpinning / removal of the timeline map
must be after all RCU readers into that map are complete, i.e. after an
rcu barrier (in this case courtesy of call_rcu()). Secondly, we must
make sure that the rq->hwsp we are about to dereference under the RCU
lock is valid. In this case, we make the rq->hwsp pointer safe during
i915_request_retire() and so we know that rq->hwsp may become invalid
only after the request has been signaled. Therefore is the request is
not yet signaled when we acquire rq->hwsp under the RCU, we know that
rq->hwsp will remain valid for the duration of the RCU read lock.
This is a very small window that may lead to either considering the
request not completed (causing a delay until the request is checked
again, any wait for the request is not affected) or dereferencing an
invalid pointer.
Fixes: 3adac4689f58 ("drm/i915: Introduce concept of per-timeline (context) HWSP")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: <stable@vger.kernel.org> # v5.1+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218122421.18344-1-chris@chris-wilson.co.uk
(cherry picked from commit 9bb36cf66091ddf2d8840e5aa705ad3c93a6279b)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210118101755.476744-1-chris@chris-wilson.co.uk
|
|
Chris found a CI report which points out calling intel_runtime_pm_get from
inside i915_pmu_enable hook is not allowed since it can be invoked from
hard irq context. This is something we knew but forgot, so lets fix it
once again.
We do this by syncing the internal book keeping with hardware rc6 counter
on driver load.
v2:
* Always sync on parking and fully sync on init.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: f4e9894b6952 ("drm/i915/pmu: Correct the rc6 offset upon enabling")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201214094349.3563876-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit dbe13ae1d6abaab417edf3c37601c6a56594a4cd)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210118100724.465555-1-chris@chris-wilson.co.uk
|
|
On error we unpin and free the wa_ctx.vma, but do not clear any of the
derived flags. During lrc_init, we look at the flags and attempt to
dereference the wa_ctx.vma if they are set. To protect the error path
where we try to limp along without the wa_ctx, make sure we clear those
flags!
Reported-by: Matt Roper <matthew.d.roper@intel.com>
Fixes: 604a8f6f1e33 ("drm/i915/lrc: Only enable per-context and per-bb buffers if set")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.15+
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108204026.20682-1-chris@chris-wilson.co.uk
(cherry-picked from 5b4dc95cf7f573e927fbbd406ebe54225d41b9b2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210118095332.458813-1-chris@chris-wilson.co.uk
|
|
User-space ALSA matches a card's driver name against an internal list of
aliases in order to select the correct configuration for the system.
When the driver name isn't defined, the match is performed against the
card's name.
With the introduction of RPi4 we now have two HDMI ports with two
distinct audio cards. This is reflected in their names, making them
different from previous RPi versions. With this, ALSA ultimately misses
the board's configuration on RPi4.
In order to avoid this, set "card->driver_name" to "vc4-hdmi"
unanimously.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Fixes: f437bc1ec731 ("drm/vc4: drv: Support BCM2711")
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210115191209.12852-1-nsaenzjulienne@suse.de
|
|
The only flag we really need is __GFP_NOMEMALLOC, highmem depends on
dma32 and moveable/compound should never be set in the first place.
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/413812/
Link: https://patchwork.freedesktop.org/patch/413964/
Fixes: d099fc8f540a ("drm/ttm: new TT backend allocation pool v3")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Get DRM connector reference count while scheduling a prop work
to avoid any possible destroy of DRM connector when it is in
DRM_CONNECTOR_REGISTERED state.
Fixes: a6597faa2d59 ("drm/i915: Protect workers against disappearing connectors")
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-3-anshuman.gupta@intel.com
(cherry picked from commit b3c6661aad979ec3d4f5675cf3e6a35828607d6a)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
When crtc state need_modeset is true it is not necessary
it is going to be a real modeset, it can turns to be a
fastset instead of modeset.
This turns content protection property to be DESIRED and hdcp
update_pipe left with property to be in DESIRED state but
actual hdcp->value was ENABLED.
This issue is caught with DP MST setup, where we have multiple
connector in same DP_MST topology. When disabling HDCP on one of
DP MST connector leads to set the crtc state need_modeset to true
for all other crtc driving the other DP-MST topology connectors.
This turns up other DP MST connectors CP property to be DESIRED
despite the actual hdcp->value is ENABLED.
Above scenario fails the DP MST HDCP IGT test, disabling HDCP on
one MST stream should not cause to disable HDCP on another MST
stream on same DP MST topology.
v2:
- Fixed connector->base.registration_state == DRM_CONNECTOR_REGISTERED
WARN_ON.
v3:
- Commit log improvement. [Uma]
- Added a comment before scheduling prop_work. [Uma]
Fixes: 33f9a623bfc6 ("drm/i915/hdcp: Update CP as per the kernel internal state")
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-2-anshuman.gupta@intel.com
(cherry picked from commit d276e16702e2d634094f75f69df3b493f359fe31)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
topic/nouveau-ampere-modeset
This adds support for basic modeseting on the nvidia ampere chipsets. This code should all
be contained to just those and have no effect on current hardware.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Ben Skeggs <skeggsb@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CACAvsv5LmMP+HbDUQBf_dy1-0eS9fA32k8HWo4y5X4-7rsw-yw@mail.gmail.com
|
|
into drm-fixes
As requested, here's a tree with the non-Ampere-specific fixes split
out, as most of them are potentially relevant to already-supported
GPUs.
- irq handling fix
- expansion ROM fix
- hw init dpcd disable
- aux semaphore owner field fix
- vram heap sizing fix
- notifier at 0 is valid fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Ben Skeggs <skeggsb@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CACAvsv4P90mcF_ByAh+ghz+ZVD2N2bPbD7xHYYArE1kYrvsGcQ@mail.gmail.com
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-5.11-2021-01-14:
amdgpu:
- Update repo location in MAINTAINERS
- Add some new renoir PCI IDs
- Revert CRC UAPI changes
- Revert OLED display fix which cases clocking problems for some systems
- Misc vangogh fixes
- GFX fix for sienna cichlid
- DCN1.0 fix for pipe split
- Fix incorrect PSP command
amdkfd:
- Fix possible out of bounds read in vcrat creation
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210114201354.3998-1-alexander.deucher@amd.com
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v5.11-rc4:
- Allow the sysadmin to override security mitigations
- Restore clear-residual mitigations for ivb/byt
- Limit VFE threads based on GT
- GVT: fix vfio edid and full display detection
- Fix DSI DSC power refcounting
- Fix LPT CPU mode backlight takeover
- Disable RPM wakeref assertions during driver shutdown
- Fix DSI sequence sleeps
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87sg73pz42.fsf@intel.com
|
|
UEFI/RM no longer use IED scripts from the VBIOS, though they appear to
have been updated for use by the x86 VBIOS code, so we should be able to
continue using them for the moment.
Unfortunately, we require some hacks to do so, as the BeforeLinkTraining
IED script became a pointer to an array of scripts instead, without a
revbump of the relevant tables.
There's also some changes to SOR clock divider fiddling, which are
hopefully correct enough that things work as they should.
AFAIK, GA100 shouldn't have display, so it hasn't been added.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Appears to be compatible with GV100 code, and not required on GA100, as
it shouldn't have display.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Appears to be compatible with GM200 code.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
