| Age | Commit message (Collapse) | Author |
|---|
|
The MIPI DSI output on Tegra SoCs requires some external logic to
calibrate the MIPI pads before a video signal can be transmitted. This
MIPI calibration logic requires to be powered on while the MIPI pads are
being used, which is currently done as part of the DSI driver's probe
implementation.
This is suboptimal because it will leave the MIPI calibration logic
powered up even if the DSI output is never used.
On Tegra114 and earlier this behaviour also causes the driver to hang
while trying to power up the MIPI calibration logic because the power
partition that contains the MIPI calibration logic will be powered on
by the display controller at output pipeline configuration time. Thus
the power up sequence for the MIPI calibration logic happens before
it's power partition is guaranteed to be enabled.
Fix this by splitting up the API into a request/free pair of functions
that manage the runtime dependency between the DSI and the calibration
modules (no registers are accessed) and a set of enable, calibrate and
disable functions that program the MIPI calibration logic at points in
time where the power partition is really enabled.
While at it, make sure that the runtime power management also works in
ganged mode, which is currently also broken.
Reported-by: Jonathan Hunter <jonathanh@nvidia.com>
Tested-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Keep track of the number of users of DSI and CSI pads and power down the
regulators that supply the bricks when all users are gone.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Some changes are needed to the configuration settings for some lanes. In
addition, the clock lanes for the CSI pads can no longer be calibrated.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
While Tegra132 has the same pads as Tegra124, some configuration values
need to be programmed slightly differently.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This table is never modified and can therefore reside in read-only
memory.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Before starting a new calibration cycle, make sure to clear the current
status by writing a 1 to the various "calibration done" bits.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Use more consistent names for the clock lane configuration registers and
fix the offset of the upper clock lane configuration register for the
first DSI pad.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Parameterize more of the register programming to accomodate for changes
required by future SoC generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
During calibration, sets the "internal reference level for drive pull-
down" to the value specified in the Tegra TRM.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Include the clock lanes when calibrating the MIPI PHY on Tegra124
compatible devices.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
[treding@nvidia.com: bikeshedding]
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
By paving the CTRL reg value, the current code changes MIPI_CAL_PRESCALE
("Auto-cal calibration step prescale") from 1us to 0.1us (val=0). In the
description for PHY's noise filter (MIPI_CAL_NOISE_FLT), the TRM states
that if the value of the prescale is 0 (or 0.1us), the filter should be
set between 2-5. However, the current code sets it to 0.
For now, let's keep the prescale and filter values as-is, which is most
likely the power-on-reset values of 0x2 and 0xa, respectively.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
On 64-bit platforms an unsigned long would be 64 bit and cause
unnecessary casting when being passed to writel() or returned from
readl(). Make register values 32 bits wide to avoid that.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Include the linux/host1x.h and dev.h headers so that function prototypes
are visible to keep sparse from suggesting that their implementations be
made static.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This driver adds support to perform calibration of the MIPI pads for CSI
and DSI.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
