| Age | Commit message (Collapse) | Author |
|---|
|
If the SOR is already up and running when the kernel driver is probed,
setting a mode will typically fail. This can be seen for example on
Jetson TX2. Under certain circumstances the generic power domain code
will cause the SOR to be reset. However, if the power domain is never
powered off (this can happen if the HDA controller is enabled, which
is part of the same power domain as the SOR), then the SOR will end up
not getting reset and fail to properly set a mode.
To work around this, try to get the reset control and assert/deassert
it, irrespective of whether or not a generic power domain is attached
to the SOR. On platforms where the kernel implements generic power
domains (up to Tegra210) this will fail, because the power domain will
already have acquired an exclusive reference to the reset control. But
on recent platforms there the BPMP provides an ABI to control power
domains, it's possible to acquire the reset control from SOR and use
it to put the SOR into a known good state at probe time.
The proper solution for this is to make the SOR driver capable of
dealing with hardware that's already up and running (by first grace-
fully shutting it down, or perhaps by seamlessly transitioning to the
kernel driver and taking over the running display configuration). That
is fairly involved, though, so we'll go with this quickfix for now.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Remove the temporary workaround of storing the Tegra186 HDMI/DP I/O pad
ID in the SOR driver. The definition has long been available in the
soc/tegra/pmc.h header file.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This code is very similar to the audio over HDMI support on older chips.
Interoperation with the audio codec is done via a pair of codec scratch
registers and an interrupt that is raised at the SOR when the codec has
written those registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Display controllers that don't own any windows and which therefore
aren't currently being assigned a primary plane are not registered
as a CRTC with the DRM framework. They request neither a syncpoint
nor an interrupt because they don't use them, so avoid cleaning up
those resources.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The display architecture on Tegra186 and Tegra194 requires that there be
some valid clock on all domains before accessing any display register. A
further requirement is that in addition to the host1x, hub, disp and dsc
clocks, all the head clocks (pclk0-2 on Tegra186 or pclk0-3 on Tegra194)
must also be enabled.
Implement this logic within the display hub driver to ensure the clocks
are always enabled at the right time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Video Image Composer (VIC) generation found on Tegra194 is backwards
compatible with its predecessor found on Tegra186.
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Before booting the Falcon processor, make sure to wait for memory
scrubbing to complete.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The ->alloc() callback in struct falcon_ops returns an ERR_PTR()-encoded
error code on failure, so it needs to be properly checked for, otherwise
subsequent code may dereference an invalid pointer.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra supports generic PM domains on 64-bit ARM, and if that is enabled,
the power domain code will make sure that resets are asserted and
deasserted at appropriate points in time.
If generic PM domains are not implemented, such as on 32-bit Tegra, the
resets need to be asserted and deasserted explicitly by the driver.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.20-rc1
This contains initial Tegra194 support as well as a couple of fixes for
DMA/IOMMU integration.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205051.30017-1-thierry.reding@gmail.com
|
|
All Tegra DRM devices are getting attached to an implicit IOMMU DMA
domain if CONFIG_ARM_DMA_USE_IOMMU=y. Since Tegra DRM driver manages IOMMU
by itself, the devices must be detached from the implicit domain using
arch-specific IOMMU-API. Note that this works only for arm32 and not for
arm64, which will remain broken if CONFIG_IOMMU_DMA is enabled.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This patch unifies the naming of DRM functions for reference counting
of struct drm_device. The resulting code is more aligned with the rest
of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180926115640.24755-1-tzimmermann@suse.de
|
|
The SOR implemented in Tegra194 is subtly different from its predecessor
found in Tegra186. Most notably some registers have been moved around so
it is no longer compatible.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The DPAUX controller found on Tegra194 is almost identical to its
predecessor from Tegra186.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The display controllers found on Tegra194 are almost identical to those
found on Tegra186.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The display hub integrated into Tegra194 is almost identical to the one
found on Tegra186. However, it doesn't support DSC (display stream
compression) so it isn't fully compatible.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra194 contains a fourth display controller that does not own any
windows. Therefore, we cannot currently assign a primary plane to it
which causes KMS to eventually crash. Do not register the display
controller if it owns no windows to work around this.
Note that we still have to enable and probe the display controller
because for some reason all display controllers need to be powered
(and/or clocked) before any registers can be accessed in any of the
display controllers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Some of definitions in the code changed the meaning, unfortunately one
place missed the change.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
convert drm_atomic_helper_suspend/resume() to use
drm_mode_config_helper_suspend/resume().
With this conversion, tegra_drm_fb_suspend() and
tegra_drm_fb_resume() will not be used anymore.
Both of these functions can be removed.
Also, in tegra_drm struct's member state will not be
used anymore. So this can be removed forever.
Fixed one sparse warning.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Ajit Negi <ajitn.linux@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Kick out firmware fb when loading Tegra driver.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/b5c3972e5774d0d1f8887054a993bbc54e9dbe2a.1535810304.git.mirq-linux@rere.qmqm.pl
|
|
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.19.
Rob has some new hardware support for new qualcomm hw that I'll send
along separately. This has the display part of it, the remaining pull
is for the acceleration engine.
This also contains a wound-wait/wait-die mutex rework, Peter has acked
it for merging via my tree.
Otherwise mostly the usual level of activity. Summary:
core:
- Wound-wait/wait-die mutex rework
- Add writeback connector type
- Add "content type" property for HDMI
- Move GEM bo to drm_framebuffer
- Initial gpu scheduler documentation
- GPU scheduler fixes for dying processes
- Console deferred fbcon takeover support
- Displayport support for CEC tunneling over AUX
panel:
- otm8009a panel driver fixes
- Innolux TV123WAM and G070Y2-L01 panel driver
- Ilitek ILI9881c panel driver
- Rocktech RK070ER9427 LCD
- EDT ETM0700G0EDH6 and EDT ETM0700G0BDH6
- DLC DLC0700YZG-1
- BOE HV070WSA-100
- newhaven, nhd-4.3-480272ef-atxl LCD
- DataImage SCF0700C48GGU18
- Sharp LQ035Q7DB03
- p079zca: Refactor to support multiple panels
tinydrm:
- ILI9341 display panel
New driver:
- vkms - virtual kms driver to testing.
i915:
- Icelake:
Display enablement
DSI support
IRQ support
Powerwell support
- GPU reset fixes and improvements
- Full ppgtt support refactoring
- PSR fixes and improvements
- Execlist improvments
- GuC related fixes
amdgpu:
- Initial amdgpu documentation
- JPEG engine support on VCN
- CIK uses powerplay by default
- Move to using core PCIE functionality for gens/lanes
- DC/Powerplay interface rework
- Stutter mode support for RV
- Vega12 Powerplay updates
- GFXOFF fixes
- GPUVM fault debugging
- Vega12 GFXOFF
- DC improvements
- DC i2c/aux changes
- UVD 7.2 fixes
- Powerplay fixes for Polaris12, CZ/ST
- command submission bo_list fixes
amdkfd:
- Raven support
- Power management fixes
udl:
- Cleanups and fixes
nouveau:
- misc fixes and cleanups.
msm:
- DPU1 support display controller in sdm845
- GPU coredump support.
vmwgfx:
- Atomic modesetting validation fixes
- Support for multisample surfaces
armada:
- Atomic modesetting support completed.
exynos:
- IPPv2 fixes
- Move g2d to component framework
- Suspend/resume support cleanups
- Driver cleanups
imx:
- CSI configuration improvements
- Driver cleanups
- Use atomic suspend/resume helpers
- ipu-v3 V4L2 XRGB32/XBGR32 support
pl111:
- Add Nomadik LCDC variant
v3d:
- GPU scheduler jobs management
sun4i:
- R40 display engine support
- TCON TOP driver
mediatek:
- MT2712 SoC support
rockchip:
- vop fixes
omapdrm:
- Workaround for DRA7 errata i932
- Fix mm_list locking
mali-dp:
- Writeback implementation
PM improvements
- Internal error reporting debugfs
tilcdc:
- Single fix for deferred probing
hdlcd:
- Teardown fixes
tda998x:
- Converted to a bridge driver.
etnaviv:
- Misc fixes"
* tag 'drm-next-2018-08-15' of git://anongit.freedesktop.org/drm/drm: (1506 commits)
drm/amdgpu/sriov: give 8s for recover vram under RUNTIME
drm/scheduler: fix param documentation
drm/i2c: tda998x: correct PLL divider calculation
drm/i2c: tda998x: get rid of private fill_modes function
drm/i2c: tda998x: move mode_valid() to bridge
drm/i2c: tda998x: register bridge outside of component helper
drm/i2c: tda998x: cleanup from previous changes
drm/i2c: tda998x: allocate tda998x_priv inside tda998x_create()
drm/i2c: tda998x: convert to bridge driver
drm/scheduler: fix timeout worker setup for out of order job completions
drm/amd/display: display connected to dp-1 does not light up
drm/amd/display: update clk for various HDMI color depths
drm/amd/display: program display clock on cache match
drm/amd/display: Add NULL check for enabling dp ss
drm/amd/display: add vbios table check for enabling dp ss
drm/amd/display: Don't share clk source between DP and HDMI
drm/amd/display: Fix DP HBR2 Eye Diagram Pattern on Carrizo
drm/amd/display: Use calculated disp_clk_khz value for dce110
drm/amd/display: Implement custom degamma lut on dcn
drm/amd/display: Destroy aux_engines only once
...
|
|
Merge changes in the PM core, system-wide PM infrastructure, generic
power domains (genpd) framework, ACPI PM infrastructure and cpuidle
for 4.19.
* pm-core:
driver core: Add flag to autoremove device link on supplier unbind
driver core: Rename flag AUTOREMOVE to AUTOREMOVE_CONSUMER
* pm-domains:
PM / Domains: Introduce dev_pm_domain_attach_by_name()
PM / Domains: Introduce option to attach a device by name to genpd
PM / Domains: dt: Add a power-domain-names property
* pm-sleep:
PM / reboot: Eliminate race between reboot and suspend
PM / hibernate: Mark expected switch fall-through
x86/power/hibernate_64: Remove VLA usage
PM / hibernate: cast PAGE_SIZE to int when comparing with error code
* acpi-pm:
ACPI / PM: save NVS memory for ASUS 1025C laptop
ACPI / PM: Default to s2idle in all machines supporting LP S0
* pm-cpuidle:
ARM: cpuidle: silence error on driver registration failure
|
|
rmk requested this for armada and I think we've had a few
conflicts build up.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Again to align with the usual prefix of just drm_connector_. Again
done with sed + manual fixup for indent issues.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709084016.23750-7-daniel.vetter@ffwll.ch
|
|
Just makes it longer, and for most things in drm_connector.[hc] we
just use the drm_connector_ prefix. Done with sed + a bit of manual
fixup for the indenting.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709084016.23750-6-daniel.vetter@ffwll.ch
|
|
Right now, the DRM panel logic returns NULL when a panel pointing to
the passed OF node is not present in the list of registered panels.
Most drivers interpret this NULL value as -EPROBE_DEFER, but we are
about to modify the semantic of of_drm_find_panel() and let the
framework return -ENODEV when the device node we're pointing to has
a status property that is not equal to "okay" or "ok".
Let's first patch the of_drm_find_panel() implementation to return
ERR_PTR(-EPROBE_DEFER) instead of NULL and patch all callers to replace
the '!panel' check by an 'IS_ERR(panel)' one.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180509130042.9435-2-boris.brezillon@bootlin.com
|
|
Now that we want to add another flag to autoremove the device link
on supplier unbind, it's fair to rename the existing flag from
DL_FLAG_AUTOREMOVE to DL_FLAG_AUTOREMOVE_CONSUMER so that we can
add similar flag for supplier later.
And, while we are touching device.h, fix a doc build warning.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Here we are checking for the buffer length, not an offset for writing
to, so using > is correct. The current code incorrectly rejects a
command buffer ending at the memory buffer's end.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
We got a few conflicts in drm_atomic.c after merging the DRM writeback support,
now we need a backmerge to unlock develop development on drm-misc-next.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
|
|
Neither used nor correctly implemented anywhere. Just completely remove
the interface.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://patchwork.freedesktop.org/patch/226645/
|
|
git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.18-rc1
This set enables IOMMU support in the gr2d and gr3d drivers and adds
support for the zpos property on older Tegra generations. It also
enables scaling filters and incorporates some rework to eliminate a
private wrapper around struct drm_framebuffer.
The remainder is mostly a random assortment of fixes and cleanups, as
well as some preparatory work for destaging the userspace ABI, which
is almost ready and is targetted for v4.19-rc1.
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Sat 19 May 2018 08:31:00 AEST
# gpg: using RSA key DD23ACD77F3EB3A1
# gpg: Can't check signature: public key not found
Link: https://patchwork.freedesktop.org/patch/msgid/20180518224523.30982-1-thierry.reding@gmail.com
|
|
Set the interface version implemented by the VIC module. This allows
userspace to pass the correct command stream when programming the VIC
module.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Set the interface version implemented by the gr3d module. This allows
userspace to pass the correct command stream when programming the gr3d
module.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Set the interface version implemented by the gr2d module. This allows
userspace to pass the correct command stream when programming the gr2d
module.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Userspace needs to know the version of the interface implemented by a
client so it can create the proper command streams. Allow individual
drivers to store this version along with the client so that it can be
returned to userspace upon opening a channel.
Acked-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Currently only the DRM_MODE_REFLECT_Y rotation is supported. The driver
already supports reflection on the Y axis via a custom flag which is not
very useful because it requires custom userspace. Add the standard
rotation property that supports 0 degree rotation and Y axis reflection
for primary and overlay planes to provide a better interface than the
custom flag.
v2: keep custom flag for ABI compatibility (Dmitry)
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Set the owner and name of the exported DMA-BUF in addition to the
already filled-in fields.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
All other array variables use a plural, and this is the only one using
the *array suffix. This is confusing, so rename it for consistency.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Rather than storing some identifier derived from the application
context that can't be used concretely anywhere, store a pointer to the
client directly so that accesses can be made directly through that
client object.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The job submission userspace ABI doesn't support this and there are no
plans to implement it, so all of this code is dead and can be removed.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Now that our destroy function is the same as the helper, use that
directly.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
User framebuffers are created with either bo->pages or bo->vaddr set,
depending on whether or not an IOMMU is present. On the other hand, the
framebuffer created for fbdev emulation has a vaddr mapping made if
bo->pages is set after creation. This is set up in fbdev probe.
Remove the special case unmapping from the general-purpose framebuffer
destroy, and move it to fbdev teardown.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Since tegra_fb is now the same as drm_framebuffer, we can just replace
the type completely.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Since drm_framebuffer can now store GEM objects directly, place them
there rather than in our own subclass. As this makes the framebuffer
create_handle function the same as the GEM framebuffer helper, we
can reuse that.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
drm_framebuffer already stores num_planes for us.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Use new return type vm_fault_t for fault handler. For now, this is just
documenting that the function returns a VM_FAULT value rather than an
errno. Once all instances are converted, vm_fault_t will become a
distinct type.
Reference id -> 1c8f422059ae ("mm: change return type to vm_fault_t")
Previously vm_insert_page() returns err which driver mapped into
VM_FAULT_* type. The new function vmf_insert_page() will replace this
inefficiency by returning VM_FAULT_* type.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The IOVA API uses a memory cache to allocate IOVA nodes from. To make
sure that this cache is available, obtain a reference to it and release
the reference when the cache is no longer needed.
On 64-bit ARM this is hidden by the fact that the DMA mapping API gets
that reference and never releases it. On 32-bit ARM, however, the DMA
mapping API doesn't do that, so allocation of IOVA nodes fails.
Fixes: ad92601521ea ("drm/tegra: Add Tegra DRM allocation API")
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The original code works fine, this is merely a cosmetic change to make
the teardown order the reverse of the setup order.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Older Tegra chips do support blending as well. Rename the SoC info entry
.supports_blending to .has_legacy_blending to eliminate the confusion.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Older Tegra's do not support plane's Z position handling in hardware,
but the hardware provides knobs to implement it in software.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
