| Age | Commit message (Collapse) | Author |
|---|
|
Neither of these code-paths apply to older 32b devices, but it is rude
to introduce warnings.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929001925.2916984-1-robdclark@gmail.com
|
|
https://gitlab.freedesktop.org/drm/msm into drm-next
* DSI support for sm8150/sm8250
* Support for per-process GPU pagetables (finally!) for a6xx.
There are still some iommu/arm-smmu changes required to
enable, without which it will fallback to the current single
pgtable state. The first part (ie. what doesn't depend on
drm side patches) is queued up for v5.10[1].
* DisplayPort support. Userspace DP compliance tool support
is already merged in IGT[2]
* The usual assortment of smaller fixes/cleanups
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvqjuzH=Po_9EzzFsp2Xq3tqJUTKfsA2g09XY7_+6Ypfw@mail.gmail.com
|
|
This adds support for the 7nm ("V4") DSI PHY/PLL for sm8150 and sm8250.
Implementation is based on 10nm driver, but updated based on the downstream
7nm driver.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> (SM8250)
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
This allows DSI driver to work with sm8150 and sm8250. The sdm845 config
is re-used as the config is the same.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> (SM8250)
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The clk_pre/clk_post values in shared_timings are used instead, and these
are unused.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> (SM8250)
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Backmerging drm-next into drm-misc-next for nouveau and panel updates.
Resolves a conflict between ttm and nouveau, where struct ttm_mem_res got
renamed to struct ttm_resource.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
|
|
These functions are now empty and no longer
useful so remove the functions and their uses.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Bernard Zhao <bernard@vivo.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>,
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Icenowy Zheng <icenowy@aosc.io>,
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Robert Chiras <robert.chiras@nxp.com>
Cc: dri-devel@lists.freedesktop.org,
Cc: linux-kernel@vger.kernel.org
Cc: opensource.kernel@vivo.com
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> # Fixed build and a few warnings
Link: https://patchwork.freedesktop.org/patch/msgid/9e13761020750b1ce2f1fabee23ef6e2a2942882.camel@perches.com
|
|
This also applies to sdm630/636 and their SDA
counterparts.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
These SoCs make use of the 14nm phy, but at different
addresses than other 14nm units.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
We haven't sync'd for a while.. pull in updates to get definitions for
some fields in pkt7 payloads.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
On SDM845 and SC7180 DSI needs to express a performance state
requirement on a power domain depending on the clock rates.
Use OPP table from DT to register with OPP framework and use
dev_pm_opp_set_rate() to set the clk/perf state.
dev_pm_opp_set_rate() is designed to be equivalent to clk_set_rate()
for devices without an OPP table, hence the change works fine
on devices/platforms which only need to set a clock rate.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
"The PM core always increments the runtime usage counter
before calling the ->suspend() callback and decrements it
after calling the ->resume() callback"
DPU and DSI are managed as runtime devices. When
suspend is triggered, PM core adds a refcount on all the
devices and calls device suspend, since usage count is
already incremented, runtime suspend was not getting called
and it kept the clocks on which resulted in target not
entering into XO shutdown.
Add changes to force suspend on runtime devices during pm sleep.
Changes in v1:
- Remove unnecessary checks in the function
_dpu_kms_disable_dpu (Rob Clark).
Changes in v2:
- Avoid using suspend_late to reset the usagecount
as suspend_late might not be called during suspend
call failures (Doug).
Changes in v3:
- Use force suspend instead of managing device usage_count
via runtime put and get API's to trigger callbacks (Doug).
Changes in v4:
- Check the return values of pm_runtime_force_suspend and
pm_runtime_force_resume API's and pass appropriately (Doug).
Changes in v5:
- With v4 patch, test cycle has uncovered issues in device resume.
On bubs: cmd tx failures were seen as SW is sending panel off
commands when the dsi resources are turned off.
Upon suspend, DRM driver will issue a NULL composition to the
dpu, followed by turning off all the HW blocks.
v5 changes will serialize the NULL commit and resource unwinding
by handling them under PM prepare and PM complete phases there by
ensuring that clks are on when panel off commands are being
processed.
Changes in v6:
- Use drm_mode_config_helper_suspend/resume() instead of legacy API
drm_atomic_helper_suspend/resume() (Doug).
Trigger runtime callbacks from the suspend/resume call to turn
off the resources.
Changes in v7:
- Add "__maybe_unused" to the functions to avoid compilation
failures. Cleanup unnecessary configs (Doug).
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Spelling out _unlocked for each and every driver is a annoying.
Especially if we consider how many drivers, do not know (or need to)
about the horror stories involving struct_mutex.
Just drop the suffix. It makes the API cleaner.
Done via the following script:
__from=drm_gem_object_put_unlocked
__to=drm_gem_object_put
for __file in $(git grep --name-only $__from); do
sed -i "s/$__from/$__to/g" $__file;
done
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200515095118.2743122-25-emil.l.velikov@gmail.com
|
|
Requested my mripard for some misc patches that need this as a base.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Most bridge drivers create a DRM connector to model the connector at the
output of the bridge. This model is historical and has worked pretty
well so far, but causes several issues:
- It prevents supporting more complex display pipelines where DRM
connector operations are split over multiple components. For instance a
pipeline with a bridge connected to the DDC signals to read EDID data,
and another one connected to the HPD signal to detect connection and
disconnection, will not be possible to support through this model.
- It requires every bridge driver to implement similar connector
handling code, resulting in code duplication.
- It assumes that a bridge will either be wired to a connector or to
another bridge, but doesn't support bridges that can be used in both
positions very well (although there is some ad-hoc support for this in
the analogix_dp bridge driver).
In order to solve these issues, ownership of the connector should be
moved to the display controller driver (where it can be implemented
using helpers provided by the core).
Extend the bridge API to allow disabling connector creation in bridge
drivers as a first step towards the new model. The new flags argument to
the bridge .attach() operation allows instructing the bridge driver to
skip creating a connector. Unconditionally set the new flags argument to
0 for now to keep the existing behaviour, and modify all existing bridge
drivers to return an error when connector creation is not requested as
they don't support this feature yet.
The change is based on the following semantic patch, with manual review
and edits.
@ rule1 @
identifier funcs;
identifier fn;
@@
struct drm_bridge_funcs funcs = {
...,
.attach = fn
};
@ depends on rule1 @
identifier rule1.fn;
identifier bridge;
statement S, S1;
@@
int fn(
struct drm_bridge *bridge
+ , enum drm_bridge_attach_flags flags
)
{
... when != S
+ if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) {
+ DRM_ERROR("Fix bridge driver to make connector optional!");
+ return -EINVAL;
+ }
+
S1
...
}
@ depends on rule1 @
identifier rule1.fn;
identifier bridge, flags;
expression E1, E2, E3;
@@
int fn(
struct drm_bridge *bridge,
enum drm_bridge_attach_flags flags
) {
<...
drm_bridge_attach(E1, E2, E3
+ , flags
)
...>
}
@@
expression E1, E2, E3;
@@
drm_bridge_attach(E1, E2, E3
+ , 0
)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-10-laurent.pinchart@ideasonboard.com
|
|
For a given byte clock, if VCO recalc value is exactly same as
vco set rate value, vco_set_rate does not get called assuming
VCO is already set to required value. But Due to GDSC toggle,
VCO values are erased in the HW. To make sure VCO is programmed
correctly, we forcefully call set_rate from vco_prepare.
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Save pll state before dsi host is powered off. Without this change
some register values gets resetted.
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
I was hitting kCFI crashes when building with clang, and after
some digging finally narrowed it down to the
dsi_mgr_connector_mode_valid() function being implemented as
returning an int, instead of an enum drm_mode_status.
This patch fixes it, and appeases the opaque word of the kCFI
gods (seriously, clang inlining everything makes the kCFI
backtraces only really rough estimates of where things went
wrong).
Thanks as always to Sami for his help narrowing this down.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Sami Tolvanen <samitolvanen@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Alistair Delva <adelva@google.com>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: freedreno@lists.freedesktop.org
Cc: clang-built-linux@googlegroups.com
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"There are a few changes to the core framework this time around, in
addition to the normal collection of driver updates to support new
SoCs, fix incorrect data, and convert various drivers to clk_hw based
APIs.
In the core, we allow clk_ops::init() to return an error code now so
that we can fail clk registration if the callback does something like
fail to allocate memory. We also add a new "terminate" clk_op so that
things done in clk_ops::init() can be undone, e.g. free memory. We
also spit out a warning now when critical clks fail to enable and we
support changing clk rates and enable/disable state through debugfs
when developers compile the kernel themselves.
On the driver front, we get support for what seems like a lot of
Qualcomm and NXP SoCs given that those vendors dominate the diffstat.
There are a couple new drivers for Xilinx and Amlogic SoCs too. The
updates are all small things like fixing the way glitch free muxes
switch parents, avoiding div-by-zero problems, or fixing data like
parent names. See the updates section below for more details.
Finally, the "basic" clk types have been converted to support
specifying parents with clk_hw pointers. This work includes an
overhaul of the fixed-rate clk type to be more modern by using clk_hw
APIs.
Core:
- Let clk_ops::init() return an error code
- Add a clk_ops::terminate() callback to undo clk_ops::init()
- Warn about critical clks that fail to enable or prepare
- Support dangerous debugfs actions on clks with dead code
New Drivers:
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Add a driver for BCLK of Freescale SAI cores
- Add cam, vpe and sgx clock support for TI dra7
- Add aess clock support for TI omap5
- Enable clks for CPUfreq on Allwinner A64 SoCs
- Add Amlogic meson8b DDR clock controller
- Add input clocks to Amlogic meson8b controllers
- Add SPIBSC (SPI FLASH) clock on Renesas RZ/A2
- i.MX8MP clk driver support
Updates:
- Convert gpio, fixed-factor, mux, gate, divider basic clks to hw
based APIs
- Detect more PRMCU variants in ux500 driver
- Adjust the composite clk type to new way of describing clk parents
- Fixes for clk controllers on qcom msm8998 SoCs
- Fix gmac main clock for TI dra7
- Move TI dra7-atl clock header to correct location
- Fix hidden node name dependency on TI clkctrl clocks
- Fix Amlogic meson8b mali clock update using the glitch free mux
- Fix Amlogic pll driver division by zero at init
- Prepare for split of Renesas R-Car H3 ES1.x and ES2.0+ config
symbols
- Switch more i.MX clk drivers to clk_hw based APIs
- Disable non-functional divider between pll4_audio_div and
pll4_post_div on imx6q
- Fix watchdog2 clock name typo in imx7ulp clock driver
- Set CLK_GET_RATE_NOCACHE flag for DRAM related clocks on i.MX8M
SoCs
- Suppress bind attrs for i.MX8M clock driver
- Add a big comment in imx8qxp-lpcg driver to tell why
devm_platform_ioremap_resource() shouldn't be used for the driver
- A correction on i.MX8MN usb1_ctrl parent clock setting"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (140 commits)
dt/bindings: clk: fsl,plldig: Drop 'bindings' from schema id
clk: ls1028a: Fix warning on clamp() usage
clk: qoriq: add ls1088a hwaccel clocks support
clk: ls1028a: Add clock driver for Display output interface
dt/bindings: clk: Add YAML schemas for LS1028A Display Clock bindings
clk: fsl-sai: new driver
dt-bindings: clock: document the fsl-sai driver
clk: composite: add _register_composite_pdata() variants
clk: qcom: rpmh: Sort OF match table
dt-bindings: fix warnings in validation of qcom,gcc.yaml
dt-binding: fix compilation error of the example in qcom,gcc.yaml
clk: zynqmp: Add support for clock with CLK_DIVIDER_POWER_OF_TWO flag
clk: zynqmp: Fix divider calculation
clk: zynqmp: Add support for get max divider
clk: zynqmp: Warn user if clock user are more than allowed
clk: zynqmp: Extend driver for versal
dt-bindings: clock: Add bindings for versal clock driver
clk: ti: clkctrl: Fix hidden dependency to node name
clk: ti: add clkctrl data dra7 sgx
clk: ti: omap5: Add missing AESS clock
...
|
|
https://gitlab.freedesktop.org/drm/msm into drm-next
+ sc7180 display + DSI support
+ a618 (sc7180) support
+ more UBWC (bandwidth compression) support
+ various cleanups to handle devices that use vs don't
use zap fw, etc
+ usual random cleanups and fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ <CAF6AEGvv03ifuP0tp7-dmqZtr1iS=s8Vc=az8BNGtEoSMD-dkw@mail.gmail.com
|
|
LANE_CTRL register in latest version of DSI controller (v2.2)
has additional functionality introduced to enable/disable HS
signalling with default value set to enabled. To accommodate this
change, LANE_CTRL register should be read and bit wise ORed to enable
non continuous clock mode. Without this change, if register is written
directly, HS signalling will be disabled resulting in black screen.
Changes in v1:
-Update LANE_CTRL register value
Changes in v2:
-Changing commit message accordingly.
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Add support for v2.4.1 DSI block in the sc7180 SoC.
Changes in v1:
-Modify commit text to indicate DSI version and SOC detail(Jeffrey Hugo).
-Splitting visionox panel driver code out into a
different patch(set), since panel drivers are merged into
drm-next via a different tree(Rob Clark).
Changes in v2:
-Update commit text accordingly(Matthias Kaehlcke).
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
[cleanup subject / commit message]
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
After commit fc0c209c147f ("clk: Allow parents to be specified without
string names") we can use DT or direct clk_hw pointers to specify
parents. Create a generic function that shouldn't be used very often to
encode the multitude of ways of registering a mux clk with different
parent information. Then add a bunch of wrapper macros that only pass
down what needs to be passed down to the generic function to support
this with less arguments.
Note: the msm drm driver passes an anonymous array through the macro
which seems to confuse my compiler. Adding a parenthesis around the
whole thing at the call site seems to fix it but it must be wrong. Maybe
it's better to split this patch and pick out the array bits there?
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190830150923.259497-11-sboyd@kernel.org
|
|
Decouple enable and rate setting. Prep work to handle bootloader
enabled display.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
|
|
At the moment, the MSM DSI driver calls drm_panel_enable() rather early
from the DSI bridge pre_enable() function. At this point, the encoder
(e.g. MDP5) is not enabled, so we have not started transmitting
video data.
However, the drm_panel_funcs documentation states that enable()
should be called on the panel *after* video data is being transmitted:
The .prepare() function is typically called before the display controller
starts to transmit video data. [...] After the display controller has
started transmitting video data, it's safe to call the .enable() function.
This will typically enable the backlight to make the image on screen visible.
Calling drm_panel_enable() too early causes problems for some panels:
The TFT LCD panel used in the Samsung Galaxy Tab A 9.7 (2015) (APQ8016)
uses the MIPI_DCS_SET_DISPLAY_BRIGHTNESS command to control
backlight/brightness of the screen. The enable sequence is therefore:
drm_panel_enable()
drm_panel_funcs.enable():
backlight_enable()
backlight_ops.update_status():
mipi_dsi_dcs_set_display_brightness(dsi, bl->props.brightness);
The panel seems to silently ignore the MIPI_DCS_SET_DISPLAY_BRIGHTNESS
command if it is sent too early. This prevents setting the initial brightness,
causing the display to be enabled with minimum brightness instead.
Adding various delays in the panel initialization code does not result
in any difference.
On the other hand, moving drm_panel_enable() to dsi_mgr_bridge_enable()
fixes the problem, indicating that the panel requires the video stream
to be active before the brightness command is accepted.
Therefore: Move drm_panel_enable() to dsi_mgr_bridge_enable() to
delay calling it until video data is being transmitted.
Move drm_panel_disable() to dsi_mgr_bridge_disable() for similar reasons.
(This is not strictly required for the panel affected above...)
Tested-by: Jasper Korten <jja2000@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Tested-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.6:
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ba73535a-9334-5302-2e1f-5208bd7390bd@linux.intel.com
|
|
To facilitate moving connector creation to display drivers,
decouple the drm_connector from drm_panel.
This patch adds a connector argument to drm_panel_get_modes().
All users of drm_panel_get_modes() already had the connector
available, so updating users was trivial.
With this patch drm_panel no longer keeps a reference to the drm_connector.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alison Wang <alison.wang@nxp.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Torsten Duwe <duwe@lst.de>
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Cc: Alexios Zavras <alexios.zavras@intel.com>
Cc: Brian Masney <masneyb@onstation.org>
Cc: Rob Clark <robdclark@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Allison Randal <allison@lohutok.net>
Cc: Shayenne Moura <shayenneluzmoura@gmail.com>
Cc: Abhinav Kumar <abhinavk@codeaurora.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-tegra@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20191207140353.23967-7-sam@ravnborg.org
|
|
https://gitlab.freedesktop.org/drm/msm into drm-next
+ OCMEM support to enable the couple generations that had shared OCMEM
rather than GMEM exclusively for the GPU (late a3xx and I think basically
all of a4xx). Bjorn and Brian decided to land this through the drm
tree to avoid having to coordinate merge requests.
+ a510 support, and various associated display support
+ the usual misc cleanups and fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ <CAF6AEGv-JWswEJRxe5AmnGQO1SZnpxK05kO1E29K6UUzC9GMMw@mail.gmail.com
|
|
MSM8976, MSM8976 and APQ variants have DSI version 3:10040002
(DSI 6G V1.4.2), featuring two DSIs.
They need three clocks (mdp_core, iface, bus), one GDSC and
two vregs, VDDA at 1.2V and VDDIO at 1.8V.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The 28nm PLL has a different iospace on MSM/APQ family B SoCs:
add a new configuration and use it when the DT reports the
"qcom,dsi-phy-28nm-hpm-fam-b" compatible.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The DSI PHY regulator supports two regulator modes: LDO and DCDC.
This mode can be selected using the "qcom,dsi-phy-regulator-ldo-mode"
device tree property.
However, at the moment only the 20nm PHY driver actually implements
that option. Add a check in the 28nm PHY driver to program the
registers correctly for LDO mode.
Tested-by: Nikita Travkin <nikitos.tr@gmail.com> # l8150
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191023165617.28738-1-stephan@gerhold.net
|
|
Thierry needs fd70c7755bf0 ("drm/bridge: tc358767: fix max_tu_symbol
value") to be able to merge his dp_link patch series.
Some adjacent changes conflicts, plus some clashes in i915 due to
cherry-picking and git trying to be helpful and leaving both versions
in.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
On msm8998, vblank timeouts are observed because the DSI controller is not
reset properly, which ends up stalling the MDP. This is because the reset
logic is not correct per the hardware documentation.
The documentation states that after asserting reset, software should wait
some time (no indication of how long), or poll the status register until it
returns 0 before deasserting reset.
wmb() is insufficient for this purpose since it just ensures ordering, not
timing between writes. Since asserting and deasserting reset occurs on the
same register, ordering is already guaranteed by the architecture, making
the wmb extraneous.
Since we would define a timeout for polling the status register to avoid a
possible infinite loop, lets just use a static delay of 20 ms, since 16.666
ms is the time available to process one frame at 60 fps.
Fixes: a689554ba6ed ("drm/msm: Initial add DSI connector support")
Cc: Hai Li <hali@codeaurora.org>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Sean Paul <sean@poorly.run>
[seanpaul renamed RESET_DELAY to DSI_RESET_TOGGLE_DELAY_MS]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191011133939.16551-1-jeffrey.l.hugo@gmail.com
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/msm/dsi/dsi_host.c: In function dsi_cmd_dma_rx:
drivers/gpu/drm/msm/dsi/dsi_host.c:1302:7: warning: variable lp set but not used [-Wunused-but-set-variable]
It is not used since commit a689554ba6ed ("drm/msm:
Initial add DSI connector support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1570690506-83287-5-git-send-email-zhengbin13@huawei.com
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/msm/dsi/phy/dsi_phy.c: In function msm_dsi_dphy_timing_calc_v2:
drivers/gpu/drm/msm/dsi/phy/dsi_phy.c:156:17: warning: variable lpx set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/msm/dsi/phy/dsi_phy.c: In function msm_dsi_dphy_timing_calc_v3:
drivers/gpu/drm/msm/dsi/phy/dsi_phy.c:273:17: warning: variable lpx set but not used [-Wunused-but-set-variable]
'lpx' in msm_dsi_dphy_timing_calc_v2 is not used since commit a4df68fa232e
("drm/msm/dsi: Add new method to calculate 14nm PHY timings")
'lpx' in msm_dsi_dphy_timing_calc_v3 is not used since commit f1fa7ff44056
("drm/msm/dsi: implement auto PHY timing calculator for 10nm PHY")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1570690506-83287-4-git-send-email-zhengbin13@huawei.com
|
|
Move the static keyword to the front of declarations
of msm_dsi_v2_host_ops, msm_dsi_6g_host_ops and
msm_dsi_6g_v2_host_ops, and resolve the following
compiler warnings that can be seen when building
with warnings enabled (W=1):
drivers/gpu/drm/msm/dsi/dsi_cfg.c:150:1: warning:
‘static’ is not at beginning of declaration [-Wold-style-declaration]
drivers/gpu/drm/msm/dsi/dsi_cfg.c:161:1: warning:
‘static’ is not at beginning of declaration [-Wold-style-declaration]
drivers/gpu/drm/msm/dsi/dsi_cfg.c:172:1: warning:
‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
We haven't done any backmerge for a while due to the merge window, and it
starts to become an issue for komeda. Let's bring 5.4-rc1 in.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
clk_get_parent returns an error pointer upon failure, not NULL. So the
checks as they exist won't catch a failure. This patch changes the
checks and the return values to properly handle an error pointer.
Fixes: c4d8cfe516dc ("drm/msm/dsi: add implementation for helper functions")
Cc: Sibi Sankar <sibis@codeaurora.org>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Rob Clark <robdclark@chromium.org>
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The following errors show up when booting the Nexus 5:
msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR*
dsi_phy_regulator_init: failed to init regulator, ret=-517
msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR*
dsi_phy_driver_probe: failed to init regulator
dsi_phy_regulator_init() already logs the error, so no need to log
the same error a second time in dsi_phy_driver_probe(). This patch
also changes dsi_phy_regulator_init() to not log the error if the
error code is -EPROBE_DEFER to reduce noise in dmesg.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[add some {}'s]
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
This DSI driver uses the new descriptor API so these old
GPIO API includes are surplus.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Drop the deprecated drmP.h header file, and trim msm_drv.h
to the relevant include files.
This resulted in a suprisingly many edits as many files relied
on headers included via msm_drv.h.
But msm_drv.h is not supposed to carry include files it do not need, so
the individual files have to include what extra they needs.
v2:
- Rebased on top of https://gitlab.freedesktop.org/drm/msm.git msm-next
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Bruce Wang <bzwang@chromium.org>
Cc: Shayenne Moura <shayenneluzmoura@gmail.com>
Cc: Mamta Shukla <mamtashukla555@gmail.com>
Cc: Jonathan Marek <jonathan@marek.ca>
Cc: Carsten Behling <carsten.behling@googlemail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Cc: Sibi Sankar <sibis@codeaurora.org>
Cc: Todor Tomov <todor.tomov@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190804065551.GA5211@ravnborg.org
|
|
We are about to add a drm_bridge_state that inherits from
drm_private_state which is defined in drm_atomic.h. Problem is,
drm_atomic.h includes drm_crtc.h which in turn includes drm_bridge.h,
leading to "drm_private_state has incomplete type" error.
Let's force all users of the drm_bridge API to explicitly include
drm_bridge.h.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190826152649.13820-2-boris.brezillon@collabora.com
|
|
https://gitlab.freedesktop.org/drm/msm into drm-next
+ usual progress on cleanups
+ dsi vs EPROBE_DEFER fixes
+ msm8998 (snapdragon 835 support)
+ a540 gpu support (mesa support already landed)
+ dsi, dsi-phy support
+ mdp5 and dpu interconnect (bus/memory scaling) support
+ initial prep work for per-context pagetables (at least the parts that
don't have external dependencies like iommu/arm-smmu)
There is one more patch for fixing DSI cmd mode panels (part of a set of
patches to get things working on nexus5), but it would be conflicty with
1cff7440a86e04a613665803b42034 in drm-next without rebasing or back-merge,
and since it doesn't conflict with anything in msm-next, I think it best
if Sean merges that through drm-mix-fixes instead.
(In other news, I've been making some progress w/ getting efifb working
properly on sdm850 laptop without horrible hacks, and drm/msm + clk stuff
not totally falling over when bootloader enables display and things are
already running when driver probes.. but not quite ready yet, hopefully
we can post some of that for 5.4.. should help for both the sdm835 and
sdm850 laptops.)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGsj3N4XzDLSDoa+4RHZ9wXObYmhcep0M3LjnRg48BeLvg@mail.gmail.com
|
|
Now that the panel probe/setup is in the modeset path, we can call
dsi_manager_setup_encoder() in a common place for both internal and
external bridge setups.
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617201301.133275-10-sean@poorly.run
|
|
Since deferred probe from the modeset init path now works, we can move
the panel initialization from detect() into connector init. This
avoids doing work in detect() and hopefully will result in a more
deterministic boot sequence between devices with a dsi panel, and those
with an external bridge.
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617201301.133275-9-sean@poorly.run
|
|
Now that we have a function to call set_encoder_mode() for us, use it.
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617201301.133275-8-sean@poorly.run
|
|
This patch moves things around a bit to be a little more readable and
pulls out the set_encoder_mode() call into its own function for later
use.
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617201301.133275-7-sean@poorly.run
|
|
Pull all of the panel init code out of detect() and put it in its own
function. This will be useful in future patches where it's moved from
detect().
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617201301.133275-6-sean@poorly.run
|
|
It's a bit dangerous to store the flags in msm_dsi since there's no way to
tell when they're populated. Fortunately the only place that uses them
is the same place that fills them. So just use a local variable and
delete the struct member.
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617201301.133275-5-sean@poorly.run
|
|
We use the flags in more places than just get_panel, so split them out
into a separate function.
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617201301.133275-4-sean@poorly.run
|
