| Age | Commit message (Collapse) | Author |
|---|
|
I need this to be able to apply the deferred fbdev setup patches, I
need the relevant prep work that landed through the drm-intel tree.
Also squash in conflict fixup from Laurent Pinchart.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Once a client has requested a waitboost, we keep that waitboost active
until all clients are no longer waiting. This is because we don't
distinguish which waiter deserves the boost. However, with the advent of
fence signaling, the signaler threads appear as waiters to the RPS
interrupt handler. So instead of using a single boolean to track when to
keep the waitboost active, use a counter of all outstanding waitboosted
requests.
At this point, I have removed all vestiges of the rate limiting on
clients. Whilst this means that compositors should remain more fluid,
it also means that boosts are more prevalent. See commit b29c19b64528
("drm/i915: Boost RPS frequency for CPU stalls") for a longer discussion
on the pros and cons of both approaches.
A drawback of this implementation is that it requires constant request
submission to keep the waitboost trimmed (as it is now cancelled when the
request is completed). This will be fine for a busy system, but near
idle the boosts may be kept for longer than desired (effectively tens of
vblanks worstcase) and there is a reliance on rc6 instead.
v2: Remove defunct rps.client_lock
Reported-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170628123548.9236-1-chris@chris-wilson.co.uk
|
|
Required for Daniel's drm_vblank_cleanup cleanup
|
|
Trying to do a modeset from within a reset is fraught with danger. We
can fall into a cyclic deadlock where the modeset is waiting on a
previous modeset that is waiting on a request, and since the GPU hung
that request completion is waiting on the reset. As modesetting doesn't
allow its locks to be broken and restarted, or for its *own* reset
mechanism to take over the display, we have to do something very
evil instead. If we detect that we are stuck waiting to prepare the
display reset (by using a very simple timeout), resort to cancelling all
in-flight requests and throwing the user data into /dev/null, which is
marginally better than the driver locking up and keeping that data to
itself.
This is not a fix; this is just a workaround that unbreaks machines
until we can resolve the deadlock in a way that doesn't lose data!
v2: Move the retirement from set-wegded to the i915_reset() error path,
after which we no longer any delayed worker cleanup for
i915_handle_error()
v3: C abuse for syntactic sugar
v4: Cover all waits with the timeout to catch more driver breakage
References: https://bugs.freedesktop.org/show_bug.cgi?id=99093
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170622105625.16952-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
This is a preparatory patch which modifies error handler to do per engine
hang recovery. The actual patch which implements this sequence follows
later in the series. The aim is to prepare existing recovery function to
adapt to this new function where applicable (which fails at this point
because core implementation is lacking) and continue recovery using legacy
full gpu reset.
A helper function is also added to query the availability of engine
reset. A subsequent patch will add the capability to query which type
of reset is present (engine -> full -> no-reset) via the get-param
ioctl.
It has been decided that the error events that are used to notify user of
reset will only be sent in case if full chip reset. In case of just
single (or multiple) engine resets, userspace won't be notified by these
events.
Note that this implementation of engine reset is for i915 directly
submitting to the ELSP, where the driver manages the hang detection,
recovery and resubmission. With GuC submission these tasks are shared
between driver and firmware; i915 will still responsible for detecting a
hang, and when it does it will have to request GuC to reset that Engine and
remind the firmware about the outstanding submissions. This will be
added in different patch.
v2: rebase, advertise engine reset availability in platform definition,
add note about GuC submission.
v3: s/*engine_reset*/*reset_engine*/. (Chris)
Handle reset as 2 level resets, by first going to engine only and fall
backing to full/chip reset as needed, i.e. reset_engine will need the
struct_mutex.
v4: Pass the engine mask to i915_reset. (Chris)
v5: Rebase, update selftests.
v6: Rebase, prepare for mutex-less reset engine.
v7: Pass reset_engine mask as a function parameter, and iterate over the
engine mask for reset_engine. (Chris)
v8: Use i915.reset >=2 in has_reset_engine; remove redundant reset
logging; add a reset-engine-in-progress flag to prevent concurrent
resets, and avoid dual purposing of reset-backoff. (Chris)
v9: Support reset of different engines in parallel (Chris)
v10: Handle reset-engine flag locking better (Chris)
v11: Squash in reporting of per-engine-reset availability.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Ian Lister <ian.lister@intel.com>
Signed-off-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615201828.23144-4-michel.thierry@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620095751.13127-5-chris@chris-wilson.co.uk
|
|
If we enter i915_handle_error() a second time and a global reset is
already in progress, we can simply wait for completion of the first
reset. Currently we exit early prior to the actual reset being
performed -- the worst of both worlds!
v2: Plug into the existing reset_queue, and remember that kselftests is
playing games with I915_RESET_BACKOFF to prevent hangcheck from screwing
up.
v3: Rename to i915_reset_device to fit in better with i915_reset_engine
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620095751.13127-2-chris@chris-wilson.co.uk
|
|
We use drm_crtc_ for all the new-style vblank functions which directly
take a struct drm_crtc *. drm_accurate_vblank_count was the odd one
out, correct this to appease my OCD.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170524145212.27837-13-daniel.vetter@ffwll.ch
|
|
Most of south engine display that is in PCH is still the
same as SPT and KBP, except for this key differences:
- Backlight: Backlight programming changed in CNP PCH.
- Panel Power: Sligh programming changed in CNP PCH.
- GMBUS and GPIO: The pin mapping has changed in CNP PCH.
All of these changes follow more the BXT style.
v2: Update definition to use dev_priv isntead of dev (Tvrtko).
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496434004-29812-1-git-send-email-rodrigo.vivi@intel.com
|
|
git://anongit.freedesktop.org/git/drm-intel into drm-next
More stuff for 4.13:
- skl+ wm fixes from Mahesh Kumar
- some refactor and tests for i915_sw_fence (Chris)
- tune execlist/scheduler code (Chris)
- g4x,g33 gpu reset improvements (Chris, Mika)
- guc code cleanup (Michal Wajdeczko, Michał Winiarski)
- dp aux backlight improvements (Puthikorn Voravootivat)
- buffer based guc/host communication (Michal Wajdeczko)
* tag 'drm-intel-next-2017-05-29' of git://anongit.freedesktop.org/git/drm-intel: (253 commits)
drm/i915: Update DRIVER_DATE to 20170529
drm/i915: Keep the forcewake timer alive for 1ms past the most recent use
drm/i915/guc: capture GuC logs if FW fails to load
drm/i915/guc: Introduce buffer based cmd transport
drm/i915/guc: Disable send function on fini
drm: Add definition for eDP backlight frequency
drm/i915: Drop AUX backlight enable check for backlight control
drm/i915: Consolidate #ifdef CONFIG_INTEL_IOMMU
drm/i915: Only GGTT vma may be pinned and prevent shrinking
drm/i915: Serialize GTT/Aperture accesses on BXT
drm/i915: Convert i915_gem_object_ops->flags values to use BIT()
drm/i915/selftests: Silence compiler warning in igt_ctx_exec
drm/i915/guc: Skip port assign on first iteration of GuC dequeue
drm/i915: Remove misleading comment in request_alloc
drm/i915/g33: Improve reset reliability
Revert "drm/i915: Restore lost "Initialized i915" welcome message"
drm/i915/huc: Update GLK HuC version
drm/i915: Check for allocation failure
drm/i915/guc: Remove action status and statistics from debugfs
drm/i915/g4x: Improve gpu reset reliability
...
|
|
Since we coordinate with the execlists tasklet using a locked schedule
operation that ensures that after we set the engine->irq_posted we
always have an invocation of the tasklet, we do not need to use a locked
operation to set the engine->irq_posted itself.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170517121007.27224-12-chris@chris-wilson.co.uk
|
|
As the handler is now quite complex, involving a few atomics, the cost
of the function preamble is negligible in comparison and so we should
leave the function out-of-line for better I$.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170517121007.27224-11-chris@chris-wilson.co.uk
|
|
If we *know* that the engine is idle, i.e. we have not more contexts in
flight, we can skip any spurious CSB idle interrupts. These spurious
interrupts seem to arrive long after we assert that the engines are
completely idle, triggering later assertions:
[ 178.896646] intel_engine_is_idle(bcs): interrupt not handled, irq_posted=2
[ 178.896655] ------------[ cut here ]------------
[ 178.896658] kernel BUG at drivers/gpu/drm/i915/intel_engine_cs.c:226!
[ 178.896661] invalid opcode: 0000 [#1] SMP
[ 178.896663] Modules linked in: i915(E) x86_pkg_temp_thermal(E) crct10dif_pclmul(E) crc32_pclmul(E) crc32c_intel(E) ghash_clmulni_intel(E) nls_ascii(E) nls_cp437(E) vfat(E) fat(E) intel_gtt(E) i2c_algo_bit(E) drm_kms_helper(E) syscopyarea(E) sysfillrect(E) sysimgblt(E) fb_sys_fops(E) aesni_intel(E) prime_numbers(E) evdev(E) aes_x86_64(E) drm(E) crypto_simd(E) cryptd(E) glue_helper(E) mei_me(E) mei(E) lpc_ich(E) efivars(E) mfd_core(E) battery(E) video(E) acpi_pad(E) button(E) tpm_tis(E) tpm_tis_core(E) tpm(E) autofs4(E) i2c_i801(E) fan(E) thermal(E) i2c_designware_platform(E) i2c_designware_core(E)
[ 178.896694] CPU: 1 PID: 522 Comm: gem_exec_whispe Tainted: G E 4.11.0-rc5+ #14
[ 178.896702] task: ffff88040aba8d40 task.stack: ffffc900003f0000
[ 178.896722] RIP: 0010:intel_engine_init_global_seqno+0x1db/0x1f0 [i915]
[ 178.896725] RSP: 0018:ffffc900003f3ab0 EFLAGS: 00010246
[ 178.896728] RAX: 0000000000000000 RBX: ffff88040af54000 RCX: 0000000000000000
[ 178.896731] RDX: ffff88041ec933e0 RSI: ffff88041ec8cc48 RDI: ffff88041ec8cc48
[ 178.896734] RBP: ffffc900003f3ac8 R08: 0000000000000000 R09: 000000000000047d
[ 178.896736] R10: 0000000000000040 R11: ffff88040b344f80 R12: 0000000000000000
[ 178.896739] R13: ffff88040bce0000 R14: ffff88040bce52d8 R15: ffff88040bce0000
[ 178.896742] FS: 00007f2cccc2d8c0(0000) GS:ffff88041ec80000(0000) knlGS:0000000000000000
[ 178.896746] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 178.896749] CR2: 00007f41ddd8f000 CR3: 000000040bb03000 CR4: 00000000001406e0
[ 178.896752] Call Trace:
[ 178.896768] reset_all_global_seqno.part.33+0x4e/0xd0 [i915]
[ 178.896782] i915_gem_request_alloc+0x304/0x330 [i915]
[ 178.896795] i915_gem_do_execbuffer+0x8a1/0x17d0 [i915]
[ 178.896799] ? remove_wait_queue+0x48/0x50
[ 178.896812] ? i915_wait_request+0x300/0x590 [i915]
[ 178.896816] ? wake_up_q+0x70/0x70
[ 178.896819] ? refcount_dec_and_test+0x11/0x20
[ 178.896823] ? reservation_object_add_excl_fence+0xa5/0x100
[ 178.896835] i915_gem_execbuffer2+0xab/0x1f0 [i915]
[ 178.896844] drm_ioctl+0x1e6/0x460 [drm]
[ 178.896858] ? i915_gem_execbuffer+0x260/0x260 [i915]
[ 178.896862] ? dput+0xcf/0x250
[ 178.896866] ? full_proxy_release+0x66/0x80
[ 178.896869] ? mntput+0x1f/0x30
[ 178.896872] do_vfs_ioctl+0x8f/0x5b0
[ 178.896875] ? ____fput+0x9/0x10
[ 178.896878] ? task_work_run+0x80/0xa0
[ 178.896881] SyS_ioctl+0x3c/0x70
[ 178.896885] entry_SYSCALL_64_fastpath+0x17/0x98
[ 178.896888] RIP: 0033:0x7f2ccb455ca7
[ 178.896890] RSP: 002b:00007ffcabec72d8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
[ 178.896894] RAX: ffffffffffffffda RBX: 000055f897a44b90 RCX: 00007f2ccb455ca7
[ 178.896897] RDX: 00007ffcabec74a0 RSI: 0000000040406469 RDI: 0000000000000003
[ 178.896900] RBP: 00007f2ccb70a440 R08: 00007f2ccb70d0a4 R09: 0000000000000000
[ 178.896903] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
[ 178.896905] R13: 000055f89782d71a R14: 00007ffcabecf838 R15: 0000000000000003
[ 178.896908] Code: 00 31 d2 4c 89 ef 8d 70 48 41 ff 95 f8 06 00 00 e9 68 fe ff ff be 0f 00 00 00 48 c7 c7 48 dc 37 a0 e8 fa 33 d6 e0 e9 0b ff ff ff <0f> 0b 0f 0b 0f 0b 0f 0b 0f 1f 00 66 2e 0f 1f 84 00 00 00 00 00
On the other hand, by ignoring the interrupt do we risk running out of
space in CSB ring? Testing for a few hours suggests not, i.e. that we
only seem to get the odd delayed CSB idle notification.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170517121007.27224-6-chris@chris-wilson.co.uk
|
|
In the previous patch we've implemented hwmode tracking a la i915 for
the vblank timestamp calculations. But that was just the basic
semantics, i915 has some nice sanity checks to make sure we keep
getting this right. Move them over too.
v2:
- WARN_ON_ONCE to avoid excessive spam (Ville)
- Really only WARN on atomic drivers.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170509140329.24114-5-daniel.vetter@ffwll.ch
|
|
If we restrict this helper to only kms drivers (which is the case) we
can look up the correct mode easily ourselves. But it's a bit tricky:
- All legacy drivers look at crtc->hwmode. But that is updated already
at the beginning of the modeset helper, which means when we disable
a pipe. Hence the final timestamps might be a bit off. But since
this is an existing bug I'm not going to change it, but just try to
be bug-for-bug compatible with the current code. This only applies
to radeon&amdgpu.
- i915 tries to get it perfect by updating crtc->hwmode when the pipe
is off (i.e. vblank->enabled = false).
- All other atomic drivers look at crtc->state->adjusted_mode. Those
that look at state->requested_mode simply don't adjust their mode,
so it's the same. That has two problems: Accessing crtc->state from
interrupt handling code is unsafe, and it's updated before we shut
down the pipe. For nonblocking modesets it's even worse.
For atomic drivers try to implement what i915 does. To do that we add
a new hwmode field to the vblank structure, and update it from
drm_calc_timestamping_constants(). For atomic drivers that's called
from the right spot by the helper library already, so all fine. But
for safety let's enforce that.
For legacy driver this function is only called at the end (oh the
fun), which is broken, so again let's not bother and just stay
bug-for-bug compatible.
The benefit is that we can use drm_calc_vbltimestamp_from_scanoutpos
directly to implement ->get_vblank_timestamp in every driver, deleting
a lot of code.
v2: Completely new approach, trying to mimick the i915 solution.
v3: Fixup kerneldoc.
v4: Drop the WARN_ON to check that the vblank is off, atomic helpers
currently unconditionally call this. Recomputing the same stuff should
be harmless.
v5: Fix typos and move misplaced hunks to the right patches (Neil).
v6: Undo hunk movement (kbuild).
Cc: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Cc: Eric Anholt <eric@anholt.net>
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170509140329.24114-4-daniel.vetter@ffwll.ch
|
|
It's overkill to have a flag parameter which is essentially used just
as a boolean. This takes care of core + adjusting drivers.
Adjusting the scanout position callback is a bit harder, since radeon
also supplies it's own driver-private flags in there.
v2: Fixup misplaced hunks (Neil).
v3: kbuild says v1 was better ...
Cc: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Cc: Eric Anholt <eric@anholt.net>
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170509140329.24114-2-daniel.vetter@ffwll.ch
|
|
There's really no reason for anything more:
- Calling this while the crtc vblank stuff isn't set up is a driver
bug. Those places alrready DRM_ERROR.
- Calling this when the crtc is off is either a driver bug (calling
drm_crtc_handle_vblank at the wrong time) or a core bug (for
anything else). Again, we DRM_ERROR.
- EINVAL is checked at higher levels already, and if we'd use struct
drm_crtc * instead of (dev, pipe) it would be real obvious that
those are again core bugs.
The only valid failure mode is crap hardware that couldn't sample a
useful timestamp, to ask the core to just grab a not-so-accurate
timestamp. Bool is perfectly fine for that.
v2: Also fix up the one caller, I lost that in the shuffling (Jani).
v3: Fixup commit message (Neil).
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Cc: Eric Anholt <eric@anholt.net>
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170509140329.24114-1-daniel.vetter@ffwll.ch
|
|
vlv_display_irq_postinstall() enables the LPE audio interrupts
regardless of whether the LPE audio irq chip has masked/unmasked
them. Also the irqchip masking/unmasking doesn't consider the state
of the display power well or the device, and hence just leads to
dmesg spew when it tries to access the hardware while it's powered
down.
If the current way works, then we don't need to do anything in the
mask/unmask hooks. If it doesn't work, well, then we'd need to properly
track whether the irqchip has masked/unmasked the interrupts when
we enable display interrupts. And the mask/unmask hooks would need
to check whether display interrupts are even enabled before frobbing
with he registers.
So let's just assume the current way works and neuter the mask/unmask
hooks. Also clean up vlv_display_irq_postinstall() a bit and stop
it from trying to unmask/enable the LPE C interrupt on VLV since it
doesn't exist.
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170427160231.13337-4-ville.syrjala@linux.intel.com
Reviewed-by: Takashi Iwai <tiwai@suse.de>
|
|
Add intel_irq_fini() for placing the deinitialization code,
starting with freeing dev_priv->l3_parity.remap_info[].
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1493366319-18515-1-git-send-email-joonas.lahtinen@linux.intel.com
|
|
Previously with commit a9c1f90c8e17
("drm/i915: Don't mask EI UP interrupt on IVB|SNB") certain,
seemingly unrelated bit (GEN6_PM_RP_UP_EI_EXPIRED) was needed
to be unmasked for IVB and SNB in order to prevent system hang
with chained batchbuffers.
Our CI was seeing incomplete results with tests that used
chained batches and it was found out that HSW needs to have this
same bit unmasked to reliably survive chained batches.
Always unmask GEN6_PM_RP_UP_EI_EXPIRED on Haswell to
prevent system hang with batch chaining.
Testcase: igt/gem_exec_fence/nb-await-default
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100672
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1492082127-29007-1-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 3396a273851c14634b98bb27be37508b06df94f4)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Previously with commit a9c1f90c8e17
("drm/i915: Don't mask EI UP interrupt on IVB|SNB") certain,
seemingly unrelated bit (GEN6_PM_RP_UP_EI_EXPIRED) was needed
to be unmasked for IVB and SNB in order to prevent system hang
with chained batchbuffers.
Our CI was seeing incomplete results with tests that used
chained batches and it was found out that HSW needs to have this
same bit unmasked to reliably survive chained batches.
Always unmask GEN6_PM_RP_UP_EI_EXPIRED on Haswell to
prevent system hang with batch chaining.
Testcase: igt/gem_exec_fence/nb-await-default
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100672
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1492082127-29007-1-git-send-email-mika.kuoppala@intel.com
|
|
Backmerge drm-next to get at -rc4, which we need to land the 4.12 gvt
patches.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
Linux 4.11-rc4
The i915 GVT team need the rc4 code to base some more code on.
|
|
When initializing the GuC log struct, there is an object we need to
allocate always, since the GuC needs its address at fw load time.
The rest is only needed during runtime, in the sense that we only
create if we actually enable GuC logging. Make that distinction
explicit by subdividing further the intel_guc_log struct.
v2: Call the new struct "runtime", instead of "extras" (Joonas)
v3: Check indent (Joonas)
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
I915_RESET_IN_PROGRESS is being used for both signaling the requirement
to i915_mutex_lock_interruptible() to avoid taking the struct_mutex and
to instruct a waiter (already holding the struct_mutex) to perform the
reset. To allow for a little more coordination, split these two meaning
into a couple of distinct flags. I915_RESET_BACKOFF tells
i915_mutex_lock_interruptible() not to acquire the mutex and
I915_RESET_HANDOFF tells the waiter to call i915_reset().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170316171305.12972-1-chris@chris-wilson.co.uk
|
|
This emulates execlists on top of the GuC in order to defer submission of
requests to the hardware. This deferral allows time for high priority
requests to gazump their way to the head of the queue, however it nerfs
the GuC by converting it back into a simple execlist (where the CPU has
to wake up after every request to feed new commands into the GuC).
v2: Drop hack status - though iirc there is still a lockdep inversion
between fence and engine->timeline->lock (which is impossible as the
nesting only occurs on different fences - hopefully just requires some
judicious lockdep annotation)
v3: Apply lockdep nesting to enabling signaling on the request, using
the pattern we already have in __i915_gem_request_submit();
v4: Replaying requests after a hang also now needs the timeline
spinlock, to disable the interrupts at least
v5: Hold wq lock for completeness, and emit a tracepoint for enabling signal
v6: Reorder interrupt checking for a happier gcc.
v7: Only signal the tasklet after a user-interrupt if using guc scheduling
v8: Restore lost update of rq through the i915_guc_irq_handler (Tvrtko)
v9: Avoid re-initialising the engine->irq_tasklet from inside a reset
v10: Hook up the execlists-style tracepoints
v11: Clear the execlists irq_posted bit after taking over the interrupt/tasklet
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170316125619.6856-1-chris@chris-wilson.co.uk
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
|
|
Set byt rc residency counters high level as chv does by
default. We lose some accuracy on byt but we can do the calculation
without extra hw read on both platforms, as now they behave
identically in this respect.
v2: use ktime
v3: keep comparison u32 (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1489592584-10422-1-git-send-email-mika.kuoppala@intel.com
|
|
We have used cz timestamp register to gain a reference time wrt
to residency calculations. The residency counts are in cz clk ticks
(333Mhz clock) but for some reason the cz timestamp register gives
100us units. Perhaps for some other usage, the base-ten based values
are easier, but in residency calculations raw units would have been
the easiest.
As there is not much advantage of using base-ten clock through
a more costly punit access, take our reference times directly from
kernel clock.
v2: use ktime (Chris, Ville)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Check that request has not been signaled before acquiring a reference to
the request for signaling later in the interrupt handler.
The loading of the cacheline (for request->fence.flags) should be "free"
when followed by the locked increment of the request->fence.refcount
(which then sets the cacheline to exclusive mode), i.e. the cost of
test_bit prior to an atomic_inc should be negligible. This should
benefit us when we have a pile of bare breadcrumbs (interrupted execbuf)
where we may get interrupts faster than we can get rid of the
intel_wait, or if the device is too slow to run the bottom-half between
interrupts.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170315210726.12095-5-chris@chris-wilson.co.uk
|
|
We take the runtime pm wakelock during i915_handle_error() to ensure
that all paths that reach the error handler keep the device awake during
the hw reads. However, we need to extend that from the reset handler to
include the earlier capture routines.
Reported-by: Antonio Argenziano <antonio.argenziano@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170314171840.25706-1-chris@chris-wilson.co.uk
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
|
|
On Baytrail, we manually calculate busyness over the evaluation interval
to avoid issues with miscaluations with RC6 enabled. However, it turns
out that the DOWN_EI interrupt generator is completely bust - it
operates in two modes, continuous or never. Neither of which are
conducive to good behaviour. Stop unmask the DOWN_EI interrupt and just
compute everything from the UP_EI which does seem to correspond to the
desired interval.
v2: Fixup gen6_rps_pm_mask() as well
v3: Inline vlv_c0_above() to combine the now identical elapsed
calculation for up/down and simplify the threshold testing
Fixes: 43cf3bf084ba ("drm/i915: Improved w/a for rps on Baytrail")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.1+
Link: http://patchwork.freedesktop.org/patch/msgid/20170309211232.28878-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170313170617.31564-1-chris@chris-wilson.co.uk
(cherry picked from commit e0e8c7cb6eb68e9256de2d8cbeb481d3701c05ac)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
In order to prevent accessing the hpd registers outside of the display
power wells, we should refrain from writing to the registers before the
display interrupts are enabled.
[ 4.740136] WARNING: CPU: 1 PID: 221 at drivers/gpu/drm/i915/intel_uncore.c:795 __unclaimed_reg_debug+0x44/0x50 [i915]
[ 4.740155] Unclaimed read from register 0x1e1110
[ 4.740168] Modules linked in: i915(+) intel_gtt drm_kms_helper prime_numbers
[ 4.740190] CPU: 1 PID: 221 Comm: systemd-udevd Not tainted 4.10.0-rc6+ #384
[ 4.740203] Hardware name: / , BIOS PYBSWCEL.86A.0027.2015.0507.1758 05/07/2015
[ 4.740220] Call Trace:
[ 4.740236] dump_stack+0x4d/0x6f
[ 4.740251] __warn+0xc1/0xe0
[ 4.740265] warn_slowpath_fmt+0x4a/0x50
[ 4.740281] ? insert_work+0x77/0xc0
[ 4.740355] ? fwtable_write32+0x90/0x130 [i915]
[ 4.740431] __unclaimed_reg_debug+0x44/0x50 [i915]
[ 4.740507] fwtable_read32+0xd8/0x130 [i915]
[ 4.740575] i915_hpd_irq_setup+0xa5/0x100 [i915]
[ 4.740649] intel_hpd_init+0x68/0x80 [i915]
[ 4.740716] i915_driver_load+0xe19/0x1380 [i915]
[ 4.740784] i915_pci_probe+0x32/0x90 [i915]
[ 4.740799] pci_device_probe+0x8b/0xf0
[ 4.740815] driver_probe_device+0x2b6/0x450
[ 4.740828] __driver_attach+0xda/0xe0
[ 4.740841] ? driver_probe_device+0x450/0x450
[ 4.740853] bus_for_each_dev+0x5b/0x90
[ 4.740865] driver_attach+0x19/0x20
[ 4.740878] bus_add_driver+0x166/0x260
[ 4.740892] driver_register+0x5b/0xd0
[ 4.740906] ? 0xffffffffa0166000
[ 4.740920] __pci_register_driver+0x47/0x50
[ 4.740985] i915_init+0x5c/0x5e [i915]
[ 4.740999] do_one_initcall+0x3e/0x160
[ 4.741015] ? __vunmap+0x7c/0xc0
[ 4.741029] ? kmem_cache_alloc+0xcf/0x120
[ 4.741045] do_init_module+0x55/0x1c4
[ 4.741060] load_module+0x1f3f/0x25b0
[ 4.741073] ? __symbol_put+0x40/0x40
[ 4.741086] ? kernel_read_file+0x100/0x190
[ 4.741100] SYSC_finit_module+0xbc/0xf0
[ 4.741112] SyS_finit_module+0x9/0x10
[ 4.741125] entry_SYSCALL_64_fastpath+0x17/0x98
[ 4.741135] RIP: 0033:0x7f8559a140f9
[ 4.741145] RSP: 002b:00007fff7509a3e8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[ 4.741161] RAX: ffffffffffffffda RBX: 00007f855aba02d1 RCX: 00007f8559a140f9
[ 4.741172] RDX: 0000000000000000 RSI: 000055b6db0914f0 RDI: 0000000000000011
[ 4.741183] RBP: 0000000000020000 R08: 0000000000000000 R09: 000000000000000e
[ 4.741193] R10: 0000000000000011 R11: 0000000000000246 R12: 000055b6db0854d0
[ 4.741204] R13: 000055b6db091150 R14: 0000000000000000 R15: 000055b6db035924
v2: Set dev_priv->display_irqs_enabled to true for all platforms other
than vlv/chv that manually control the display power domain.
Fixes: 19625e85c6ec ("drm/i915: Enable polling when we don't have hpd")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97798
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lyude <cpaul@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Hans de Goede <jwrdegoede@fedoraproject.org>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170215131547.5064-1-chris@chris-wilson.co.uk
Link: http://patchwork.freedesktop.org/patch/msgid/20170313170231.18633-1-chris@chris-wilson.co.uk
(cherry picked from commit 262fd485ac6b476479f41f00bb104f6a1766ae66)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Replace __raw_i915_read32() with I915_READ_FW() in the workaround for
the SKL+ scanline counter hardware fail. The two are the same thing
but everyone else uses I915_READ_FW() so let's follow suit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170309154434.29303-3-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
Optimize the multi-register read in i915_get_vblank_counter() a little
bit by grabbing the uncore lock manually and using I915_READ_FW().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170309154434.29303-2-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
gen6_sanitize_rps_pm_mask() is small enough that inlining it shrinks the
object code.
v2: Use const markup
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170312135426.2216-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
|
The REDIRECT_TO_GUC bit is a strange beast as it is a disable bit -
setting the bit in the pm interrupt generation stops the interrupt going
to the guc (not sending it to the guc as the name implies). To help the
reader rename it to DISABLE_REDIRECT_TO_GUC so that we keep the bspec
greppable name without it being as confusing!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170312132745.9618-1-chris@chris-wilson.co.uk
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
|
|
Different state is to be maintained for rps.pm_intrmsk_mbz for GuC and
Execlists. Updating it inside guc_interrupts_* routines as in those
routines GuC load/submission params are sanitized and it should not be set
based on HAS_GUC_SCHED during intel_irq_init.
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1489199821-6707-3-git-send-email-sagar.a.kamble@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
"pm_intr_keep" is not conveying the intent that it is bitmask
of interrupts that must be zero(mbz) in GEN6_PMINTRMSK.
Name it "pm_intrmsk_mbz".
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1489199821-6707-2-git-send-email-sagar.a.kamble@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
To make our adjustments to RPS requires taking a mutex and potentially
sleeping for an unknown duration - until we have completed our
adjustments further RPS interrupts are immaterial (they are based on
stale thresholds) and we can safely ignore them.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170309211232.28878-3-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
|
|
Currently, we sum the render and media cycles (on different engines) to
compute a percentage - but we fail to factor in the duplication into the
threshold calculations. This makes us very eager to upclock!
If we just consider the maximum busy cycles of either counter, we should
have an accurate reflection on whether there are cycles to spare to
handle the workload at this frequency.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170309211232.28878-2-chris@chris-wilson.co.uk
|
|
On Baytrail, we manually calculate busyness over the evaluation interval
to avoid issues with miscaluations with RC6 enabled. However, it turns
out that the DOWN_EI interrupt generator is completely bust - it
operates in two modes, continuous or never. Neither of which are
conducive to good behaviour. Stop unmask the DOWN_EI interrupt and just
compute everything from the UP_EI which does seem to correspond to the
desired interval.
v2: Fixup gen6_rps_pm_mask() as well
v3: Inline vlv_c0_above() to combine the now identical elapsed
calculation for up/down and simplify the threshold testing
Fixes: 43cf3bf084ba ("drm/i915: Improved w/a for rps on Baytrail")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.1+
Link: http://patchwork.freedesktop.org/patch/msgid/20170309211232.28878-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
|
|
Driver needs to ensure that it doesn't mask the PM interrupts, which are
unmasked/needed by GuC firmware. For that, Driver maintains a bitmask of
interrupts to be kept unmasked, pm_intr_keep.
pm_intr_keep was determined across GuC load. GuC gets loaded in different
scenarios and it is not going to change the pm_intr_keep so this patch
moves its setup to intel_irq_init.
This patch fixes incorrect RPS masking leading to UP interrupts triggered
even when at cur_freq=max and inversly for Down interrupts.
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1488862355-9768-1-git-send-email-sagar.a.kamble@intel.com
|
|
git://anongit.freedesktop.org/git/drm-intel into drm-next
4 weeks worth of stuff since I was traveling&lazy:
- lspcon improvements (Imre)
- proper atomic state for cdclk handling (Ville)
- gpu reset improvements (Chris)
- lots and lots of polish around fences, requests, waiting and
everything related all over (both gem and modeset code), from Chris
- atomic by default on gen5+ minus byt/bsw (Maarten did the patch to
flip the default, really this is a massive joint team effort)
- moar power domains, now 64bit (Ander)
- big pile of in-kernel unit tests for various gem subsystems (Chris),
including simple mock objects for i915 device and and the ggtt
manager.
- i915_gpu_info in debugfs, for taking a snapshot of the current gpu
state. Same thing as i915_error_state, but useful if the kernel didn't
notice something is stick. From Chris.
- bxt dsi fixes (Umar Shankar)
- bxt w/a updates (Jani)
- no more struct_mutex for gem object unreference (Chris)
- some execlist refactoring (Tvrtko)
- color manager support for glk (Ander)
- improve the power-well sync code to better take over from the
firmware (Imre)
- gem tracepoint polish (Tvrtko)
- lots of glk fixes all around (Ander)
- ctx switch improvements (Chris)
- glk dsi support&fixes (Deepak M)
- dsi fixes for vlv and clanups, lots of them (Hans de Goede)
- switch to i915.ko types in lots of our internal modeset code (Ander)
- byt/bsw atomic wm update code, yay (Ville)
* tag 'drm-intel-next-2017-03-06' of git://anongit.freedesktop.org/git/drm-intel: (432 commits)
drm/i915: Update DRIVER_DATE to 20170306
drm/i915: Don't use enums for hardware engine id
drm/i915: Split breadcrumbs spinlock into two
drm/i915: Refactor wakeup of the next breadcrumb waiter
drm/i915: Take reference for signaling the request from hardirq
drm/i915: Add FIFO underrun tracepoints
drm/i915: Add cxsr toggle tracepoint
drm/i915: Add VLV/CHV watermark/FIFO programming tracepoints
drm/i915: Add plane update/disable tracepoints
drm/i915: Kill level 0 wm hack for VLV/CHV
drm/i915: Workaround VLV/CHV sprite1->sprite0 enable underrun
drm/i915: Sanitize VLV/CHV watermarks properly
drm/i915: Only use update_wm_{pre,post} for pre-ilk platforms
drm/i915: Nuke crtc->wm.cxsr_allowed
drm/i915: Compute proper intermediate wms for vlv/cvh
drm/i915: Skip useless watermark/FIFO related work on VLV/CHV when not needed
drm/i915: Compute vlv/chv wms the atomic way
drm/i915: Compute VLV/CHV FIFO sizes based on the PM2 watermarks
drm/i915: Plop vlv/chv fifo sizes into crtc state
drm/i915: Plop vlv wm state into crtc_state
...
|
|
git://anongit.freedesktop.org/git/drm-misc into drm-next
First slice of drm-misc-next for 4.12:
Core/subsystem-wide:
- link status core patch from Manasi, for signalling link train fail
to userspace. I also had the i915 patch in here, but that had a
small buglet in our CI, so reverted.
- more debugfs_remove removal from Noralf, almost there now (Noralf
said he'll try to follow up with the stragglers).
- drm todo moved into kerneldoc, for better visibility (see
Documentation/gpu/todo.rst), lots of starter tasks in there.
- devm_ of helpers + use it in sti (from Ben Gaignard, acked by Rob
Herring)
- extended framebuffer fbdev support (for fbdev flipping), and vblank
wait ioctl fbdev support (Maxime Ripard)
- misc small things all over, as usual
- add vblank callbacks to drm_crtc_funcs, plus make lots of good use
of this to simplify drivers (Shawn Guo)
- new atomic iterator macros to unconfuse old vs. new state
Small drivers:
- vc4 improvements from Eric
- vc4 kerneldocs (Eric)!
- tons of improvements for dw-mipi-dsi in rockchip from John Keeping
and Chris Zhong.
- MAINTAINERS entries for drivers managed in drm-misc. It's not yet
official, still an experiment, but definitely not complete fail and
better to avoid confusion. We kinda screwed that up with drm-misc a
bit when we started committers last year.
- qxl atomic conversion (Gabriel Krisman)
- bunch of virtual driver polish (qxl, virgl, ...)
- misc tiny patches all over
This is the first time we've done the same merge-window blackout for
drm-misc as we've done for drm-intel for ages, hence why we have a
_lot_ of stuff queued already. But it's still only half of drm-intel
(room to grow!), and the drivers in drm-misc experiment seems to work
at least insofar as that you also get lots of driver updates here
alredy.
* tag 'drm-misc-next-2017-03-06' of git://anongit.freedesktop.org/git/drm-misc: (141 commits)
drm/vc4: Fix OOPSes from trying to cache a partially constructed BO.
drm/vc4: Fulfill user BO creation requests from the kernel BO cache.
Revert "drm/i915: Implement Link Rate fallback on Link training failure"
drm/fb-helper: implement ioctl FBIO_WAITFORVSYNC
drm: Update drm_fbdev_cma_init documentation
drm/rockchip/dsi: add dw-mipi power domain support
drm/rockchip/dsi: fix insufficient bandwidth of some panel
dt-bindings: add power domain node for dw-mipi-rockchip
drm/rockchip/dsi: remove mode_valid function
drm/rockchip/dsi: dw-mipi: correct the coding style
drm/rockchip/dsi: dw-mipi: support RK3399 mipi dsi
dt-bindings: add rk3399 support for dw-mipi-rockchip
drm/rockchip: dw-mipi-dsi: add reset control
drm/rockchip: dw-mipi-dsi: support non-burst modes
drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded
drm/rockchip: vop: test for P{H,V}SYNC
drm/rockchip: dw-mipi-dsi: use positive check for N{H, V}SYNC
drm/rockchip: dw-mipi-dsi: use specific poll helper
drm/rockchip: dw-mipi-dsi: improve PLL configuration
drm/rockchip: dw-mipi-dsi: properly configure PHY timing
...
|
|
As we now take the breadcrumbs spinlock within the interrupt handler, we
wish to minimise its hold time. During the interrupt we do not care
about the state of the full rbtree, only that of the first element, so
we can guard that with a separate lock.
v2: Rename first_wait to irq_wait to make it clearer that it is guarded
by irq_lock.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303190824.1330-1-chris@chris-wilson.co.uk
|
|
Being inside a spinlock signaling that the hardware just completed a
request doesn't prevent a second thread already spotting that the
request is complete, freeing it and reallocating it! The code currently
tries to prevent this using RCU -- but that only prevents the request
from being freed, it doesn't prevent us from reallocating it - that
requires us to take a reference.
[ 206.922985] BUG: spinlock already unlocked on CPU#4, gem_exec_parall/7796
[ 206.922994] lock: 0xffff8801c6047120, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
[ 206.923000] CPU: 4 PID: 7796 Comm: gem_exec_parall Not tainted 4.10.0-CI-Patchwork_4008+ #1
[ 206.923006] Hardware name: System manufacturer System Product Name/Z170M-PLUS, BIOS 1805 06/20/2016
[ 206.923012] Call Trace:
[ 206.923014] <IRQ>
[ 206.923019] dump_stack+0x67/0x92
[ 206.923023] spin_dump+0x73/0xc0
[ 206.923027] do_raw_spin_unlock+0x79/0xb0
[ 206.923031] _raw_spin_unlock_irqrestore+0x27/0x60
[ 206.923042] dma_fence_signal+0x160/0x230
[ 206.923060] notify_ring+0xae/0x2e0 [i915]
[ 206.923073] ? ibx_hpd_irq_handler+0xc0/0xc0 [i915]
[ 206.923086] gen8_gt_irq_handler+0x219/0x290 [i915]
[ 206.923100] gen8_irq_handler+0x8e/0x6b0 [i915]
[ 206.923105] __handle_irq_event_percpu+0x58/0x370
[ 206.923109] handle_irq_event_percpu+0x1e/0x50
[ 206.923113] handle_irq_event+0x34/0x60
[ 206.923117] handle_edge_irq+0xbe/0x150
[ 206.923122] handle_irq+0x15/0x20
[ 206.923126] do_IRQ+0x63/0x130
[ 206.923142] ? i915_mutex_lock_interruptible+0x39/0x140 [i915]
[ 206.923148] common_interrupt+0x90/0x90
[ 206.923153] RIP: 0010:osq_lock+0x77/0x110
[ 206.923157] RSP: 0018:ffffc90001cabaa0 EFLAGS: 00000246 ORIG_RAX: ffffffffffffff6e
[ 206.923164] RAX: 0000000000000000 RBX: ffff880236d1abc0 RCX: ffff8801ef642fc0
[ 206.923169] RDX: ffff8801ef6427c0 RSI: ffffffff81c6e7fd RDI: ffffffff81c7c848
[ 206.923175] RBP: ffffc90001cabab8 R08: 00000000692bb19b R09: 08c1493200000000
[ 206.923180] R10: 0000000000000001 R11: 0000000000000001 R12: ffff880236cdabc0
[ 206.923185] R13: ffff8802207f00b0 R14: ffffffffa00b7cd9 R15: ffff8802207f0070
[ 206.923191] </IRQ>
[ 206.923206] ? i915_mutex_lock_interruptible+0x39/0x140 [i915]
[ 206.923213] __mutex_lock+0x649/0x990
[ 206.923217] ? __mutex_lock+0xb0/0x990
[ 206.923221] ? _raw_spin_unlock+0x2c/0x50
[ 206.923226] ? __pm_runtime_resume+0x56/0x80
[ 206.923242] ? i915_mutex_lock_interruptible+0x39/0x140 [i915]
[ 206.923249] mutex_lock_interruptible_nested+0x16/0x20
[ 206.923264] i915_mutex_lock_interruptible+0x39/0x140 [i915]
[ 206.923270] ? __pm_runtime_resume+0x56/0x80
[ 206.923285] i915_gem_do_execbuffer.isra.15+0x442/0x1d10 [i915]
[ 206.923291] ? __lock_acquire+0x449/0x1b50
[ 206.923296] ? __might_fault+0x3e/0x90
[ 206.923301] ? __might_fault+0x87/0x90
[ 206.923305] ? __might_fault+0x3e/0x90
[ 206.923320] i915_gem_execbuffer2+0xb5/0x220 [i915]
[ 206.923327] drm_ioctl+0x200/0x450
[ 206.923341] ? i915_gem_execbuffer+0x330/0x330 [i915]
[ 206.923348] do_vfs_ioctl+0x90/0x6e0
[ 206.923352] ? __fget+0x108/0x200
[ 206.923356] ? expand_files+0x2b0/0x2b0
[ 206.923361] SyS_ioctl+0x3c/0x70
[ 206.923365] entry_SYSCALL_64_fastpath+0x1c/0xb1
[ 206.923369] RIP: 0033:0x7fdd75fc6357
[ 206.923373] RSP: 002b:00007fdd20e59bf8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
[ 206.923380] RAX: ffffffffffffffda RBX: ffffffff81481ff3 RCX: 00007fdd75fc6357
[ 206.923385] RDX: 00007fdd20e59c70 RSI: 0000000040406469 RDI: 0000000000000003
[ 206.923390] RBP: ffffc90001cabf88 R08: 0000000000000040 R09: 00000000000003f7
[ 206.923396] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
[ 206.923401] R13: 0000000000000003 R14: 0000000040406469 R15: 0000000001cf9cb0
[ 206.923408] ? __this_cpu_preempt_check+0x13/0x20
Fixes: 56299fb7d904 ("drm/i915: Signal first fence from irq handler if complete")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100051
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303144557.4815-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
|
|
Add tracepoints for plane programming. The tracepoints will dump
the frame and scanline counters, so this can be used to verify eg. that
the plane gets reprogrammed at the right time with respect to watermark
programming (if we have appropriate tracepoints for that as well).
v2: Rebase due to legacy cursor changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-16-ville.syrjala@linux.intel.com
|
|
assert_spin_locked() becomes an unconditionally compiled BUG_ON(),
adding debug code right into the heart of critical routines like
interrupt handlers.
text data bss dec hex
1296480 19944 2272 1318696 141f28 before (lockdep disabled)
1295984 19944 2272 1318200 141d38 after
1336261 21139 3208 1360608 14c2e0 before (lockdep enabled)
1339920 21139 3208 1364267 14d12b after
Small saving for release; hopefully more instructive in debug.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302132801.599-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
A significant cost in setting up a wait is the overhead of enabling the
interrupt. As we disable the interrupt whenever the queue of waiters is
empty, if we are frequently waiting on alternating batches, we end up
re-enabling the interrupt on a frequent basis. We do want to disable the
interrupt during normal operations as under high load it may add several
thousand interrupts/s - we have been known in the past to occupy whole
cores with our interrupt handler after accidentally leaving user
interrupts enabled. As a compromise, leave the interrupt enabled until
the next IRQ, or the system is idle. This gives a small window for a
waiter to keep the interrupt active and not be delayed by having to
re-enable the interrupt.
v2: Restore hangcheck/missed-irq detection for continuations
v3: Be more careful restoring the hangcheck timer after reset
v4: Be more careful restoring the fake irq after reset (if required!)
v5: Redo changes to intel_engine_wakeup()
v6: Factor out __intel_engine_wakeup()
v7: Improve commentary for declaring a missed wakeup
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170227205850.2828-4-chris@chris-wilson.co.uk
|
|
As execlists and other non-semaphore multi-engine devices coordinate
between engines using interrupts, we can shave off a few 10s of
microsecond of scheduling latency by doing the fence signaling from the
interrupt as opposed to a RT kthread. (Realistically the delay adds
about 1% to an individual cross-engine workload.) We only signal the
first fence in order to limit the amount of work we move into the
interrupt handler. We also have to remember that our breadcrumbs may be
unordered with respect to the interrupt and so we still require the
waiter process to perform some heavyweight coherency fixups, as well as
traversing the tree of waiters.
v2: No need for early exit in irq handler - it breaks the flow between
patches and prevents the tracepoint
v3: Restore rcu hold across irq signaling of request
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170227205850.2828-2-chris@chris-wilson.co.uk
|
|
Backmerge the main pull request to sync up with all the newly landed
drivers. Otherwise we'll have chaos even before 4.12 started in
earnest.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
