| Age | Commit message (Collapse) | Author |
|---|
|
Some object retain an extra pin whilst they are active (e.g. contexts).
This excludes them from being considered for eviction unless we idle the
GPU. If before we look at the active list, we retire beforehand we can
hopefully remove a few excess pins and reduce the amount of searching
required.
v2: Similar principle applies to evict_for_vma
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20161209150555.602-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
Soft-pinning depends upon being able to check for availabilty of an
interval and evict overlapping object from a drm_mm range manager very
quickly. Currently it uses a linear list, and so performance is dire and
not suitable as a general replacement. Worse, the current code will oops
if it tries to evict an active buffer.
It also helps if the routine reports the correct error codes as expected
by its callers and emits a tracepoint upon use.
For posterity since the wrong patch was pushed (i.e. that missed these
key points and had known bugs), this is the changelog that should have
been on commit 506a8e87d8d2 ("drm/i915: Add soft-pinning API for
execbuffer"):
Userspace can pass in an offset that it presumes the object is located
at. The kernel will then do its utmost to fit the object into that
location. The assumption is that userspace is handling its own object
locations (for example along with full-ppgtt) and that the kernel will
rarely have to make space for the user's requests.
This extends the DRM_IOCTL_I915_GEM_EXECBUFFER2 to do the following:
* if the user supplies a virtual address via the execobject->offset
*and* sets the EXEC_OBJECT_PINNED flag in execobject->flags, then
that object is placed at that offset in the address space selected
by the context specifier in execbuffer.
* the location must be aligned to the GTT page size, 4096 bytes
* as the object is placed exactly as specified, it may be used by this
execbuffer call without relocations pointing to it
It may fail to do so if:
* EINVAL is returned if the object does not have a 4096 byte aligned
address
* the object conflicts with another pinned object (either pinned by
hardware in that address space, e.g. scanouts in the aliasing ppgtt)
or within the same batch.
EBUSY is returned if the location is pinned by hardware
EINVAL is returned if the location is already in use by the batch
* EINVAL is returned if the object conflicts with its own alignment (as meets
the hardware requirements) or if the placement of the object does not fit
within the address space
All other execbuffer errors apply.
Presence of this execbuf extension may be queried by passing
I915_PARAM_HAS_EXEC_SOFTPIN to DRM_IOCTL_I915_GETPARAM and checking for
a reported value of 1 (or greater).
v2: Combine the hole/adjusted-hole ENOSPC checks
v3: More color, more splitting, more blurb.
Fixes: 506a8e87d8d2 ("drm/i915: Add soft-pinning API for execbuffer")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161205142941.21965-2-chris@chris-wilson.co.uk
|
|
99% of the time we access i915_address_space->dev we want the i915
device and not the drm device, so let's store the drm_i915_private
backpointer instead. The only real complication here are the inlines
in i915_vma.h where drm_i915_private is not yet defined and so we have
to choose an alternate path for our asserts.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161129095008.32622-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
With the infrastructure converted over to tracking multiple timelines in
the GEM API whilst preserving the efficiency of using a single execution
timeline internally, we can now assign a separate timeline to every
context with full-ppgtt.
v2: Add a comment to indicate the xfer between timelines upon submission.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161028125858.23563-35-chris@chris-wilson.co.uk
|
|
Add lockdep_assert_held(struct_mutex) to the API preamble of the
internal GEM interfaces.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161028125858.23563-9-chris@chris-wilson.co.uk
|
|
We want to decouple RPM and struct_mutex, but currently RPM has to walk
the list of bound objects and remove userspace mmapping before we
suspend (otherwise userspace may continue to access the GTT whilst it is
powered down). This currently requires the struct_mutex to walk the
bound_list, but if we move that to a separate list and lock we can take
the first step towards removing the struct_mutex.
v2: Split runtime suspend unmapping vs regular unmapping, to make the
locking (and barriers) clearer. Add the object to the userfault_list
prior to inserting the first PTE, the race between add/revoke depends
upon struct_mutex for regular unmappings and rpm for runtime-suspend.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> #v1
Link: http://patchwork.freedesktop.org/patch/msgid/20161024124218.18252-1-chris@chris-wilson.co.uk
|
|
With the possibility of addition of many more number of rings in future,
the drm_i915_private structure could bloat as an array, of type
intel_engine_cs, is embedded inside it.
struct intel_engine_cs engine[I915_NUM_ENGINES];
Though this is still fine as generally there is only a single instance of
drm_i915_private structure used, but not all of the possible rings would be
enabled or active on most of the platforms. Some memory can be saved by
allocating intel_engine_cs structure only for the enabled/active engines.
Currently the engine/ring ID is kept static and dev_priv->engine[] is simply
indexed using the enums defined in intel_engine_id.
To save memory and continue using the static engine/ring IDs, 'engine' is
defined as an array of pointers.
struct intel_engine_cs *engine[I915_NUM_ENGINES];
dev_priv->engine[engine_ID] will be NULL for disabled engine instances.
There is a text size reduction of 928 bytes, from 1028200 to 1027272, for
i915.o file (but for i915.ko file text size remain same as 1193131 bytes).
v2:
- Remove the engine iterator field added in drm_i915_private structure,
instead pass a local iterator variable to the for_each_engine**
macros. (Chris)
- Do away with intel_engine_initialized() and instead directly use the
NULL pointer check on engine pointer. (Chris)
v3:
- Remove for_each_engine_id() macro, as the updated macro for_each_engine()
can be used in place of it. (Chris)
- Protect the access to Render engine Fault register with a NULL check, as
engine specific init is done later in Driver load sequence.
v4:
- Use !!dev_priv->engine[VCS] style for the engine check in getparam. (Chris)
- Kill the superfluous init_engine_lists().
v5:
- Cleanup the intel_engines_init() & intel_engines_setup(), with respect to
allocation of intel_engine_cs structure. (Chris)
v6:
- Rebase.
v7:
- Optimize the for_each_engine_masked() macro. (Chris)
- Change the type of 'iter' local variable to enum intel_engine_id. (Chris)
- Rebase.
v8: Rebase.
v9: Rebase.
v10:
- For index calculation use engine ID instead of pointer based arithmetic in
intel_engine_sync_index() as engine pointers are not contiguous now (Chris)
- For appropriateness, rename local enum variable 'iter' to 'id'. (Joonas)
- Use for_each_engine macro for cleanup in intel_engines_init() and remove
check for NULL engine pointer in cleanup() routines. (Joonas)
v11: Rebase.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1476378888-7372-1-git-send-email-akash.goel@intel.com
|
|
In the next patch we want to handle reset directly by a locked waiter in
order to avoid issues with returning before the reset is handled. To
handle the reset, we must first know whether we hold the struct_mutex.
If we do not hold the struct_mtuex we can not perform the reset, but we do
not block the reset worker either (and so we can just continue to wait for
request completion) - otherwise we must relinquish the mutex.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160909131201.16673-10-chris@chris-wilson.co.uk
|
|
We need finer control over wakeup behaviour during i915_wait_request(),
so expand the current bool interruptible to a bitmask.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160909131201.16673-9-chris@chris-wilson.co.uk
|
|
Often times we do not want to evict mapped objects from the GGTT as
these are quite expensive to teardown and frequently reused (causing an
equally, if not more so, expensive setup). In particular, when faulting
in a new object we want to avoid evicting an active object, or else we
may trigger a page-fault-of-doom as we ping-pong between evicting two
objects.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160818161718.27187-26-chris@chris-wilson.co.uk
|
|
The principal motivation for this was to try and eliminate the
struct_mutex from i915_gem_suspend - but we still need to hold the mutex
current for the i915_gem_context_lost(). (The issue there is that there
may be an indirect lockdep cycle between cpu_hotplug (i.e. suspend) and
struct_mutex via the stop_machine().) For the moment, enabling last
request tracking for the engine, allows us to do busyness checking and
waiting without requiring the struct_mutex - which is useful in its own
right.
As a side-effect of having a robust means for tracking engine busyness,
we can replace our other busyness heuristic, that of comparing against
the last submitted seqno. For paranoid reasons, we have a semi-ordered
check of that seqno inside the hangchecker, which we can now improve to
an ordered check of the engine's busyness (removing a locked xchg in the
process).
v2: Pass along "bool interruptible" as being unlocked we cannot rely on
i915->mm.interruptible being stable or even under our control.
v3: Replace check Ironlake i915_gpu_busy() with the common precalculated value
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-6-git-send-email-chris@chris-wilson.co.uk
|
|
In the next few patches, the VMA pinning API is overhauled and to reduce
the churn we pull out the update to the accessors into a prep patch.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-14-git-send-email-chris@chris-wilson.co.uk
|
|
This is not the full fix, as we are required to percolate the u64 nature
down through the drm_mm stack, but this is required now to prevent
explosions due to mismatch between execbuf (eb_vma_misplaced) and vma
binding (i915_vma_misplaced) - and reduces the risk of spurious changes
as we adjust the vma interface in the next patches.
v2: long long casts not required for u64 printk (%llx)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-6-git-send-email-chris@chris-wilson.co.uk
|
|
Eviction is VM local, so we can ignore the significance of the
drm_device in the caller, and leave it to i915_gem_evict_something() to
manage itself.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-2-git-send-email-chris@chris-wilson.co.uk
|
|
Slight micro-optimise to produce combine loops so that gcc is able to
optimise the inner-loops concisely. Since we are reviewing the loops, we
can update the comments to describe the current state of affairs, in
particular the distinction between evicting from the global GTT (which
may contain untracked items and transient global pins) and the
per-process GTT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-1-git-send-email-chris@chris-wilson.co.uk
|
|
In order to prevent a leak of the vma on shared objects, we need to
hook into the object_close callback to destroy the vma on the object for
this file. However, if we destroyed that vma immediately we may cause
unexpected application stalls as we try to unbind a busy vma - hence we
defer the unbind to when we retire the vma.
v2: Keep vma allocated until closed. This is useful for a later
optimisation, but it is required now in order to handle potential
recursion of i915_vma_unbind() by retiring itself.
v3: Comments are important.
Testcase: igt/gem_ppggtt/flink-and-close-vma-leak
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470293567-10811-26-git-send-email-chris@chris-wilson.co.uk
|
|
Ultimately wraps kref_put(), so adopt its nomenclature for consistency
with other subsystems.
s/drm_gem_object_unreference/i915_gem_object_put/
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1469005202-9659-6-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469017917-15134-5-git-send-email-chris@chris-wilson.co.uk
|
|
Ultimately wraps kref_get(), so adopt its nomenclature for consistency
with other subsystems.
s/drm_gem_object_reference/i915_gem_object_get/
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1469005202-9659-5-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469017917-15134-4-git-send-email-chris@chris-wilson.co.uk
|
|
Currently execlists is exempt from emitting a request to switch each
ring away from the current context over to the dev_priv->kernel_context
(for whatever reason, just under execlists the GGTT is unlikely to be as
fragmented, however the switch may help in some extreme cases). Extract
the switcher and enable it for execlsts as well, as we need to do so in
a later patch to force the context switch before suspend. (And since for
that switch we explicitly require the disposable kernel context, rename
the extracted function.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1468590980-6186-1-git-send-email-chris@chris-wilson.co.uk
|
|
The contexts only pin space within the global GTT. Therefore forcing the
switch to the perma-pinned kernel context only has an effect when trying
to evict from and find room within the global GTT. We can then restrict
the switch to only when operating on the default context. This is mostly
a no-op as full-ppgtt only exists with execlists at present which skips
the context switch anyway.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466776558-21516-7-git-send-email-chris@chris-wilson.co.uk
|
|
We only need to force a switch to the kernel context placeholder during
eviction. All other uses of i915_gpu_idle() just want to wait until
existing work on the GPU is idle. Rename i915_gpu_idle() to
i915_gem_wait_for_idle() to avoid any implications about "parking" the
context first.
v2: Tweak an error message if the wait fails for the ilk vtd w/a
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466776558-21516-6-git-send-email-chris@chris-wilson.co.uk
|
|
text data bss dec hex filename
6309351 3578714 696320 10584385 a18141 vmlinux
6308391 3578714 696320 10583425 a17d81 vmlinux
Almost 1KiB of code reduction.
v2: More s/INTEL_INFO()->gen/INTEL_GEN()/ and IS_GENx() conversions
text data bss dec hex filename
6304579 3578778 696320 10579677 a16edd vmlinux
6303427 3578778 696320 10578525 a16a5d vmlinux
Now over 1KiB!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462545621-30125-3-git-send-email-chris@chris-wilson.co.uk
|
|
Elsewhere we have adopted the convention of using '_link' to denote
elements in the list (and '_list' for the actual list_head itself), and
that the name should indicate which list the link belongs to (and
preferrably not just where the link is being stored).
s/vma_link/obj_link/ (we iterate over obj->vma_list)
s/mm_list/vm_link/ (we iterate over vm->[in]active_list)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
Userspace can pass in an offset that it presumes the object is located
at. The kernel will then do its utmost to fit the object into that
location. The assumption is that userspace is handling its own object
locations (for example along with full-ppgtt) and that the kernel will
rarely have to make space for the user's requests.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
v2: Fixed incorrect eviction found by Michal Winiarski - fix suggested by Chris
Wilson. Fixed incorrect error paths causing crash found by Michal Winiarski.
(Not published externally)
v3: Rebased because of trivial conflict in object_bind_to_vm. Fixed eviction
to allow eviction of soft-pinned objects when another soft-pinned object used
by a subsequent execbuffer overlaps reported by Michal Winiarski.
(Not published externally)
v4: Moved soft-pinned objects to the front of ordered_vmas so that they are
pinned first after an address conflict happens to avoid repeated conflicts in
rare cases (Suggested by Chris Wilson). Expanded comment on
drm_i915_gem_exec_object2.offset to cover this new API.
v5: Added I915_PARAM_HAS_EXEC_SOFTPIN parameter for detecting this capability
(Kristian). Added check for multiple pinnings on eviction (Akash). Made sure
buffers are not considered misplaced without the user specifying
EXEC_OBJECT_SUPPORTS_48B_ADDRESS. User must assume responsibility for any
addressing workarounds. Updated object2.offset field comment again to clarify
NO_RELOC case (Chris). checkpatch cleanup.
v6: Trivial rebase on latest drm-intel-nightly
v7: Catch attempts to pin above the max virtual address size and return
EINVAL (Tvrtko). Decouple EXEC_OBJECT_SUPPORTS_48B_ADDRESS and
EXEC_OBJECT_PINNED flags, user must pass both flags in any attempt to pin
something at an offset above 4GB (Chris, Daniel Vetter).
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Akash Goel <akash.goel@intel.com>
Cc: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Zou Nanhai <nanhai.zou@intel.com>
Cc: Kristian Høgsberg <hoegsberg@gmail.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Acked-by: PDT
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449575707-20933-1-git-send-email-thomas.daniel@intel.com
|
|
With UMS gone, we no longer use it during suspend. And with the last
user removed from the shrinker, we can remove the dead code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
And remove one bogus * from i915_gem_gtt.c since that's not a
kerneldoc there.
v2: Review from Chris:
- Clarify memory space to better distinguish from address space.
- Add note that shrink doesn't guarantee the freed memory and that
users must fall back to shrink_all.
- Explain how pinning ties in with eviction/shrinker.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
v2: Use WARN_ONs (Daniel)
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
I've written these long before we've had a reasonable docbook
structure, and naturally they've gone stale. Fix this up asap.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
Also here, i915_gem_evict_vm causes an unbind, which can end up dropping
the last ref to the ppgtt.
Triggered by igt gem_evict_everything test.
Testcase: igt/gem_evict_everything
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Chris Wilson <chris@cris-wilsonc.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This is pure evil. Userspace, I'm looking at you SNA, repacks batch
buffers on the fly after generation as they are being passed to the
kernel for execution. These batches also contain self-referenced
relocations as a single buffer encompasses the state commands, kernels,
vertices and sampler. During generation the buffers are placed at known
offsets within the full batch, and then the relocation deltas (as passed
to the kernel) are tweaked as the batch is repacked into a smaller buffer.
This means that userspace is passing negative relocations deltas, which
subsequently wrap to large values if the batch is at a low address. The
GPU hangs when it then tries to use the large value as a base for its
address offsets, rather than wrapping back to the real value (as one
would hope). As the GPU uses positive offsets from the base, we can
treat the relocation address as the minimum address read by the GPU.
For the upper bound, we trust that userspace will not read beyond the
end of the buffer.
So, how do we fix negative relocations from wrapping? We can either
check that every relocation looks valid when we write it, and then
position each object such that we prevent the offset wraparound, or we
just special-case the self-referential behaviour of SNA and force all
batches to be above 256k. Daniel prefers the latter approach.
This fixes a GPU hang when it tries to use an address (relocation +
offset) greater than the GTT size. The issue would occur quite easily
with full-ppgtt as each fd gets its own VM space, so low offsets would
often be handed out. However, with the rearrangement of the low GTT due
to capturing the BIOS framebuffer, it is already affecting kernels 3.15
onwards. I think only IVB+ is susceptible to this bug, but the workaround
should only kick in rarely, so it seems sensible to always apply it.
v3: Use a bias for batch buffers to prevent small negative delta relocations
from wrapping.
v4 from Daniel:
- s/BIAS/BATCH_OFFSET_BIAS/
- Extract eb_vma_misplaced/i915_vma_misplaced since the conditions
were growing rather cumbersome.
- Add a comment to eb_get_batch explaining why we do this.
- Apply the batch offset bias everywhere but mention that we've only
observed it on gen7 gpus.
- Drop PIN_OFFSET_FIX for now, that slipped in from a feature patch.
v5: Add static to eb_get_batch, spotted by 0-day tester.
Testcase: igt/gem_bad_reloc
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78533
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Remove the rest of the references to drm_i915_private_t. No functional
changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Drop hunk in i915_cmd_parser.c]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Anything more than just one bool parameter is just a pain to read,
symbolic constants are much better.
Split out from Chris' vma-binding rework patch.
v2: Undo the behaviour change in object_pin that Chris spotted.
v3: Split out misplaced hunk to handle set_cache_level errors,
spotted by Jani.
v4: Keep the current over-zealous binding logic in the execbuffer code
working with a quick hack while the overall binding code gets shuffled
around.
v5: Reorder the PIN_ flags for more natural patch splitup.
v6: Pull out the PIN_GLOBAL split-up again.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Request by Ben Widawsky in his review of a patch touching this code.
v2: Clarify the disdinction between evicting vmas (to free up virtual
address space) and evicting objects (to free up actual system memory).
Suggested by Ben.
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Acked-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
During eviction, we are only considering how to free up space within the
current address space and not concerned with freeing up physical memory.
As such we need only skip nodes that pinned in the current VM and not
globally.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Because whatever.*
* This should contain a fairly long list of issues and still
unresolved resgressions, but I didn't really get a vote.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Since an old pageflip will keep its scanout buffer object pinned until
it has executed its unpin task on the common workqueue, we can clog up
our GGTT with stale pinned objects. As we cannot flush those workqueues
without dropping our locks, we have to resort to falling back to
userspace and telling them to repeat the operation in order to have a
chance to run our workqueues and free up the required memory. If we
fail, then we are forced to report ENOSPC back to userspace causing the
operation to fail and best-case scenario is that it introduces temporary
corruption.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jon Bloomfield <jon.bloomfield@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
I need the tricky do_switch fix before I can merge the final piece of
the ppgtt enabling puzzle. Otherwise the conflict will be a real pain
to resolve since the do_switch hunk from -fixes must be placed at the
exact right place within a hunk in the next patch.
Conflicts:
drivers/gpu/drm/i915/i915_gem_context.c
drivers/gpu/drm/i915/i915_gem_execbuffer.c
drivers/gpu/drm/i915/intel_display.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
With the advent of hw context support, we gained some objects that are
pinned for the duration of their request. That is we can make aperture
space available by idling the GPU and in the process performing a
context switch back to the always-pinned default context. As such, we
should not conclude that there is no space in the aperture for the
current object until we have unpinned any such context objects.
Note that we also have the problem of outstanding pageflips preventing
eviction of their framebuffer objects to resolve.
Testcase: igt/gem_ctx_exec/eviction
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=72507
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: lu hua <huax.lu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Tracing vm eviction is really the event we care about. For the cases we
evict everything, we still will get the trace.
v2: Add the drm device to the trace since we might not be the only
device in the system. (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
When reserving objects during execbuf, it is possible to come across an
object which will not fit given the current fragmentation of the address
space. We do not have any defragment in drm_mm, so the strategy is to
instead evict everything, and reallocate objects.
With the upcoming addition of multiple VMs, there is no point to evict
everything since doing so is overkill for the specific case mentioned
above.
Recommended-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: One additional s/evict_everything/evict_vm/ to update a
comment in the code.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
As we'll see in the next patch, being able to evict for just 1 VM is
handy.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The important bugfix here is that we must not unlink the vma when
we keep it around as a placeholder for the execbuf code. Since then we
won't find it again when execbuf gets interrupt and restarted and
create a 2nd vma. And since the code as-is isn't fit yet to deal with
more than one vma, hilarity ensues.
Specifically the dma map/unmap of the sg table isn't adjusted for
multiple vmas yet and will blow up like this:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: [<ffffffffa008fb37>] i915_gem_gtt_finish_object+0x73/0xc8 [i915]
PGD 56bb5067 PUD ad3dd067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in: tcp_lp ppdev parport_pc lp parport ipv6 dm_mod dcdbas snd_hda_codec_hdmi pcspkr snd_hda_codec_realtek serio_raw i2c_i801 iTCO_wdt iTCO_vendor_support snd_hda_intel snd_hda_codec lpc_ich snd_hwdep mfd_core snd_pcm snd_page_alloc snd_timer snd soundcore acpi_cpufreq i915 video button drm_kms_helper drm mperf freq_table
CPU: 1 PID: 16650 Comm: fbo-maxsize Not tainted 3.11.0-rc4_nightlytop_d93f59_debug_20130814_+ #6957
Hardware name: Dell Inc. OptiPlex 9010/03JR84, BIOS A01 05/04/2012
task: ffff8800563b3f00 ti: ffff88004bdf4000 task.ti: ffff88004bdf4000
RIP: 0010:[<ffffffffa008fb37>] [<ffffffffa008fb37>] i915_gem_gtt_finish_object+0x73/0xc8 [i915]
RSP: 0018:ffff88004bdf5958 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff8801135e0000 RCX: ffff8800ad3bf8e0
RDX: ffff8800ad3bf8e0 RSI: 0000000000000000 RDI: ffff8801007ee780
RBP: ffff88004bdf5978 R08: ffff8800ad3bf8e0 R09: 0000000000000000
R10: ffffffff86ca1810 R11: ffff880036a17101 R12: ffff8801007ee780
R13: 0000000000018001 R14: ffff880118c4e000 R15: ffff8801007ee780
FS: 00007f401a0ce740(0000) GS:ffff88011e280000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 000000005635c000 CR4: 00000000001407e0
Stack:
ffff8801007ee780 ffff88005c253180 0000000000018000 ffff8801135e0000
ffff88004bdf59a8 ffffffffa0088e55 0000000000000011 ffff8801007eec00
0000000000018000 ffff880036a17101 ffff88004bdf5a08 ffffffffa0089026
Call Trace:
[<ffffffffa0088e55>] i915_vma_unbind+0xdf/0x1ab [i915]
[<ffffffffa0089026>] __i915_gem_shrink+0x105/0x177 [i915]
[<ffffffffa0089452>] i915_gem_object_get_pages_gtt+0x108/0x309 [i915]
[<ffffffffa0085ba9>] i915_gem_object_get_pages+0x61/0x90 [i915]
[<ffffffffa008f22b>] ? gen6_ppgtt_insert_entries+0x103/0x125 [i915]
[<ffffffffa008a113>] i915_gem_object_pin+0x1fa/0x5df [i915]
[<ffffffffa008cdfe>] i915_gem_execbuffer_reserve_object.isra.6+0x8d/0x1bc [i915]
[<ffffffffa008d156>] i915_gem_execbuffer_reserve+0x229/0x367 [i915]
[<ffffffffa008dbf6>] i915_gem_do_execbuffer.isra.12+0x4dc/0xf3a [i915]
[<ffffffff810fc823>] ? might_fault+0x40/0x90
[<ffffffffa008eb89>] i915_gem_execbuffer2+0x187/0x222 [i915]
[<ffffffffa000971c>] drm_ioctl+0x308/0x442 [drm]
[<ffffffffa008ea02>] ? i915_gem_execbuffer+0x3ae/0x3ae [i915]
[<ffffffff817db156>] ? __do_page_fault+0x3dd/0x481
[<ffffffff8112fdba>] vfs_ioctl+0x26/0x39
[<ffffffff811306a2>] do_vfs_ioctl+0x40e/0x451
[<ffffffff817deda7>] ? sysret_check+0x1b/0x56
[<ffffffff8113073c>] SyS_ioctl+0x57/0x87
[<ffffffff8135bbfe>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[<ffffffff817ded82>] system_call_fastpath+0x16/0x1b
Code: 48 c7 c6 84 30 0e a0 31 c0 e8 d0 e9 f7 ff bf c6 a7 00 00 e8 07 af 2c e1 41 f6 84 24 03 01 00 00 10 75 44 49 8b 84 24 08 01 00 00 <8b> 50 08 48 8b 30 49 8b 86 b0 04 00 00 48 89 c7 48 81 c7 98 00
RIP [<ffffffffa008fb37>] i915_gem_gtt_finish_object+0x73/0xc8 [i915]
RSP <ffff88004bdf5958>
CR2: 0000000000000008
As a consequence we need to change the "only one vma for now" check in
vma_unbind - since vma_destroy isn't always called the obj->vma_list
might not be empty. Instead check that the vma list is singular at the
beginning of vma_unbind. This is also more symmetric with bind_to_vm.
This fixes the igt/gem_evict_everything|alignment testcases.
v2:
- Add a paranoid WARN to mark_free in the eviction code to make sure
we never try to evict a vma used by the execbuf code right now.
- Move the check for a temporary execbuf vma into vma_destroy -
otherwise the failure path cleanup in bind_to_vm will blow up.
Our first attempting at fixing this was
commit 1be81a2f2cfd8789a627401d470423358fba2d76
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Aug 20 12:56:40 2013 +0100
drm/i915: Don't destroy the vma placeholder during execbuffer reservation
Squash with this when merging!
v3: Improvements suggested in Chris' review:
- Move the WARN_ON in vma_destroy that checks for vmas with an drm_mm
allocation before the early return.
- Bail out if we hit the WARN in mark_free to hopefully make the
kernel survive for long enough to capture it.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <ben@bwidawsk.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68298
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68171
Tested-by: lu hua <huax.lu@intel.com> (v2)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The vma will [possibly] be destroyed during unbind in eviction.
Immediately after this, we try to delete the list entry.
Chris and Ville did the debug on this before I woke up, I just get to
take credit for the fix :p
For future reference the Oops that Mika reported:
[ 403.472448] BUG: unable to handle kernel paging request at 6b6b6b6b
[ 403.472473] IP: [<c12c1500>] __list_del_entry+0x20/0xe0
[ 403.472514] *pdpt = 000000002e89c001 *pde = 0000000000000000
[ 403.472556] Oops: 0000 [#1] SMP
[ 403.472582] Modules linked in: mxm_wmi snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi snd_rawmidi psmouse snd_seq_midi_event snd_seq serio_raw snd_timer snd_seq_device snd soundcore snd_page_alloc wmi bnep rfcomm bluetooth mac_hid parport_pc ppdev lp parport usbhid dm_crypt firewire_ohci firewire_core crc_itu_t i915 drm_kms_helper e1000e ptp drm i2c_algo_bit pps_core xhci_hcd video
[ 403.472895] CPU: 2 PID: 1940 Comm: Xorg Not tainted 3.11.0-rc2+ #827
[ 403.472938] Hardware name: /DZ77BH-55K, BIOS BHZ7710H.86A.0070.2012.0416.2117 04/16/2012
[ 403.473002] task: ec866c00 ti: ee6a2000 task.ti: ee6a2000
[ 403.473039] EIP: 0060:[<c12c1500>] EFLAGS: 00013202 CPU: 2
[ 403.473078] EIP is at __list_del_entry+0x20/0xe0
[ 403.473109] EAX: f016d9bc EBX: f016d9bc ECX: 6b6b6b6b EDX: 6b6b6b6b
[ 403.473151] ESI: 00000000 EDI: ee6a3c90 EBP: ee6a3c60 ESP: ee6a3c48
[ 403.473193] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 403.473230] CR0: 80050033 CR2: 6b6b6b6b CR3: 2ec43000 CR4: 001407f0
[ 403.473271] Stack:
[ 403.473285] f63b2ff0 f61f98c0 f61f8000 f016d9bc 00000000 f016d9bc ee6a3cac f8519a4a
[ 403.473347] 00000000 00000000 10000000 f61f8000 0100a000 10000000 00000001 008ca000
[ 403.473410] f64ee840 f61f98c0 f016d9bc f016dcec ee6a3c98 ee6a3c98 f61f98c0 dcc58f00
[ 403.473472] Call Trace:
[ 403.473509] [<f8519a4a>] i915_gem_evict_something+0x17a/0x2d0 [i915]
[ 403.473567] [<f8516ed1>] i915_gem_object_pin+0x271/0x660 [i915]
[ 403.473622] [<f851c740>] ? i915_ggtt_clear_range+0x20/0x20 [i915]
[ 403.473676] [<f8517afa>] i915_gem_object_pin_to_display_plane+0xda/0x190 [i915]
[ 403.473742] [<f852d9fa>] intel_pin_and_fence_fb_obj+0xba/0x140 [i915]
[ 403.473800] [<f852db40>] intel_gen7_queue_flip+0x30/0x1c0 [i915]
[ 403.473856] [<f85337b0>] intel_crtc_page_flip+0x1a0/0x320 [i915]
[ 403.473911] [<f847b549>] ? drm_framebuffer_reference+0x39/0x80 [drm]
[ 403.473965] [<f847f9fb>] drm_mode_page_flip_ioctl+0x28b/0x320 [drm]
[ 403.474018] [<f846fec8>] drm_ioctl+0x4b8/0x560 [drm]
[ 403.474064] [<f847f770>] ? drm_mode_gamma_get_ioctl+0xd0/0xd0 [drm]
[ 403.474113] [<c1140f8a>] ? do_sync_read+0x6a/0xa0
[ 403.474154] [<f846fa10>] ? drm_copy_field+0x80/0x80 [drm]
[ 403.474193] [<c115134c>] do_vfs_ioctl+0x7c/0x5b0
[ 403.474228] [<c1141d2f>] ? vfs_read+0xef/0x160
[ 403.474263] [<c108dcbb>] ? ktime_get_ts+0x4b/0x120
[ 403.474298] [<c1151917>] SyS_ioctl+0x97/0xa0
[ 403.474330] [<c1590bc1>] sysenter_do_call+0x12/0x22
[ 403.474364] Code: 55 f4 8b 45 f8 e9 75 ff ff ff 90 55 89 e5 53 83 ec 14 8b 08 8b 50 04 81 f9 00 01 10 00 74 24 81 fa 00 02 20 00 0f 84 8e 00 00 00 <8b> 1a 39 d8 75 62 8b 59 04 39 d8 75 35 89 51 04 89 0a 83 c4 14
[ 403.474566] EIP: [<c12c1500>] __list_del_entry+0x20/0xe0 SS:ESP 0068:ee6a3c48
[ 403.476513] CR2: 000000006b6b6b6b
v2: Missed the drm_object_unreference use after free (Ville)
Daniel Vetter <daniel@ffwll.ch> writes:
Reported-by: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add the Oops from Mika to the commit message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The execbuf wants to do relocations usings vmas, so we need a
vma->exec_list. The eviction code also uses the old obj execbuf list
for it's own book-keeping, but would really prefer to deal in vmas
only. So switch it over to the new list.
Again this is just a prep patch for the big execbuf vma conversion.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Split out from Ben's big execbuf vma patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
formerly: "drm/i915: Create VMAs (part 5) - move mm_list"
The mm_list is used for the active/inactive LRUs. Since those LRUs are
per address space, the link should be per VMx .
Because we'll only ever have 1 VMA before this point, it's not incorrect
to defer this change until this point in the patch series, and doing it
here makes the change much easier to understand.
Shamelessly manipulated out of Daniel:
"active/inactive stuff is used by eviction when we run out of address
space, so needs to be per-vma and per-address space. Bound/unbound otoh
is used by the shrinker which only cares about the amount of memory used
and not one bit about in which address space this memory is all used in.
Of course to actual kick out an object we need to unbind it from every
address space, but for that we have the per-object list of vmas."
v2: only bump GGTT LRU in i915_gem_object_set_to_gtt_domain (Chris)
v3: Moved earlier in the series
v4: Add dropped message from v3
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Frob patch to apply and use vma->node.size directly as
discused with Ben. Also drop a needles BUG_ON before move_to_inactive,
the function itself has the same check.]
[danvet 2nd: Rebase on top of the lost "drm/i915: Cleanup more of VMA
in destroy", specifically unlink the vma from the mm_list in
vma_unbind (to keep it symmetric with bind_to_vm) instead of
vma_destroy.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Eviction code, like the rest of the converted code needs to be aware of
the address space for which it is evicting (or the everything case, all
addresses). With the updated bind/unbind interfaces of the last patch,
we can now safely move the eviction code over.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
As alluded to in several patches, and it will be reiterated later... A
VMA is an abstraction for a GEM BO bound into an address space.
Therefore it stands to reason, that the existing bind, and unbind are
the ones which will be the most impacted. This patch implements this,
and updates all callers which weren't already updated in the series
(because it was too messy).
This patch represents the bulk of an earlier, larger patch. I've pulled
out a bunch of things by the request of Daniel. The history is preserved
for posterity with the email convention of ">" One big change from the
original patch aside from a bunch of cropping is I've created an
i915_vma_unbind() function. That is because we always have the VMA
anyway, and doing an extra lookup is useful. There is a caveat, we
retain an i915_gem_object_ggtt_unbind, for the global cases which might
not talk in VMAs.
> drm/i915: plumb VM into object operations
>
> This patch was formerly known as:
> "drm/i915: Create VMAs (part 3) - plumbing"
>
> This patch adds a VM argument, bind/unbind, and the object
> offset/size/color getters/setters. It preserves the old ggtt helper
> functions because things still need, and will continue to need them.
>
> Some code will still need to be ported over after this.
>
> v2: Fix purge to pick an object and unbind all vmas
> This was doable because of the global bound list change.
>
> v3: With the commit to actually pin/unpin pages in place, there is no
> longer a need to check if unbind succeeded before calling put_pages().
> Make put_pages only BUG() after checking pin count.
>
> v4: Rebased on top of the new hangcheck work by Mika
> plumbed eb_destroy also
> Many checkpatch related fixes
>
> v5: Very large rebase
>
> v6:
> Change BUG_ON to WARN_ON (Daniel)
> Rename vm to ggtt in preallocate stolen, since it is always ggtt when
> dealing with stolen memory. (Daniel)
> list_for_each will short-circuit already (Daniel)
> remove superflous space (Daniel)
> Use per object list of vmas (Daniel)
> Make obj_bound_any() use obj_bound for each vm (Ben)
> s/bind_to_gtt/bind_to_vm/ (Ben)
>
> Fixed up the inactive shrinker. As Daniel noticed the code could
> potentially count the same object multiple times. While it's not
> possible in the current case, since 1 object can only ever be bound into
> 1 address space thus far - we may as well try to get something more
> future proof in place now. With a prep patch before this to switch over
> to using the bound list + inactive check, we're now able to carry that
> forward for every address space an object is bound into.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Rebase on top of the loss of "drm/i915: Cleanup more of VMA
in destroy".]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Earlier in the conversion sequence we attempted to quickly wedge in the
transitional interface as static inlines.
Now that we're sure these interfaces are sane, for easier debug and to
decrease code size (since many of these functions may be called quite a
bit), make them real functions
While at it, kill off the set_color interface. We'll always have the
VMA, or easily get to it.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Formerly: "drm/i915: Create VMAs (part 1)"
In a previous patch, the notion of a VM was introduced. A VMA describes
an area of part of the VM address space. A VMA is similar to the concept
in the linux mm. However, instead of representing regular memory, a VMA
is backed by a GEM BO. There may be many VMAs for a given object, one
for each VM the object is to be used in. This may occur through flink,
dma-buf, or a number of other transient states.
Currently the code depends on only 1 VMA per object, for the global GTT
(and aliasing PPGTT). The following patches will address this and make
the rest of the infrastructure more suited
v2: s/i915_obj/i915_gem_obj (Chris)
v3: Only move an object to the now global unbound list if there are no
more VMAs for the object which are bound into a VM (ie. the list is
empty).
v4: killed obj->gtt_space
some reworks due to rebase
v5: Free vma on error path (Imre)
v6: Another missed vma free in i915_gem_object_bind_to_gtt error path
(Imre)
Fixed vma freeing in stolen preallocation (Imre)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Squash in fixup from Ben to not deref a non-existing vma in
set_cache_level, reported by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
