| Age | Commit message (Collapse) | Author |
|---|
|
drm_kms_helper_poll_enable_locked() should check if we have delayed event
pending and if we have, schedule the work to run without delay.
Currently the output_poll_work is only scheduled if any of the connectors
have DRM_CONNECTOR_POLL_CONNECT or DRM_CONNECTOR_POLL_DISCONNECT with
DRM_OUTPUT_POLL_PERIOD delay. It does not matter if we have delayed event
already registered to be handled. The detection will be delayd by
DRM_OUTPUT_POLL_PERIOD in any case.
Furthermore if none of the connectors are marked as POLL_CONNECT or
POLL_DISCONNECT because all connectors are either POLL_HPD or they are
always connected: the output_poll_work will not run at all even if we
have delayed event marked.
When none of the connectors require polling, their initial status change
from unknown to connected/disconnected is not going to be handled until
the first kms application starts or if we have fb console enabled.
Note that in general the output poll work should be enabled already
when this happens, but at driver load usually the first probe happens
before the output polling is enabled. This patch fixes this case.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[danvet: Note when exactly this is an issue, since the probe code
schedules the poll work itself already.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160831110905.31289-1-peter.ujfalusi@ti.com
|
|
The intention of using video=<connector>:<mode> is primarily to select
the user's preferred resolution at startup. Currently we always create a
new mode irrespective of whether the monitor has a native mode at the
desired resolution. This has the issue that we may then select the fake
mode rather the native mode during fb_helper->inital_config() and so
if the fake mode is invalid we then end up with a loss of signal. Oops.
This invalid fake mode would also be exported to userspace, who
potentially may make the same mistake.
To avoid this issue, we filter out the added command line mode if we
detect the desired resolution (and clock if specified) amongst the
probed modes. This fixes the immediate problem of adding a duplicate
mode, but perhaps more generically we should avoid adding a GTF mode if
the monitor has an EDID that is not GTF-compatible, or similarly for
CVT.
Was meant to fix a regression from
commit eaf99c749d43ae74ac7ffece5512f3c73f01dfd2
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Aug 6 10:08:32 2014 +0200
drm: Perform cmdline mode parsing during connector initialisation
but Radek explained that the original bug is no longer reproducible on
latest kernels.
v2: Explicitly delete our earlier cmdline mode
v3: Mode pruning should now be sufficient to delete stale cmdline modes
v4: Compute the vrefresh for the probed mode
Reported-by: Radek Dostál <rd@radekdostal.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Radek Dostál <rd@radekdostal.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Cc: Julia Lemire <jlemire@matrox.com>
Cc: Dave Airlie <airlied@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Drop cc: stable since no longer a pressing bugfix, just
nice-to-have.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1464774651-20376-1-git-send-email-chris@chris-wilson.co.uk
|
|
Push the ifdef to the drm_edid.h and create a stub, for the
DRM_LOAD_EDID_FIRMWARE=n case. This removes some clutter in
the code, making it more readable.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1461087638-16959-1-git-send-email-ezequiel@vanguardiasur.com.ar
|
|
Describe the procedure that drm_helper_probe_single_connector_modes()
uses to do it's work in the kernel-doc comment.
Caveat: Looks like crap and trying to reverse engineer the documentation
tools is not something I want to do.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449782037-19722-3-git-send-email-ville.syrjala@linux.intel.com
|
|
IMO the override_edid should override any default EDID for the
connector, whether that came in via the connector helper ->get_modes()
vfunc or via the firmware EDID mechanism.
Cc: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449782037-19722-2-git-send-email-ville.syrjala@linux.intel.com
|
|
Now that the mode type bit merge logic is fixed to only merge
between new probed modes, hopefully we can eliminat the special
case for qxl and virtio. That is make the merge the mode type
bits from all matching new probed modes, just like every other
driver.
qxl and virtio got excluded from the merging in
commit 3fbd6439e463 ("drm: copy mode type in drm_mode_connector_list_update()")
commit abce1ec9b08a ("Revert "drm: copy mode type in drm_mode_connector_list_update()"")
commit b87577b7c768 ("drm: try harder to avoid regression when merging mode bits")
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Adam Jackson <ajax@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Resolve conflicts with doc updates.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
MODE_UNVERIFIED actually means that the mode came from a previous probe,
and if the new probe doesn't produce a matching mode it will get pruned
from the list. Rename the flag to MODE_STALE to better convey the
meaning.
v2: Rebased due to conflicts with Daniel's doc stuff
Cc: Adam Jackson <ajax@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449779948-10906-1-git-send-email-ville.syrjala@linux.intel.com
|
|
The way the mode probing works is this:
1. All modes currently on the mode list are marked as UNVERIFIED
2. New modes are on the probed_modes list (they start with
status OK)
3. Modes are moved from the probed_modes list to the actual
mode list. If a mode already on the mode list is deemed
to match one of the probed modes, the duplicate is dropped
and the mode status updated to OK. After this the
probed_modes list will be empty.
4. All modes on the mode list are verified to not violate any
constraints. Any that do are marked as such.
5. Any mode left with a non-OK status is pruned from the list,
with an appropriate debug message.
What all this means is that any mode on the original list that
didn't have a duplicate on the probed_modes list, should be left
with status UNVERFIED (or previously could have been left with
some other status, but never OK).
I broke that in
commit 05acaec334fc ("drm: Reorganize probed mode validation")
by always assigning something to the mode->status during the validation
step. So any mode from the old list that still passed the validation
would be left on the list with status OK in the end.
Fix this by not doing the basic mode validation unless the mode
already has status OK (meaning it came from the probed_modes list,
or at least a duplicate of it was on that list). This way we will
correctly prune away any mode from the old mode list that didn't
appear on the probed_modes list.
Cc: stable@vger.kernel.org
Cc: Adam Jackson <ajax@redhat.com>
Fixes: 05acaec334fc ("drm: Reorganize probed mode validation")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449177255-9515-2-git-send-email-ville.syrjala@linux.intel.com
Testcase: igt/kms_force_connector_basic/prune-stale-modes
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93332
[danvet: Also applying to drm-misc to avoid too much conflict hell -
there's a big pile of patches from Ville on top of this one.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Duplication is bad, luckily both help texts highlighted different
issues so the kerneldoc gained quite a bit!
While at it also sprinkle more references to the vtable structs around
and make it clear that legacy CRTC helpers are deprecated and which
functions to use instead.
v2: Spelling fixes and polish (Thierry).
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-6-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
|
|
Currently we have 4 helper libraries (probe, crtc, plane & atomic)
that all use the same helper vtables. And that's by necessity since we
don't want to litter the core structs with one ops pointer per helper
library. Also often the reuse the same hooks (like atomic does, to
facilite conversion from existing drivers using crtc and plane
helpers).
Given all that it doesn't make sense to put the docs for these next to
specific helpers. Instead extract them into a new header file and
section in the docbook, and add references to them everywhere.
Unfortunately kernel-doc complains when an include directive doesn't
find anything (and it does by dumping crap into the output file). We
have to remove the now empty includes to avoid that, instead of leaving
them in for future proofing.
v2: More OCD in ordering functions.
v3: Spelling plus collate copyright headers properly.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-4-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
|
|
We've had human readable connector status change debug logging since
commit ed7951dc13aad4a14695ec8122e9f0e2ef25d39e
Author: Lespiau, Damien <damien.lespiau@intel.com>
Date: Fri May 10 12:36:42 2013 +0000
drm: Make the HPD status updates debug logs more readable
but
commit 162b6a57ac50eec236530a16c071ffa50e87362a
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Jan 21 08:45:21 2015 +0100
drm/probe-helper: don't lose hotplug event
added a new one with just the numbers. Fix it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449144003-2877-1-git-send-email-jani.nikula@intel.com
|
|
To avoid even more code duplication punt this all to the probe worker,
which needs some slight adjustment to also generate a uevent when the
status has changed to due connector->force.
v2: Instead of running the output_poll_work (which is kinda the wrong
thing and a layering violation since it's an internal of the probe
helpers), or calling ->detect (which is again a layering violation
since it's used only by probe helpers) just call the official
->fill_modes function, like a GET_CONNECTOR ioctl call.
v3: Restore the accidentally removed forced-probe for echo "detect" >
force.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447951610-12622-22-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
drm_kms_helper_poll_enable() was converted to lock the mode_config
mutex in commit 8c4ccc4ab6f64e859d4ff8d7c02c2ed2e956e07f
("drm/probe-helper: Grab mode_config.mutex in poll_init/enable").
This disregarded the cases where this function is called from a context
where this mutex is already locked.
Add a non-locking version as well.
Changes since v1:
- use function name suffix '_locked' for the function that
is to be called from a locked context.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
So on first looks this seems superflous since drivers should ensure
correct ordering to not make this a problem. Otoh ordering constraints
between hdp, fbdev load and enabling polling are already tricky on
some hardware and it helps to be more robust.
But the real goal is to just shut up a locking WARN_ON I'd like to
add, which means init code gets some additional locks just for
uniformity.
v2: Also grab the lock for the public poll_enable, not just poll_init
which is used for resume, with the same justification.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
And roll them out across drm_* files. The point here isn't code
prettification (it helps with that too) but that some of these lists
aren't static any more. And having macros will gives us a convenient
place to put locking checks into.
I didn't add an iterator for props since that's only used by a
list_for_each_entry_safe in the driver teardown code.
Search&replace was done with the below cocci spatch. Note that there's
a bunch more places that didn't match and which would need some manual
changes, but I've intentially left these out for this mostly automated
patch.
iterator name drm_for_each_crtc;
struct drm_crtc *crtc;
struct drm_device *dev;
expression head;
@@
- list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) {
+ drm_for_each_crtc (crtc, dev) {
...
}
@@
iterator name drm_for_each_encoder;
struct drm_encoder *encoder;
struct drm_device *dev;
expression head;
@@
- list_for_each_entry(encoder, &dev->mode_config.encoder_list, head) {
+ drm_for_each_encoder (encoder, dev) {
...
}
@@
iterator name drm_for_each_fb;
struct drm_framebuffer *fb;
struct drm_device *dev;
expression head;
@@
- list_for_each_entry(fb, &dev->mode_config.fb_list, head) {
+ drm_for_each_fb (fb, dev) {
...
}
@@
iterator name drm_for_each_connector;
struct drm_connector *connector;
struct drm_device *dev;
expression head;
@@
- list_for_each_entry(connector, &dev->mode_config.connector_list, head) {
+ drm_for_each_connector (connector, dev) {
...
}
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
misc drm core patches.
* tag 'topic/drm-misc-2015-05-06' of git://anongit.freedesktop.org/drm-intel:
drm: simplify master cleanup
drm: simplify authentication management
drm: drop unused 'magicfree' list
drm: fix a memleak on mutex failure path
drm/atomic-helper: Really recover pre-atomic plane/cursor behavior
drm/qxl: Fix qxl_noop_get_vblank_counter()
drm: Zero out invalid vblank timestamp in drm_update_vblank_count. (v2)
drm: Prevent invalid use of vblank_disable_immediate. (v2)
drm/vblank: Fixup and document timestamp update/read barriers
DRM: Don't re-poll connector for disconnect
drm: Fix for DP CTS test 4.2.2.5 - I2C DEFER handling
drm: Fix the 'native defer' message in drm_dp_i2c_do_msg()
drm/atomic-helper: Don't call atomic_update_plane when it stays off
|
|
DRM probe should not repoll a connector if it is already
connected and the DRM_CONNECTOR_POLL_DISCONNECT flag is not set.
Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
One more drm-misch pull for 4.1 with mostly simple stuff and boring
refactoring. Even the cursor fix from Matt is just to make a really anal
igt happy.
* tag 'topic/drm-misc-2015-04-15' of git://anongit.freedesktop.org/drm-intel:
drm: fix trivial typo mistake
drm: Make integer overflow checking cover universal cursor updates (v2)
drm: make crtc/encoder/connector/plane helper_private a const pointer
drm/armada: constify struct drm_encoder_helper_funcs pointer
drm/radeon: constify more struct drm_*_helper funcs pointers
drm/edid: add #defines for ELD versions
drm/atomic: Add for_each_{connector,crtc,plane}_in_state helper macros
drm: Use kref_put_mutex in drm_gem_object_unreference_unlocked
drm/drm: constify all struct drm_*_helper funcs pointers
drm/qxl: constify all struct drm_*_helper funcs pointers
drm/nouveau: constify all struct drm_*_helper funcs pointers
drm/radeon: constify all struct drm_*_helper funcs pointers
drm/gma500: constify all struct drm_*_helper funcs pointers
drm/mgag200: constify all struct drm_*_helper funcs pointers
drm/exynos: constify all struct drm_*_helper funcs pointers
drm: Fix some typos
|
|
They are not to be modified.
Generated using the semantic patch:
@@
@@
(
const struct drm_crtc_helper_funcs *
|
- struct drm_crtc_helper_funcs *
+ const struct drm_crtc_helper_funcs *
)
@@
@@
(
const struct drm_encoder_helper_funcs *
|
- struct drm_encoder_helper_funcs *
+ const struct drm_encoder_helper_funcs *
)
@@
@@
(
const struct drm_connector_helper_funcs *
|
- struct drm_connector_helper_funcs *
+ const struct drm_connector_helper_funcs *
)
@@
@@
(
const struct drm_plane_helper_funcs *
|
- struct drm_plane_helper_funcs *
+ const struct drm_plane_helper_funcs *
)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
If the user supplies EDID through firmware or debugfs override, the
driver callbacks are bypassed and the connector ELD does not get
updated, and audio fails. Set ELD for firmware and debugfs EDIDs too.
There should be no harm in gratuitously doing this for non HDMI/DP
connectors, as it's still up to the driver to use the ELD, if any.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82349
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=80691
Reported-by: Emil <emilsvennesson@gmail.com>
Reported-by: Rob Engle <grenoble@gmail.com>
Tested-by: Jolan Luff <jolan@gormsby.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
On some chipset we try to avoid possibly invasive output detection
methods (like load detect which can cause flickering elsewhere) in the
output poll work. Drivers could hence return unknown when a previous
full ->detect call returned a different state.
This change will generate a hotplug event, forcing userspace to do a
full scan. This in turn updates the connector->status field so that we
will _again_ get a state change when the hotplug work re-runs in 10
seconds.
To avoid this ping-pong loop detect this situation and clamp the
connector state to the old value.
Patch is inspired by a patch from Knut Peterson. Knut's patch
completely ignored connector state changes if either the old or new
status was unknown, which seemed to be a bit too agressive to me.
v2: Rebased onto the drm_probe_helper.c extraction.
References: http://lists.freedesktop.org/archives/dri-devel/2012-August/025975.html
Cc: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
There's a race window (small for hpd, 10s large for polled outputs)
where userspace could sneak in with an unrelated connnector probe
ioctl call and eat the hotplug event (since neither the hpd nor the
poll code see a state change).
To avoid this, check whether the connector state changes in all other
->detect calls (in the current helper code that's only probe_single)
and if that's the case, fire off a hotplug event. Note that we can't
directly call the hotplug event handler, since that expects that no
locks are held (due to reentrancy with the fb code to update the kms
console).
Also, this requires that drivers using the probe_single helper
function set up the poll work. All current drivers do that already,
and with the reworked hpd handling there'll be no downside to
unconditionally setting up the poll work any more.
v2: Review from Rob Clark
- Don't bail out of the output poll work immediately if it's disabled
to make sure we deliver the delayed hoptplug events. Instead just
jump to the tail.
- Don't scheduel the work when it's not set up. Would be a driver bug
since using probe helpers for anything dynamic without them
initialized makes them all noops.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Tested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Make sure the timings of probed modes at least pass some very basic
sanity checks.
The checks include:
- clock,hdisplay,vdisplay are non zero
- sync pulse fits within the blanking period
- htotal,vtotal are big enough
I have not checked all the drivers to see if the modes the generate
might violate these constraints. I'm hoping not, because that would mean
either abandoning the idea of doing this from the core code, or fixing
the drivers.
I'm not entirely sure about limiting the sync pulse to the blanking
period. Intel hardware doesn't support such things, but some other
hardware might. However at least HDMI doesn't allow having sync pulse
edges within the active period, so I'm thinking the check is probably
OK to have in the common code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Make drm_mode_validate_size() and drm_mode_validate_flag() deal with a
single mode instead of having each iterate through the mode list.
The hope is that in the future we might be able to share various mode
validation functions between modeset and get_modes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
A connector may be forced on from the command line via video=
command line setting. The digital output of dual-mode connectors
can also be specifically selected and forced on; eg., 'video=DVI-I-2:D'.
However, in this case, the connector->status will be mistakenly set to
connector_status_disconnected, and the connector will not be mode set.
Fix the connector->status when connector->force is DRM_FORCE_ON_DIGITAL.
Note that this seems to have been broken ever since the introduction
of the connector forcing support in
commit d50ba256b5f1478e15accfcfda9b72fd7a661364
Author: Dave Airlie <airlied@linux.ie>
Date: Wed Sep 23 14:44:08 2009 +1000
drm/kms: start adding command line interface using fb.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
[danvet: Add note about that this never worked.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
i915.ko has a custom fbdev initialisation routine that aims to preserve
the current mode set by the BIOS, unless overruled by the user. The
user's wishes are determined by what, if any, mode is specified on the
command line (via the video= parameter). However, that command line mode
is first parsed by drm_fb_helper_initial_config() which is called after
i915.ko's custom initial_config() as a fallback method. So in order for
us to honour it, we need to move the cmdline parser earlier. If we
perform the connector cmdline parsing as soon as we initialise the
connector, that cmdline mode and forced status is then available even if
the fbdev helper is not compiled in or never called.
We also then expose the cmdline user mode in the connector mode lists.
v2: Rebase after connector->name upheaval.
v3: Adapt mga200 to look for the cmdline mode in the new place. Nicely
simplifies things while at that.
v4: Fix checkpatch.
v5: Select FB_CMDLINE to adapt to the changed fbdev patch.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73154
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v2)
Cc: dri-devel@lists.freedesktop.org
Cc: Julia Lemire <jlemire@matrox.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Add a file to debugfs for each connector to allow the EDID to be
overridden.
v2: Copy ubuf before accessing it and reject invalid length data. (David
Herrmann)
Ensure override_edid is reset when a new EDID value is written.
(David Herrmann)
Fix the debugfs file permissions. (David Herrmann)
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Generated using semantic patch:
@@
expression E;
@@
- drm_get_connector_name(E)
+ E->name
[airlied: regenerated]
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
Update pull request with drm core patches. Mostly some polish for the
primary plane stuff and a pile of patches all over from Thierry. Has
survived a few days in drm-intel-nightly without causing ill.
I've frobbed my scripts a bit to also tag my topic branches so that you
have something stable to pull - I've accidentally pushed a bunch more
patches onto this branch before you've taken the old pull request.
* tag 'topic/core-stuff-2014-05-05' of git://anongit.freedesktop.org/drm-intel:
drm: Make drm_crtc_helper_disable() return void
drm: Fix indentation of closing brace
drm/dp: Fix typo in comment
drm: Fixup flip-work kerneldoc
drm/fb: Fix typos
drm/edid: Cleanup kerneldoc
drm/edid: Drop revision argument for drm_mode_std()
drm: Try to acquire modeset lock on panic or sysrq
drm: remove unused argument from drm_open_helper
drm: Handle ->disable_plane failures correctly
drm: Simplify fb refcounting rules around ->update_plane
drm/crtc-helper: gc usless connector loop in disable_unused_functions
drm/plane_helper: don't disable plane in destroy function
drm/plane-helper: Fix primary plane scaling check
drm: make mode_valid callback optional
drm/edid: Fill PAR in AVI infoframe based on CEA mode list
|
|
For QXL hw we really want the bits to be replaced as we change
the preferred mode on the fly, and the same goes for virgl when
I get to it, however the original fix for this seems to have caused
a wierd regression on Intel G33 that in a stunning display of failure
at opposition to his normal self, Daniel failed to diagnose.
So we are left doing this, ugly ugly ugly ugly, Daniel you fixed
that G33 yet?, ugly, ugly.
Tested-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Many drm connectors do not need mode validation.
The patch makes this callback optional and removes dumb implementations.
v2: Rebase:
- imx move to a shared (but still dummy) ->mode_valid implementation.
- probe helpers have been extracted to drm_probe_helper.c
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This is leftover stuff from my previous doc round which I kinda wanted
to do but didn't yet due to rebase hell.
The modeset helpers and the probing helpers a independent and e.g.
i915 uses the probing stuff but has its own modeset infrastructure. It
hence makes to split this up. While at it add a DOC: comment for the
probing libraray.
It would be rather neat to pull some of the DocBook documenting these
two helpers into in-line DOC: comments. But unfortunately kerneldoc
doesn't support markdown or something similar to make nice-looking
documentation, so the current state is better.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
