| Age | Commit message (Collapse) | Author |
|---|
|
In gpio_get(), _get_gpio_datain() and _get_gpio_dataout() get rid of
un-necessary operation to compute gpio mask. The gpio offset passed
to gpio_get() is sufficient to do that.
Here is Russell's original comment:
Can someone explain to me this:
static int _get_gpio_datain(struct gpio_bank *bank, int gpio)
{
void __iomem *reg = bank->base + bank->regs->datain;
return (__raw_readl(reg) & GPIO_BIT(bank, gpio)) != 0;
}
static int gpio_get(struct gpio_chip *chip, unsigned offset)
{
struct gpio_bank *bank = container_of(chip, struct gpio_bank, chip);
void __iomem *reg = bank->base;
int gpio = chip->base + offset;
u32 mask = GPIO_BIT(bank, gpio);
if (gpio_is_input(bank, mask))
return _get_gpio_datain(bank, gpio);
else
return _get_gpio_dataout(bank, gpio);
}
Given that bank->width on OMAP is either 32 or 16, and GPIO numbers for
any GPIO chip are always aligned to 32 or 16, why does this code bother
adding the chips base gpio number and then modulo the width?
Surely this means if - for argument sake - you registered a GPIO chip
with 8 lines followed by one with 16 lines, GPIO0..7 would be chip 0
bit 0..7, GPIO8..15 would be chip 1 bit 8..15, GPIO16..23 would be
chip 1 bit 0..7.
However, if you registered a GPIO chip with 16 lines first, it would
mean GPIO0..15 would be chip 0 bit 0..15, and GPIO16..31 would be
chip 1 bit 0..15.
Surely this kind of behaviour is not intended?
Is there a reason why the bitmask can't just be (1 << offset) where
offset is passed into these functions as GPIO number - chip->base ?
Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
In _enable_gpio_irqbank() when bank->regs->set_irqenable is TRUE,
gpio_mask can be directly set by writing to set_irqenable register
without overwriting current value. In order to ensure the same is
stored in context.irqenable1, we must avoid overwriting it with
gpio_mask at the end of the function. Instead, update irqenable1
appropriately by OR'ing with gpio_mask.
For the case where bank->regs->set_irqenable is FALSE, irqenable1
can be directly overwritten with 'l' which holds correct computed
value.
if (bank->regs->set_irqenable) {
reg += bank->regs->set_irqenable;
l = gpio_mask;
} else {
reg += bank->regs->irqenable;
l = __raw_readl(reg);
if (bank->regs->irqenable_inv)
l &= ~gpio_mask;
else
l |= gpio_mask;
}
Make similar change for _disable_gpio_irqbank().
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
In omap_gpio_runtime_suspend/resume() the context save/restore should
be independent of bank->enabled_non_wakeup_gpios. This was preventing
context restore of GPIO lines which are not wakeup enabled.
Reported-by: Govindraj Raja <govindraj.raja@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
There are two functions, _set_gpio_dataout_reg() and _set_gpio_dataout_mask()
which writes to dataout register and the dataout context must be saved.
It is missing in the first function, _set_gpio_dataout_reg(). Fix this.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
This function should be capable of both enabling and disabling interrupts
based upon the *enable* parameter. Right now the function only enables
the interrupt and *enable* is not used at all. So add the interrupt
disable capability also using the parameter.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
The GPIO trigger parameter is of type unsigned.
enum {
IRQ_TYPE_NONE = 0x00000000,
IRQ_TYPE_EDGE_RISING = 0x00000001,
IRQ_TYPE_EDGE_FALLING = 0x00000002,
IRQ_TYPE_EDGE_BOTH = (IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING),
IRQ_TYPE_LEVEL_HIGH = 0x00000004,
IRQ_TYPE_LEVEL_LOW = 0x00000008,
IRQ_TYPE_LEVEL_MASK = (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH),
IRQ_TYPE_SENSE_MASK = 0x0000000f,
IRQ_TYPE_PROBE = 0x00000010,
...
};
Even though gpio_irq_type(struct irq_data *d, unsigned type) has the right type
of parameter, the subsequent called functions set_gpio_triggering() and
set_gpio_trigger() wrongly makes it signed integer. Fix this.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
There are two ways through which wakeup_en register can be programmed
using gpiolib APIs as shown below. It is seen that in the second case
in _set_gpio_wakeup(), even though bank->suspend_wakeup is updated
correctly, its value is not programmed in wakeup_en register. Fix this.
irq_set_type()->gpio_irq_type()->_set_gpio_triggering()->set_gpio_trigger()
irq_set_wake()->gpio_wake_enable()->_set_gpio_wakeup()
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
This function is called from non-__init context, just like
tegra_gpio_enable()/disable(). Remove the __init annotation to avoid
section mismatch warnings during compile.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Initial board support for the GE IMP3A, a 3U compactPCI card with a p2020
processor.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The GE GPIO driver provides basic support (set direction, read/write state)
for the GPIO provided on some GE single board computers. This patch moves
the driver from the 86xx specific platform directrory to the GPIO subsystem
so that it can be used on non-86xx boards.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/drivers
* 'next/soc-exynos5250-gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (201 commits)
gpio/samsung: use ioremap() for EXYNOS4 GPIOlib
gpio/samsung: add support GPIOlib for EXYNOS5250
ARM: EXYNOS: add support GPIO for EXYNOS5250
(update to v3.3-rc7)
Conflicts:
arch/arm/mach-pxa/pxa25x.c
arch/arm/mach-pxa/pxa27x.c
The dummy clock for the pxa rtc in those files keeps getting added and
removed in various trees. Apparently removing is the correct solution.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
into next/cleanup
* 'ep93xx-for-arm-soc' of git://github.com/RyanMallon/linux-2.6:
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
(update to v3.3-rc7)
Conflicts:
arch/arm/mach-s3c2440/common.h
|
|
This patch changes to use ioremap() for EXYNOS4210
so that we can drop the static mapping for EXYNOS
SoCs.
Note: Will be updated for all of Samsung GPIOlibs
to use ioremap() next time.
Signed-off-by: Sangsu Park <sangsu4u.park@samsung.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds gpio_chips for EXYNOS5250 and replaces
exynos4_xxx() with exynos_xxx() and variables to support
exynos4 and exynos5 together.
In addition, use ioreamp() for base address of gpios.
Signed-off-by: Sangsu Park <sangsu4u.park@samsung.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Move the pinmux setting of the EP93xx GPIOs to the core code. This
removes the need for the GPIO driver to have access to the system
controller registers.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Hartley Sweeten <hsweeten@visionengravers.com>
|
|
Unbanked GPIO IRQ handling code made a copy of just
the irq_chip structure for GPIO IRQ lines which caused
problems after the generic IRQ chip conversion because
there was no valid irq_chip_type structure with the
right "regs" populated. irq_gc_mask_set_bit() was
therefore accessing random addresses.
Fix it by making a copy of irq_chip_type structure
instead. This will ensure sane register offsets.
Cc: <stable@vger.kernel.org> # v3.0.x+
Reported-by: Jon Povey <Jon.Povey@racelogic.co.uk>
Tested-by: Jon Povey <Jon.Povey@racelogic.co.uk>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Unbanked GPIO irq setup code was overwriting chip_data leading
to the following oops on request_irq()
Unable to handle kernel paging request at virtual address febfffff
pgd = c22dc000
[febfffff] *pgd=00000000
Internal error: Oops: 801 [#1] PREEMPT
Modules linked in: mcu(+) edmak irqk cmemk
CPU: 0 Not tainted (3.0.0-rc7+ #93)
PC is at irq_gc_mask_set_bit+0x68/0x7c
LR is at vprintk+0x22c/0x484
pc : [<c0080c0c>] lr : [<c00457e0>] psr: 60000093
sp : c33e3ba0 ip : c33e3af0 fp : c33e3bc4
r10: c04555bc r9 : c33d4340 r8 : 60000013
r7 : 0000002d r6 : c04555bc r5 : fec67010 r4 : 00000000
r3 : c04734c8 r2 : fec00000 r1 : ffffffff r0 : 00000026
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
Control: 0005317f Table: 822dc000 DAC: 00000015
Process modprobe (pid: 526, stack limit = 0xc33e2270)
Stack: (0xc33e3ba0 to 0xc33e4000)
3ba0: 00000000 c007d3d4 c33e3bcc c04555bc c04555bc c33d4340 c33e3bdc c33e3bc8
3bc0: c007f5f8 c0080bb4 00000000 c04555bc c33e3bf4 c33e3be0 c007f654 c007f5c0
3be0: 00000000 c04555bc c33e3c24 c33e3bf8 c007e6e8 c007f618 c01f2284 c0350af8
3c00: c0405214 bf016c98 00000001 00000000 c33dc008 0000002d c33e3c54 c33e3c28
3c20: c007e888 c007e408 00000001 c23ef880 c33dc000 00000000 c33dc080 c25caa00
3c40: c0487498 bf017078 c33e3c94 c33e3c58 bf016b44 c007e7d4 bf017078 c33dc008
3c60: c25caa08 c33dc008 c33e3c84 bf017484 c25caa00 c25caa00 c01f5f48 c25caa08
3c80: c0496d60 bf017484 c33e3ca4 c33e3c98 c022a698 bf01692c c33e3cd4 c33e3ca8
3ca0: c01f5d88 c022a688 00000000 bf017484 c25caa00 c25caa00 c01f5f48 c25caa08
3cc0: c0496d60 00000000 c33e3cec c33e3cd8 c01f5f8c c01f5d10 00000000 c33e3cf0
3ce0: c33e3d14 c33e3cf0 c01f5210 c01f5f58 c303cb48 c25ecf94 c25caa00 c25caa00
3d00: c25caa34 c33e3dd8 c33e3d34 c33e3d18 c01f6044 c01f51b8 c0496d3c c25caa00
3d20: c044e918 c33e3dd8 c33e3d44 c33e3d38 c01f4ff4 c01f5fcc c33e3d94 c33e3d48
3d40: c01f3d10 c01f4fd8 00000000 c044e918 00000000 00000000 c01f52c0 c034d570
3d60: c33e3d84 c33e3d70 c022bf84 c25caa00 00000000 c044e918 c33e3dd8 c25c2e00
3d80: c0496d60 bf01763c c33e3db4 c33e3d98 c022b1a0 c01f384c c25caa00 c33e3dd8
3da0: 00000000 c33e3dd8 c33e3dd4 c33e3db8 c022b27c c022b0e8 00000000 bf01763c
3dc0: c0451c80 c33e3dd8 c33e3e34 c33e3dd8 bf016f60 c022b210 5f75636d 746e6f63
3de0: 006c6f72 00000000 00000000 00000000 00000000 00000000 00000000 bf0174bc
3e00: 00000000 00989680 00000000 00000020 c0451c80 c0451c80 bf0174dc c01f5eb0
3e20: c33f0f00 bf0174dc c33e3e44 c33e3e38 c01f72f4 bf016e2c c33e3e74 c33e3e48
3e40: c01f5d88 c01f72e4 00000000 c0451c80 c0451cb4 bf0174dc c01f5eb0 c33f0f00
3e60: c0473100 00000000 c33e3e94 c33e3e78 c01f5f44 c01f5d10 00000000 c33e3e98
3e80: bf0174dc c01f5eb0 c33e3ebc c33e3e98 c01f5534 c01f5ec0 c303c038 c3061c30
3ea0: 00003cd8 00098258 bf0174dc c0462ac8 c33e3ecc c33e3ec0 c01f5bec c01f54dc
3ec0: c33e3efc c33e3ed0 c01f4d30 c01f5bdc bf0173a0 c33e2000 00003cd8 00098258
3ee0: bf0174dc c33e2000 c00301a4 bf019000 c33e3f1c c33e3f00 c01f6588 c01f4c8c
3f00: 00003cd8 00098258 00000000 c33e2000 c33e3f2c c33e3f20 c01f777c c01f6524
3f20: c33e3f3c c33e3f30 bf019014 c01f7740 c33e3f7c c33e3f40 c002f3ec bf019010
3f40: 00000000 00003cd8 00098258 bf017518 00000000 00003cd8 00098258 bf017518
3f60: 00000000 c00301a4 c33e2000 00000000 c33e3fa4 c33e3f80 c007b934 c002f3c4
3f80: c00b307c c00b2f48 00003cd8 00000000 00000003 00000080 00000000 c33e3fa8
3fa0: c0030020 c007b8b8 00003cd8 00000000 00098288 00003cd8 00098258 00098240
3fc0: 00003cd8 00000000 00000003 00000080 00098008 00098028 00098288 00000001
3fe0: be892998 be892988 00013d7c 40178740 60000010 00098288 09089041 00200845
Backtrace:
[<c0080ba4>] (irq_gc_mask_set_bit+0x0/0x7c) from [<c007f5f8>] (irq_enable+0x48/0x58)
r6:c33d4340 r5:c04555bc r4:c04555bc
[<c007f5b0>] (irq_enable+0x0/0x58) from [<c007f654>] (irq_startup+0x4c/0x54)
r5:c04555bc r4:00000000
[<c007f608>] (irq_startup+0x0/0x54) from [<c007e6e8>] (__setup_irq+0x2f0/0x3cc)
r5:c04555bc r4:00000000
[<c007e3f8>] (__setup_irq+0x0/0x3cc) from [<c007e888>] (request_threaded_irq+0xc4/0x110)
r8:0000002d r7:c33dc008 r6:00000000 r5:00000001 r4:bf016c98
[<c007e7c4>] (request_threaded_irq+0x0/0x110) from [<bf016b44>] (mcu_spi_probe+0x228/0x37c [mcu])
[<bf01691c>] (mcu_spi_probe+0x0/0x37c [mcu]) from [<c022a698>] (spi_drv_probe+0x20/0x24)
[<c022a678>] (spi_drv_probe+0x0/0x24) from [<c01f5d88>] (driver_probe_device+0x88/0x1b0)
[<c01f5d00>] (driver_probe_device+0x0/0x1b0) from [<c01f5f8c>] (__device_attach+0x44/0x48)
[<c01f5f48>] (__device_attach+0x0/0x48) from [<c01f5210>] (bus_for_each_drv+0x68/0x94)
r5:c33e3cf0 r4:00000000
[<c01f51a8>] (bus_for_each_drv+0x0/0x94) from [<c01f6044>] (device_attach+0x88/0xa0)
r7:c33e3dd8 r6:c25caa34 r5:c25caa00 r4:c25caa00
[<c01f5fbc>] (device_attach+0x0/0xa0) from [<c01f4ff4>] (bus_probe_device+0x2c/0x4c)
r7:c33e3dd8 r6:c044e918 r5:c25caa00 r4:c0496d3c
[<c01f4fc8>] (bus_probe_device+0x0/0x4c) from [<c01f3d10>] (device_add+0x4d4/0x648)
[<c01f383c>] (device_add+0x0/0x648) from [<c022b1a0>] (spi_add_device+0xc8/0x128)
[<c022b0d8>] (spi_add_device+0x0/0x128) from [<c022b27c>] (spi_new_device+0x7c/0xb4)
r7:c33e3dd8 r6:00000000 r5:c33e3dd8 r4:c25caa00
[<c022b200>] (spi_new_device+0x0/0xb4) from [<bf016f60>] (mcu_probe+0x144/0x224 [mcu])
r7:c33e3dd8 r6:c0451c80 r5:bf01763c r4:00000000
[<bf016e1c>] (mcu_probe+0x0/0x224 [mcu]) from [<c01f72f4>] (platform_drv_probe+0x20/0x24)
[<c01f72d4>] (platform_drv_probe+0x0/0x24) from [<c01f5d88>] (driver_probe_device+0x88/0x1b0)
[<c01f5d00>] (driver_probe_device+0x0/0x1b0) from [<c01f5f44>] (__driver_attach+0x94/0x98)
[<c01f5eb0>] (__driver_attach+0x0/0x98) from [<c01f5534>] (bus_for_each_dev+0x68/0x94)
r7:c01f5eb0 r6:bf0174dc r5:c33e3e98 r4:00000000
[<c01f54cc>] (bus_for_each_dev+0x0/0x94) from [<c01f5bec>] (driver_attach+0x20/0x28)
r7:c0462ac8 r6:bf0174dc r5:00098258 r4:00003cd8
[<c01f5bcc>] (driver_attach+0x0/0x28) from [<c01f4d30>] (bus_add_driver+0xb4/0x258)
[<c01f4c7c>] (bus_add_driver+0x0/0x258) from [<c01f6588>] (driver_register+0x74/0x158)
[<c01f6514>] (driver_register+0x0/0x158) from [<c01f777c>] (platform_driver_register+0x4c/0x60)
r7:c33e2000 r6:00000000 r5:00098258 r4:00003cd8
[<c01f7730>] (platform_driver_register+0x0/0x60) from [<bf019014>] (mcu_init+0x14/0x20 [mcu])
[<bf019000>] (mcu_init+0x0/0x20 [mcu]) from [<c002f3ec>] (do_one_initcall+0x38/0x170)
[<c002f3b4>] (do_one_initcall+0x0/0x170) from [<c007b934>] (sys_init_module+0x8c/0x1a4)
[<c007b8a8>] (sys_init_module+0x0/0x1a4) from [<c0030020>] (ret_fast_syscall+0x0/0x2c)
r7:00000080 r6:00000003 r5:00000000 r4:00003cd8
Code: e1844003 e585400c e596300c e5932064 (e7814002)
Fix the issue.
Cc: <stable@vger.kernel.org> # v3.0.x+
Reported-by: Jon Povey <Jon.Povey@racelogic.co.uk>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Make omap_mpuio_alloc_gc() __devinit as omap_gpio_chip_init()
is __devinit. Otherwise we get:
WARNING: vmlinux.o(.devinit.text+0xa10): Section mismatch in reference
from the function omap_gpio_chip_init() to the function .init.text:omap_mpuio_alloc_gc()
The function __devinit omap_gpio_chip_init() references
a function __init omap_mpuio_alloc_gc().
If omap_mpuio_alloc_gc is only used by omap_gpio_chip_init then
annotate omap_mpuio_alloc_gc with a matching annotation.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
These two functions are used in drivers that can be
modules, so they need to be exported.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alan Ott <alan@signal11.us>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The present _get_value routine returns the contents of the GPIO Monitor Pin
Status Register(GPMR) starting from the bit whose value is requested to BIT 0
(irrelevant bits are replace by 0).
For e.g. if we request the value of GPIO 6 in the earlier implementation the
value returned is:
BIT6 followed by 6 0's
whereas it should just return BIT6.
This patch addresses the same.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The chip offers the function to detect the current state of output of the GPO
P3 pins. Useful for reading GPIO output state in Linux' GPIO API, e.g. via
sysfs.
Please note that this only reads back the currently programmed output state,
not the actual electrical level in terms of a GPI function. Finally, GPO3 is
still just an output.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Add missing mask to pin bit selection in gpio-lpc32xx.c
(#define GPIO3_PIN_IN_SEL)
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
While both level- and edge-triggered GPIOs are capable of generating
interrupts, only edge-triggered GPIOs are capable of generating a
module-level wakeup to the PRCM (c.f. 34xx NDA TRM section 25.5.3.2.)
In order to ensure that devices using level-triggered GPIOs as
interrupts can also cause wakeups (e.g. from idle), this patch enables
edge-triggering for wakeup-enabled, level-triggered GPIOs when a GPIO
bank is runtime-suspended (which also happens during idle.)
This fixes a problem found in GPMC-connected network cards with GPIO
interrupts (e.g. smsc911x on Zoom3, Overo, ...) where network booting
with NFSroot was very slow since the GPIO IRQs used by the NIC were
not generating PRCM wakeups, and thus not waking the system from idle.
NOTE: until v3.3, this boot-time problem was somewhat masked because
the UART init prevented WFI during boot until the full serial driver
was available. Preventing WFI allowed regular GPIO interrupts to fire
and this problem was not seen. After the UART runtime PM cleanups, we
no longer avoid WFI during boot, so GPIO IRQs that were not causing
wakeups resulted in very slow IRQ response times.
Tested on platforms using level-triggered GPIOs for network IRQs using
the SMSC911x NIC: 3530/Overo and 3630/Zoom3.
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Adds support for boards which have an STMPE GPIO device without the
interrupt pin connected. This means that no interrupt can be received
but the GPIO pins can still be driven and read.
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Michel Jaouen <michel.jaouen@stericsson.com>
Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The driver is still relying on internal OMAP IRQ defines that
are not relevant anymore if OMAP is built with SPARSE_IRQ.
Replace the defines with the proper IRQ base number.
Clean some comment style issue.
Remove some hidden and ugly cpu_class_is_omap1() inside the
gpio header.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
|
|
Adapt the GPIO driver to retrieve information from a DT file.
Allocate the irq_base dynamically and rename bank->virtual_irq_start
to bank->irq_base.
Change irq_base type to int instead of u16 to match irq_alloc_descs
output.
Add documentation for GPIO properties specific to OMAP.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
|
|
Replace the regular kzalloc and ioremap with the devm_ equivalent
to simplify error handling.
Add the missing devm_request_mem_region to reserve the region used
by the driver.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
|
|
The driver does not need anymore any id to identify the GPIO instance.
Remove every occurence of the bank->id inside the driver.
Remove two trailing spaces.
Add a dev variable for better readability in probe.
Remove unused variable bank->pbase.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
|
|
This is needed in order for the tegra/soc-drivers branch
to work.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
I've seen users getting very confused by the WARN_ON()s for can_sleep
GPIOs in the atomic-safe paths, the discoverability of the non-atomic
version of the API seems to be hampered by the fact that it's defined
in a header file not the .c file where the warnings are.
Add a couple of comments next to the warnings to help people on their
way.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Adding support for the open source gpio on which client
can specify the open source property through GPIO flag
GPIOF_OPEN_SOURCE at the time of gpio request.
The open source pins are normally pulled low and it
cannot be driven to output with value of 0 and so
when client request for setting the pin to LOW, the
gpio will be set to input direction to make pin in tristate
and hence PULL-DOWN on pins will make the state to LOW.
The open source pin can be driven to HIGH by setting output
with value of 1.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Adding support for the open drain gpio on which client
can specify the open drain property through GPIO flag
GPIOF_OPEN_DRAIN at the time of gpio request.
The open drain pins are normally pulled high and it
cannot be driven to output with value of 1 and so
when client request for setting the pin to HIGH, the
gpio will be set to input direction to make pin in tristate
and hence PULL-UP on pins will make the state to HIGH.
The open drain pin can be driven to LOW by setting output
with value of 0.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra into tegra/soc-drivers
Tegra SoC driver support.
Some device tree conversions, some new drivers. and a fix for an issue
introduced in Grant Likely's irq_domain conversion in his tree. Because
of that, this branch depends on his branch to build (but not to merge):
git://git.secretlab.ca/git/linux-2.6.git irqdomain/next
* tag 'tegra-soc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra: (34 commits)
ARM: tegra: uncompress.h: Don't depend on kernel headers
gpio: tegra: Fix build issue due to irq_domain rework.
ARM: tegra: Remove duplicate PMU interrupt inversion code
ARM: tegra: Add a simple PMC driver
ARM: tegra: dma: not required to move requestor when stopping.
ARM: tegra: Fix EMC pdata initialization from registers
gpio: tegra: Parameterize the number of banks
gpio: tegra: Dynamically allocate IRQ base, and support DT
ARM: tegra: Remove use of TEGRA_GPIO_TO_IRQ
ARM: tegra: Pass uncompress.h UART selection to DEBUG_LL
ARM: tegra: uncompress.h: Choose a UART at runtime
ARM: tegra: uncompress.h: Store UART address in a variable
ARM: tegra: Introduce define DEBUG_UART_SHIFT
ARM: tegra: Support Tegra30 in decompressor UART setup
ARM: tegra: Pause DMA when reading transfer count
ARM: tegra: emc: device tree support
ARM: tegra: emc: convert tegra2_emc to a platform driver
ARM: tegra: fuse: add bct strapping reading
ARM: tegra: fuse: add functions to access chip revision
ARM: tegra: fuse: use apbio dma for register access
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Conflicts:
arch/arm/mach-omap1/gpio16xx.c
drivers/gpio/gpio-omap.c
Merge in the runtime-pm-cleanup branch from the gpio tree into
next/cleanup, this resolves a nonobvious merge conflict between
the two branches. Both branches move parts of the gpio-omap
driver into platform code, this takes the superset of both
changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
|
|
Commit 7da5a66 "irq_domain: Remove 'new' irq_domain in favour of the
ppc one" changed the set of available irq domain APIs. Update the Tegra
GPIO driver to account for those changes, to solve a build break.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This way we can remove omap_read/write call from the GPIO driver
and remove include to linux/io.h.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into gpio/next
|
|
pl061 uses same routines for suspend/freeze/poweroff and resume/thaw/restore.
We are only saving and restoring register values on these routines.
During hibernation, in freeze() we take a snapshot of gpio registers. In thaw()
we don't actually need to restore these registers, as power was never shut down
till now. Similarly, in poweroff() we don't need to take snapshot of these
registers again, as it was done during freeze() and by now the image is already
saved on disk.
This patch passes poweroff() and thaw() routines as NULL to avoid this extra
work done.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch converts a number of the powerpc drivers to use the common library
of irq_domain xlate functions, dropping a bunch of lines in the process.
v5: - Remove tsi108 changes from patch
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
|
|
Each revmap type has different arguments for setting up the revmap.
This patch splits up the generator functions so that each revmap type
can do its own setup and the user doesn't need to keep track of how
each revmap type handles the arguments.
This patch also adds a host_data argument to the generators. There are
cases where the host_data pointer will be needed before the function returns.
ie. the legacy map calls the .map callback for each irq before returning.
v2: - Add void *host_data argument to irq_domain_add_*() functions
- fixed failure to compile
- Moved IRQ_DOMAIN_MAP_* defines into irqdomain.c
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
|
|
Hi,
On Wed, Feb 8, 2012 at 8:41 PM, Felipe Balbi <balbi@ti.com> wrote:
> Hi guys,
>
> I have just triggered the folllowing:
>
> [ 84.860321] ======================================================
> [ 84.860321] [ INFO: possible circular locking dependency detected ]
> [ 84.860321] 3.3.0-rc2-00026-ge4e8a39 #474 Not tainted
> [ 84.860321] -------------------------------------------------------
> [ 84.860321] bash/949 is trying to acquire lock:
> [ 84.860321] (sysfs_lock){+.+.+.}, at: [<c0275358>] gpio_value_store+0x24/0xcc
> [ 84.860321]
> [ 84.860321] but task is already holding lock:
> [ 84.860321] (s_active#22){++++.+}, at: [<c016996c>] sysfs_write_file+0xdc/0x184
> [ 84.911468]
> [ 84.911468] which lock already depends on the new lock.
> [ 84.911468]
> [ 84.920043]
> [ 84.920043] the existing dependency chain (in reverse order) is:
> [ 84.920043]
> [ 84.927886] -> #1 (s_active#22){++++.+}:
> [ 84.927886] [<c008f640>] check_prevs_add+0xdc/0x150
> [ 84.927886] [<c008fc18>] validate_chain.clone.24+0x564/0x694
> [ 84.927886] [<c0090cdc>] __lock_acquire+0x49c/0x980
> [ 84.951660] [<c0091838>] lock_acquire+0x98/0x100
> [ 84.951660] [<c016a8e8>] sysfs_deactivate+0xb0/0x100
> [ 84.962982] [<c016b1b4>] sysfs_addrm_finish+0x2c/0x6c
> [ 84.962982] [<c016b8bc>] sysfs_remove_dir+0x84/0x98
> [ 84.962982] [<c02590d8>] kobject_del+0x10/0x78
> [ 84.974670] [<c02c29e8>] device_del+0x140/0x170
> [ 84.974670] [<c02c2a24>] device_unregister+0xc/0x18
> [ 84.985382] [<c0276894>] gpio_unexport+0xbc/0xdc
> [ 84.985382] [<c02768c8>] gpio_free+0x14/0xfc
> [ 85.001708] [<c0276a28>] unexport_store+0x78/0x8c
> [ 85.001708] [<c02c5af8>] class_attr_store+0x18/0x24
> [ 85.007293] [<c0169990>] sysfs_write_file+0x100/0x184
> [ 85.018981] [<c0109d48>] vfs_write+0xb4/0x148
> [ 85.018981] [<c0109fd0>] sys_write+0x40/0x70
> [ 85.018981] [<c0013cc0>] ret_fast_syscall+0x0/0x3c
> [ 85.035003]
> [ 85.035003] -> #0 (sysfs_lock){+.+.+.}:
> [ 85.035003] [<c008f54c>] check_prev_add+0x680/0x698
> [ 85.035003] [<c008f640>] check_prevs_add+0xdc/0x150
> [ 85.052093] [<c008fc18>] validate_chain.clone.24+0x564/0x694
> [ 85.052093] [<c0090cdc>] __lock_acquire+0x49c/0x980
> [ 85.052093] [<c0091838>] lock_acquire+0x98/0x100
> [ 85.069885] [<c047e280>] mutex_lock_nested+0x3c/0x2f4
> [ 85.069885] [<c0275358>] gpio_value_store+0x24/0xcc
> [ 85.069885] [<c02c18dc>] dev_attr_store+0x18/0x24
> [ 85.087158] [<c0169990>] sysfs_write_file+0x100/0x184
> [ 85.087158] [<c0109d48>] vfs_write+0xb4/0x148
> [ 85.098297] [<c0109fd0>] sys_write+0x40/0x70
> [ 85.098297] [<c0013cc0>] ret_fast_syscall+0x0/0x3c
> [ 85.109069]
> [ 85.109069] other info that might help us debug this:
> [ 85.109069]
> [ 85.117462] Possible unsafe locking scenario:
> [ 85.117462]
> [ 85.117462] CPU0 CPU1
> [ 85.128417] ---- ----
> [ 85.128417] lock(s_active#22);
> [ 85.128417] lock(sysfs_lock);
> [ 85.128417] lock(s_active#22);
> [ 85.142486] lock(sysfs_lock);
> [ 85.151794]
> [ 85.151794] *** DEADLOCK ***
> [ 85.151794]
> [ 85.151794] 2 locks held by bash/949:
> [ 85.158020] #0: (&buffer->mutex){+.+.+.}, at: [<c01698b8>] sysfs_write_file+0x28/0x184
> [ 85.170349] #1: (s_active#22){++++.+}, at: [<c016996c>] sysfs_write_file+0xdc/0x184
> [ 85.170349]
> [ 85.178588] stack backtrace:
> [ 85.178588] [<c001b824>] (unwind_backtrace+0x0/0xf0) from [<c008de64>] (print_circular_bug+0x100/0x114)
> [ 85.193023] [<c008de64>] (print_circular_bug+0x100/0x114) from [<c008f54c>] (check_prev_add+0x680/0x698)
> [ 85.193023] [<c008f54c>] (check_prev_add+0x680/0x698) from [<c008f640>] (check_prevs_add+0xdc/0x150)
> [ 85.212524] [<c008f640>] (check_prevs_add+0xdc/0x150) from [<c008fc18>] (validate_chain.clone.24+0x564/0x694)
> [ 85.212524] [<c008fc18>] (validate_chain.clone.24+0x564/0x694) from [<c0090cdc>] (__lock_acquire+0x49c/0x980)
> [ 85.233306] [<c0090cdc>] (__lock_acquire+0x49c/0x980) from [<c0091838>] (lock_acquire+0x98/0x100)
> [ 85.233306] [<c0091838>] (lock_acquire+0x98/0x100) from [<c047e280>] (mutex_lock_nested+0x3c/0x2f4)
> [ 85.242614] [<c047e280>] (mutex_lock_nested+0x3c/0x2f4) from [<c0275358>] (gpio_value_store+0x24/0xcc)
> [ 85.261840] [<c0275358>] (gpio_value_store+0x24/0xcc) from [<c02c18dc>] (dev_attr_store+0x18/0x24)
> [ 85.261840] [<c02c18dc>] (dev_attr_store+0x18/0x24) from [<c0169990>] (sysfs_write_file+0x100/0x184)
> [ 85.271240] [<c0169990>] (sysfs_write_file+0x100/0x184) from [<c0109d48>] (vfs_write+0xb4/0x148)
> [ 85.290008] [<c0109d48>] (vfs_write+0xb4/0x148) from [<c0109fd0>] (sys_write+0x40/0x70)
> [ 85.298400] [<c0109fd0>] (sys_write+0x40/0x70) from [<c0013cc0>] (ret_fast_syscall+0x0/0x3c)
> -bash: echo: write error: Operation not permitted
>
> the way to trigger is:
>
> root@legolas:~# cd /sys/class/gpio/
> root@legolas:/sys/class/gpio# echo 2 > export
> root@legolas:/sys/class/gpio# echo 2 > unexport
> root@legolas:/sys/class/gpio# echo 2 > export
> root@legolas:/sys/class/gpio# cd gpio2/
> root@legolas:/sys/class/gpio/gpio2# echo 1 > value
Looks 'sysfs_lock' needn't to be held for unregister, so the patch below may
fix the problem.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch drops the powerpc-specific irq_host structures and uses the common
irq_domain strucutres defined in linux/irqdomain.h. It also fixes all
the users to use the new structure names.
Renaming irq_host to irq_domain has been discussed for a long time, and this
patch is a step in the process of generalizing the powerpc virq code to be
usable by all architecture.
An astute reader will notice that this patch actually removes the irq_host
structure instead of renaming it. This is because the irq_domain structure
already exists in include/linux/irqdomain.h and has the needed data members.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
|
|
Tegra20's GPIO controller has 7 banks, and Tegra30's controller has 8
banks. Allow the number of banks to be configured at run-time by the
device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Enhance the driver to dynamically allocate the base IRQ number, and
create an IRQ domain for itself. The use of an IRQ domain ensures that
any device tree node interrupts properties are correctly parsed.
Describe interrupt-related properties in the device tree binding docs,
and the contents of "child" node interrupts property.
Update tegra*.dtsi to specify the required interrupt-related properties.
Finally, remove the definition of TEGRA_GPIO_TO_IRQ; this macro no longer
gives correct results since the IRQ numbers for GPIOs are dynamically
allocated.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
GPIO IP revisions such as those used in OMAP4 have a set_dataout
while the previous revisions used a single dataout register.
Depending on what is available restore the dataout settings
to the right register.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Setup the dataout register before restoring OE. This is to make
sure that we have valid data in dataout register which would be
made available in output pins as soon as OE is enabled. Else,
there is risk of unknown data getting out into gpio pins.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Setup the interrupt enable registers only after we have configured the
required edge and required configurations, not before, to prevent
spurious events as part of restore routine.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
GPIO debounce registers need to be saved and restored for proper functioning
of driver.
Signed-off-by: Nishanth Menon <nm@ti.com>
tarun.kanti@ti.com: Debounce context save is moved to _set_gpio_debounce()
as part of dynamic context save to remove overhead.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
