| Age | Commit message (Collapse) | Author |
|---|
|
The code for .get_multiple() has bugs:
1. The simple .get_multiple() just reads a register, masks it
and sets the return value. This is not correct: we only want to
assign values (whether 0 or 1) to the bits that are set in the
mask. Fix this by using &= ~mask to clear all bits in the mask
and then |= val & mask to set the corresponding bits from the
read.
2. The bgpio_get_multiple_be() call has a similar problem: it
uses the |= operator to set the bits, so only the bits in the
mask are affected, but it misses to clear all returned bits
from the mask initially, so some bits will be returned
erroneously set to 1.
3. The bgpio_get_set_multiple() again fails to clear the bits
from the mask.
4. find_next_bit() wasn't handled correctly, use a totally
different approach for one function and change the other
function to follow the design pattern of assigning the first
bit to -1, then use bit + 1 in the for loop and < num_iterations
as break condition.
Fixes: 80057cb417b2 ("gpio-mmio: Use the new .get_multiple() callback")
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Reported-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reported-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since commit f11a04464ae57e8d ("i2c: gpio: Enable working over slow
can_sleep GPIOs"), probing the i2c RTC connected to an i2c-gpio bus on
r8a7740/armadillo fails with:
rtc-s35390a 0-0030: error resetting chip
rtc-s35390a: probe of 0-0030 failed with error -5
More debug code reveals:
i2c i2c-0: master_xfer[0] R, addr=0x30, len=1
i2c i2c-0: NAK from device addr 0x30 msg #0
s35390a_get_reg: ret = -6
Commit 02e479808b5d62f8 ("gpio: Alter semantics of *raw* operations to
actually be raw") moved open drain/source handling from
gpiod_set_raw_value_commit() to gpiod_set_value(), but forgot to take
into account that gpiod_set_value_cansleep() also needs this handling.
The i2c protocol mandates that i2c signals are open drain, hence i2c
communication fails.
Fix this by adding the missing handling to gpiod_set_value_cansleep(),
using a new common helper gpiod_set_value_nocheck().
Fixes: 02e479808b5d62f8 ("gpio: Alter semantics of *raw* operations to actually be raw")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[removed underscore syntax, added kerneldoc]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The 'early' argument of irq_domain_activate_irq() is actually used to
denote reservation mode. To avoid confusion, rename it before abuse
happens.
No functional change.
Fixes: 72491643469a ("genirq/irqdomain: Update irq_domain_ops.activate() signature")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexandru Chirvasitu <achirvasub@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
|
|
The recent extension of irq_set_lockdep_class() with a second argument
added the new lockdep class to the mrcmstb driver, but used the already
existing lockdep class as second argument, which leaves the new lockdep
class defined but unused.
Use the new lockdep class as that's what the change intended to do.
Fixes: 39c3fd58952d ("kernel/irq: Extend lockdep class for request mutex")
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: linus.walleij@linaro.org
|
|
The IRQ code already has support for lockdep class for the lock mutex
in an interrupt descriptor. Extend this to add a second class for the
request mutex in the descriptor. Not having a class is resulting in
false positive splats in some code paths.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: linus.walleij@linaro.org
Cc: grygorii.strashko@ti.com
Cc: f.fainelli@gmail.com
Link: https://lkml.kernel.org/r/1512234664-21555-1-git-send-email-andrew@lunn.ch
|
|
Following commit 9427ecbed46cc ("gpio: Rework of_gpiochip_set_names()
to use device property accessors"), "gpio-line-names" DT property is
not retrieved anymore when chip->parent is not set by the driver.
This is due to OF based property reads having been replaced by device
based property reads.
This patch fixes that by making use of
fwnode_property_read_string_array() instead of
device_property_read_string_array() and handing over either
of_fwnode_handle(chip->of_node) or dev_fwnode(chip->parent)
to that function.
Fixes: 9427ecbed46cc ("gpio: Rework of_gpiochip_set_names() to use device property accessors")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Revert changes introduced by commit f0fbe7bce733 ("gpio: Move irqdomain
into struct gpio_irq_chip") as they are not aplicable to this driver.
Reported-by: Russell King - ARM Linux <linux@armlinux.org.uk>
Fixes: f0fbe7bce733 ("gpio: Move irqdomain into struct gpio_irq_chip")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Despite commit 55020c8056a8 ("of: Add vendor prefix for ON Semiconductor
Corp.") was made long ago, the latter commit 9f49f6dd0473 ("gpio: pca953x:
add onsemi,pca9654 id") made use of another, undocumented vendor prefix.
Since such prefix doesn't seem to be used in any device trees, I think we
can just fix the "compatible" string in the driver and the bindings and be
done with that...
Fixes: 9f49f6dd0473 ("gpio: pca953x: add onsemi,pca9654 id")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As per the re-design assign the first bank regs for unbanked
irq case. This was missed out in the original patch.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Fixes: b5cf3fd827d2e1 ("gpio: davinci: Redesign driver to accommodate ngpios in one gpio chip")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit 7ebc194d0fd4bb0f ("gpio: 74x164: Introduce 'enable-gpios'
property") added a new member gpiod_oe to the end of the struct
gen_74x164_chip, after the zero-length buffer array.
However, this buffer is a flexible array, allocated together with the
structure during .probe(). As the buffer is no longer the last member,
writing to it corrupts the newly added member after it.
During device removal, the corrupted member will be used as a pointer,
leading to a crash.
This went unnoticed, as the flexible array was declared as "buffer[0]"
instead of "buffer[]", and thus did not trigger a "flexible array member
not at end of struct" error from gcc.
Move the gpiod_oe field up to fix this, and drop the zero from the array
size to prevent future similar bugs.
Fixes: 7ebc194d0fd4bb0f ("gpio: 74x164: Introduce 'enable-gpios' property")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.15 kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into a
menuconfig option. This obviously has the implication of making the
subsystem menu visible in menuconfig. This is happening because of
two things:
(a) Intel have started to deploy and depend on pin controllers in
a way that is affecting users directly. This happens on the
highly integrated laptop chipsets named after geographical
places: baytrail, broxton, cannonlake, cedarfork, cherryview,
denverton, geminilake, lewisburg, merrifield, sunrisepoint...
It started a while back and now it is ever more evident that
this is crucial infrastructure for x86 laptops and not an
embedded obscurity anymore. Users need to be aware.
(b) Pin control expanders on I2C and SPI that are arch-agnostic.
Currently Semtech SX150X and Microchip MCP28x08 but more are
expected. Users will have to be able to configure these in
directly for their set-up.
- Just go and select GPIOLIB now that we made sure that GPIOLIB is a
very vanilla subsystem. Do not depend on it, if we need it, select
it.
- Exposing the pin control subsystem in menuconfig uncovered a bunch
of obscure bugs that are now hopefully fixed, all more or less
pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and GPIO.
- New support for clock skew/delay generic DT bindings and generic
pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying"
* tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (91 commits)
pinctrl: gemini: Fix missing pad descriptions
pinctrl: Add some depends on HAS_IOMEM
pinctrl: samsung/s3c24xx: add CONFIG_OF dependency
pinctrl: gemini: Fix GMAC groups
pinctrl: qcom: spmi-gpio: Add pmi8994 gpio support
pinctrl: ti-iodelay: remove redundant unused variable dev
pinctrl: max77620: Use common error handling code in max77620_pinconf_set()
pinctrl: gemini: Implement clock skew/delay config
pinctrl: gemini: Use generic DT parser
pinctrl: Add skew-delay pin config and bindings
pinctrl: armada-37xx: Add edge both type gpio irq support
pinctrl: uniphier: remove eMMC hardware reset pin-mux
pinctrl: rockchip: Add iomux-route switching support for rk3288
pinctrl: intel: Add Intel Cedar Fork PCH pin controller support
pinctrl: intel: Make offset to interrupt status register configurable
pinctrl: sunxi: Enforce the strict mode by default
pinctrl: sunxi: Disable strict mode for old pinctrl drivers
pinctrl: sunxi: Introduce the strict flag
pinctrl: sh-pfc: Save/restore registers for PSCI system suspend
pinctrl: sh-pfc: r8a7796: Use generic IOCTRL register description
...
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"This contains two bigger than usual tree-wide changes this time. They
all have proper acks, caused no merge conflicts in linux-next where
they have been for a while. They are namely:
- to-gpiod conversion of the i2c-gpio driver and its users (touching
arch/* and drivers/mfd/*)
- adding a sbs-manager based on I2C core updates to SMBus alerts
(touching drivers/power/*)
Other notable changes:
- i2c_boardinfo can now carry a dev_name to be used when the device
is created. This is because some devices in ACPI world need fixed
names to find the regulators.
- the designware driver got a long discussed overhaul of its PM
handling. img-scb and davinci got PM support, too.
- at24 driver has way better OF support. And it has a new maintainer.
Thanks Bartosz for stepping up!
The rest is regular driver updates and fixes"
* 'i2c/for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (55 commits)
ARM: sa1100: simpad: Correct I2C GPIO offsets
i2c: aspeed: Deassert reset in probe
eeprom: at24: Add OF device ID table
MAINTAINERS: new maintainer for AT24 driver
i2c: nuc900: remove platform_data, too
i2c: thunderx: Remove duplicate NULL check
i2c: taos-evm: Remove duplicate NULL check
i2c: Make i2c_unregister_device() NULL-aware
i2c: xgene-slimpro: Support v2
i2c: mpc: remove useless variable initialization
i2c: omap: Trigger bus recovery in lockup case
i2c: gpio: Add support for named gpios in DT
dt-bindings: i2c: i2c-gpio: Add support for named gpios
i2c: gpio: Local vars in probe
i2c: gpio: Augment all boardfiles to use open drain
i2c: gpio: Enforce open drain through gpiolib
gpio: Make it possible for consumers to enforce open drain
i2c: gpio: Convert to use descriptors
power: supply: sbs-message: fix some code style issues
power: supply: sbs-battery: remove unchecked return var
...
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.15 kernel cycle:
Core:
- Fix the semantics of raw GPIO to actually be raw. No inversion
semantics as before, but also no open draining, and allow the raw
operations to affect lines used for interrupts as the caller
supposedly knows what they are doing if they are getting the big
hammer.
- Rewrote the __inner_function() notation calls to names that make
more sense. I just find this kind of code disturbing.
- Drop the .irq_base() field from the gpiochip since now all IRQs are
mapped dynamically. This is nice.
- Support for .get_multiple() in the core driver API. This allows us
to read several GPIO lines with a single register read. This has
high value for some usecases: it can be used to create
oscilloscopes and signal analyzers and other things that rely on
reading several lines at exactly the same instant. Also a generally
nice optimization. This uses the new assign_bit() macro from the
bitops lib that was ACKed by Andrew Morton and is implemented for
two drivers, one of them being the generic MMIO driver so everyone
using that will be able to benefit from this.
- Do not allow requests of Open Drain and Open Source setting of a
GPIO line simultaneously. If the hardware actually supports
enabling both at the same time the electrical result would be
disastrous.
- A new interrupt chip core helper. This will be helpful to deal with
"banked" GPIOs, which means GPIO controllers with several logical
blocks of GPIO inside them. This is several gpiochips per device in
the device model, in contrast to the case when there is a 1-to-1
relationship between a device and a gpiochip.
New drivers:
- Maxim MAX3191x industrial serializer, a very interesting piece of
professional I/O hardware.
- Uniphier GPIO driver. This is the GPIO block from the recent
Socionext (ex Fujitsu and Panasonic) platform.
- Tegra 186 driver. This is based on the new banked GPIO
infrastructure.
Other improvements:
- Some documentation improvements.
- Wakeup support for the DesignWare DWAPB GPIO controller.
- Reset line support on the DesignWare DWAPB GPIO controller.
- Several non-critical bug fixes and improvements for the Broadcom
BRCMSTB driver.
- Misc non-critical bug fixes like exotic errorpaths, removal of dead
code etc.
- Explicit comments on fall-through switch() statements"
* tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (65 commits)
gpio: tegra186: Remove tegra186_gpio_lock_class
gpio: rcar: Add r8a77995 (R-Car D3) support
pinctrl: bcm2835: Fix some merge fallout
gpio: Fix undefined lock_dep_class
gpio: Automatically add lockdep keys
gpio: Introduce struct gpio_irq_chip.first
gpio: Disambiguate struct gpio_irq_chip.nested
gpio: Add Tegra186 support
gpio: Export gpiochip_irq_{map,unmap}()
gpio: Implement tighter IRQ chip integration
gpio: Move lock_key into struct gpio_irq_chip
gpio: Move irq_valid_mask into struct gpio_irq_chip
gpio: Move irq_nested into struct gpio_irq_chip
gpio: Move irq_chained_parent to struct gpio_irq_chip
gpio: Move irq_default_type to struct gpio_irq_chip
gpio: Move irq_handler to struct gpio_irq_chip
gpio: Move irqdomain into struct gpio_irq_chip
gpio: Move irqchip into struct gpio_irq_chip
gpio: Introduce struct gpio_irq_chip
pinctrl: armada-37xx: remove unused variable
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq core updates from Thomas Gleixner:
"A rather large update for the interrupt core code and the irq chip drivers:
- Add a new bitmap matrix allocator and supporting changes, which is
used to replace the x86 vector allocator which comes with separate
pull request. This allows to replace the convoluted nested loop
allocation function in x86 with a facility which supports the
recently added property of managed interrupts proper and allows to
switch to a best effort vector reservation scheme, which addresses
problems with vector exhaustion.
- A large update to the ARM GIC-V3-ITS driver adding support for
range selectors.
- New interrupt controllers:
- Meson and Meson8 GPIO
- BCM7271 L2
- Socionext EXIU
If you expected that this will stop at some point, I have to
disappoint you. There are new ones posted already. Sigh!
- STM32 interrupt controller support for new platforms.
- A pile of fixes, cleanups and updates to the MIPS GIC driver
- The usual small fixes, cleanups and updates all over the place.
Most visible one is to move the irq chip drivers Kconfig switches
into a separate Kconfig menu"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
genirq: Fix type of shifting literal 1 in __setup_irq()
irqdomain: Drop pointless NULL check in virq_debug_show_one
genirq/proc: Return proper error code when irq_set_affinity() fails
irq/work: Use llist_for_each_entry_safe
irqchip: mips-gic: Print warning if inherited GIC base is used
irqchip/mips-gic: Add pr_fmt and reword pr_* messages
irqchip/stm32: Move the wakeup on interrupt mask
irqchip/stm32: Fix initial values
irqchip/stm32: Add stm32h7 support
dt-bindings/interrupt-controllers: Add compatible string for stm32h7
irqchip/stm32: Add multi-bank management
irqchip/stm32: Select GENERIC_IRQ_CHIP
irqchip/exiu: Add support for Socionext Synquacer EXIU controller
dt-bindings: Add description of Socionext EXIU interrupt controller
irqchip/gic-v3-its: Fix VPE activate callback return value
irqchip: mips-gic: Make IPI bitmaps static
irqchip: mips-gic: Share register writes in gic_set_type()
irqchip: mips-gic: Remove gic_vpes variable
irqchip: mips-gic: Use num_possible_cpus() to reserve IPIs
irqchip: mips-gic: Configure EIC when CPUs come online
...
|
|
This is no longer required after commit 959bc7b22bd2
("gpio: Automatically add lockdep keys")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
The struct is wrong, this is named lock_class_key.
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In order to avoid lockdep boilerplate in individual drivers, turn the
gpiochip_add_data() function into a macro that creates a unique class
key for each driver.
Note that this has the slight disadvantage of adding a key for each
driver registered with the system. However, these keys are 8 bytes in
size, which is negligible and a small price to pay for generic
infrastructure.
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
[renane __gpiochip_add_data() to gpiochip_add_data_with_key]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some GPIO chips cannot support sparse IRQ numbering and therefore need
to manually allocate their interrupt descriptors statically. For these
cases, a driver can pass the first allocated IRQ via the struct
gpio_irq_chip's "first" field and thereby cause the IRQ domain to map
all IRQs during initialization.
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The nested field in struct gpio_irq_chip currently has two meanings. On
one hand it marks an IRQ chip as being nested (as opposed to chained),
while on the other hand it also means that an IRQ chip uses nested
thread handlers.
However, nested IRQ chips can already be identified by the fact that
they don't pass a parent handler (the driver would instead already have
installed a nested handler using request_irq()).
Therefore, the only use for the nested attribute is to inform gpiolib
that an IRQ chip uses nested thread handlers (as opposed to regular,
non-threaded handlers). To clarify its purpose, rename the field to
"threaded".
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Tegra186 has two GPIO controllers that are largely register compatible
between one another but are completely different from the controller
found on earlier generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Export these functions so that drivers can explicitly use these when
setting up their IRQ domain.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Currently GPIO drivers are required to add the GPIO chip and its
corresponding IRQ chip separately, which can result in a lot of
boilerplate. Use the newly introduced struct gpio_irq_chip, embedded in
struct gpio_chip, that drivers can fill in if they want the GPIO core
to automatically register the IRQ chip associated with a GPIO chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio into i2c/for-4.15
Refactor i2c-gpio and its users to use gpiod. Done by GPIO maintainer
LinusW.
|
|
Commit fd9c963c5661 ("gpio: mb86s70: Return error if requesting an
already assigned gpio") adds code that infers from the state of the
GPIO Pin Function Register (PFR) whether a GPIO has been assigned
already. This assumes that the pin functions are set to 'peripheral'
when the driver is loaded, which is not guaranteed. Also, the GPIO
layer is perfectly capable of keeping track of which GPIOs have been
assigned already, so we shouldn't need this check in the first place.
This reverts commit fd9c963c5661af3403e77e312c0d9941773b6c1b.
Cc: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In order to reuse this driver for the Socionext Synquacer SC2A11 SoC,
which inherited this IP from Fujitsu, remove the ARCH_MB86S7X Kconfig
dependency, and revert the changes that prevent it from being built as
a module.
This reverts commits d65aa4b67b4f47f303bdeaef1e4d42ef18e6b293 and
d5610e514e92144d19bd5e39e5cf3804bbf85f3e.
Cc: Geliang Tang <geliangtang@gmail.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[Folded in module_platform_driver() fixup]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This commit corrects problems with the previous wake implementation
by implementing suspend and resume power management operations and
the driver shutdown operation.
Wake masks are used to keep track of which GPIO should wake the
device. On suspend the GPIO state is saved and the possible wakeup
sources are explicitly unmasked in the hardware. Non-wakeup sources
are explicitly masked so IRQCHIP_MASK_ON_SUSPEND is no longer
necessary. The saved state of the GPIO is restored upon resume.
It is important not to write to the GPIO status register since this
has the effect of clearing bits. The status register is explicitly
removed from the register save and restore to ensure this.
The shutdown operation allows the hardware to be put into the same
quiesced state as the suspend operation and removes the need for
the reboot notifier.
Unfortunately, there appears to be some confusion about whether
a pending disabled wake interrupt should wake the system. If a wake
capable interrupt is disabled using the default "lazy disable"
behavior and it is triggered before the suspend_device_irq call
the interrupt hardware will be acknowledged by mask_ack_irq and the
IRQS_PENDING flag is added to its state. However, the IRQS_PENDING
flag of wake interrupts is not checked to prevent the transition to
suspend and the hardware has been acked which prevents its wakeup.
If the lazy disabled interrupt is triggered after the call to
suspend_device_irqs then the wakeup logic will abort the suspend.
The irq_disable method is defined by this GPIO driver to prevent
lazy disable so that the pending hardware state remains asserted
allowing the hardware to wake and providing a consistent behavior.
In addition, the IRQ_DISABLE_UNLAZY flag is set for the non-wake
parent interrupt as a convenience to prevent the need to add code
to the brcmstb_gpio_irq_handler to support "lazy disable" of the
non-wake parent interrupt when it is disabled during suspend and
resume. Chained interrupt parents are not normally disabled, but
these GPIO devices have different parent interrupts for wake and
non-wake handling. It is convenient to mask the non-wake parent
when suspending to preserve the hardware state for proper wakeup
accounting when the driver is resumed.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIOLIB IRQ chip helpers were very appealing, but badly broke
the 1:1 mapping between a GPIO controller's device_node and its
interrupt domain.
When another device-tree node references a GPIO device as its
interrupt parent, the irq_create_of_mapping() function looks for
the irq domain of the GPIO device and since all bank irq domains
reference the same GPIO device node it always resolves to the irq
domain of the first bank regardless of which bank the number of
the GPIO should resolve. This domain can only map hwirq numbers
0-31 so interrupts on GPIO above that can't be mapped by the
device-tree.
This commit effectively reverts the patch from Gregory Fong [1]
that was accepted upstream and replaces it with a consolidated
irq domain implementation with one larger interrupt domain per
GPIO controller instance spanning multiple GPIO banks based on
an earlier patch [2] also submitted by Gregory Fong.
[1] https://patchwork.kernel.org/patch/6921561/
[2] https://patchwork.kernel.org/patch/6347811/
Fixes: 19a7b6940b78 ("gpio: brcmstb: Add interrupt and wakeup source support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Gregory Fong <gregory.0xf0@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This commit corrects a bug when configuring the GPIO hardware for
IRQ_TYPE_LEVEL_LOW and IRQ_TYPE_LEVEL_HIGH interrupt types. The
hardware is now correctly configured to support those types.
Fixes: 19a7b6940b78 ("gpio: brcmstb: Add interrupt and wakeup source support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Reading and writing the gpio bank status register each time a pending
interrupt bit is serviced could cause new pending bits to be cleared
without servicing the associated interrupts.
By using the handle_level_irq flow instead of the handle_simple_irq
flow we get proper handling of interrupt masking as well as acking
of interrupts. The irq_ack method is added to support this.
Fixes: 19a7b6940b78 ("gpio: brcmstb: Add interrupt and wakeup source support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The basic memory-mapped GPIO controller lock must be released
before calling the registered GPIO interrupt handlers to allow
the interrupt handlers to access the hardware.
Examples of why a GPIO interrupt handler might want to access
the GPIO hardware include an interrupt that is configured to
trigger on rising and falling edges that needs to read the
current level of the input to know how to respond, or an
interrupt that causes a change in a GPIO output in the same
bank. If the lock is not released before enterring the handler
the hardware accesses will deadlock when they attempt to grab
the lock.
Since the lock is only needed to protect the calculation of
unmasked pending interrupts create a dedicated function to
perform this and hide the complexity.
Fixes: 19a7b6940b78 ("gpio: brcmstb: Add interrupt and wakeup source support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This commit allows a wakeup parent interrupt to be shared between
instances.
It also removes the redundant can_wake member of the private data
structure by using whether the parent_wake_irq has been defined to
indicate that the GPIO device can wake.
Fixes: 19a7b6940b78 ("gpio: brcmstb: Add interrupt and wakeup source support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add a jump target so that a bit of exception handling can be better reused
at the end of this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Using devm_ioremap_resource() has several advantages over devm_ioremap():
- it checks the passed resource's validity;
- it calls devm_request_mem_region() to check for the resource overlap;
- it prints an error message in case of error.
We can call devm_ioremap_resource() instead of devm_ioremap_nocache()
as ioremap() and ioremap_nocache() are implemented identically on ARM.
Doing this saves 2 LoCs and 80 bytes (AArch64 gcc 4.8.5).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some busses, like I2C, strictly need to have the line handled
as open drain, i.e. not actively driven high. For this reason
the i2c-gpio.c bit-banged I2C driver is reimplementing open
drain handling outside of gpiolib.
This is not very optimal. Instead make it possible for a
consumer to explcitly express that the line must be handled
as open drain instead of allowing local hacks papering over
this issue.
The descriptor tables, whether DT, ACPI or board files, should
of course have flagged these lines as open drain. E.g.:
enum gpio_lookup_flags GPIO_OPEN_DRAIN for a board file, or
gpios = <&foo 42 GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN>; in a
device tree using <dt-bindings/gpio/gpio.h>
But more often than not, these descriptors are wrong. So
we need to make it possible for consumers to enforce this
open drain behaviour.
We now have two new enumerated GPIO descriptor config flags:
GPIOD_OUT_LOW_OPEN_DRAIN and GPIOD_OUT_HIGH_OPEN_DRAIN
that will set up the lined enforced as open drain as output
low or high, using open drain (if the driver supports it)
or using open drain emulation (setting the line as input
to drive it high) from the gpiolib core.
Cc: linux-gpio@vger.kernel.org
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It is possible to read all lines of a generic MMIO GPIO chip
with a single register read so support this if we are in
native endianness.
Add an especially quirky callback to read multiple lines for
the variants that require you to read values from the
output registers if and only if the line is set as output.
We managed to do that with a maximum of two register reads,
and just one read if the requested lines are all input or all
output.
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The vtable call pin2mask() was introducing a vtable function call
in every gpiochip callback for a generic MMIO GPIO chip. This was
not exactly efficient. (Maybe link-time optimization could get rid of
it, I don't know.)
After removing all external calls into this API we can make it a
boolean flag in the struct gpio_chip call and sink the function into
the gpio-mmio driver yielding encapsulation and potential speedups.
Cc: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The MPC8xxx driver is always instantiating its generic GPIO functions
with the flag BGPIOF_BIG_ENDIAN. This means "big-endian bit order"
and means the bits representing the GPIO lines in the registers are
reversed around 31 bits so line 0 is at bit 31 and so forth down to
line 31 in bit 0.
Instead of looping into the generic MMIO gpio to do the simple
calculation of a bitmask, through a vtable call with two parameters
likely using stack frames etc (unless the compiler optimize it)
and obscuring the view for the programmer, let's just open-code
what the call does. This likely executes faster, saves space and
makes the code easier to read.
Cc: Liu Gang <Gang.Liu@nxp.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The pin2mask() accessor only shuffles BIT ORDER in big endian systems,
i.e. the bitstuffing is swizzled big endian so "bit 0" is bit 7 or
bit 15 or bit 31 or so.
The brcmstb only uses big endian BYTE ORDER which will be taken car of
by the ->write_reg() callback.
Just use BIT(offset) to assign the bit.
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The pin2mask() accessor only shuffles BIT ORDER in big endian systems,
i.e. the bitstuffing is swizzled big endian so "bit 0" is bit 7 or
bit 15 or bit 31 or so.
The grgpio only uses big endian BYTE ORDER which will be taken car of
by the ->write_reg() callback.
Just use BIT(offset) to assign the bit.
Acked-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When no flags are given, the native endianness is used to access
the MMIO registers, and the pin2mask() call can simply be
converted to a BIT() call, as per the default pin2mask()
implementation in gpio-mmio.c.
Cc: Kelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
