| Age | Commit message (Collapse) | Author |
|---|
|
Typcasting "irq_state" leads to the below static checker warning:
The fix is to declare "irq_state" as unsigned long instead of u32.
drivers/gpio/gpio-sifive.c:97 sifive_gpio_irq_enable()
warn: passing casted pointer '&chip->irq_state' to
'assign_bit()' 32 vs 64.
Fixes: 96868dce644d ("gpio/sifive: Add GPIO driver for SiFive SoCs")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Link: https://lore.kernel.org/r/1580189061-14091-1-git-send-email-yash.shah@sifive.com
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Care is taken with "index", however with the current version
the actual xgpio_writereg is using index for data but
xgpio_regoffset(chip, i) for the offset. And since i is already
incremented it is incorrect. This patch fixes it so that index
is used for the offset too.
Cc: stable@vger.kernel.org
Signed-off-by: Paul Thomas <pthomas8589@gmail.com>
Link: https://lore.kernel.org/r/20200125221410.8022-1-pthomas8589@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Remove unnecessary argument when setting PIN_CONFIG_BIAS_DISABLE. No
argument is expected by pinctrl, so removing it should be harmless.
Fixes: 2148ad7790ea ("gpiolib: add support for disabling line bias")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
They are defined in gpio/driver.h now.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Commit d90f36851d65 ("gpiolib: have a single place of calling
set_config()") introduced a regression where we don't pass the right
variable as argument to the set_config() callback of gpio driver from
gpio_set_config(). After reverting two additional patches that came
on top of it - this addresses the issue by changing the type of the last
argument of gpio_do_set_config() to unsigned long and making sure the
packed config variable is actually used in gpio_set_config().
Fixes: d90f36851d65 ("gpiolib: have a single place of calling set_config()")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
|
|
This reverts commit e5e42ad224a040f93bf112e96f82b3a0ed97ffab.
This patch came on top of another patch that introduced a regression.
Revert it before addressing the culprit.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
|
|
This reverts commit d18fddff061d2796525e6d4a958cb3d30aed8efd.
This patch came on top of another patch that introduced a regression.
Revert it before addressing the culprit.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
|
|
'PTR_ERR(p) == -E*' is a stronger condition than IS_ERR(p).
Hence, IS_ERR(p) is unneeded.
The semantic patch that generates this commit is as follows:
// <smpl>
@@
expression ptr;
constant error_code;
@@
-IS_ERR(ptr) && (PTR_ERR(ptr) == - error_code)
+PTR_ERR(ptr) == - error_code
// </smpl>
Link: http://lkml.kernel.org/r/20200106045833.1725-1-masahiroy@kernel.org
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Stephen Boyd <sboyd@kernel.org> [drivers/clk/clk.c]
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> [GPIO]
Acked-by: Wolfram Sang <wsa@the-dreams.de> [drivers/i2c]
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> [acpi/scan.c]
Acked-by: Rob Herring <robh@kernel.org>
Cc: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for ROHM BD71828 PMICs and GPIOs
- Add support for Qualcomm Aqstic Audio Codecs WCD9340 and WCD9341
New Device Support:
- Add support for BD71828 to BD70528 RTC driver
- Add support for Intel's Jasper Lake to LPSS PCI
New Functionality:
- Add support for Power Key to ROHM BD71828
- Add support for Clocks to ROHM BD71828
- Add support for GPIOs to Dialog DA9062
- Add support for USB PD Notify to ChromiumOS EC
- Allow callers to specify args when requesting regmap lookup; syscon
Fix-ups:
- Improve error handling and sanity checking; atmel-hlcdc, dln2
- Device Tree support/documentation; bd71828, da9062, xylon,logicvc,
ab8500, max14577, atmel-usart
- Match devices using platform IDs; bd7xxxx
- Refactor BD718x7 regulator component; bd718x7-regulator
- Use standard interfaces/helpers; syscon, sm501
- Trivial (whitespace, spelling, etc); ab8500-core, Kconfig
- Remove unused code; db8500-prcmu, tqmx86
- Wait until boot has finished before accessing registers;
madera-core
- Provide missing register value defaults; cs47l15-tables
- Allow more time for hardware to reset; madera-core
Bug Fixes:
- Fix erroneous register values; rohm-bd70528
- Fix register volatility; axp20x, rn5t618
- Fix Kconfig dependencies; MFD_MAX77650
- Fix incorrect compatible string; da9062-core
- Fix syscon_regmap_lookup_by_phandle_args() stub; syscon"
* tag 'mfd-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (41 commits)
mfd: syscon: Fix syscon_regmap_lookup_by_phandle_args() dummy
mfd: wcd934x: Add support to wcd9340/wcd9341 codec
mfd: syscon: Add arguments support for syscon reference
mfd: rn5t618: Mark ADC control register volatile
dt-bindings: atmel-usart: Add microchip,sam9x60-{usart, dbgu}
dt-bindings: atmel-usart: Remove wildcard
mfd: cros_ec: Add cros-usbpd-notify subdevice
mfd: da9062: Fix watchdog compatible string
mfd: madera: Allow more time for hardware reset
mfd: cs47l15: Add missing register default
mfd: madera: Wait for boot done before accessing any other registers
mfd: Kconfig: Rename Samsung to lowercase
mfd: tqmx86: remove set but not used variable 'i2c_ien'
mfd: dbx500-prcmu: Drop DSI pll clock functions
mfd: dbx500-prcmu: Drop set_display_clocks()
mfd: max77650: Select REGMAP_IRQ in Kconfig
mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile
mfd: ab8500: Fix ab8500-clk typo
mfd: intel-lpss: Add Intel Jasper Lake PCI IDs
dt-bindings: mfd: max14577: Add reference to max14040_battery.txt descriptions
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes, nothing too exciting about
this.
Some changes hit arch/sh and arch/arm but are well isolated and
acknowledged by the respective arch maintainers.
Core changes:
- Dropped the chained IRQ setup callback into GPIOLIB as we got rid
of the last users of that in this changeset.
New drivers:
- New driver for Ingenic X1830.
- New driver for Freescale i.MX8MP.
Driver enhancements:
- Fix all remaining Intel drivers to pass their IRQ chips along with
the GPIO chips.
- Intel Baytrail allocates its irqchip dynamically.
- Intel Lynxpoint is thoroughly rewritten and modernized.
- Aspeed AST2600 pin muxing and configuration is much improved.
- Qualcomm SC7180 functions are updated and wakeup interrupt map is
provided.
- A whole slew of Renesas SH-PFC cleanups and improvements.
- Fix up the Intel DT bindings to use the generic YAML DT bindings
schema (a first user of this)"
* tag 'pinctrl-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
pinctrl: madera: Remove extra blank line
pinctrl: qcom: Don't lock around irq_set_irq_wake()
pinctrl: mvebu: armada-37xx: use use platform api
gpio: Drop the chained IRQ handler assign function
pinctrl: freescale: Add i.MX8MP pinctrl driver support
dt-bindings: imx: Add pinctrl binding doc for i.MX8MP
pinctrl: tigerlake: Tiger Lake uses _HID enumeration
pinctrl: sunrisepoint: Add Coffee Lake-S ACPI ID
pinctrl: iproc: Use platform_get_irq_optional() to avoid error message
pinctrl: dt-bindings: Fix some errors in the lgm and pinmux schema
pinctrl: intel: Pass irqchip when adding gpiochip
pinctrl: intel: Add GPIO <-> pin mapping ranges via callback
pinctrl: baytrail: Replace WARN with dev_info_once when setting direct-irq pin to output
pinctrl: baytrail: Do not clear IRQ flags on direct-irq enabled pins
pinctrl: sunrisepoint: Add missing Interrupt Status register offset
pinctrl: sh-pfc: Split R-Car H3 support in two independent drivers
pinctrl: artpec6: fix __iomem on reg in set
pinctrl: ingenic: Use devm_platform_ioremap_resource()
pinctrl: ingenic: Factorize irq_set_type function
pinctrl: ingenic: Remove duplicated ingenic_chip_info structures
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.6 kernel cycle.
This is a pretty calm cycle so far, nothing special going on really.
Some more changes will come in from the irqchip and pin control trees.
I also deleted an orphan include file for FMC that was dangling since
subsystem was removed.
Core changes:
- Document the usecases for the kernelspace vs userspace handling of
GPIOs.
- Handle MSI (message signalled interrupts) properly in the core
hierarchical irqdomain code.
- Fix a rare race condition while initializing the descriptor array.
New drivers:
- Xylon LogiCVC GPIO driver.
- WDC934x GPIO controller driver.
Driver improvements:
- Implemented suspend/resume in the Tegra driver.
- MPC8xx edge detection fixup.
- Properly convert ThunderX to use hierarchical irqdomain with
GPIOLIB_IRQCHIP on top of the revert of the previous buggy
switchover. This time it works (hopefully).
Misc:
- Drop a FMC remnant file <linux/ipmi-fru.h>
- A slew of fixes"
* tag 'gpio-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (48 commits)
MAINTAINERS: Replace Tien Hock Loh as Altera PIO maintainer
gpiolib: hold gpio devices lock until ->descs array is initialised
gpio: aspeed-sgpio: fixed typos
gpio: mvebu: clear irq in edge cause register before unmask edge irq
gpiolib: Lower verbosity when allocating hierarchy irq
gpiolib: Remove duplicated function gpio_do_set_config()
gpio: Fix the no return statement warning
gpio: wcd934x: Add support to wcd934x gpio controller
gpiolib: remove set but not used variable 'config'
gpio: vx855: fixed a typo
gpio: mockup: sort headers alphabetically
gpio: mockup: update the license tag
gpio: Remove the unused flags
gpiolib: Set lockdep class for hierarchical irq domains
gpio: thunderx: Switch to GPIOLIB_IRQCHIP
gpiolib: Add the support for the msi parent domain
gpiolib: Add support for the irqdomain which doesn't use irq_fwspec as arg
gpio: Add use guidance documentation
dt-bindings: gpio: wcd934x: Add bindings for gpio
gpio: altera: change to platform_get_irq_optional to avoid false-positive error
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The interrupt departement provides:
- A mechanism to shield isolated tasks from managed interrupts:
The affinity of managed interrupts is completely controlled by the
kernel and user space has no influence on them. The reason is that
the automatically assigned affinity correlates to the multi-queue
CPU handling of block devices.
If the generated affinity mask spaws both housekeeping and isolated
CPUs the interrupt could be routed to an isolated CPU which would
then be disturbed by I/O submitted by a housekeeping CPU.
The new mechamism ensures that as long as one housekeeping CPU is
online in the assigned affinity mask the interrupt is routed to a
housekeeping CPU.
If there is no online housekeeping CPU in the affinity mask, then
the interrupt is routed to an isolated CPU to keep the device queue
intact, but unless the isolated CPU submits I/O by itself these
interrupts are not raised.
- A small addon to the device tree irqdomain core code to avoid
duplication in irq chip drivers
- Conversion of the SiFive PLIC to hierarchical domains
- The usual pile of new irq chip drivers: SiFive GPIO, Aspeed SCI,
NXP INTMUX, Meson A1 GPIO
- The first cut of support for the new ARM GICv4.1
- The usual pile of fixes and improvements in core and driver code"
* tag 'irq-core-2020-01-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (33 commits)
genirq, sched/isolation: Isolate from handling managed interrupts
irqchip/gic-v4.1: Allow direct invalidation of VLPIs
irqchip/gic-v4.1: Suppress per-VLPI doorbell
irqchip/gic-v4.1: Add VPE INVALL callback
irqchip/gic-v4.1: Add VPE eviction callback
irqchip/gic-v4.1: Add VPE residency callback
irqchip/gic-v4.1: Add mask/unmask doorbell callbacks
irqchip/gic-v4.1: Plumb skeletal VPE irqchip
irqchip/gic-v4.1: Implement the v4.1 flavour of VMOVP
irqchip/gic-v4.1: Don't use the VPE proxy if RVPEID is set
irqchip/gic-v4.1: Implement the v4.1 flavour of VMAPP
irqchip/gic-v4.1: VPE table (aka GICR_VPROPBASER) allocation
irqchip/gic-v3: Add GICv4.1 VPEID size discovery
irqchip/gic-v3: Detect GICv4.1 supporting RVPEID
irqchip/gic-v3-its: Fix get_vlpi_map() breakage with doorbells
irqdomain: Fix a memory leak in irq_domain_push_irq()
irqchip: Add NXP INTMUX interrupt multiplexer support
dt-bindings: interrupt-controller: Add binding for NXP INTMUX interrupt multiplexer
irqchip: Define EXYNOS_IRQ_COMBINER
irqchip/meson-gpio: Add support for meson a1 SoCs
...
|
|
Pull MMC updates from Ulf Hansson:
"There are no updates for the MEMSTICK subsystem this time. But note
that I am also carrying a patch from the pinctrl tree, which has been
shared through an immutable branch.
Summary:
MMC core:
- Convert to reasonable timeouts for all CMD6 commands (updates for
BKOPS, CACHE_FLUSH and INAND_CMD38_ARG_EXT_CSD) for eMMC
- Respect f_max clock rate at card initialization
- Add gpiod_toggle_active_low() API
- Consolidate slot-gpio code by using gpiod_toggle_active_low()
MMC host:
- Add pinctrl_select_default_state() API
- Consolidate pintctrl code by using pinctrl_select_default_state()
- mmci: Support any block sizes for SDIO for some variants
- mmci: Enable reset control for stm32_sdmmc
- mmc_spi: Toggle SPI_CS_HIGH polarity rather than hard-coding it
- renesas_sdhi: Add support for the r8a77961 variant
- renesas_sdhi: A few minor improvements
- rockchip-dw-mshc: Add support for the rk3308 variant
- sdhci: Enable support for external DMA controllers
- sdhci: Fixup error path when sending CMD12
- sdhci-brcmstb: Add support for 7216b0 variant
- sdhci-brcmstb: Add support for command queuing (CQHCI)
- sdhci-brcmstb: Add support for eMMC HS400ES mode
- sdhci-msm: Add support for the sc7180 variant
- sdhci-msm: Add support for command queuing (CQHCI)
- sdhci-of-at91: Add support for the SAM9x60 variant
- sdhci-of-at91: Improve support for tunings
- sdhci-of-esdhc: A few fixups for some clock related issues
- sdhci-omap: Add support for the am335x and the am437x variants
- sdhci-omap: Improve support for erase operations
- sdhci-omap: Add support for external DMA"
* tag 'mmc-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (89 commits)
mmc: core: Default to generic_cmd6_time as timeout in __mmc_switch()
mmc: block: Use generic_cmd6_time when modifying INAND_CMD38_ARG_EXT_CSD
mmc: core: Specify timeouts for BKOPS and CACHE_FLUSH for eMMC
mmc: sdhci-cadence: remove unneeded 'inline' marker
dt-bindings: mmc: rockchip-dw-mshc: add description for rk3308
dt-bindings: mmc: convert rockchip dw-mshc bindings to yaml
dt-bindings: mmc: convert synopsys dw-mshc bindings to yaml
mmc: sdhci-msm: Add CQHCI support for sdhci-msm
mmc: sdhci: Let a vendor driver supply and update ADMA descriptor size
mmc: sdhci-of-esdhc: fix serious issue clock is always disabled
mmc: sdhci-of-esdhc: fix transfer mode register reading
mmc: sdhci-brcmstb: Fix incorrect switch to HS mode
mmc: sdhci-brcmstb: Add support for Command Queuing (CQE)
mmc: sdhci-brcmstb: Add shutdown callback
mmc: sdhci-brcmstb: Fix driver to defer on clk_get defer
mmc: sdhci-brcmstb: Add ability to use HS400ES transfer mode
dt-bindings: mmc: brcm,sdhci-brcmstb: Add support for 7216b0
mmc: core: limit probe clock frequency to configured f_max
mmc: sdhci-milbeaut: Remove redundant platform_get_irq error message
mmc: sdhci: fix an issue of mixing different types
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio: updates for v5.6
- use platform_get_irq_optional() in gpio-altera
|
|
ROHM BD71828 PMIC contains 4 pins which can be configured by OTP
to be used for general purposes. First 3 can be used as outputs
and 4.th pin can be used as input. Allow them to be controlled
via GPIO framework.
The driver assumes all of the pins are configured as GPIOs and
trusts that the reserved pins in other OTP configurations are
excluded from control using "gpio-reserved-ranges" device tree
property (or left untouched by GPIO users).
Typical use for 4.th pin (input) is to use it as HALL sensor
input so that this pin state is toggled when HALL sensor detects
LID position change (from close to open or open to close). PMIC
HW implements some extra logic which allows PMIC to power-up the
system when this pin is toggled. Please see the data sheet for
details of GPIO options which can be selected by OTP settings.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
If a driver consuming the GPIO chip is being probed at the same time as
the GPIO driver is registering the chip, it is possible for the
consuming driver to see the ->descs array in an uninitialised state.
For example, the gpio-keys-polled driver can fail like this:
kernel: gpiod_request: invalid GPIO (no device)
kernel: gpio-keys-polled PRP0001:07: failed to get gpio: -22
kernel: gpio-keys-polled: probe of PRP0001:07 failed with error -22
This patch makes gpiochip_add() hold the lock protecting gpio_devices
until it has finished setting desc->gdev on the newly inserted list
entry.
Signed-off-by: Dan Callaghan <dan.callaghan@opengear.com>
Link: https://lore.kernel.org/r/20200121001216.15964-1-dan.callaghan@opengear.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This fixes some various typos.
Signed-off-by: Sachin Agarwal <asachin591@gmail.com>
Link: https://lore.kernel.org/r/20200118105319.68637-1-sachinagarwal@sachins-MacBook-2.local
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
gpiochip_set_chained_irqchip() would assign a chained handler
to a GPIO chip. We now populate struct gpio_irq_chip for all
chained GPIO irqchips so drop this function.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200113220800.77817-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When input GPIO set from 0 to 1, the interrupt bit asserted in the GPIO
Interrupt Cause Register (ICR) even if the corresponding interrupt
masked in the GPIO Interrupt Mask Register.
Because interrupt mask register only affects assertion of the interrupt
bits in Main Interrupt Cause Register and it does not affect the
setting of bits in the GPIO ICR.
So, there is problem, when we unmask interrupt with already
asserted bit in the GPIO ICR, then false interrupt immediately occurs
even if GPIO don't change their value since last unmask.
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20200115073811.24438-1-bigunclemax@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In the current codes, the following 3 lines would be output to
the console for each irq line.
gpio gpiochip0: (gpio_thunderx): allocate IRQ 10, hwirq 0
gpio gpiochip0: (gpio_thunderx): found parent hwirq 245784
gpio gpiochip0: (gpio_thunderx): alloc_irqs_parent for 10 parent hwirq 245784
In general, there are about tens of irq lines for each gpio chip,
and then it would emit so many insignificant log in the boot process.
These infos are more suitable for the dbg purpose. So change these
to the dbg level. With this change, about 200 lines are suppressed
on my Marvell cn96xx board.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://lore.kernel.org/r/20200120095625.25164-1-haokexin@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v5.6-1
* Tiger Lake appears to have _HID enumeration, thus driver has been updated
* Coffee Lake-S has the same IP as Sunrisepoint, thus ID has been added
* Baytrail has got more clean ups and bug fixes, such as direct IRQ handling
* Lynxpoint GPIO has been converted to true pin control driver
* The common driver now uses IRQ chip enumeration via GPIO chip
The following is an automated git shortlog grouped by driver:
baytrail:
- Replace WARN with dev_info_once when setting direct-irq pin to output
- Do not clear IRQ flags on direct-irq enabled pins
- Reuse struct intel_pinctrl in the driver
- Use local variable to keep device pointer
- Keep pointer to struct device instead of its container
- Use GPIO direction definitions
- Move IRQ valid mask initialization to a dedicated callback
- Group GPIO IRQ chip initialization
- Allocate IRQ chip dynamic
cherryview:
- Use GPIO direction definitions
intel:
- Pass irqchip when adding gpiochip
- Add GPIO <-> pin mapping ranges via callback
- Share struct intel_pinctrl for wider use
- Use GPIO direction definitions
lynxpoint:
- Update summary in the driver
- Switch to pin control API
- Add GPIO <-> pin mapping ranges via callback
- Implement ->pin_dbg_show()
- Add pin control operations
- Reuse struct intel_pinctrl in the driver
- Add pin control data structures
- Implement intel_gpio_get_direction callback
- Implement ->irq_ack() callback
- Move ownership check to IRQ chip
- Move lp_irq_type() closer to IRQ related routines
- Move ->remove closer to ->probe()
- Extract lp_gpio_acpi_use() for future use
- Convert unsigned to unsigned int
- Switch to memory mapped IO accessors
- Keep pointer to struct device instead of its container
- Relax GPIO request rules
- Assume 2 bits for mode selector
- Use standard pattern for memory allocation
- Use %pR to print IO resource
- Drop useless assignment
- Correct amount of pins
- Use raw_spinlock for locking
- Move GPIO driver to pin controller folder
sunrisepoint:
- Add Coffee Lake-S ACPI ID
- Add missing Interrupt Status register offset
tigerlake:
- Tiger Lake uses _HID enumeration
|
|
Adds the GPIO driver for SiFive RISC-V SoCs.
Signed-off-by: Wesley W. Terpstra <wesley@sifive.com>
[Atish: Various fixes and code cleanup]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1575976274-13487-6-git-send-email-yash.shah@sifive.com
|
|
gpio_set_config() simply call gpio_do_set_config(),
so remove the duplicated function.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200116142927.58908-1-yuehaibing@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
Linux 5.5-rc6
|
|
This patch adds support to wcd934x gpio block found in
WCD9340/WC9341 Audio codecs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200107130844.20763-3-srinivas.kandagatla@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
drivers/gpio/gpiolib.c: In function gpio_set_config:
drivers/gpio/gpiolib.c:3053:16: warning:
variable config set but not used [-Wunused-but-set-variable]
commit d90f36851d65 ("gpiolib: have a single place
of calling set_config()") left behind this unused variable.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200108121117.45060-1-yuehaibing@huawei.com
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
we had written "betwee" rather than "between".
Signed-off-by: Sachin agarwal <asachin591@gmail.com>
Link: https://lore.kernel.org/r/20200112143312.66048-1-sachinagarwal@sachins-MacBook-2.local
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For consistency and easier maintenance: sort the headers alphabetically.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200114150253.28716-3-brgl@bgdev.pl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The current GPL v2.0 or later SPDX tag is 'GPL-2.0-or-later' as defined
at https://spdx.org/licenses/.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200114150253.28716-2-brgl@bgdev.pl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
drivers/gpio/gpio-grgpio.c: In function ‘grgpio_remove’:
drivers/gpio/gpio-grgpio.c:438:16: warning: unused variable ‘flags’ [-Wunused-variable]
unsigned long flags;
^
Fixes: 25d071b3f6db ("gpio: gpio-grgpio: fix possible sleep-in-atomic-context bugs in grgpio_remove()")
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Link: https://lore.kernel.org/r/1579009062-7154-1-git-send-email-zhangshaokun@hisilicon.com
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com
Reviewed-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
I see the following lockdep splat in the qcom pinctrl driver when
attempting to suspend the device.
============================================
WARNING: possible recursive locking detected
5.4.2 #2 Tainted: G S
--------------------------------------------
cat/6536 is trying to acquire lock:
ffffff814787ccc0 (&irq_desc_lock_class){-.-.}, at: __irq_get_desc_lock+0x64/0x94
but task is already holding lock:
ffffff81436740c0 (&irq_desc_lock_class){-.-.}, at: __irq_get_desc_lock+0x64/0x94
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&irq_desc_lock_class);
lock(&irq_desc_lock_class);
*** DEADLOCK ***
May be due to missing lock nesting notation
7 locks held by cat/6536:
#0: ffffff8140e0c420 (sb_writers#7){.+.+}, at: vfs_write+0xc8/0x19c
#1: ffffff8121eec480 (&of->mutex){+.+.}, at: kernfs_fop_write+0x128/0x1f4
#2: ffffff8147cad668 (kn->count#263){.+.+}, at: kernfs_fop_write+0x130/0x1f4
#3: ffffffd011446000 (system_transition_mutex){+.+.}, at: pm_suspend+0x108/0x354
#4: ffffff814302b970 (&dev->mutex){....}, at: __device_suspend+0x16c/0x420
#5: ffffff81436740c0 (&irq_desc_lock_class){-.-.}, at: __irq_get_desc_lock+0x64/0x94
#6: ffffff81479b8c10 (&pctrl->lock){....}, at: msm_gpio_irq_set_wake+0x48/0x7c
stack backtrace:
CPU: 4 PID: 6536 Comm: cat Tainted: G S 5.4.2 #2
Call trace:
dump_backtrace+0x0/0x174
show_stack+0x20/0x2c
dump_stack+0xdc/0x144
__lock_acquire+0x52c/0x2268
lock_acquire+0x1dc/0x220
_raw_spin_lock_irqsave+0x64/0x80
__irq_get_desc_lock+0x64/0x94
irq_set_irq_wake+0x40/0x144
msm_gpio_irq_set_wake+0x5c/0x7c
set_irq_wake_real+0x40/0x5c
irq_set_irq_wake+0x70/0x144
cros_ec_rtc_suspend+0x38/0x4c
platform_pm_suspend+0x34/0x60
dpm_run_callback+0x64/0xcc
__device_suspend+0x314/0x420
dpm_suspend+0xf8/0x298
dpm_suspend_start+0x84/0xb4
suspend_devices_and_enter+0xbc/0x628
pm_suspend+0x214/0x354
state_store+0xb0/0x108
kobj_attr_store+0x14/0x24
sysfs_kf_write+0x4c/0x64
kernfs_fop_write+0x158/0x1f4
__vfs_write+0x54/0x18c
vfs_write+0xdc/0x19c
ksys_write+0x7c/0xe4
__arm64_sys_write+0x20/0x2c
el0_svc_common+0xa8/0x160
el0_svc_compat_handler+0x2c/0x38
el0_svc_compat+0x8/0x10
This is because the msm_gpio_irq_set_wake() function calls
irq_set_irq_wake() as a backup in case the irq comes in during the path
to idle. Given that we're calling irqchip functions from within an
irqchip we need to set the lockdep class to be different for this child
controller vs. the default one that the parent irqchip gets.
This used to be done before this driver was converted to hierarchical
irq domains in commit e35a6ae0eb3a ("pinctrl/msm: Setup GPIO chip in
hierarchy") via the gpiochip_irq_map() function. With hierarchical irq
domains this function has been replaced by
gpiochip_hierarchy_irq_domain_alloc(). Therefore, set the lockdep class
like was done previously in the irq domain path so we can avoid this
lockdep warning.
Fixes: fdd61a013a24 ("gpio: Add support for hierarchical IRQ domains")
Cc: Thierry Reding <treding@nvidia.com>
Cc: Brian Masney <masneyb@onstation.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200114231103.85641-1-swboyd@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The main parts of this patch are from commit a7fc89f9d5fc ("gpio:
thunderx: Switch to GPIOLIB_IRQCHIP") and patch [1]. And also adjust
thunderx_gpio_child_to_parent_hwirq() and add
thunderx_gpio_populate_parent_alloc_info() to make sure that
the correct hwirq are passed to the parent msi irqdomain.
[1] https://patchwork.ozlabs.org/patch/1210180/
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://lore.kernel.org/r/20200114082821.14015-5-haokexin@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If the gpio's parent irqdomain is a msi irqdomain, we should ignore
the EEXIST error returned by the msi irqdomain because all the msi
interrupts have already been allocated.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://lore.kernel.org/r/20200114082821.14015-4-haokexin@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some gpio's parent irqdomain may not use the struct irq_fwspec as
argument, such as msi irqdomain. So rename the callback
populate_parent_fwspec() to populate_parent_alloc_arg() and make it
allocate and populate the specific struct which is needed by the
parent irqdomain.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://lore.kernel.org/r/20200114082821.14015-3-haokexin@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This reverts commit a7fc89f9d5fcc10a5474cfe555f5a9e5df8b0f1f because
there are some bugs in this commit, and we don't have a simple way to
fix these bugs. So revert this commit to make the thunderx gpio work
on the stable kernel at least. We will switch to GPIOLIB_IRQCHIP
for thunderx gpio by following patches.
Fixes: a7fc89f9d5fc ("gpio: thunderx: Switch to GPIOLIB_IRQCHIP")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://lore.kernel.org/r/20200114082821.14015-2-haokexin@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch switches to platform_get_irq_optional() from
platform_get_irq() as it causes a false-positive error such as 'IRQ
index 0 not found' when IRQ is not used. The IRQ usage is optional in
this gpio-altera driver, so the error log is undesirable.
Signed-off-by: Ooi, Joyce <joyce.ooi@intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Drop the completed item: hierarchical irqchip helpers. Add
motivation for gpio descriptor refactoring. Extend the list of
stuff to do. Minor fixups.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200107212432.27587-1-linus.walleij@linaro.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio updates for v5.6
- improvements in the gpio-pca953x driver
- use platform_irq_count() in gpio-mvebu and gpio-bcm-kona
- remove unneeded MODULE_VERSION() usage in the gpio directory
- irq-related improvements in gpio-tegra driver
- several improvements for the core subsystem code: fix confusing indentation,
fix int type casting, unduplicate code in several places
|
|
On these boards, the irq_set_type must point one valid function pointer
that can correctly set both edge and falling edge.
Signed-off-by: Song Hui <hui.song_1@nxp.com>
Link: https://lore.kernel.org/r/20191122061839.24904-1-hui.song_1@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
grgpio_irq_map/unmap()
The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
drivers/gpio/gpio-grgpio.c, 261:
request_irq in grgpio_irq_map
drivers/gpio/gpio-grgpio.c, 255:
_raw_spin_lock_irqsave in grgpio_irq_map
drivers/gpio/gpio-grgpio.c, 318:
free_irq in grgpio_irq_unmap
drivers/gpio/gpio-grgpio.c, 299:
_raw_spin_lock_irqsave in grgpio_irq_unmap
request_irq() and free_irq() can sleep at runtime.
To fix these bugs, request_irq() and free_irq() are called without
holding the spinlock.
These bugs are found by a static analysis tool STCheck written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20191218132605.10594-1-baijiaju1990@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
drivers/gpio/gpiolib-sysfs.c, 796:
mutex_lock in gpiochip_sysfs_unregister
drivers/gpio/gpiolib.c, 1455:
gpiochip_sysfs_unregister in gpiochip_remove
drivers/gpio/gpio-grgpio.c, 460:
gpiochip_remove in grgpio_remove
drivers/gpio/gpio-grgpio.c, 449:
_raw_spin_lock_irqsave in grgpio_remove
kernel/irq/irqdomain.c, 243:
mutex_lock in irq_domain_remove
drivers/gpio/gpio-grgpio.c, 463:
irq_domain_remove in grgpio_remove
drivers/gpio/gpio-grgpio.c, 449:
_raw_spin_lock_irqsave in grgpio_remove
mutex_lock() can sleep at runtime.
To fix these bugs, the lock is dropped in grgpio_remove(), because there
is no need for locking in remove() callbacks.
These bugs are found by a static analysis tool STCheck written by
myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20191219131459.18640-1-baijiaju1990@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
On some laptops enabling wakeup on the GPIO interrupts used for ACPI _AEI
event handling causes spurious wakeups.
This commit adds a new honor_wakeup option, defaulting to true (our current
behavior), which can be used to disable wakeup on troublesome hardware
to avoid these spurious wakeups.
This is a workaround for an architectural problem with s2idle under Linux
where we do not have any mechanism to immediately go back to sleep after
wakeup events, other then for embedded-controller events using the standard
ACPI EC interface, for details see:
https://lore.kernel.org/linux-acpi/61450f9b-cbc6-0c09-8b3a-aff6bf9a0b3c@redhat.com/
One series of laptops which is not able to suspend without this workaround
is the HP x2 10 Cherry Trail models, this commit adds a DMI based quirk
which makes sets honor_wakeup to false on these models.
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200105160357.97154-3-hdegoede@redhat.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Turn the existing run_edge_events_on_boot_blacklist dmi_system_id table
into a generic quirk table, storing the quirks in the driver_data ptr.
This is a preparation patch for adding other types of (DMI based) quirks.
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200105160357.97154-2-hdegoede@redhat.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Unduplicate the offset check by simply calling gpiochip_get_desc() and
checking its return value.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Unduplicate the ngpio check by simply calling gpiochip_get_desc() and
checking its return value.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Unduplicate the ngpio check by simply calling gpiochip_get_desc() and
checking its return value.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
gpiochip_get_desc() takes a u16 hwnum, but it turns out most users don't
respect that and usually pass an unsigned int. Since implicit casting to
a smaller type is dangerous - let's change the type of hwnum to unsigned
int in gpiochip_get_desc() and in gpiochip_request_own_desc() where the
size of hwnum is not respected either and who's a user of the former.
This is safe as we then check the hwnum against the number of lines
before proceeding in gpiochip_get_desc().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Instead of calling the gpiochip's set_config() callback directly and
checking its existence every time - just add a new routine that performs
this check internally. Call it in gpio_set_config() and
gpiod_set_transitory(). Also call it in gpiod_set_debounce() and drop
the check for chip->set() as it's irrelevant to this config option.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Checkpatch complains about using 'unsigned' instead of 'unsigned int'.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
