| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.13 series.
Some administrativa:
I have a slew of 8250 serial patches and the new IOT2040 serial+GPIO
driver coming in through this tree, along with a whole bunch of Exar
8250 fixes. These are ACKed by Greg and also hit drivers/platform/*
where they are ACKed by Andy Shevchenko.
Speaking about drivers/platform/* there is also a bunch of ACPI stuff
coming through that route, again ACKed by Andy.
The MCP23S08 changes are coming in here as well. You already have the
commits in your tree, so this is just a result of sharing an immutable
branch between pin control and GPIO.
Core:
- Export add/remove for lookup tables so that modules can export GPIO
descriptor tables.
- Handle GPIO sleep states: it is now possible to flag that a GPIO
line may loose its state during suspend/resume of the system to
save power. This is used in the Wolfson Micro Arizona driver.
- ACPI-based GPIO was tightened up a lot around the edges.
- Use bitmap_fill() to speed up a loop.
New drivers:
- Exar XRA1403 SPI-based GPIO.
- MVEBU driver now supports Armada 7K and 8K.
- LP87565 PMIC GPIO.
- Renesas R-CAR R8A7743 (RZ/G1M).
- The new IOT2040 8250 serial/GPIO also comes in through this
changeset.
Substantial driver changes:
- Seriously fix the Exar 8250 GPIO portions to work.
- The MCP23S08 was moved out to a pin control driver.
- Convert MEVEBU to use regmap for register access.
- Drop Vulcan support from the Broadcom driver.
- Serious cleanup and improvement of the mockup driver, giving us a
better test coverage.
Misc:
- Lots of janitorial clean up.
- A bunch of documentation fixes"
* tag 'gpio-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (70 commits)
serial: exar: Add support for IOT2040 device
gpio-exar/8250-exar: Make set of exported GPIOs configurable
platform: Accept const properties
serial: exar: Factor out platform hooks
gpio-exar/8250-exar: Rearrange gpiochip parenthood
gpio: exar: Fix iomap request
gpio-exar/8250-exar: Do not even instantiate a GPIO device for Commtech cards
serial: uapi: Add support for bus termination
gpio: rcar: Add R8A7743 (RZ/G1M) support
gpio: gpio-wcove: Fix GPIO control register offset calculation
gpio: lp87565: Add support for GPIO
gpio: dwapb: fix missing first irq for edgeboth irq type
MAINTAINERS: Take maintainership for GPIO ACPI support
gpio: exar: Fix reading of directions and values
gpio: exar: Allocate resources on behalf of the platform device
gpio-exar/8250-exar: Fix passing in of parent PCI device
gpio: mockup: use devm_kcalloc() where applicable
gpio: mockup: add myself as author
gpio: mockup: improve the error message
gpio: mockup: don't return magic numbers from probe()
...
|
|
GPIOEVENT_REQUEST_BOTH_EDGES is not a single flag, but a binary OR of
GPIOEVENT_REQUEST_RISING_EDGE and GPIOEVENT_REQUEST_FALLING_EDGE.
The expression 'le->eflags & GPIOEVENT_REQUEST_BOTH_EDGES' we'll get
evaluated to true even if only one event type was requested.
Fix it by checking both RISING & FALLING flags explicitly.
Cc: stable@vger.kernel.org
Fixes: 61f922db7221 ("gpio: userspace ABI for reading GPIO line events")
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This was left behind by a cleanup patch:
drivers/gpio/gpiolib.c: In function 'gpiochip_irqchip_init_valid_mask':
drivers/gpio/gpiolib.c:1474:6: error: unused variable 'i' [-Werror=unused-variable]
Fixes: 923a654c186c ("gpiolib: Re-use bitmap_fill() instead of open coded loop")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Colin King <colin.king@canonical.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Re-use bitmap_fill() instead of open coded loop for setting an area of
bits in a bitmap.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This allows ACPI GPIO code to modify flags based on
ACPI GpioIo() / GpioInt() resources.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is preparatory patch for enabling GPIO ACPI to configure a pin
accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add new flags to allow users to specify that they are not concerned with
the status of GPIOs whilst in a sleep/low power state.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For hot-pluggable devices adding GPIOs dynamically we need to
assemble and add the gpio lookup tables at probe time in modules,
so that requesting these GPIOs in attached drivers can work.
Export lookup table functions for modules.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of new char/misc driver drivers and features for
4.12-rc1.
There's lots of new drivers added this time around, new firmware
drivers from Google, more auxdisplay drivers, extcon drivers, fpga
drivers, and a bunch of other driver updates. Nothing major, except if
you happen to have the hardware for these drivers, and then you will
be happy :)
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (136 commits)
firmware: google memconsole: Fix return value check in platform_memconsole_init()
firmware: Google VPD: Fix return value check in vpd_platform_init()
goldfish_pipe: fix build warning about using too much stack.
goldfish_pipe: An implementation of more parallel pipe
fpga fr br: update supported version numbers
fpga: region: release FPGA region reference in error path
fpga altera-hps2fpga: disable/unprepare clock on error in alt_fpga_bridge_probe()
mei: drop the TODO from samples
firmware: Google VPD sysfs driver
firmware: Google VPD: import lib_vpd source files
misc: lkdtm: Add volatile to intentional NULL pointer reference
eeprom: idt_89hpesx: Add OF device ID table
misc: ds1682: Add OF device ID table
misc: tsl2550: Add OF device ID table
w1: Remove unneeded use of assert() and remove w1_log.h
w1: Use kernel common min() implementation
uio_mf624: Align memory regions to page size and set correct offsets
uio_mf624: Refactor memory info initialization
uio: Allow handling of non page-aligned memory regions
hangcheck-timer: Fix typo in comment
...
|
|
Interrupt numbers are never negative, zero serves as the special invalid
value.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Currently, the GPIO interface is said to Open Drain if it is Single
Ended and active LOW. Similarly, it is said as Open Source if it is
Single Ended and active HIGH.
The active HIGH/LOW is used in the interface for setting the pin
state to HIGH or LOW when enabling/disabling the interface.
In Open Drain interface, pin is set to HIGH by putting pin in
high impedance and LOW by driving to the LOW.
In Open Source interface, pin is set to HIGH by driving pin to
HIGH and set to LOW by putting pin in high impedance.
With above, the Open Drain/Source is unrelated to the active LOW/HIGH
in interface. There is interface where the enable/disable of interface
is ether active LOW or HIGH but it is Open Drain type.
Hence decouple the Open Drain with Single Ended + Active LOW and
Open Source with Single Ended + Active HIGH.
Adding different flag for the Open Drain/Open Source which is valid
only when Single ended flag is enabled.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Replace the open coded registration of the cdev and dev with the
new device_add_cdev() helper. The helper replaces a common pattern by
taking the proper reference against the parent device and adding both
the cdev and the device.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's unusual to have error checking like (ret <= 0) in cases when
counting GPIO resources. In case when it's mandatory we propagate the
error (-ENOENT), otherwise we don't use the result.
This makes consistent behaviour across all possible variants called in
gpiod_count().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Remove extra 'l' in "successfull".
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.11 cycle
Core changes:
- Augment fwnode_get_named_gpiod() to configure the GPIO pin
immediately after requesting it like all other APIs do. This is a
treewide change also updating all users.
- Pass a GPIO label down to gpiod_request() from
fwnode_get_named_gpiod(). This makes debugfs and the userspace ABI
correctly reflect the current in-kernel consumer of a pin taken
using this abstraction. This is a treewide change also updating all
users.
- Rename devm_get_gpiod_from_child() to
devm_fwnode_get_gpiod_from_child() to reflect the fact that this
function is operating on a fwnode object. This is a treewide change
also updating all users.
- Make it possible to take multiple GPIOs in a single hog of device
tree hogs.
- The refactorings switching GPIO chips to use the .set_config()
callback using standard pin control properties and providing a
backend into the pin control subsystem that were also merged into
the pin control tree naturally appear here too.
Testing instrumentation:
- A whole slew of cleanups and improvements to the mockup GPIO
driver. We now have an extended userspace test exercising the
subsystem, and we can inject interrupts etc from userspace to fully
test the core GPIO functionality.
New drivers:
- New driver for the Cortina Systems Gemini GPIO controller.
- New driver for the Exar XR17V352/354/358 chips.
- New driver for the ACCES PCI-IDIO-16 PCI GPIO card.
Driver changes:
- RCAR: set the irqchip parent device, add fine-grained runtime PM
support.
- pca953x: support optional RESET control line on the chip.
- DaVinci: cleanups and simplifications. Add support for multiple
instances.
- .set_multiple() and naming of lines on more or less all of the
ISA/PCI GPIO controllers.
- mcp23s08: refactored to use regmap as a first step to further
rewrites and modernizations"
* tag 'gpio-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (61 commits)
gpio: reintroduce devm_get_gpiod_from_child()
gpio: pci-idio-16: Fix PCI BAR index
gpio: pci-idio-16: Fix PCI device ID code
gpio: mockup: implement event injecting over debugfs
gpio: mockup: add a dummy irqchip
gpio: mockup: implement naming the lines
gpio: mockup: code shrink
gpio: mockup: readability tweaks
gpio: Add GPIO support for the ACCES PCI-IDIO-16
gpio: Add the devm_fwnode_get_index_gpiod_from_child() helper
gpio: Rename devm_get_gpiod_from_child()
gpio: mcp23s08: Select REGMAP/REGMAP_I2C to fix build error
gpio: ws16c48: Add support for GPIO names
gpio: gpio-mm: Add support for GPIO names
gpio: 104-idio-16: Add support for GPIO names
gpio: 104-idi-48: Add support for GPIO names
gpio: 104-dio-48e: Add support for GPIO names
gpio: ws16c48: Remove unnecessary driver_data set
gpio: gpio-mm: Remove unnecessary driver_data set
gpio: 104-idio-16: Remove unnecessary driver_data set
...
|
|
|
|
devm_fwnode_get_gpiod_from_child() currently allows GPIO users to
request a GPIO that is defined in a child fwnode instead of directly in
the device fwnode.
Extend this API by adding the devm_fwnode_get_index_gpiod_from_child()
helper which does the same except you can also specify an index in case
the 'xx-gpios' property describe several GPIOs.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
"if (!x) WARN_ON(x)" can never trigger.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Linux 4.10-rc6
Resolved conflicts in:
drivers/pinctrl/pinctrl-amd.c
drivers/pinctrl/samsung/pinctrl-exynos.c
|
|
|
|
Currently we already have two pin configuration related callbacks
available for GPIO chips .set_single_ended() and .set_debounce(). In
future we expect to have even more, which does not scale well if we need
to add yet another callback to the GPIO chip structure for each possible
configuration parameter.
Better solution is to reuse what we already have available in the
generic pinconf.
To support this, we introduce a new .set_config() callback for GPIO
chips. The callback takes a single packed pin configuration value as
parameter. This can then be extended easily beyond what is currently
supported by just adding new types to the generic pinconf enum.
If the GPIO driver is backed up by a pinctrl driver the GPIO driver can
just assign gpiochip_generic_config() (introduced in this patch) to
.set_config and that will take care configuration requests are directed
to the pinctrl driver.
We then convert the existing drivers over .set_config() and finally
remove the .set_single_ended() and .set_debounce() callbacks.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
Currently all users of fwnode_get_named_gpiod() have no way to
specify a label for the GPIO. So GPIOs listed in debugfs are shown
with label "?". With this change a proper label is used.
Also adjust all users so they can pass a label, properly retrieved
from device tree properties.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Make fwnode_get_named_gpiod() consistent with the rest of
gpiod_get() like API, i.e. configure GPIO pin immediately after
request.
Besides obvious clean up it will help to configure pins based
on firmware provided resources.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The helper function for adding a GPIO chip compiles in a lockdep
key for debugging, the same key is needed for nested chips as
well.
The macro construction is unreadable, replace this with two
static inlines instead.
The _gpiochip_irqchip_add prefixed function is not helpful,
rename it with gpiochip_irqchip_add_key() that tell us what the
function is actually doing.
Fixes: d245b3f9bd36 ("gpio: simplify adding threaded interrupts")
Cc: Roger Quadros <rogerq@ti.com>
Reported-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reported-by: Roger Quadros <rogerq@ti.com>
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
container_of() does pointer math on the pointer that's passed in.
If it were to return a NULL pointer the value passed in would
need to be perfectly offset from 0 to make that so. Remove these
checks because they don't make sense.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The macro for_each_set_bit() effectively looks up to the next
set bit in array of bits.
Instead of open coding that switch to for_each_set_bit() in
gpio_chip_set_multiple().
While here, make gpio_chip_set_multiple() non-destructive
against its parameters. We are safe since all callers, i.e.
gpiod_set_array_value_complex(), handle that already.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When removing a gpiochip that uses GPIO hogging (e.g. by unloading the
chip's DT overlay), a warning is printed:
gpio gpiochip8: REMOVING GPIOCHIP WITH GPIOS STILL REQUESTED
This happens because gpiochip_free_hogs() is called after the gdev->chip
pointer is reset to NULL. Hence __gpiod_free() cannot determine the
chip in use, and cannot clear flags nor call the optional chip-specific
.free() callback.
Move the call to gpiochip_free_hogs() up to fix this.
Cc: stable@vger.kernel.org
Fixes: ff2b135922992756 ("gpio: make the gpiochip a real device")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Luinus Walleij:
"Bulk GPIO changes for the v4.10 kernel cycle:
Core changes:
- Simplify threaded interrupt handling: instead of passing numbed
parameters to gpiochip_irqchip_add_chained() we create a new call:
gpiochip_irqchip_add_nested() so the two types are clearly
semantically different. Also make sure that all nested chips call
gpiochip_set_nested_irqchip() which is necessary for IRQ resend to
work properly if it happens.
- Return error on seek operations for the chardev.
- Clamp values set as part of gpio[d]_direction_output() so that
anything != 0 will be send down to the driver as "1" not the value
passed in.
- ACPI can now support naming of GPIO lines, hogs and holes in the
GPIO lists.
New drivers:
- The SX150x driver was deemed unfit for the GPIO subsystem and was
moved over to a combined GPIO+pinctrl driver in the pinctrl
subsystem.
New features:
- Various cleanups to various drivers"
* tag 'gpio-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (49 commits)
gpio: merrifield: Implement gpio_get_direction callback
gpio: merrifield: Add support for hardware debouncer
gpio: chardev: Return error for seek operations
gpio: arizona: Tidy up probe error path
gpio: arizona: Remove pointless set of platform drvdata
gpio: pl061: delete platform data handling
gpio: pl061: move platform data into driver
gpio: pl061: rename variable from chip to pl061
gpio: pl061: rename state container struct
gpio: pl061: use local state for parent IRQ storage
gpio: set explicit nesting on drivers
gpio: simplify adding threaded interrupts
gpio: vf610: use builtin_platform_driver
gpio: axp209: use correct register for GPIO input status
gpio: stmpe: fix interrupt handling bug
gpio: em: depnd on ARCH_SHMOBILE
gpio: zx: depend on ARCH_ZX
gpio: x86: update config dependencies for x86 specific hardware
gpio: mb86s7x: use builtin_platform_driver
gpio: etraxfs: use builtin_platform_driver
...
|
|
|
|
The GPIO chardev is used for management tasks (allocating line and event
handles) and does neither support read() nor write() operations. Hence it
does not make much sense to allow seek operations.
Currently the chardev uses noop_llseek() for its seek implementation. This
function does not move the pointer and simply returns the current position
(always 0 for the GPIO chardev). noop_llseek() is primarily meant for
devices that can not support seek, but where there might be a user that
depends on the seek() operation succeeding. For newly added devices that
can not support seek operations it is recommended to use no_llseek(), which
will return an error. For more information see commit 6038f373a3dc
("llseek: automatically add .llseek fop").
Unfortunately this was overlooked when the GPIO chardev ABI was introduced.
But it is highly unlikely that since then userspace applications have
appeared that rely on being able to perform non-failing seek operations on
a GPIO chardev file descriptor. So it should be safe to change from
noop_llseel() to no_seek(). Also use nonseekable_open() in the chardev
open() callback to clear the FMODE_SEEK, FMODE_PREAD and FMODE_PWRITE flags
from the file. Neither of these should be set on a file that does not
support seek operations.
Cc: stable@vger.kernel.org
Fixes: 3c702e9987e2 ("gpio: add a userspace chardev ABI for GPIOs")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This tries to simplify the use of CONFIG_GPIOLIB_IRQCHIP when
using threaded interrupts: add a new call
gpiochip_irqchip_add_nested() to indicate that we're dealing
with a nested rather than a chained irqchip, then create a
separate gpiochip_set_nested_irqchip() to mirror
the gpiochip_set_chained_irqchip() call to connect the
parent and child interrupts.
In the nested case gpiochip_set_nested_irqchip() does nothing
more than call irq_set_parent() on each valid child interrupt,
which has little semantic effect in the kernel, but this is
probably still formally correct.
Update all drivers using nested interrupts to use
gpiochip_irqchip_add_nested() so we can now see clearly
which these users are.
The DLN2 driver can drop its specific hack with
.irq_not_threaded as we now recognize whether a chip is
threaded or not from its use of gpiochip_irqchip_add_nested()
signature rather than from inspecting .can_sleep.
We rename the .irq_parent to .irq_chained_parent since this
parent IRQ is only really kept around for the chained
interrupt handlers.
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Daniel Baluta <daniel.baluta@intel.com>
Cc: Bin Gao <bin.gao@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ajay Thomas <ajay.thomas.david.rajamanickam@intel.com>
Cc: Semen Protsenko <semen.protsenko@globallogic.com>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Phil Reid <preid@electromag.com.au>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When a GPIO line is marked as used for an interrupt, it is
helpful to set the label to "interrupt" so we know what is
going on when inspecting the lines.
If a GPIO is already properly named by gpiod_get*() we don't
need to do this. It only happens when a line is used from
the irqchip side of a GPIO driver without communicating
with the GPIO side, such as when gpiochip is used as interrupt
provider in the device tree.
If the line is still marked as used by "interrupt" when we
unmark it as used by an interrupt, also remove this label
from the descriptor.
Also shape up the code around unmarking IRQ lines.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
I saw weird values != [0,1] being passed down to drivers
in their .set_direction_output() callbacks. Go over the
gpiolib and make sure to hammer it to [0,1] before hitting
the driver to avoid undesired side effects.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When locking a GPIO line as IRQ, we go to lengths to
double-check that the line is really set as input before
marking it as used for IRQ. This is not good on GPIO chips
that can sleep, because this function is called in IRQ-safe
context. Just skip this if it can't be checked quickly.
Currently this happens on sleeping expanders such as STMPE
or TC3589x:
BUG: scheduling while atomic: swapper/1/0x00000002
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.9.0-rc1+ #38
Hardware name: Nomadik STn8815
[<c000f2e0>] (unwind_backtrace) from [<c000d244>] (show_stack+0x10/0x14)
[<c000d244>] (show_stack) from [<c0037b78>] (__schedule_bug+0x54/0x80)
[<c0037b78>] (__schedule_bug) from [<c042df14>] (__schedule+0x3a0/0x460)
[<c042df14>] (__schedule) from [<c042e028>] (schedule+0x54/0xb8)
(...)
This patch fixes that problem and relies on the direction
read from the chip when it was added.
Cc: stable@vger.kernel.org
Fixes: 9c10280d85c1 ("gpio: flush direction status in gpiochip_lock_as_irq()")
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When allocating a new line handle or event a file is allocated that it is
associated to. The file is attached to a file descriptor of the current
process and the file descriptor is returned to userspace using
copy_to_user(). If this copy operation fails the line handle or event
allocation is aborted, all acquired resources are freed and an error is
returned.
But the file struct is not freed and left attached to the userspace
application and even though the file descriptor number was not copied it is
trivial to guess. If a userspace application performs a IOCTL on such a
left over file descriptor it will trigger a use-after-free and if the file
descriptor is closed (latest when the application exits) a double-free is
triggered.
anon_inode_getfd() performs 3 tasks, allocate a file struct, allocate a
file descriptor for the current process and install the file struct in the
file descriptor. As soon as the file struct is installed in the file
descriptor it is accessible by userspace (even if the IOCTL itself hasn't
completed yet), this means uninstalling the fd on the error path is not an
option, since userspace might already got a reference to the file.
Instead anon_inode_getfd() needs to be broken into its individual steps.
The allocation of the file struct and file descriptor is done first, then
the copy_to_user() is executed and only if it succeeds the file is
installed.
Since the file struct is reference counted it can not be just freed, but
its reference needs to be dropped, which will also call the release()
callback, which will free the state attached to the file. So in this case
the normal error cleanup path should not be taken.
Cc: stable@vger.kernel.org
Fixes: d932cd49182f ("gpio: free handles in fringe cases")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIO_GET_LINEEVENT_IOCTL currently ignores unknown or undefined
linehandle and lineevent flags. From a backwards and forwards compatibility
viewpoint it is highly desirable to reject unknown flags though.
On one hand an application that is using newer flags and is running on
an older kernel has no way to detect if the new flags were handled
correctly if they are silently discarded.
On the other hand an application that (accidentally) passes undefined flags
will run fine on an older kernel, but may break on a newer kernel when
these flags get defined.
Ensure that requests that have undefined flags set are rejected with an
error, rather than silently discarding the undefined flags.
Cc: stable@vger.kernel.org
Fixes: 61f922db7221 ("gpio: userspace ABI for reading GPIO line events")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIO_GET_LINEHANDLE_IOCTL currently ignores unknown or undefined
linehandle flags. From a backwards and forwards compatibility viewpoint it
is highly desirable to reject unknown flags though.
On one hand an application that is using newer flags and is running on
an older kernel has no way to detect if the new flags were handled
correctly if they are silently discarded.
On the other hand an application that (accidentally) passes undefined flags
will run fine on an older kernel, but may break on a newer kernel when
these flags get defined.
Ensure that requests that have undefined flags set are rejected with an
error, rather than silently discarding the undefined flags.
Cc: stable@vger.kernel.org
Fixes: d7c51b47ac11 ("gpio: userspace ABI for reading/writing GPIO lines")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIOHANDLE_GET_LINE_VALUES_IOCTL handler allocates a gpiohandle_data
struct on the stack and then passes it to copy_to_user(). But depending on
the number of requested line handles the struct is only partially
initialized.
This exposes the previous, potentially sensitive, stack content to the
issuing userspace application. To avoid this make sure that the struct is
fully initialized.
Cc: stable@vger.kernel.org
Fixes: d7c51b47ac11 ("gpio: userspace ABI for reading/writing GPIO lines")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The line offset that is used as an index into the descs array is provided
by userspace and might go beyond the bounds of the array. If that happens
undefined behavior will occur.
Make sure that the offset is within the bounds of the desc array and reject
any requests that specify a value outside of it.
Cc: stable@vger.kernel.org
Fixes: 61f922db7221 ("gpio: userspace ABI for reading GPIO line events")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIOHANDLE_GET_LINE_VALUES_IOCTL handler allocates a gpiohandle_data
struct on the stack and then passes it to copy_to_user(). But only the
first element of the values array in the struct is set, which leaves the
struct partially initialized.
This exposes the previous, potentially sensitive, stack content to the
issuing userspace application. To avoid this make sure that the struct is
fully initialized.
Cc: stable@vger.kernel.org
Fixes: 61f922db7221 ("gpio: userspace ABI for reading GPIO line events")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The line offset that is used as an index into the descs array is provided
by userspace and might go beyond the bounds of the array. If that happens
undefined behavior will occur.
Make sure that the offset is within the bounds of the desc array and reject
any requests that specify a value outside of it.
Cc: stable@vger.kernel.org
Fixes: d7c51b47ac11 ("gpio: userspace ABI for reading/writing GPIO lines")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The GPIO_GET_CHIPINFO_IOCTL handler allocates a gpiochip_info struct on the
stack and then passes it to copy_to_user(). But depending on the length of
the GPIO chip name and label the struct is only partially initialized.
This exposes the previous, potentially sensitive, stack content to the
issuing userspace application. To avoid this make sure that the struct is
fully initialized.
Cc: stable@vger.kernel.org
Fixes: 521a2ad6f862 ("gpio: add userspace ABI for GPIO line information")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The current line offset validation is off by one. Depending on the data
stored behind the descs array this can either cause undefined behavior or
disclose arbitrary, potentially sensitive, memory to the issuing userspace
application.
Make sure that offset is within the bounds of the desc array.
Cc: stable@vger.kernel.org
Fixes: 521a2ad6f862 ("gpio: add userspace ABI for GPIO line information")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The generic GPIO library directly implement code for acpi_find_gpio()
which is only used with CONFIG_ACPI. This was probably done because
OF did the same thing, but I removed that so remove this too.
Rename the internal acpi_find_gpio() in gpiolib-acpi.c to
acpi_populate_gpio_lookup() which seems to be more appropriate anyway
so as to avoid a namespace clash with the same function.
Make the stub return -ENOENT rather than -ENOSYS (as that is for
syscalls!).
For some reason the sunxi pin control driver was including the private
gpiolib header, it works just fine without it so remove that oneliner.
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The generic GPIO library directly implement code for of_find_gpio()
which is only used with CONFIG_OF and causes compilation problems
on archs that do not even have stubs for OF functions, especially
on UM that does not implement any IO remap functions.
Move the function to gpiolib-of.c, implement a static inline stub
in gpiolib.h returning PTR_ERR(-ENOENT) if CONFIG_OF_GPIO is not
set and be done with it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
When using GPIO irqchip helpers to setup irqchip for a gpiolib based
driver, it is not possible to select which GPIOs to add to the IRQ domain.
Instead it just adds all GPIOs which is not always desired. For example
there might be GPIOs that for some reason cannot generated normal
interrupts at all.
To support this we add a flag irq_need_valid_mask to struct gpio_chip. When
this flag is set the core allocates irq_valid_mask that holds one bit for
each GPIO the chip has. By default all bits are set but drivers can
manipulate this using set_bit() and clear_bit() accordingly.
Then when gpiochip_irqchip_add() is called, this mask is checked and all
GPIOs with bit is set are added to the IRQ domain created for the GPIO
chip.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Follow DT and forbid default trigger if the GPIO irqchip device is
enumerated from ACPI. Triggering for these devices will be configured
automatically from ACPI interrupt resources provided by the BIOS.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Using a default trigger is a bad idea if using DT to configure
interrupts, as the device's interrupt specifier will always contain
the trigger configuration.
Let's warn about that particular situation, and revert to not
having a default. Hopefully, the couple of drivers still using
this feature will quickly be fixed.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
