| Age | Commit message (Collapse) | Author |
|---|
|
Linux 5.7-rc7
|
|
After the previous patch the two last parameters of
pca953x_recalc_addr() are unused and so can be dropped.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Some of the chips supported by the pca953x driver need the most
significant bit in the address word set to automatically increment the
address pointer on subsequent reads and writes (example: PCA9505). With
this bit unset the same register is read multiple times on a multi-byte
read sequence. Other chips must not have this bit set and autoincrement
always (example: PCA9555).
Up to now this AI bit was interpreted to be part of the address, which
resulted in inconsistent regmap caching when a register was written with
AI set and then read without it. This happened for the PCA9505 in
pca953x_gpio_set_multiple() where pca953x_read_regs() bulk read from the
cache for registers 0x8-0xc and then wrote to registers 0x88-0x8c. (Side
note: reading 5 values from offset 0x8 yiels OP0 5 times because AI must
be set to get OP0-OP4, which is another bug that is resolved here as a
by-product.) The same problem happens when calls to gpio_set_value() and
gpio_set_array_value() were mixed.
With this patch the AI bit is always set for chips that support it. This
works as there are no code locations that make use of the behaviour with
AI unset (for the chips that support it).
Note that the call to pca953x_setup_gpio() had to be done a bit earlier
to make the NBANK macro work.
The history of this bug is a bit complicated. Commit b32cecb46bdc
("gpio: pca953x: Extract the register address mangling to single
function") changed which chips and functions are affected. Commit
3b00691cc46a ("gpio: pca953x: hack to fix 24 bit gpio expanders") used
some duct tape to make the driver at least appear to work. Commit
49427232764d ("gpio: pca953x: Perform basic regmap conversion")
introduced the caching. Commit b4818afeacbd ("gpio: pca953x: Add
set_multiple to allow multiple bits to be set in one write.") introduced
the .set_multiple() callback which didn't work for chips that need the
AI bit which was fixed later for some chips in 8958262af3fb ("gpio:
pca953x: Repair multi-byte IO address increment on PCA9575"). So I'm
sorry, I don't know which commit I should pick for a Fixes: line.
Tested-by: Marcel Gudert <m.gudert@eckelmann.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
The commit 96d7c7b3e654 ("gpio: gpio-pca953x, Add get_multiple function")
basically did everything wrong from style and code reuse perspective, i.e.
- it didn't utilize existing PCA953x internal helpers
- it didn't utilize bitmap API
- it misses the point that ilog2(), besides that BANK_SFT is useless,
can be used in macros
- it has indentation issues.
Rewrite the function completely.
Cc: Paul Thomas <pthomas8589@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
pca953x_gpio_set_config is setup to support pull-up/down
bias. Currently the driver uses a variable called 'config' to
determine which options to use. Unfortunately, this is incorrect.
This patch uses function pinconf_to_config_param(config), which
converts this 'config' parameter back to pinconfig to determine
which option to use.
Fixes: 15add06841a3 ("gpio: pca953x: add ->set_config implementation")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
This driver uses its own locking but regmap silently uses a mutex for
all operations too. Add the option to disable locking to the regmap
config struct.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Implement a get_multiple function for gpio-pca953x. If a driver
leaves get_multiple unimplemented then gpio_chip_get_multiple()
in gpiolib.c takes care of it by calling chip->get() as needed.
For i2c chips this is very inefficient. For example if you do an
8-bit read then instead of a single i2c transaction there are
8 transactions reading the same byte!
Signed-off-by: Paul Thomas <pthomas8589@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Linux 5.5-rc6
|
|
There is no need to have a forward declaration for pca953x_dt_ids[].
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Since we have driver converted to use bitmap API we must use
traditional bit operations (set_bit(), clear_bit(), etc.)
against it.
Currently IRQ callbacks are missed in the conversion and
thus broken.
Let's fix it right here right now.
Fixes: 35d13d94893f ("gpio: pca953x: convert to use bitmap API")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Don't hardcode irq trigger to IRQF_TRIGGER_LOW while registering IRQ
handler. IRQ/platform core will take care of setting appropriate trigger
type.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
There is no need to split some of the lines. However, improve the style
of multi-line comment. On top of this there is no need to have double
space.
Correct above indentation issues without altering the functionality.
Link: http://lkml.kernel.org/r/20191022172922.61232-12-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Instead of customized approach convert the driver to use bitmap API.
[andriy.shevchenko@linux.intel.com: reduce stack usage in couple of functions]
Link: http://lkml.kernel.org/r/20191023153056.64262-1-andriy.shevchenko@linux.intel.com
Link: http://lkml.kernel.org/r/20191022172922.61232-11-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
While PCA_PCAL is defined for PCA953X type only, we still may use an
offset of the input from regs structure for sake of consistency.
Link: http://lkml.kernel.org/r/20191022172922.61232-10-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We always will have at least one iteration of the loop due to pending
being guaranteed to be non-zero. That is, we may remove extra variable
and check in the IRQ handler.
Link: http://lkml.kernel.org/r/20191022172922.61232-9-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace verbose implementation in set_multiple callback with
for_each_set_clump8 macro to simplify code and improve clarity.
Link: http://lkml.kernel.org/r/3543ffc3668ad4ed4c00e8ebaf14a5559fd6ddf2.1570641097.git.vilhelm.gray@gmail.com
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Phil Reid <preid@electromag.com.au>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Morten Hein Tiljeset <morten.tiljeset@prevas.dk>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It's hard for occasional GPIO code reader/writer to know if values 0/1
equal to IN or OUT. Use defined GPIO_LINE_DIRECTION_IN and
GPIO_LINE_DIRECTION_OUT to help them out.
NOTE - for gpio-amd-fch and gpio-bd9571mwv:
This commit also changes the return value for direction get to equal 1
for direction INPUT. Prior this commit these drivers might have
returned some other positive value but 1 for INPUT.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of changes in the GPIO subsystem for the v5.4 kernel
cycle.
Core changes:
- Support hierarchical GPIO irqchips.
We now have three consumers that can use this: Intel IXP4xx,
ThunderX and Qualcomm SPMI GPIO (in the pinctrl subsystem).
The support code has been long in the making and hashed out so it
should be easily adaptable for all hierarchical irqchip parents.
The code only gets compiled in if hierarchical irqchip is used at
the topmost irq controller at least, as the hierarchical irqchip
requires strict hierarchy all the way up in the system.
- Determine the need for a "valid_mask" for GPIO lines on the
gpio_chip and conversely for the "valid_mask" for the GPIO
interrupt chip interrupt lines by looking for a .init_valid_mask()
callback in the main chip or GPIO interrupt chip respectively.
Allocate it with bitmap_alloc().
- Isolate the device tree/open firmware GPIO description code out in
its own file properly.
- Isolate the ACPI GPIO description code out in its own file
properly.
- Drop a whole lot of #ifdef:s in the main includes: it does not hurt
to keep the include items around, and we get quicker and clearer
compile failures if the appropriate kernel symbols are not selected
for drivers.
New/deleted drivers:
- New driver for Aspeed SGPIO.
- The KS8695 driver is deleted as the platform gets deleted from
arch/arm in this kernel cycle.
- The Cirrus Logic Madera driver now supports CS47L92 and CS47L15.
- The Freescale MPC8xxx now supports LS1028A and LS1088A.
Driver improvements:
- We pass the GPIO irqchip intialization by directly filling in the
struct instead of using set-up functions (the new way) for Intel
MID, Lynxpoint, Merrifield, XLP, HLWD, Aspeed, ZX, VF610, TQMX86,
MT7621, Zynq and EP93xx.
Out-of-band changes:
- Fix a GPIO header inclusion in Unicore - no response from
maintainer.
- Drop FMC subsystem from MAINTAINERS - was deleted in the GPIO tree
last cycle so let's mop up the shards"
* tag 'gpio-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (82 commits)
gpiolib: of: add a fallback for wlf,reset GPIO name
gpio: htc-egpio: Remove unused exported htc_egpio_get_wakeup_irq()
gpio: remove explicit comparison with 0
gpio: creg-snps: use devm_platform_ioremap_resource() to simplify code
gpio: devres: Switch to EXPORT_SYMBOL_GPL()
gpio: of: Switch to EXPORT_SYMBOL_GPL()
gpio: of: Make of_gpio_simple_xlate() private
gpio: of: Make of_get_named_gpiod_flags() private
gpio: aspeed: Add in ast2600 details to Aspeed driver
gpio: aspeed: Use ngpio property from device tree if available
gpio: aspeed: Setup irqchip dynamically
gpio/aspeed: Fix incorrect number of banks
gpio: aspeed: Update documentation with ast2600 controllers
gpio: Initialize the irqchip valid_mask with a callback
gpiolib: acpi: make acpi_can_fallback_to_crs() static
gpio: Fix further merge errors
gpio: Fix up merge collision in include file
gpio: of: Normalize return code variable name
gpio: gpiolib: Normalize return code variable name
gpio: ep93xx: Pass irqchip when adding gpiochip
...
|
|
The register number needs to be translated for chips with more than 8
ports. This patch fixes a bug causing all chips with more than 8 GPIO pins
to not work correctly.
Fixes: 0f25fda840a9 ("gpio: pca953x: Zap ad-hoc reg_direction cache")
Cc: Cc: <stable@vger.kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
The type of reg_direction needs to match the type of the regmap, which
is u8.
Fixes: 0f25fda840a9 ("gpio: pca953x: Zap ad-hoc reg_direction cache")
Cc: Cc: <stable@vger.kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
There is no need to use %s for constant string literals
w/o special characters inside.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
There is no need to explicitly compare return code with 0.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Use GENMASK() macro for all definitions where it's appropriate.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Instead of open coded variants, switch to direct use of
device_get_match_data().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the big slew of GPIO changes for the v5.3 kernel cycle. This
is mostly incremental work this time.
Three important things:
- The FMC subsystem is deleted through my tree. This happens through
GPIO as its demise was discussed in relation to a patch decoupling
its GPIO implementation from the standard way of handling GPIO. As
it turns out, that is not the only subsystem it reimplements and
the authors think it is better do scratch it and start over using
the proper kernel subsystems than try to polish the rust shiny. See
the commit (ACKed by the maintainers) for details.
- Arnd made a small devres patch that was ACKed by Greg and goes into
the device core.
- SPDX header change colissions may happen, because at times I've
seen that quite a lot changed during the -rc:s in regards to SPDX.
(It is good stuff, tglx has me convinced, and it is worth the
occasional pain.)
Apart from this is is nothing controversial or problematic.
Summary:
Core:
- When a gpio_chip request GPIOs from itself, it can now fully
control the line characteristics, both machine and consumer flags.
This makes a lot of sense, but took some time before I figured out
that this is how it has to work.
- Several smallish documentation fixes.
New drivers:
- The PCA953x driver now supports the TI TCA9539.
- The DaVinci driver now supports the K3 AM654 SoCs.
Driver improvements:
- Major overhaul and hardening of the OMAP driver by Russell King.
- Starting to move some drivers to the new API passing irq_chip along
with the gpio_chip when adding the gpio_chip instead of adding it
separately.
Unrelated:
- Delete the FMC subsystem"
* tag 'gpio-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
Revert "gpio: tegra: Clean-up debugfs initialisation"
gpiolib: Use spinlock_t instead of struct spinlock
gpio: stp-xway: allow compile-testing
gpio: stp-xway: get rid of the #include <lantiq_soc.h> dependency
gpio: stp-xway: improve module clock error handling
gpio: stp-xway: simplify error handling in xway_stp_probe()
gpiolib: Clarify use of non-sleeping functions
gpiolib: Fix references to gpiod_[gs]et_*value_cansleep() variants
gpiolib: Document new gpio_chip.init_valid_mask field
Documentation: gpio: Fix reference to gpiod_get_array()
gpio: pl061: drop duplicate printing of device name
gpio: altera: Pass irqchip when adding gpiochip
gpio: siox: Use devm_ managed gpiochip
gpio: siox: Add struct device *dev helper variable
gpio: siox: Pass irqchip when adding gpiochip
drivers: gpio: amd-fch: make resource struct const
devres: allow const resource arguments
gpio: ath79: Pass irqchip when adding gpiochip
gpio: tegra: Clean-up debugfs initialisation
gpio: siox: Switch to IRQ_TYPE_NONE
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fix from Linus Walleij:
"A single fix for the PCA953x driver affecting some fringe variants of
the chip"
* tag 'gpio-v5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pca953x: hack to fix 24 bit gpio expanders
|
|
24 bit expanders use REG_ADDR_AI in combination with register addressing. This
conflicts with regmap which takes this bit as part of the register number,
i.e. a second cache entry is defined for accessed with REG_ADDR_AI being
set although on the chip it is the same register as with REG_ADDR_AI being
cleared.
The problem was introduced by
commit b32cecb46bdc ("gpio: pca953x: Extract the register address mangling to single function")
but only became visible by
commit 8b9f9d4dc511 ("regmap: verify if register is writeable before writing operations")
because before, the regmap size was effectively ignored and
pca953x_writeable_register() did know to ignore REG_ADDR_AI. Still, there
were two separate cache entries created.
Since the use of REG_ADDR_AI seems to be static we can work around this
issue by simply increasing the size of the regmap to cover the "virtual"
registers with REG_ADDR_AI being set. This only means that half of the
regmap buffer will be unused.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 315 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.503150771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The TI TCA9539 is a variant of the PCA953x GPIO expander,
with 16 GPIOs and interrupt functionality.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The NXP PCA6416, documented at [1], is a variant of the PCA GPIO
expander with 16 GPIOs, and supporting an interrupt.
[1] https://www.nxp.com/docs/en/data-sheet/PCA6416A.pdf
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When adding support for the pcal6416, the of_device_id table was left out,
add the proper entry.
Fixes: aac1e3c9680b ("gpio: pca953x: add support for pcal6416 type")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio: updates for v5.2 (part 1)
- batch of improvements for the vf610 driver which shrink the code and
make use of resource managed helpers
- support for a new variant of pca953x
- make gpio-mockup buildable on systems without IOMEM
- make gpio-74x164 more flexible by using generic device properties
plus minor improvements
- new driver for Mellanox BlueField
- fixes for wakeup GPIOs in gpio-omap
- use devm_platform_ioremap_resource() in gpio-mxc
- a couple improvements of kernel docs for ACPI code
- don't WARN() in gpiod_put() on optional GPIOs
|
|
If a device is part of the wake-up path, it should indicate this by
setting its power.wakeup_path field. This allows the genpd core code to
keep the device enabled during system suspend when needed.
As regulators powering devices are not handled by genpd, the driver
handles these itself, and thus must skip regulator control when the
device is part of the wake-up path.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The ON Semiconductor CAT9554 is a variant of the PCA953x GPIO expander,
with 8 GPIOs and interrupt functionality.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
The commit 0cdf21b34e30
("gpio: pca953x: set the PCA_PCAL flag also when matching by DT")
introduces a helper macro which tells that chip supports latched interrupts,
but the macro was never used for ACPI or legacy enumeration.
So, make use of it for legacy and ACPI enumeration.
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If a PCA953x gpio was used as an interrupt and then released,
the shutdown function was trying to extract the pca953x_chip
pointer directly from the irq_data, but in reality was getting
the gpio_chip structure.
The net effect was that the subsequent writes to the data
structure corrupted data in the gpio_chip structure, which wasn't
immediately obvious until attempting to use the GPIO again in the
future, at which point the kernel panics.
This fix correctly extracts the pca953x_chip structure via the
gpio_chip structure, as is correctly done in the other irq
functions.
Fixes: 0a70fe00efea ("gpio: pca953x: Clear irq trigger type on irq shutdown")
Cc: stable@vger.kernel.org
Signed-off-by: Mark Walton <mark.walton@serialtek.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Implement the irq_set_wake() method in the (optional) irq_chip of the
GPIO expander, and propagate wake-up settings to the upstream interrupt
controller. This allows GPIOs connected to a PCA953X GPIO expander to
serve as wake-up sources.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio updates for v5.1
- support for a new variant of pca953x
- documentation fix from Wolfram
- some tegra186 name changes
- two minor fixes for madera and altera-a10sr
|
|
The NXP PCAL6416, documented at [1], is a variant of the PCA GPIO
expander with 16 GPIOs, and supporting an interrupt and the "extended"
features for interrupt, pull-up/pull-down configuration, etc.
[1] https://www.nxp.com/docs/en/data-sheet/PCAL6416A.pdf
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
|
|
This commit adds a minimal implementation of the ->set_config() hook,
with support for the PIN_CONFIG_BIAS_PULL_UP and
PIN_CONFIG_BIAS_PULL_DOWN configurations.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When a system has two PCA953x GPIO expanders, the kernel complains with:
gpio gpiochip2: (0-0021): detected irqchip that is shared with multiple gpiochips: please fix the driver.
Indeed, there is a single instance of "struct irq_chip" that gets
re-used for both PCA953x instance. This commit moves the "struct
irq_chip" to be part of the "struct pca953x_chip", so that we have one
"struct irq_chip" per PCA953X instance.
As part of this, the name of the irq_chip is also made different on a
per-instance basis, now using the dev_name() of the I2C device. This
changes what is visible in /proc/interrupts.
Before:
47: 0 0 pca953x 10 Edge e0100000.sdhci cd
48: 0 0 pca953x 6 Edge e0101000.sdhci cd
After:
47: 0 0 0-0020 10 Edge e0100000.sdhci cd
48: 2 0 0-0020 6 Edge e0101000.sdhci cd
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The current design of pca953x_irq_setup() is:
if (all conditions to support IRQ are met) {
lots of code to support IRQs, which goes to a serious indentation
level.
}
return 0;
It makes more sense to handle this like this:
if (!all conditions to support IRQ are met)
return 0;
handle IRQ support
This commit does just this change, reducing by one tab the indentation
level of the IRQ setup code. Thanks to this reduced indentation level,
we are less restricted by the 80-column limit, and we can have more
function arguments on the same line.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fixes the following sparse warning:
drivers/gpio/gpio-pca953x.c:292:28: warning:
symbol 'pca953x_i2c_regmap' was not declared. Should it be static?
Fixes: 49427232764d ("gpio: pca953x: Perform basic regmap conversion")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.21 kernel series.
Core changes:
- Some core changes are already in outside of this pull request as
they came through the regulator tree, most notably
devm_gpiod_unhinge() that removes devres refcount management from a
GPIO descriptor. This is needed in subsystems such as regulators
where the regulator core need to take over the reference counting
and lifecycle management for a GPIO descriptor.
- We dropped devm_gpiochip_remove() and devm_gpio_chip_match() as
nothing needs it. We can bring it back if need be.
- Add a global TODO so people see where we are going. This helps
setting the direction now that we are two GPIO maintainers.
- Handle the MMC CD/WP properties in the device tree core. (The bulk
of patches activating this code is already merged through the
MMC/SD tree.)
- Augment gpiochip_request_own_desc() to pass a flag so we as
gpiochips can request lines as active low or open drain etc even
from ourselves.
New drivers:
- New driver for Cadence GPIO blocks.
- New driver for Atmel SAMA5D2 PIOBU GPIO lines.
Driver improvements:
- A major refactoring of the PCA953x driver - this driver has been
around for ages, and is now modernized to reduce code duplication
that has stacked up and is using regmap to read write and cache
registers.
- Intel drivers are now maintained in a separate tree and start with
a round of cleanups and unifications"
* tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (99 commits)
gpio: sama5d2-piobu: Depend on OF_GPIO
gpio: Add Cadence GPIO driver
dt-bindings: gpio: Add bindings for Cadence GPIO
gpiolib-acpi: remove unused variable 'err', cleans up build warning
gpio: mxs: read pin level directly instead of using .get
gpio: aspeed: remove duplicated statement
gpio: add driver for SAMA5D2 PIOBU pins
dt-bindings: arm: atmel: describe SECUMOD usage as a GPIO controller
gpio/mmc/of: Respect polarity in the device tree
dt-bindings: gpio: rcar: Add r8a774c0 (RZ/G2E) support
memory: omap-gpmc: Get the header of the enum
ARM: omap1: Fix new user of gpiochip_request_own_desc()
gpio: pca953x: Add regmap dependency for PCA953x driver
gpio: raspberrypi-exp: decrease refcount on firmware dt node
gpiolib: Fix return value of gpio_to_desc() stub if !GPIOLIB
gpio: pca953x: Restore registers after suspend/resume cycle
gpio: pca953x: Zap single use of pca953x_read_single()
gpio: pca953x: Zap ad-hoc reg_output cache
gpio: pca953x: Zap ad-hoc reg_direction cache
gpio: pca953x: Perform basic regmap conversion
...
|
|
Instead of using the name directly from the I2C client
to name the gpio_chip, use dev_name() on the client->dev,
so we get the sometimes more unique device name, as I2C has
a mechanism for naming its devices explicitly in e.g.
board data.
This is a prerequisite for being able to reference
uniquely any I2C GPIO expander defined in a board file
when setting up GPIO descriptor tables.
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
It is possible that the PCA953x is powered down during suspend.
Use regmap cache to assure the registers in the PCA953x are in
line with the driver state after resume.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Drop pca953x_write_single() which is used in one place.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Replace the ad-hoc reg_output output register caching with generic
regcache cache. Drop pca953x_write_single() which is no longer used.
This reduces code duplication.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Replace the ad-hoc reg_direction direction register caching with generic
regcache cache. This reduces code duplication.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
