| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Some late GPIO fixes for the v5.9 series:
- Fix compiler warnings on the OMAP when PM is disabled
- Clear the interrupt when setting edge sensitivity on the Spreadtrum
driver.
- Fix up spurious interrupts on the TC35894.
- Support threaded interrupts on the Siox controller.
- Fix resource leaks on the mockup driver.
- Fix line event handling in syscall compatible mode for the
character device.
- Fix an unitialized variable in the PCA953A driver.
- Fix access to all GPIO IRQs on the Aspeed AST2600.
- Fix line direction on the AMD FCH driver.
- Use the bitmap API instead of compiler intrinsics for bit
manipulation in the PCA953x driver"
* tag 'gpio-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pca953x: Correctly initialize registers 6 and 7 for PCA957x
gpio: pca953x: Use bitmap API over implicit GCC extension
gpio: amd-fch: correct logic of GPIO_LINE_DIRECTION
gpio: aspeed: fix ast2600 bank properties
gpio/aspeed-sgpio: don't enable all interrupts by default
gpio/aspeed-sgpio: enable access to all 80 input & output sgpios
gpio: pca953x: Fix uninitialized pending variable
gpiolib: Fix line event handling in syscall compatible mode
gpio: mockup: fix resource leak in error path
gpio: siox: explicitly support only threaded irqs
gpio: tc35894: fix up tc35894 interrupt configuration
gpio: sprd: Clear interrupt when setting the type as edge
gpio: omap: Fix warnings if PM is disabled
|
|
Currently, the IRQ setup for the SGPIO driver enables all interrupts in
dual-edge trigger mode. Since the default handler is handle_bad_irq, any
state change on input GPIOs will trigger bad IRQ warnings.
This change applies sensible IRQ defaults: single-edge trigger, and all
IRQs disabled.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae79b ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Currently, the aspeed-sgpio driver exposes up to 80 GPIO lines,
corresponding to the 80 status bits available in hardware. Each of these
lines can be configured as either an input or an output.
However, each of these GPIOs is actually an input *and* an output; we
actually have 80 inputs plus 80 outputs.
This change expands the maximum number of GPIOs to 160; the lower half
of this range are the input-only GPIOs, the upper half are the outputs.
We fix the GPIO directions to correspond to this mapping.
This also fixes a bug when setting GPIOs - we were reading from the
input register, making it impossible to set more than one output GPIO.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae79b ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
This fixes some various typos.
Signed-off-by: Sachin Agarwal <asachin591@gmail.com>
Link: https://lore.kernel.org/r/20200118105319.68637-1-sachinagarwal@sachins-MacBook-2.local
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
gcc has a hard time tracking whether BUG_ON(1) ends
execution or not:
drivers/gpio/gpio-aspeed-sgpio.c: In function 'bank_reg':
drivers/gpio/gpio-aspeed-sgpio.c:112:1: error: control reaches end of non-void function [-Werror=return-type]
Use the simpler BUG() that gcc knows cannot continue.
Fixes: f8b410e3695a ("gpio: aspeed-sgpio: Rename and add Kconfig/Makefile")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
This renames the "gpio-aspeed" driver to conform with other
GPIO drivers as "gpio-aspeed-sgpio.c". All GPIO drivers
should start with the string "gpio-" no special exceptions.
Also the Kconfig and Makefile entries should normally
go with the driver but I missed this in my review, sorry
for mistake. "CONFIG_GPIO_ASPEED_SGPIO" is used to
activate this driver.
Cc: Hongwei Zhang <hongweiz@ami.com>
Fixes: 7db47faae79b ("gpio: aspeed: Add SGPIO driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190927114833.12551-1-linus.walleij@linaro.org
|
