summaryrefslogtreecommitdiff
path: root/drivers/gnss
AgeCommit message (Collapse)Author
2018-12-10Merge 4.20-rc6 into tty-nextGreg Kroah-Hartman
We want the TTY changes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-12-06gnss: sirf: fix activation retry handlingJohan Hovold
Fix activation helper which would return -ETIMEDOUT even if the last retry attempt was successful. Also change the semantics of the retries variable so that it actually holds the number of retries (rather than tries). Fixes: d2efbbd18b1e ("gnss: add driver for sirfstar-based receivers") Cc: stable <stable@vger.kernel.org> # 4.19 Signed-off-by: Johan Hovold <johan@kernel.org>
2018-11-27serdev: make synchronous write return bytes writtenJohan Hovold
Make the synchronous serdev_device_write() helper behave analogous to the asynchronous serdev_device_write_buf() by returning the number of bytes written (or rather buffered) also on timeout. This will allow drivers to distinguish the case where data was partially written from the case where no data was written. Also update the only two users that checked the return value. Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-14gnss: sirf: fix synchronous write timeoutJohan Hovold
Passing a timeout of zero to the synchronous serdev_device_write() helper does currently not imply to wait forever (unlike passing zero to serdev_device_wait_until_sent()). Instead, if there's insufficient room in the write buffer, we'd end up with an incomplete write. Fixes: d2efbbd18b1e ("gnss: add driver for sirfstar-based receivers") Cc: stable <stable@vger.kernel.org> # 4.19 Signed-off-by: Johan Hovold <johan@kernel.org>
2018-11-14gnss: serial: fix synchronous write timeoutJohan Hovold
Passing a timeout of zero to the synchronous serdev_device_write() helper does currently not imply to wait forever (unlike passing zero to serdev_device_wait_until_sent()). Instead, if there's insufficient room in the write buffer, we'd end up with an incomplete write. Fixes: 37768b054f20 ("gnss: add generic serial driver") Cc: stable <stable@vger.kernel.org> # 4.19 Signed-off-by: Johan Hovold <johan@kernel.org>
2018-07-16gnss: fix potential error pointer dereferenceDan Carpenter
The gnss_allocate_device() function returns a mix of NULL and error pointers on error. It should only return one or the other. Since the callers both check for NULL, I've modified it to return NULL on error. Fixes: 2b6a44035143 ("gnss: add GNSS receiver subsystem") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-07-16gnss: ubx: make struct ubx_gserial_ops staticColin Ian King
The structure ubx_gserial_ops is local to the source and does not need to be in global scope, so make it static. Cleans up sparse warning: symbol 'ubx_gserial_ops' was not declared. Should it be static? Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-06-28gnss: add receiver type supportJohan Hovold
Add a "type" device attribute and a "GNSS_TYPE" uevent variable which can be used to determine the type of a GNSS receiver. The currently identified types reflect the protocol(s) supported by a receiver: "NMEA" NMEA 0183 "SiRF" SiRF Binary "UBX" UBX Note that both SiRF and UBX type receivers typically support a subset of NMEA 0183 with vendor extensions (e.g. to allow switching to the vendor protocol). Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-06-28gnss: add driver for sirfstar-based receiversJohan Hovold
Add driver for serial-connected SiRFstar-based GNSS receivers. These devices typically boot into hibernate mode from which they can be woken using a pulse on the ON_OFF input pin. Once active, a pulse on the same ON_OFF pin is used to put the device back into hibernate mode. The current state can be determined by sampling the WAKEUP output. Hardware configurations where WAKEUP has been connected to ON_OFF (and where an initial WAKEUP pulse during boot is sufficient to have the device boot into active mode) are also supported. In this case, device power is managed using the main-supply regulator only. Note that configurations where WAKEUP is left not connected, so that the device power state can only indirectly be determined using the I/O interface, is currently not supported. It should be fairly straight-forward to extend the current implementation with such support however (and this this is the main reason for not using the generic serial implementation for this driver). Note that timepulse-support is left unimplemented. Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-06-28gnss: add driver for u-blox receiversJohan Hovold
Add driver for serial-connected u-blox GNSS receivers. Note that the driver uses the generic GNSS serial implementation and therefore essentially only manages power abstracted into three power states: ACTIVE, STANDBY, and OFF. For u-blox receivers with a main supply and no enable-gpios, this simply means that the main supply is disabled in STANDBY and OFF (the optional backup supply is kept enabled while the driver is bound). Note that timepulse-support is not yet implemented. Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-06-28gnss: add generic serial driverJohan Hovold
Add a generic serial GNSS driver (library) which provides a common implementation for the gnss interface and power management (runtime and system suspend). This allows GNSS drivers for specific chip to be implemented by simply providing a set_power() callback to handle three states: ACTIVE, STANDBY and OFF. Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-06-28gnss: add GNSS receiver subsystemJohan Hovold
Add a new subsystem for GNSS (e.g. GPS) receivers. While GNSS receivers are typically accessed using a UART interface they often also support other I/O interfaces such as I2C, SPI and USB, while yet other devices use iomem or even some form of remote-processor messaging (rpmsg). The new GNSS subsystem abstracts the underlying interface and provides a new "gnss" class type, which exposes a character-device interface (e.g. /dev/gnss0) to user space. This allows GNSS receivers to have a representation in the Linux device model, something which is important not least for power management purposes. Note that the character-device interface provides raw access to whatever protocol the receiver is (currently) using, such as NMEA 0183, UBX or SiRF Binary. These protocols are expected to be continued to be handled by user space for the time being, even if some hybrid solutions are also conceivable (e.g. to have kernel drivers issue management commands). This will still allow for better platform integration by allowing GNSS devices and their resources (e.g. regulators and enable-gpios) to be described by firmware and managed by kernel drivers rather than platform-specific scripts and services. While the current interface is kept minimal, it could be extended using IOCTLs, sysfs or uevents as needs and proper abstraction levels are identified and determined (e.g. for device and feature identification). Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>