| Age | Commit message (Collapse) | Author |
|---|
|
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The maximum unicast datagram size /without/ link fragmentation is
4096 - 4 = 4092 (max IEEE 1394 async payload size at >= S800 bus speed,
minus unfragmented encapssulation header). Max broadcast datagram size
without fragmentation is 8 bytes less than that (due to GASP header).
The maximum datagram size /with/ link fragmentation is 0xfff = 4095
for unicast and broadcast. This is because the RFC 2734 fragment
encapsulation header field for datagram size is only 12 bits wide.
Fixes: 5d48f00d836a('firewire: net: fix maximum possible MTU')
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CardBus cards
firewire-net, like the older eth1394 driver, reduced the initial MTU to
less than 1500 octets if the local link layer controller's asynchronous
packet reception limit was lower.
This is bogus, since this reception limit does not have anything to do
with the transmission limit. Neither did this reduction affect the TX
path positively, nor could it prevent link fragmentation at the RX path.
Many FireWire CardBus cards have a max_rec of 9, causing an initial MTU
of 1024 - 16 = 1008. RFC 2734 and RFC 3146 allow a minimum max_rec = 8,
which would result in an initial MTU of 512 - 16 = 496. On such cards,
IPv6 could only be employed if the MTU was manually increased to 1280 or
more, i.e. IPv6 would not work without intervention from userland.
We now always initialize the MTU to 1500, which is the default according
to RFC 2734 and RFC 3146.
On a VIA VT6316 based CardBus card which was affected by this, changing
the MTU from 1008 to 1500 also increases TX bandwidth by 6 %.
RX remains unaffected.
CC: netdev@vger.kernel.org
CC: linux1394-devel@lists.sourceforge.net
CC: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit b3e3893e1253 ("net: use core MTU range checking in misc drivers")
mistakenly introduced an upper limit for firewire-net's MTU based on the
local link layer controller's reception capability. Revert this. Neither
RFC 2734 nor our implementation impose any particular upper limit.
Actually, to be on the safe side and to make the code explicit, set
ETH_MAX_MTU = 65535 as upper limit now.
(I replaced sizeof(struct rfc2734_header) by the equivalent
RFC2374_FRAG_HDR_SIZE in order to avoid distracting long/int conversions.)
Fixes: b3e3893e1253('net: use core MTU range checking in misc drivers')
CC: netdev@vger.kernel.org
CC: linux1394-devel@lists.sourceforge.net
CC: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
firewire-net:
- set min/max_mtu
- remove fwnet_change_mtu
nes:
- set max_mtu
- clean up nes_netdev_change_mtu
xpnet:
- set min/max_mtu
- remove xpnet_dev_change_mtu
hippi:
- set min/max_mtu
- remove hippi_change_mtu
batman-adv:
- set max_mtu
- remove batadv_interface_change_mtu
- initialization is a little async, not 100% certain that max_mtu is set
in the optimal place, don't have hardware to test with
rionet:
- set min/max_mtu
- remove rionet_change_mtu
slip:
- set min/max_mtu
- streamline sl_change_mtu
um/net_kern:
- remove pointless ndo_change_mtu
hsi/clients/ssi_protocol:
- use core MTU range checking
- remove now redundant ssip_pn_set_mtu
ipoib:
- set a default max MTU value
- Note: ipoib's actual max MTU can vary, depending on if the device is in
connected mode or not, so we'll just set the max_mtu value to the max
possible, and let the ndo_change_mtu function continue to validate any new
MTU change requests with checks for CM or not. Note that ipoib has no
min_mtu set, and thus, the network core's mtu > 0 check is the only lower
bounds here.
mptlan:
- use net core MTU range checking
- remove now redundant mpt_lan_change_mtu
fddi:
- min_mtu = 21, max_mtu = 4470
- remove now redundant fddi_change_mtu (including export)
fjes:
- min_mtu = 8192, max_mtu = 65536
- The max_mtu value is actually one over IP_MAX_MTU here, but the idea is to
get past the core net MTU range checks so fjes_change_mtu can validate a
new MTU against what it supports (see fjes_support_mtu in fjes_hw.c)
hsr:
- min_mtu = 0 (calls ether_setup, max_mtu is 1500)
f_phonet:
- min_mtu = 6, max_mtu = 65541
u_ether:
- min_mtu = 14, max_mtu = 15412
phonet/pep-gprs:
- min_mtu = 576, max_mtu = 65530
- remove redundant gprs_set_mtu
CC: netdev@vger.kernel.org
CC: linux-rdma@vger.kernel.org
CC: Stefan Richter <stefanr@s5r6.in-berlin.de>
CC: Faisal Latif <faisal.latif@intel.com>
CC: linux-rdma@vger.kernel.org
CC: Cliff Whickman <cpw@sgi.com>
CC: Robin Holt <robinmholt@gmail.com>
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Marek Lindner <mareklindner@neomailbox.ch>
CC: Simon Wunderlich <sw@simonwunderlich.de>
CC: Antonio Quartulli <a@unstable.cc>
CC: Sathya Prakash <sathya.prakash@broadcom.com>
CC: Chaitra P B <chaitra.basappa@broadcom.com>
CC: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
CC: MPT-FusionLinux.pdl@broadcom.com
CC: Sebastian Reichel <sre@kernel.org>
CC: Felipe Balbi <balbi@kernel.org>
CC: Arvid Brodin <arvid.brodin@alten.se>
CC: Remi Denis-Courmont <courmisch@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no check if ioremap_nocache() returns a valid pointer.
Potentially it can lead to null pointer dereference.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (renamed goto labels)
|
|
Replace all trans_start updates with netif_trans_update helper.
change was done via spatch:
struct net_device *d;
@@
- d->trans_start = jiffies
+ netif_trans_update(d)
Compile tested only.
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: linux-xtensa@linux-xtensa.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-rdma@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: MPT-FusionLinux.pdl@broadcom.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-can@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-hams@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: devel@driverdev.osuosl.org
Cc: b.a.t.m.a.n@lists.open-mesh.org
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire leftover from Stefan Richter:
"Occurrences of timeval were supposed to be eliminated last round, now
remove a last forgotten one"
* tag 'firewire-update2' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: nosy: Replace timeval with timespec64
|
|
Firewire was using is_compat_task to check whether it was in a compat
ioctl or a non-compat ioctl. Use is_compat_syscall instead so it works
properly on all architectures.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
'struct timeval' uses a 32 bit field for its 'seconds' value which
will overflow in year 2038 and beyond. This patch replaces the use
of timeval in nosy.c with timespec64 which doesn't suffer from y2038
issue. The code is correct as is - since it is only using the
microseconds portion of timeval. However, this patch does the
replacement as part of a larger effort to remove all instances of
'struct timeval' from the kernel (that would help identify cases
where the code is actually broken).
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire updates from Stefan Richter:
"IEEE 1394 subsystem patches:
- move away from outmoded timekeeping API
- error reporting fix
- documentation bits"
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ABI documentation: libhinawa uses firewire-cdev
firewire: ABI documentation: jujuutils were renamed to linux-firewire-utils
firewire: ohci: propagate return code from soft_reset to probe and resume
firewire: nosy: Replace timeval with timespec64
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire fix from Stefan Richter:
"Work around JMicron initialization quirk, which ffected isochronous
transmission, e.g. audio via FFADO or ALSA"
* tag 'firewire-update' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ohci: fix JMicron JMB38x IT context discovery
|
|
sleep and avoiding waking kswapd
__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts. They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve". __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".
Over time, callers had a requirement to not block when fallback options
were available. Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.
This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative. High priority users continue to use
__GFP_HIGH. __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim. __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim. __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.
This patch then converts a number of sites
o __GFP_ATOMIC is used by callers that are high priority and have memory
pools for those requests. GFP_ATOMIC uses this flag.
o Callers that have a limited mempool to guarantee forward progress clear
__GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
into this category where kswapd will still be woken but atomic reserves
are not used as there is a one-entry mempool to guarantee progress.
o Callers that are checking if they are non-blocking should use the
helper gfpflags_allow_blocking() where possible. This is because
checking for __GFP_WAIT as was done historically now can trigger false
positives. Some exceptions like dm-crypt.c exist where the code intent
is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
flag manipulations.
o Callers that built their own GFP flags instead of starting with GFP_KERNEL
and friends now also need to specify __GFP_KSWAPD_RECLAIM.
The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.
The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL. They may
now wish to specify __GFP_KSWAPD_RECLAIM. It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
software_reset() may fail
- due to unresponsive chip with -EBUSY (-16), or
- due to ejected or unseated card with -ENODEV (-19).
Let the PCI probe and resume routines log the actual error code instead
of hardwired -EBUSY.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
32 bit systems using 'struct timeval' will break in the year 2038, so
we replace the code appropriately. However, this driver is not broken
in 2038 since we are using only the microseconds portion of the
current time.
This patch replaces timeval with timespec64.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Reported by Clifford and Craig for JMicron OHCI-1394 + SDHCI combo
controllers: Often or even most of the time, the controller is
initialized with the message "added OHCI v1.10 device as card 0, 4 IR +
0 IT contexts, quirks 0x10". With 0 isochronous transmit DMA contexts
(IT contexts), applications like audio output are impossible.
However, OHCI-1394 demands that at least 4 IT contexts are implemented
by the link layer controller, and indeed JMicron JMB38x do implement
four of them. Only their IsoXmitIntMask register is unreliable at early
access.
With my own JMB381 single function controller I found:
- I can reproduce the problem with a lower probability than Craig's.
- If I put a loop around the section which clears and reads
IsoXmitIntMask, then either the first or the second attempt will
return the correct initial mask of 0x0000000f. I never encountered
a case of needing more than a second attempt.
- Consequently, if I put a dummy reg_read(...IsoXmitIntMaskSet)
before the first write, the subsequent read will return the correct
result.
- If I merely ignore a wrong read result and force the known real
result, later isochronous transmit DMA usage works just fine.
So let's just fix this chip bug up by the latter method. Tested with
JMB381 on kernel 3.13 and 4.3.
Since OHCI-1394 generally requires 4 IT contexts at a minium, this
workaround is simply applied whenever the initial read of IsoXmitIntMask
returns 0, regardless whether it's a JMicron chip or not. I never heard
of this issue together with any other chip though.
I am not 100% sure that this fix works on the OHCI-1394 part of JMB380
and JMB388 combo controllers exactly the same as on the JMB381 single-
function controller, but so far I haven't had a chance to let an owner
of a combo chip run a patched kernel.
Strangely enough, IsoRecvIntMask is always reported correctly, even
though it is probed right before IsoXmitIntMask.
Reported-by: Clifford Dunn
Reported-by: Craig Moore <craig.moore@qenos.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
'0' is now used as the default cmd_per_lun value,
so there's no need to explicitly set it to '1' in the
host template.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that there are no more users kill dev_rebuild_header and all of it's
implementations.
This is long overdue.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The kernel was using the vendor ID 0xd00d1e, which was inherited from
the old ieee1394 driver stack. However, this ID was not registered, and
invalid.
Instead, use the vendor/model IDs that are now officially assigned to
the kernel:
https://ieee1394.wiki.kernel.org/index.php/IEEE_OUI_Assignments
[stefanr:
- The vendor ID 001f11 is Openmoko, Inc.'s identifier, registered at
IEEE Registration Authority.
- The range of model IDs 023900...0239ff are the Linux kernel 1394
subsystem's identifiers, registered at Openmoko.
- Model ID 023901 is picked by the subsystem developers as
firewire-core's model ID.]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
[Bart van Asche:] SCSI core never sets cmd->sc_data_direction to
DMA_BIDIRECTIONAL; scsi_bidi_cmnd(cmd) should be used instead to
test for a bidirectional command.
[Christoph Hellwig:] Bidirectional commands won't ever be queued
anyway, unless a LLD or transport driver sets QUEUE_FLAG_BIDI.
So, simply remove the respective queuecommand check in the SBP-2
transport driver.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Remove the function ar_prev_buffer_index() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
firewire-core uses fw_card.lock to protect topology data and transaction
data. firewire-sbp2 uses fw_card.lock for entirely unrelated purposes.
Introduce a sbp2_target.lock to firewire-sbp2 and replace all
fw_card.lock uses in the driver. fw_card.lock is now entirely private
to firewire-core. This has no immediate advantage apart from making it
clear in the code that firewire-sbp2 does not interact with the core
via the core lock.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Users of card->lock Calling context
------------------------------------------------------------------------
sbp2_status_write AR-req handler, tasklet
complete_transaction AR-resp or AT-req handler, tasklet
sbp2_send_orb among else scsi host .queuecommand, which may
be called in some sort of atomic context
sbp2_cancel_orbs sbp2_send_management_orb/
sbp2_{login,reconnect,remove},
worklet or process
sbp2_scsi_abort, scsi eh thread
sbp2_allow_block sbp2_login, worklet
sbp2_conditionally_block among else complete_command_orb, tasklet
sbp2_conditionally_unblock sbp2_{login,reconnect}, worklet
sbp2_unblock sbp2_{login,remove}, worklet or process
Drop the IRQ flags saving from sbp2_cancel_orbs,
sbp2_conditionally_unblock, and sbp2_unblock.
It was already omitted in sbp2_allow_block.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
The assertion in the comment in sbp2_allow_block() is no longer true.
Or maybe it never was true. At least now, the sole caller of
sbp2_allow_block(), sbp2_login, can run concurrently to one of
sbp2_unblock()'s callers, sbp2_remove.
sbp2_login is performed by sbp2_logical_unit.work.
sbp2_remove is performed by fw_device.work.
sbp2_remove cancels sbp2_logical_unit.work, but only after it called
sbp2_unblock.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
fw_csr_string() truncates and terminates target strings like strlcpy()
does. Unlike strlcpy(), it returns the target strlen, not the source
strlen, hence users of fw_csr_string() are unable to detect truncation.
Point this behavior out in the kerneldoc comment.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
|
|
vm_map_ram() is intended for short-lived objects, so using it for the AR
buffers could fragment address space, especially on a 32-bit machine.
For an allocation that lives as long as the device, vmap() is the better
choice.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Found by the UC-KLEE tool: A user could supply less input to
firewire-cdev ioctls than write- or write/read-type ioctl handlers
expect. The handlers used data from uninitialized kernel stack then.
This could partially leak back to the user if the kernel subsequently
generated fw_cdev_event_'s (to be read from the firewire-cdev fd)
which notably would contain the _u64 closure field which many of the
ioctl argument structures contain.
The fact that the handlers would act on random garbage input is a
lesser issue since all handlers must check their input anyway.
The fix simply always null-initializes the entire ioctl argument buffer
regardless of the actual length of expected user input. That is, a
runtime overhead of memset(..., 40) is added to each firewirew-cdev
ioctl() call. [Comment from Clemens Ladisch: This part of the stack is
most likely to be already in the cache.]
Remarks:
- There was never any leak from kernel stack to the ioctl output
buffer itself. IOW, it was not possible to read kernel stack by a
read-type or write/read-type ioctl alone; the leak could at most
happen in combination with read()ing subsequent event data.
- The actual expected minimum user input of each ioctl from
include/uapi/linux/firewire-cdev.h is, in bytes:
[0x00] = 32, [0x05] = 4, [0x0a] = 16, [0x0f] = 20, [0x14] = 16,
[0x01] = 36, [0x06] = 20, [0x0b] = 4, [0x10] = 20, [0x15] = 20,
[0x02] = 20, [0x07] = 4, [0x0c] = 0, [0x11] = 0, [0x16] = 8,
[0x03] = 4, [0x08] = 24, [0x0d] = 20, [0x12] = 36, [0x17] = 12,
[0x04] = 20, [0x09] = 24, [0x0e] = 4, [0x13] = 40, [0x18] = 4.
Reported-by: David Ramos <daramos@stanford.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Pull networking updates from David Miller:
"Highlights:
1) Steady transitioning of the BPF instructure to a generic spot so
all kernel subsystems can make use of it, from Alexei Starovoitov.
2) SFC driver supports busy polling, from Alexandre Rames.
3) Take advantage of hash table in UDP multicast delivery, from David
Held.
4) Lighten locking, in particular by getting rid of the LRU lists, in
inet frag handling. From Florian Westphal.
5) Add support for various RFC6458 control messages in SCTP, from
Geir Ola Vaagland.
6) Allow to filter bridge forwarding database dumps by device, from
Jamal Hadi Salim.
7) virtio-net also now supports busy polling, from Jason Wang.
8) Some low level optimization tweaks in pktgen from Jesper Dangaard
Brouer.
9) Add support for ipv6 address generation modes, so that userland
can have some input into the process. From Jiri Pirko.
10) Consolidate common TCP connection request code in ipv4 and ipv6,
from Octavian Purdila.
11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.
12) Generic resizable RCU hash table, with intial users in netlink and
nftables. From Thomas Graf.
13) Maintain a name assignment type so that userspace can see where a
network device name came from (enumerated by kernel, assigned
explicitly by userspace, etc.) From Tom Gundersen.
14) Automatic flow label generation on transmit in ipv6, from Tom
Herbert.
15) New packet timestamping facilities from Willem de Bruijn, meant to
assist in measuring latencies going into/out-of the packet
scheduler, latency from TCP data transmission to ACK, etc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
cxgb4 : Disable recursive mailbox commands when enabling vi
net: reduce USB network driver config options.
tg3: Modify tg3_tso_bug() to handle multiple TX rings
amd-xgbe: Perform phy connect/disconnect at dev open/stop
amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
net: sun4i-emac: fix memory leak on bad packet
sctp: fix possible seqlock seadlock in sctp_packet_transmit()
Revert "net: phy: Set the driver when registering an MDIO bus device"
cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
team: Simplify return path of team_newlink
bridge: Update outdated comment on promiscuous mode
net-timestamp: ACK timestamp for bytestreams
net-timestamp: TCP timestamping
net-timestamp: SCHED timestamp on entering packet scheduler
net-timestamp: add key to disambiguate concurrent datagrams
net-timestamp: move timestamp flags out of sk_flags
net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
cxgb4i : Move stray CPL definitions to cxgb4 driver
tcp: reduce spurious retransmits due to transient SACK reneging
qlcnic: Initialize dcbnl_ops before register_netdev
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer and time updates from Thomas Gleixner:
"A rather large update of timers, timekeeping & co
- Core timekeeping code is year-2038 safe now for 32bit machines.
Now we just need to fix all in kernel users and the gazillion of
user space interfaces which rely on timespec/timeval :)
- Better cache layout for the timekeeping internal data structures.
- Proper nanosecond based interfaces for in kernel users.
- Tree wide cleanup of code which wants nanoseconds but does hoops
and loops to convert back and forth from timespecs. Some of it
definitely belongs into the ugly code museum.
- Consolidation of the timekeeping interface zoo.
- A fast NMI safe accessor to clock monotonic for tracing. This is a
long standing request to support correlated user/kernel space
traces. With proper NTP frequency correction it's also suitable
for correlation of traces accross separate machines.
- Checkpoint/restart support for timerfd.
- A few NOHZ[_FULL] improvements in the [hr]timer code.
- Code move from kernel to kernel/time of all time* related code.
- New clocksource/event drivers from the ARM universe. I'm really
impressed that despite an architected timer in the newer chips SoC
manufacturers insist on inventing new and differently broken SoC
specific timers.
[ Ed. "Impressed"? I don't think that word means what you think it means ]
- Another round of code move from arch to drivers. Looks like most
of the legacy mess in ARM regarding timers is sorted out except for
a few obnoxious strongholds.
- The usual updates and fixlets all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
timekeeping: Fixup typo in update_vsyscall_old definition
clocksource: document some basic timekeeping concepts
timekeeping: Use cached ntp_tick_length when accumulating error
timekeeping: Rework frequency adjustments to work better w/ nohz
timekeeping: Minor fixup for timespec64->timespec assignment
ftrace: Provide trace clocks monotonic
timekeeping: Provide fast and NMI safe access to CLOCK_MONOTONIC
seqcount: Add raw_write_seqcount_latch()
seqcount: Provide raw_read_seqcount()
timekeeping: Use tk_read_base as argument for timekeeping_get_ns()
timekeeping: Create struct tk_read_base and use it in struct timekeeper
timekeeping: Restructure the timekeeper some more
clocksource: Get rid of cycle_last
clocksource: Move cycle_last validation to core code
clocksource: Make delta calculation a function
wireless: ath9k: Get rid of timespec conversions
drm: vmwgfx: Use nsec based interfaces
drm: i915: Use nsec based interfaces
timekeeping: Provide ktime_get_raw()
hangcheck-timer: Use ktime_get_ns()
...
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire regression fix from Stefan Richter:
"IEEE 1394 (FireWire) subsystem fix: MSI don't work on VIA PCIe
controllers with some isochronous workloads (regression since
v3.16-rc1)"
* tag 'firewire-fix-vt6315' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ohci: disable MSI for VIA VT6315 again
|
|
Revert half of commit d151f9854f21: If isochronous I/O is attempted with
packets larget than 1 kByte, VIA VT6315 rev 01 immediately stops to generate
any interrupts if MSI are used. Fix this by going back to legacy interrupts.
[Thread "Isochronous streaming with VT6315 OHCI",
http://marc.info/?t=139049641500003]
With smaller packets, the loss of IRQs happens too but only very rarely ---
rarely eneough that it was not yet possible for me to determine whether
QUIRK_NO_MSI is an actual fix for this rare variation of this chip bug.
I am keeping QUIRK_CYCLE_TIMER off of VT6315 rev >= 1 because this has been
verified by myself with certainty. On the other hand, I am also keeping
QUIRK_CYCLE_TIMER on for VT6315 rev 0 because I don't know at this time
whether this revision accesses Cycle Timer non-atomically like most of the
other VIA OHCIs are known to do.
Reported-by: Rémy Bruno <remy-fw@remy.trinnov.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend alloc_netdev{,_mq{,s}}() to take name_assign_type as argument, and convert
all users to pass NET_NAME_UNKNOWN.
Coccinelle patch:
@@
expression sizeof_priv, name, setup, txqs, rxqs, count;
@@
(
-alloc_netdev_mqs(sizeof_priv, name, setup, txqs, rxqs)
+alloc_netdev_mqs(sizeof_priv, name, NET_NAME_UNKNOWN, setup, txqs, rxqs)
|
-alloc_netdev_mq(sizeof_priv, name, setup, count)
+alloc_netdev_mq(sizeof_priv, name, NET_NAME_UNKNOWN, setup, count)
|
-alloc_netdev(sizeof_priv, name, setup)
+alloc_netdev(sizeof_priv, name, NET_NAME_UNKNOWN, setup)
)
v9: move comments here from the wrong commit
Signed-off-by: Tom Gundersen <teg@jklm.no>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire fix from Stefan Richter:
"The 1394 drivers cannot and are not supposed to be built on platforms
which don't provide the DMA mapping API (regression since v3.16-rc1
with CONFIG_COMPILE_TEST=y on some architectures)"
* tag 'firewire-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: IEEE 1394 (FireWire) support should depend on HAS_DMA
|
|
Commit b3d681a4fc108f9653bbb44e4f4e72db2b8a5734 ("firewire: Use
COMPILE_TEST for build testing") added COMPILE_TEST as an alternative
dependency for the purpose of build testing the firewire core.
However, this bypasses all other implicit dependencies assumed by PCI,
like HAS_DMA.
If NO_DMA=y:
drivers/built-in.o: In function `fw_iso_buffer_destroy':
(.text+0x36a096): undefined reference to `dma_unmap_page'
drivers/built-in.o: In function `fw_iso_buffer_map_dma':
(.text+0x36a164): undefined reference to `dma_map_page'
drivers/built-in.o: In function `fw_iso_buffer_map_dma':
(.text+0x36a172): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `sbp2_send_management_orb':
sbp2.c:(.text+0x36c6b4): undefined reference to `dma_map_single'
sbp2.c:(.text+0x36c6c8): undefined reference to `dma_mapping_error'
sbp2.c:(.text+0x36c772): undefined reference to `dma_map_single'
sbp2.c:(.text+0x36c786): undefined reference to `dma_mapping_error'
sbp2.c:(.text+0x36c854): undefined reference to `dma_unmap_single'
sbp2.c:(.text+0x36c872): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sbp2_map_scatterlist':
sbp2.c:(.text+0x36ccbc): undefined reference to `scsi_dma_map'
sbp2.c:(.text+0x36cd36): undefined reference to `dma_map_single'
sbp2.c:(.text+0x36cd4e): undefined reference to `dma_mapping_error'
sbp2.c:(.text+0x36cd84): undefined reference to `scsi_dma_unmap'
drivers/built-in.o: In function `sbp2_unmap_scatterlist':
sbp2.c:(.text+0x36cda6): undefined reference to `scsi_dma_unmap'
sbp2.c:(.text+0x36cdc6): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `complete_command_orb':
sbp2.c:(.text+0x36d6ac): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sbp2_scsi_queuecommand':
sbp2.c:(.text+0x36d8e0): undefined reference to `dma_map_single'
sbp2.c:(.text+0x36d8f6): undefined reference to `dma_mapping_error'
Add an explicit dependency on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
do_posix_clock_monotonic_gettime() is a leftover from the initial
posix timer implementation which maps to ktime_get_ts()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Link: http://lkml.kernel.org/r/20140611234607.351283464@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound into next
Pull sound updates from Takashi Iwai:
"At this time, majority of changes come from ASoC world while we got a
few new drivers in other places for FireWire and USB. There have been
lots of ASoC core cleanups / refactoring, but very little visible to
external users.
ASoC:
- Support for specifying aux CODECs in DT
- Removal of the deprecated mux and enum macros
- More moves towards full componentisation
- Removal of some unused I/O code
- Lots of cleanups, fixes and enhancements to the davinci, Freescale,
Haswell and Realtek drivers
- Several drivers exposed directly in Kconfig for use with
simple-card
- GPIO descriptor support for jacks
- More updates and fixes to the Freescale SSI, Intel and rsnd drivers
- New drivers for Cirrus CS42L56, Realtek RT5639, RT5642 and RT5651
and ST STA350, Analog Devices ADAU1361, ADAU1381, ADAU1761 and
ADAU1781, and Realtek RT5677
HD-audio:
- Clean up Dell headset quirks
- Noise fixes for Dell and Sony laptops
- Thinkpad T440 dock fix
- Realtek codec updates (ALC293,ALC233,ALC3235)
- Tegra HD-audio HDMI support
FireWire-audio:
- FireWire audio stack enhancement (AMDTP, MIDI), support for
incoming isochronous stream and duplex streams with timestamp
synchronization
- BeBoB-based devices support
- Fireworks-based device support
USB-audio:
- Behringer BCD2000 USB device support
Misc:
- Clean up of a few old drivers, atmel, fm801, etc"
* tag 'sound-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (480 commits)
ASoC: Fix wrong argument for card remove callbacks
ASoC: free jack GPIOs before the sound card is freed
ALSA: firewire-lib: Remove a comment about restriction of asynchronous operation
ASoC: cache: Fix error code when not using ASoC level cache
ALSA: hda/realtek - Fix COEF widget NID for ALC260 replacer fixup
ALSA: hda/realtek - Correction of fixup codes for PB V7900 laptop
ALSA: firewire-lib: Use IEC 61883-6 compliant labels for Raw Audio data
ASoC: add RT5677 CODEC driver
ASoC: intel: The Baytrail/MAX98090 driver depends on I2C
ASoC: rt5640: Add the function "get_clk_info" to RL6231 shared support
ASoC: rt5640: Add the function of the PLL clock calculation to RL6231 shared support
ASoC: rt5640: Add RL6231 class device shared support for RT5640, RT5645 and RT5651
ASoC: cache: Fix possible ZERO_SIZE_PTR pointer dereferencing error.
ASoC: Add helper functions to cast from DAPM context to CODEC/platform
ALSA: bebob: sizeof() vs ARRAY_SIZE() typo
ASoC: wm9713: correct mono out PGA sources
ALSA: synth: emux: soundfont.c: Cleaning up memory leak
ASoC: fsl: Remove dependencies of boards for SND_SOC_EUKREA_TLV320
ASoC: fsl-ssi: Use regmap
ASoC: fsl-ssi: reorder and document fsl_ssi_private
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394 into next
Pull firewire updates from Stefan Richter:
"IEEE 1394 (FireWire) subsystem changes: One optimization for some VIA
controllers, one fix, one kconfig brushup"
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ohci: enable MSI for VIA VT6315 rev 1, drop cycle timer quirk
firewire: Use COMPILE_TEST for build testing
firewire: net: fix NULL derefencing in fwnet_probe()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into next
Pull core locking updates from Ingo Molnar:
"The main changes in this cycle were:
- reduced/streamlined smp_mb__*() interface that allows more usecases
and makes the existing ones less buggy, especially in rarer
architectures
- add rwsem implementation comments
- bump up lockdep limits"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (33 commits)
rwsem: Add comments to explain the meaning of the rwsem's count field
lockdep: Increase static allocations
arch: Mass conversion of smp_mb__*()
arch,doc: Convert smp_mb__*()
arch,xtensa: Convert smp_mb__*()
arch,x86: Convert smp_mb__*()
arch,tile: Convert smp_mb__*()
arch,sparc: Convert smp_mb__*()
arch,sh: Convert smp_mb__*()
arch,score: Convert smp_mb__*()
arch,s390: Convert smp_mb__*()
arch,powerpc: Convert smp_mb__*()
arch,parisc: Convert smp_mb__*()
arch,openrisc: Convert smp_mb__*()
arch,mn10300: Convert smp_mb__*()
arch,mips: Convert smp_mb__*()
arch,metag: Convert smp_mb__*()
arch,m68k: Convert smp_mb__*()
arch,m32r: Convert smp_mb__*()
arch,ia64: Convert smp_mb__*()
...
|
|
Commit af0cdf494781 "firewire: ohci: fix regression with VIA VT6315,
disable MSI" acted upon a report against VT6315 rev 0:
http://linux.derkeiler.com/Mailing-Lists/Kernel/2010-12/msg02301.html
$ lspci -nn
VIA Technologies, Inc. VT6315 Series Firewire Controller [1106:3403]
I now got a card with
$ lspci -nn
VIA Technologies, Inc. VT6315 Series Firewire Controller [1106:3403] (rev 01)
and this works fine with MSI enabled.
Second, I tested this VT6315 rev 1 without CYCLE_TIMER quirk flag using
http://me.in-berlin.de/~s5r6/linux1394/utils/test_cycle_time_v20100125.c
and found that this chip does in fact access the cycle timer atomically.
Things I can't test because I don't have the hardware:
- whether VT6315 rev 0 really needs QUIRK_CYCLE_TIMER,
- whether the VT6320 PCI device needs QUIRK_CYCLE_TIMER,
- whether the VT6325 and VT6330 PCIe devices need QUIRK_CYCLE_TIMER
and QUIRK_NO_MSI.
Hence, just add a whitelist entry specifically for VT6315 rev >= 1
without any quirk flags. Before this entry we need an extra entry to
catch VT6315 rev <= 0 due to how our ID matching logic works.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Undo a feature introduced in v3.14 by commit fcd46b34425d
"firewire: Enable remote DMA above 4 GB". That change raised the
minimum address at which protocol drivers and user programs can register
for request reception from 0x0001'0000'0000 to 0x8000'0000'0000.
It turned out that at least one vendor-specific protocol exists which
uses lower addresses: https://bugzilla.kernel.org/show_bug.cgi?id=76921
For the time being, revert most of commit fcd46b34425d so that affected
protocols work like with kernel v3.13 and before. Just keep the valid
documentation parts from the regressing commit, and the ability to
identify controllers which could be programmed to accept >32 bit
physical DMA addresses. The rest of fcd46b34425d should probably be
brought back as an optional instead of default feature.
Reported-by: Fabien Spindler <fabien.spindler@inria.fr>
Cc: <stable@vger.kernel.org> # 3.14+
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
In post commit, a quirk of this firmware about transactions is reported.
This commit apply a workaround for this quirk.
They often fail transactions due to gap_count mismatch. This state is changed
by generating bus reset.
The fw_schedule_bus_reset() is an exported symbol in firewire-core. But there
are no header for public. This commit moves its prototype from
drivers/firewire/core.h to include/linux/firewire.h.
This mismatch still affects bus management before generating this bus reset.
It still takes a time to call driver's probe() because transactions are still
often failed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Stop using BROKEN as an alternative dependency for the purpose of
build testing the firewire core. The newly introduced COMPILE_TEST is
better suited for that purpose.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
"dev" and "net" are NULL when alloc_netdev() is failed.
So just unlock and return an error.
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Mostly scripted conversion of the smp_mb__* barriers.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/n/tip-55dhyhocezdw1dg7u19hmh1u@git.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-arch@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fix from Tejun Heo:
"This pull request contains a workqueue usage fix for firewire.
For quite a long time now, workqueue only treats two work items
identical iff both their addresses and callbacks match. This is to
avoid introducing false dependency through the work item being
recycled while being executed. This changes non-reentrancy guarantee
for the users of PREPARE[_DELAYED]_WORK() - if the function changes,
reentrancy isn't guaranteed against the previous instance. Firewire
depended on such nonreentrancy guarantee.
This is fixed by doing the work item multiplexing from firewire proper
while keeping the work function unchanged"
* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
firewire: don't use PREPARE_DELAYED_WORK
|
|
PREPARE_[DELAYED_]WORK() are being phased out. They have few users
and a nasty surprise in terms of reentrancy guarantee as workqueue
considers work items to be different if they don't have the same work
function.
firewire core-device and sbp2 have been been multiplexing work items
with multiple work functions. Introduce fw_device_workfn() and
sbp2_lu_workfn() which invoke fw_device->workfn and
sbp2_logical_unit->workfn respectively and always use the two
functions as the work functions and update the users to set the
->workfn fields instead of overriding work functions using
PREPARE_DELAYED_WORK().
This fixes a variety of possible regressions since a2c1c57be8d9
"workqueue: consider work function when searching for busy work items"
due to which fw_workqueue lost its required non-reentrancy property.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: linux1394-devel@lists.sourceforge.net
Cc: stable@vger.kernel.org # v3.9+
Cc: stable@vger.kernel.org # v3.8.2+
Cc: stable@vger.kernel.org # v3.4.60+
Cc: stable@vger.kernel.org # v3.2.40+
|
|
Since commit bd972688eb24
"firewire: ohci: Fix 'failed to read phy reg' on FW643 rev8",
there is a high chance that firewire-ohci fails to initialize LSI née
Agere controllers.
https://bugzilla.kernel.org/show_bug.cgi?id=65151
Peter Hurley points out the reason: IEEE 1394a:2000 clause 5A.1 (or
IEEE 1394:2008 clause 17.2.1) say: "The PHY shall insure that no more
than 10 ms elapse from the reassertion of LPS until the interface is
reset. The link shall not assert LReq until the reset is complete."
In other words, the link needs to give the PHY at least 10 ms to get
the interface operational.
With just the msleep(1) in bd972688eb24, the first read_phy_reg()
during ohci_enable() may happen before the phy-link interface reset was
finished, and fail. Due to the high variability of msleep(n) with small
n, this failure was not fully reproducible, and not apparent at all with
low CONFIG_HZ setting.
On the other hand, Peter can no longer reproduce the issue with FW643
rev8. The read phy reg failures that happened back then may have had an
unrelated cause. So, just revert bd972688eb24, except for the valid
comment on TSB82AA2 cards.
Reported-by: Mikhail Gavrilov
Reported-by: Jay Fenlason <fenlason@redhat.com>
Reported-by: Clemens Ladisch <clemens@ladisch.de>
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
