| Age | Commit message (Collapse) | Author |
|---|
|
The commit 2895b2cad6e7 ("dmaengine: dw: fix cyclic transfer callbacks")
re-enabled BLOCK interrupts with regard to make cyclic transfers work. However,
this change becomes a regression for non-cyclic transfers as interrupt counters
under stress test had been grown enormously (approximately per 4-5 bytes in the
UART loop back test).
Taking into consideration above enable BLOCK interrupts if and only if channel
is programmed to perform cyclic transfer.
Fixes: 2895b2cad6e7 ("dmaengine: dw: fix cyclic transfer callbacks")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Tested-by: Mans Rullgard <mans@mansr.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
When retrieving the residue value, the SRC/DST fields of the
active PaRAM are read to determine the current position of
the DMA engine. However, the AM335x Technical Reference Manual
states:
11.3.3.6 Parameter Set Updates
After the TR is read from the PaRAM (and is in the process
of being submitted to the EDMA3TC), the following fields are
updated as needed: ... SRC DST
This means SRC/DST is incremented even though the DMA transfer
may not have started yet or is in progress. Thus if the reader
of the residue accesses the DMA buffer too quickly, the CPU is
misinformed about the data that has been successfully processed.
The CCSTAT.ACTV register is a boolean that is set if any TR is
being processed by either the EMDA3CC or EDMA3TC. By polling
this register it is possible to ensure that the residue value
returned is valid for immediate processing. However, since the
DMA engine may be active, polling may never hit a moment where
no TR is being processed. To handle this, the SRC/DST is also
polled to see if it changes. And as a last resort, a max loop
count for the busy waiting exists to avoid an infinite loop.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
WildcatPoint PCH as seen on MacBook 12-inch (Early 2015) has PCI enabled
DesignWare DMA controller. Enable it by adding its ID to the corresponding
driver.
Reported-by: Leif Liddy <leif.liddy@gmail.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=110901
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
idle
The timer_event() function seems to have a bug where it ends up marking the
last entry as non-responding and eventually attempts to restart the
channel. This also continuously happen when idle. What needs to happen is
for us to make sure there are no descriptors active and then handle that
case properly. We should only hit the "cleanup" stage if there are still
active descriptors.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"Here is my second pull request for this window:
A few driver fixes have piled up and one missed rcar bindings patch
which got somehow lost in for-linus branch so cherry-picked that one.
Fixes are for dw, at_hdmac, edma"
* tag 'dmaengine-fix-4.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: rcar-dmac: Document SoC specific bindings
dmaengine: at_xdmac: fix resume for cyclic transfers
dmaengine: dw: fix cyclic transfer callbacks
dmaengine: dw: fix cyclic transfer setup
dmaengine: edma: Fix paRAM slot allocation for entry channel 0
|
|
When having cyclic transfers, the channel was paused when performing
suspend but was not correctly resumed.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee707 ("dmaengine: at_xdmac: creation of the atmel
eXtended DMA Controller driver")
Cc: <stable@vger.kernel.org> # 4.1 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"We've had quite busy weeks in this cycle. Looking at ALSA core, the
significant changes are a few fixes wrt timer and sequencer ioctls
that have been revealed by fuzzer recently. Other than that, ASoC
core got a few updates about DAI link handling, but these are rather
straightforward refactoring.
In drivers scene, ASoC received quite lots of new drivers in addition
to bunch of updates for still ongoing Intel Skylake support and
topology API. HD-audio gained a new HDMI/DP hotplug notification via
component. FireWire got a pile of code refactoring/updates with
SCS.1x driver integration.
More highlights are shown below.
[ NOTE: this contains also many commits for DRM. This is due to the
pull of drm stable branch into sound tree, as the base of i915 audio
component work for HD-audio. The highlights below don't contain
these DRM changes, as these are supposed to be pulled via drm tree
in anyway sooner or later. ]
Core:
- Handful fixes to harden ALSA timer and sequencer ioctls against
races reported by syzkaller fuzzer
- Irq description string can be unique to each card; only for
HD-audio for now
ASoC:
- Conversion of the array of DAI links to a list for supporting
dynamically adding and removing DAI links
- Topology API enhancements to make everything more component based
and being able to specify PCM links via topology
- Some more fixes for the topology code, though it is still not final
and ready for enabling in production; we really need to get to the
point where that can be done
- A pile of changes for Intel SkyLake drivers which hopefully deliver
some useful initial functionality for systems with this chipset,
though there is more work still to come
- Lots of new features and cleanups for the Renesas drivers
- ANC support for WM5110
- New drivers: Imagination Technologies IPs, Atmel class D speaker,
Cirrus CS47L24 and WM1831, Dialog DA7128, Realtek RT5659 and
RT56156, Rockchip RK3036, TI PC3168A, and AMD ACP
- Rename PCM1792a driver to be generic pcm179x
HD-Audio:
- Use audio component for i915 HDMI/DP hotplug handling
- On-demand binding with i915 driver
- bdl_pos_adj parameter adjustment for Baytrail controllers
- Enable power_save_node for CX20722; this shouldn't lead to
regression, hopefully
- Kabylake HDMI/DP codec support
- Quirks for Lenovo E50-80, Dell Latitude E-series, and other Dell
machines
- A few code refactoring
FireWire:
- Lots of code cleanup and refactoring
- Integrate the support of SCS.1x devices into snd-oxfw driver;
snd-scs1x driver is obsoleted
USB-audio:
- Fix possible NULL dereference at disconnection
- A regression fix for Native Instruments devices
Misc:
- A few code cleanups of fm801 driver"
* tag 'sound-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (722 commits)
ALSA: timer: Code cleanup
ALSA: timer: Harden slave timer list handling
ALSA: hda - Add fixup for Dell Latitidue E6540
ALSA: timer: Fix race among timer ioctls
ALSA: hda - add codec support for Kabylake display audio codec
ALSA: timer: Fix double unlink of active_list
ALSA: usb-audio: Fix mixer ctl regression of Native Instrument devices
ALSA: hda - fix the headset mic detection problem for a Dell laptop
ALSA: hda - Fix white noise on Dell Latitude E5550
ALSA: hda_intel: add card number to irq description
ALSA: seq: Fix race at timer setup and close
ALSA: seq: Fix missing NULL check at remove_events ioctl
ALSA: usb-audio: Avoid calling usb_autopm_put_interface() at disconnect
ASoC: hdac_hdmi: remove unused hdac_hdmi_query_pin_connlist
ASoC: AMD: Add missing include file
ALSA: hda - Fixup inverted internal mic for Lenovo E50-80
ALSA: usb: Add native DSD support for Oppo HA-1
ASoC: Make aux_dev more like a generic component
ASoC: bcm2835: cleanup includes by ordering them alphabetically
ASoC: AMD: Manage ACP 2.x SRAM banks power
...
|
|
Cyclic transfer callbacks rely on block completion interrupts which were
disabled in commit ff7b05f29fd4 ("dmaengine/dw_dmac: Don't handle block
interrupts"). This re-enables block interrupts so the cyclic callbacks
can work. Other transfer types are not affected as they set the INT_EN
bit only on the last block.
Fixes: ff7b05f29fd4 ("dmaengine/dw_dmac: Don't handle block interrupts")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cc: <stable@vger.kernel.org>
|
|
Commit 61e183f83069 ("dmaengine/dw_dmac: Reconfigure interrupt and
chan_cfg register on resume") moved some channel initialisation to
a new function which must be called before starting a transfer.
This updates dw_dma_cyclic_start() to use dwc_dostart() like the other
modes, thus ensuring dwc_initialize() gets called and removing some code
duplication.
Fixes: 61e183f83069 ("dmaengine/dw_dmac: Reconfigure interrupt and chan_cfg register on resume")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cc: <stable@vger.kernel.org>
|
|
Pull dmaengine updates from Vinod Koul:
"This round we have few new features, new driver and updates to few
drivers.
The new features to dmaengine core are:
- Synchronized transfer termination API to terminate the dmaengine
transfers in synchronized and async fashion as required by users.
We have its user now in ALSA dmaengine lib, img, at_xdma, axi_dmac
drivers.
- Universal API for channel request and start consolidation of
request flows. It's user is ompa-dma driver.
- Introduce reuse of descriptors and use in pxa_dma driver
Add/Remove:
- New STM32 DMA driver
- Removal of unused R-Car HPB-DMAC driver
Updates:
- ti-dma-crossbar updates for supporting eDMA
- tegra-apb pm updates
- idma64
- mv_xor updates
- ste_dma updates"
* tag 'dmaengine-4.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (54 commits)
dmaengine: mv_xor: add suspend/resume support
dmaengine: mv_xor: de-duplicate mv_chan_set_mode*()
dmaengine: mv_xor: remove mv_xor_chan->current_type field
dmaengine: omap-dma: Add support for DMA filter mapping to slave devices
dmaengine: edma: Add support for DMA filter mapping to slave devices
dmaengine: core: Introduce new, universal API to request a channel
dmaengine: core: Move and merge the code paths using private_candidate
dmaengine: core: Skip mask matching when it is not provided to private_candidate
dmaengine: mdc: Correct terminate_all handling
dmaengine: edma: Add probe callback to edma_tptc_driver
dmaengine: dw: fix potential memory leak in dw_dma_parse_dt()
dmaengine: stm32-dma: Fix unchecked deference of chan->desc
dmaengine: sh: Remove unused R-Car HPB-DMAC driver
dmaengine: usb-dmac: Document SoC specific compatibility strings
ste_dma40: Delete an unnecessary variable initialisation in d40_probe()
ste_dma40: Delete another unnecessary check in d40_probe()
ste_dma40: Delete an unnecessary check before the function call "kmem_cache_destroy"
dmaengine: tegra-apb: Free interrupts before killing tasklets
dmaengine: tegra-apb: Update driver to use GFP_NOWAIT
dmaengine: tegra-apb: Only save channel state for those in use
...
|
|
edma_alloc_slot was not checking the channel mapping support existence when
slot 0 has been requested (used as entry slot for channel/event 0).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
* acpi-soc:
PM / clk: don't leave clocks enabled when driver not bound
i2c: dw: Add APM X-Gene ACPI I2C device support
ACPI / APD: Add APM X-Gene ACPI I2C device support
ACPI / LPSS: change 'does not have' to 'has' in comment
Revert "dmaengine: dw: platform: provide platform data for Intel"
dmaengine: dw: return immediately from IRQ when DMA isn't in use
dmaengine: dw: platform: power on device on shutdown
ACPI / LPSS: override power state for LPSS DMA device
ACPI / LPSS: power on when probe() and otherwise when remove()
ACPI / LPSS: do delay for all LPSS devices when D3->D0
ACPI / LPSS: allow to use specific PM domain during ->probe()
Revert "ACPI / LPSS: allow to use specific PM domain during ->probe()"
device core: add BUS_NOTIFY_DRIVER_NOT_BOUND notification
x86/platform/iosf_mbi: Remove duplicate definitions
Conflicts:
drivers/i2c/busses/i2c-designware-platdrv.c
|
|
Since we have a work around to prevent a system hangup we don't need to provide
a platform data explicitly anymore.
This reverts commit 175267b389f781748e2bbb6c737e76b5c9bc4c88.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There is no need to bother the hardware when all channels are idle. We have not
to get any interrupts.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We have to call dw_dma_disable() to stop any ongoing transfer. On some
platforms we can't do that since DMA device is powered off. Moreover we have no
possibility at that point to check if the platform is affected or not. That's
why we call pm_runtime_get_sync() / pm_runtime_put() unconditionally. On the
other hand we can't use pm_runtime_suspended() because runtime PM framework is
not fully used by the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
For interrupt controller that doesn't support irq_disable and hardware
with level interrupt, an extra interrupt can be pending. This patch fixes
the issue by setting IRQ_DISABLE_UNLAZY flag for the interrupt line.
Reference: http://git.kernel.org/tip/e9849777d0e27cdd2902805be51da73e7c79578c
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This commit adds suspend/resume support to the mv_xor driver. The
config and interrupt mask registers must be saved and restored, and
upon resume, the MBus windows configuration must also be done again.
Tested on Armada 388 GP, with a RAID 5 array, accessed before and
after a suspend to RAM cycle.
Based on work from Ofer Heifetz and Lior Amsalem.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
When commit 6f166312c6ea2 ("dmaengine: mv_xor: add support for a38x
command in descriptor mode") added support for the descriptor mode
available in Marvell Armada 38x and later SoCs, it added a new
function mv_chan_set_mode_to_desc() which allows to configure a XOR
channel to get the specific operation to be done from each individual
DMA descriptor.
However, this function was mainly a duplicate of the existing
mv_chan_set_mode(), with just the operation being different.
This commit re-organizes the code into a single mv_chan_set_mode()
function, which takes the operation mode as argument, and the
mv_xor_channel_add() function decides whether to use
XOR_OPERATION_MODE_IN_DESC or XOR_OPERATION_MODE_XOR.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Since commit 3e4f52e2da9f6 ("dma: mv_xor: Simplify the DMA_MEMCPY
operation"), this field is no longer used, so get rid of it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This reverts commit e958e079e254 ("dmaengine: mic_x100: add missing
spin_unlock").
The above patch is incorrect. There is nothing wrong with the original
code. The spin_lock is acquired in the "prep" functions and released
in "submit".
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
'asoc/topic/ssm2518' and 'asoc/topic/sti' into asoc-next
|
|
Add support for providing device to filter_fn mapping so client drivers
can switch to use the dma_request_chan() API.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Add support for providing device to filter_fn mapping so client drivers
can switch to use the dma_request_chan() API.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The two API function can cover most, if not all current APIs used to
request a channel. With minimal effort dmaengine drivers, platforms and
dmaengine user drivers can be converted to use the two function.
struct dma_chan *dma_request_chan_by_mask(const dma_cap_mask_t *mask);
To request any channel matching with the requested capabilities, can be
used to request channel for memcpy, memset, xor, etc where no hardware
synchronization is needed.
struct dma_chan *dma_request_chan(struct device *dev, const char *name);
To request a slave channel. The dma_request_chan() will try to find the
channel via DT, ACPI or in case if the kernel booted in non DT/ACPI mode
it will use a filter lookup table and retrieves the needed information from
the dma_slave_map provided by the DMA drivers.
This legacy mode needs changes in platform code, in dmaengine drivers and
finally the dmaengine user drivers can be converted:
For each dmaengine driver an array of DMA device, slave and the parameter
for the filter function needs to be added:
static const struct dma_slave_map da830_edma_map[] = {
{ "davinci-mcasp.0", "rx", EDMA_FILTER_PARAM(0, 0) },
{ "davinci-mcasp.0", "tx", EDMA_FILTER_PARAM(0, 1) },
{ "davinci-mcasp.1", "rx", EDMA_FILTER_PARAM(0, 2) },
{ "davinci-mcasp.1", "tx", EDMA_FILTER_PARAM(0, 3) },
{ "davinci-mcasp.2", "rx", EDMA_FILTER_PARAM(0, 4) },
{ "davinci-mcasp.2", "tx", EDMA_FILTER_PARAM(0, 5) },
{ "spi_davinci.0", "rx", EDMA_FILTER_PARAM(0, 14) },
{ "spi_davinci.0", "tx", EDMA_FILTER_PARAM(0, 15) },
{ "da830-mmc.0", "rx", EDMA_FILTER_PARAM(0, 16) },
{ "da830-mmc.0", "tx", EDMA_FILTER_PARAM(0, 17) },
{ "spi_davinci.1", "rx", EDMA_FILTER_PARAM(0, 18) },
{ "spi_davinci.1", "tx", EDMA_FILTER_PARAM(0, 19) },
};
This information is going to be needed by the dmaengine driver, so
modification to the platform_data is needed, and the driver map should be
added to the pdata of the DMA driver:
da8xx_edma0_pdata.slave_map = da830_edma_map;
da8xx_edma0_pdata.slavecnt = ARRAY_SIZE(da830_edma_map);
The DMA driver then needs to configure the needed device -> filter_fn
mapping before it registers with dma_async_device_register() :
ecc->dma_slave.filter_map.map = info->slave_map;
ecc->dma_slave.filter_map.mapcnt = info->slavecnt;
ecc->dma_slave.filter_map.fn = edma_filter_fn;
When neither DT or ACPI lookup is available the dma_request_chan() will
try to match the requester's device name with the filter_map's list of
device names, when a match found it will use the information from the
dma_slave_map to get the channel with the dma_get_channel() internal
function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Channel matching with private_candidate() is used in two paths, the error
checking is slightly different in them and they are duplicating code also.
Move the code under find_candidate() to provide consistent execution and
going to allow us to reuse this mode of channel lookup later.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
If mask is NULL skip the mask matching against the DMA device capabilities.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Use of the CANCEL bit in mdc_terminate_all creates an
additional 'command done' to appear in the registers (in
addition to an interrupt).
In addition, there is a potential race between
mdc_terminate_all and the irq handler if a transfer
completes at the same time as the terminate all (presently
this results in an inappropriate warning).
To handle these issues, any outstanding 'command done'
events are cleared during mdc_terminate_all and the irq
handler takes no action when there are no new 'command done'
events.
Signed-off-by: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Due to changes in device and platform code drivers w/o probe will fail to
load. This means that the devices for eDMA TPTCs are goign to be without
driver and omap hwmod code will turn them off after the kernel finished
loading:
[ 3.015900] platform 49800000.tptc: omap_device_late_idle: enabled but no driver. Idling
[ 3.024671] platform 49a00000.tptc: omap_device_late_idle: enabled but no driver. Idling
This will prevent eDMA to work since the TPTCs are not enabled.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Fixes: 34635b1accb9 ("dmaengine: edma: Add dummy driver skeleton for edma3-tptc")
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
If the "dma-channels" DT property is missing, the dw_dma_parse_dt()
function return NULL, but not before allocating memory for a struct
dw_dma_platform_data through devres. If the device supports parameter
detection, the probe still succeeds and the allocated memory is not
released until the device is removed.
Fix this by deferring the allocation until after checking the
"dma-channels" property.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This patch fixes at_xdmac_prep_dma_memcpy(). Indeed the data width field
of the Channel Configuration register was not updated properly in the
loop: the bits of the dwidth field were not cleared before adding their
new value.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee70 ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver")
Cc: stable@vger.kernel.org #4.1 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
'commit d8b468394fb7 ("dmaengine: Add STM32 DMA driver")' leads to the
following Smatch complaint:
drivers/dma/stm32-dma.c:562 stm32_dma_issue_pending()
error: we previously assumed 'chan->desc' could be null (see line 560)
So, this patch fixes the unchecked dereference of chan->desc by returning
operation not permitted error when stm32_dma_start_transfer() does not
succeed to allocate a virtual channel descriptor.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
As of commit 4baadb9e05c68962 ("ARM: shmobile: r8a7778: remove obsolete
setup code"), the Renesas R-Car HPB-DMAC driver is no longer used.
In theory it could still be used on R-Car Gen1 SoCs, but that requires
adding DT support to the driver, which is not planned.
Remove the driver, it can be resurrected from git history when needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The variable "res" will eventually be set to a resource pointer from
a call of the d40_hw_detect_init(() function.
Thus let us omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
A single jump label was used by the d40_probe() function in several cases
for error handling which was a bit inefficient here.
* This implementation detail could be improved by the introduction
of another jump label.
* Remove an extra check for the variable "base".
* Omit its explicit initialisation at the beginning then.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
"kmem_cache_destroy"
The kmem_cache_destroy() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
|
|
This change makes the DT file to be easier to read since the reserved slots
array does not need the '/bits/ 16' to be specified, which might confuse
some people.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This change makes the DT file to be easier to read since the memcpy
channels array does not need the '/bits/ 16' to be specified, which might
confuse some people.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
On probe failure or driver removal, before killing any tasklets, ensure
that the channel interrupt is freed to ensure that another channel
interrupt cannot occur and schedule the tasklet again.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
