| Age | Commit message (Collapse) | Author |
|---|
|
The tegra20-apb-dma driver currently uses the flag GFP_ATOMIC when
allocating memory for structures used in conjunction with the DMA
descriptors. It is preferred that dmaengine drivers use GFP_NOWAIT
instead and so the emergency memory pool will not be used by these
drivers.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Currently the tegra-apb DMA driver suspend/resume helpers, save and
restore the registers for all channels regardless of whether they are
in use or not. Change this so that only channels that have been
allocated and configured are saved and restored.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Newer tegra devices have a separate word count register per channel that
contains the number of words to be transferred. This register is not
saved or restored by the suspend/resume helpers for these newer devices
and so ensure that it is.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In the tegra_dma_runtime_suspend/resume functions, the pdev structure
is not needed, and so just call dev_get_drvdata() to get the device
data structure.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The tegra-apb DMA driver enables runtime-pm but never calls
pm_runtime_get/put and hence the runtime-pm callbacks are never invoked.
The driver manages the clocks by directly calling clk_prepare_enable()
and clk_unprepare_disable().
Fix this by replacing the clk_prepare_enable() and clk_disable_unprepare()
with pm_runtime_get_sync() and pm_runtime_put(), respectively. Note that
the consequence of this is that if runtime-pm is disabled, then the clocks
will remain on the entire time the driver is loaded. However, if
runtime-pm is disabled, then power is not most likely not a concern.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
spin lock should be released while returning from function
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Calling synchronize_irq() right before devm_free_irq() is quite useless. On
one hand the IRQ can easily fire again before devm_free_irq() is entered,
on the other hand devm_free_irq() itself calls synchronize_irq() internally
(in a race condition free way), before any state associated with the IRQ is
freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq, dev;
@@
-synchronize_irq(irq);
devm_free_irq(dev, irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
free_irq(irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This add power management suspend/resume support for the fsl-edma
driver.
eDMA acted as a basic function used by others. What it needs to do
is the two steps below to support power management.
In fsl_edma_suspend_late:
Check whether the DMA chan is idle, if it is not idle disable DMA
request.
In fsl_edma_resume_early:
Enable the eDMA and wait for being used.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
f93178291712 dmaengine: bcm2835-dma: Fix memory leak when stopping a
running transfer
Fixed the memleak, but introduced another issue: the terminate_all callback
might be called with interrupts disabled and the dma_free_coherent() is
not allowed to be called when IRQs are disabled.
Convert the driver to use dma_pool_* for managing the list of control
blocks for the transfer.
Fixes: f93178291712 ("dmaengine: bcm2835-dma: Fix memory leak when stopping a running transfer")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
When performing interleaved transfers with numf > 1, an extra line is
copied. The mbr.bc field is incremented once too often. The length of
the block is (BLEN+1) microblocks.
Signed-off-by: Sylvain ETIENNE <Sylvain.ETIENNE@ingenico.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 4e5385784e69 ("dmaengine: at_xdmac: handle numf > 1")
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The code was not in agreement with the comments.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@vger.kernel.org # 4.3 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
There is no need to calculate an overall length of the descriptor each time we
call for DMA transfer status. Instead we do this at descriptor allocation stage
and keep the stored length for further usage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Currently the match DMA controller is done only for lower 32 bits of
address which might be not true on 64-bit platform. Check upper portion
as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Since a local variable contains the number of hardware desriptors at the
beginning of idma64_desc_fill() we may use it to index the last descriptor as
well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Explicitly show in idma64_desc_fill() how we link the hardware
descriptors.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This tells, for example, IOMMU what the maximum size of a segment
the DMA controller can send.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
There is no need to disable interrupts in the IRQ handler. The driver
guarantess that at one time only one descriptor is active, besides the fact
that each call to the same channel will be serialized in idma64_chan_irq()
handler anyway.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Fix typo in a macro which was not used until now. It explains why there
is no error at compilation time.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee707 "dmaengine: at_xdmac: creation of the atmel eXtended
DMA Controller driver"
Cc: stable@vger.kernel.org # 3.19 and later
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
When setting the channel configuration register, the perid field is not
set to 0 since it is useless for mem2mem transfers. Unfortunately, a
device has 0 as perid. It could cause spurious flags status because
the controller could mix some events from the two channels.
For that reason, use the highest perid value for mem2mem transfers since it
doesn't match the perid of other devices.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This patch fixes an issue that list_for_each_entry() in
usb_dmac_chan_terminate_all() is possible to cause endless loop because
this will move own desc to the desc_freed. So, this driver should use
list_for_each_entry_safe() instead of list_for_each_entry().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
When a DMA client driver decides that it is not providing callback for
completion of a transfer (and/or does not set the DMA_PREP_INTERRUPT) but
it will poll the status of the transfer (in case of short memcpy for
example) we will not get interrupt for the completion of the transfer and
will not mark the transaction as done.
Check the channel enable bit in the CCR when the status is queried and if
the channel is no longer active, we call the omap_dma_callback() to handle
the transfer completion.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The use of tasklet to actually start the DMA transfer slightly decreases the
DMA throughput since it adds small scheduling delay when the transfer is
started. In normal use, even with high I/O load the tasklet would start
one transaction at a time, however running the DMAtest for memcpy on all
available channels will cause the tasklet to start about 15 transfers.
The performance numbers on OMAP4 PandaBoard-es (test_buf_size = 6553):
With the tasklet:
dmatest: dma0chan30-copy: summary 5000 tests, 0 failures 186 iops 593 KB/s (0)
dmatest: dma0chan8-copy0: summary 5000 tests, 0 failures 184 iops 584 KB/s (0)
dmatest: dma0chan13-copy: summary 5000 tests, 0 failures 184 iops 585 KB/s (0)
dmatest: dma0chan12-copy: summary 5000 tests, 0 failures 184 iops 585 KB/s (0)
dmatest: dma0chan7-copy0: summary 5000 tests, 0 failures 183 iops 581 KB/s (0)
With this patch (no tasklet):
dmatest: dma0chan4-copy0: summary 5000 tests, 0 failures 199 iops 644 KB/s (0)
dmatest: dma0chan5-copy0: summary 5000 tests, 0 failures 199 iops 645 KB/s (0)
dmatest: dma0chan6-copy0: summary 5000 tests, 0 failures 199 iops 637 KB/s (0)
dmatest: dma0chan24-copy: summary 5000 tests, 0 failures 199 iops 638 KB/s (0)
dmatest: dma0chan16-copy: summary 5000 tests, 0 failures 199 iops 638 KB/s (0)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The for_each_sg() macro's last parameter is inteded to be used as counter.
We can use 'i' instead of 'j' within the loop for indexes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
During mem copy both src and dst position moves at the same pace. Check the
dst position for progress reporting.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In eDMA the events are directly mapped to a DMA channel (for example DMA
event 14 can only be handled by DMA channel 14). If the memcpy is enabled
on the eDMA, there is a possibility that the crossbar driver would assign
DMA event number already allocated in eDMA for memcpy. Furthermore the
eDMA can be shared with DSP in which case the crossbar driver should also
avoid mapping xbar events to DSP used event numbers (or channels).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The use of idr was nice, but it was a bit heavy and we did not need the
features it provides. Using simple bitmap to track allocated DMA channels
is adequate here and it will be easier to add support for reserving
channels later on.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Allow the crossbar driver to be used with the eDMA node with non legacy
binding.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
As we are now passing the filter data as pointers to the drivers,
we can take the final step and also pass the filter function the
same way. I'm keeping this change separate, as there it's less
obvious that this is a net win.
Upsides of this are:
- The ASoC drivers are completely independent from the DMA engine
implementation, which simplifies the Kconfig logic and in theory
allows the same sound drivers to be built in a kernel that supports
different kinds of dmaengine drivers.
- Consistency with other subsystems and drivers
On the other hand, we have a few downsides:
- The s3c24xx-dma driver now needs to be built-in for the ac97 platform
device to be instantiated on s3c2440.
- samsung_dmaengine_pcm_config cannot be marked 'const' any more
because the filter function pointer needs to be set at runtime.
This is safe as long we don't have multiple different DMA engines
in thet same system at runtime, but is nonetheless ugly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The dca_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
dma_addr_t may be defined as 32 or 64 bit depending on configuration,
so it cannot be printed using the normal format strings, as
gcc correctly warns:
drivers/dma/at_hdmac.c: In function 'atc_prep_dma_interleaved':
drivers/dma/at_hdmac.c:731:28: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]
This changes the format strings to use the special "%pad" format
string that prints a dma_addr_t, and changes the arguments so we
pass the address by reference as required.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
dma_addr_t may be defined as 32 or 64 bit depending on configuration,
so it cannot be printed using the normal format strings, as
gcc correctly warns:
drivers/dma/at_xdmac.c: In function 'at_xdmac_interleaved_queue_desc':
drivers/dma/at_xdmac.c:922:51: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]
This changes the format strings to use the special "%pad" format
string that prints a dma_addr_t, and changes the arguments so we
pass the address by reference as required.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The sdma_probe function will call sdma_event_remap, but sdma_event_remap
marked with the __init annotation which make the kbuild complains as the
following log:
WARNING: drivers/dma/built-in.o(.text+0x56fc): Section mismatch in reference
from the function sdma_probe() to the function .init.text:sdma_event_remap()
The function sdma_probe() references
the function __init sdma_event_remap().
This is often because sdma_probe lacks a __init
annotation or the annotation of sdma_event_remap is wrong.
Remove the __init annotation on sdma_event_remap to kill this build warning
Signed-off-by: Jason Liu <r64343@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Remove pre-3.0 channel status reads. 3.0 and later chansts register
is 64bit and can be read 64bit. This was clarified with the hardware
architects and since the driver now only support 3.0+ we don't need the
legacy support
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The current code uses bits 0-2 instead of 4-6 as the comment says.
Fixes: 633e42b8c546 ('dmaengine: edma: Get qDMA channel information from HW also')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
During the edma rework, a build error was introduced for the
case that CONFIG_OF is disabled:
drivers/built-in.o: In function `edma_tc_set_pm_state':
:(.text+0x43bf0): undefined reference to `of_find_device_by_node'
As the edma_tc_set_pm_state() function does nothing in case
we are running without OF, this adds an IS_ENABLED() check
that turns the function into an empty stub then and avoids the
link error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: ca304fa9bb76 ("ARM/dmaengine: edma: Public API to use private struct pointer")
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This patch adds support for the STM32 DMA controller.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
If the call to pm_runtime_get_sync() failed, Runtime PM was left
enabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
If CONFIG_PREEMPT=y:
Unable to handle kernel NULL pointer dereference at virtual address 00000014
pgd = c0003000
[00000014] *pgd=80000040004003, *pmd=00000000
Internal error: Oops: 206 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 17 Comm: kworker/0:1 Tainted: G W 4.3.0-rc3-koelsch-022
71-g705498fc5e6a5da8-dirty #1789
Hardware name: Generic R8A7791 (Flattened Device Tree)
Workqueue: pm pm_runtime_work
task: ef578e40 ti: ef57a000 task.ti: ef57a000
PC is at usb_dmac_chan_halt+0xc/0xc0
LR is at usb_dmac_runtime_suspend+0x28/0x38
pc : [<c023c880>] lr : [<c023c95c>] psr: 80000113
sp : ef57bdf8 ip : 00000008 fp : 00000003
r10: 00000008 r9 : c06ab928 r8 : ef49e810
r7 : 00000000 r6 : 000000ac r5 : ef770010 r4 : 00000000
r3 : 00000000 r2 : 8ffc2b84 r1 : 00000000 r0 : ef770010
Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 30c5307d Table: 40003000 DAC: fffffffd
Process kworker/0:1 (pid: 17, stack limit = 0xef57a210)
Stack: (0xef57bdf8 to 0xef57c000)
[...
[<c023c880>] (usb_dmac_chan_halt) from [<c023c95c>] (usb_dmac_runtime_suspend+0x28/0x38)
[<c023c95c>] (usb_dmac_runtime_suspend) from [<c027b25c>] (pm_genpd_runtime_suspend+0x74/0x23c)
This happens because usb_dmac_probe() calls pm_runtime_put() before
usb_dmac_chan_probe(), leading to the device being suspended before the
DMA channels are initialized, causing a NULL pointer dereference.
Move the call to pm_runtime_put() to the end of usb_dmac_probe() to fix
this.
Add a check to usb_dmac_runtime_suspend() to prevent the crash from
happening in the error path.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
As this driver provides a mechanism to reuse transfers, declare it in
its probe function.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In the current state, the capability of transfer reuse can neither be
set by a slave dmaengine driver, nor used by a client driver, because
the capability is not available to dma_get_slave_caps().
Fix this by adding a way to declare the capability.
Fixes: 272420214d26 ("dmaengine: Add DMA_CTRL_REUSE")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This patch attempts to enhance the case of a transfer submitted multiple
times, and where the cost of creating the descriptors chain is not
negligible.
This happens with big video buffers (several megabytes, ie. several
thousands of linked descriptors in one scatter-gather list). In these
cases, a video driver would want to do :
- tx = dmaengine_prep_slave_sg()
- dma_engine_submit(tx);
- dma_async_issue_pending()
- wait for video completion
- read video data (or not, skipping a frame is also possible)
- dma_engine_submit(tx)
=> here, the descriptors chain recalculation will take time
=> the dma coherent allocation over and over might create holes in
the dma pool, which is counter-productive.
- dma_async_issue_pending()
- etc ...
In order to cope with this case, virt-dma is modified to prevent freeing
the descriptors upon completion if DMA_CTRL_REUSE flag is set in the
transfer.
This patch is a respin of the former DMA_CTRL_ACK approach, which was
reverted due to a regression in audio drivers.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Implement the new device_synchronize() callback to allow proper
synchronization when stopping a channel. Since the driver already makes
sure that no new complete callbacks are scheduled after the
device_terminate_all() callback has been called, all left to do in the
device_synchronize() callback is to wait for all currently running complete
callbacks to finish.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Add a synchronize helper function for the virt-dma library. The function
makes sure that any scheduled descriptor complete callbacks have finished
running before the function returns.
This needs to be called by drivers using virt-dma in their
device_synchronize() callback. Depending on the driver additional
operations might be necessary in addition to calling vchan_synchronize() to
ensure proper synchronization.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The DMAengine API has a long standing race condition that is inherent to
the API itself. Calling dmaengine_terminate_all() is supposed to stop and
abort any pending or active transfers that have previously been submitted.
Unfortunately it is possible that this operation races against a currently
running (or with some drivers also scheduled) completion callback.
Since the API allows dmaengine_terminate_all() to be called from atomic
context as well as from within a completion callback it is not possible to
synchronize to the execution of the completion callback from within
dmaengine_terminate_all() itself.
This means that a user of the DMAengine API does not know when it is safe
to free resources used in the completion callback, which can result in a
use-after-free race condition.
This patch addresses the issue by introducing an explicit synchronization
primitive to the DMAengine API called dmaengine_synchronize().
The existing dmaengine_terminate_all() is deprecated in favor of
dmaengine_terminate_sync() and dmaengine_terminate_async(). The former
aborts all pending and active transfers and synchronizes to the current
context, meaning it will wait until all running completion callbacks have
finished. This means it is only possible to call this function from
non-atomic context. The later function does not synchronize, but can still
be used in atomic context or from within a complete callback. It has to be
followed up by dmaengine_synchronize() before a client can free the
resources used in a completion callback.
In addition to this the semantics of the device_terminate_all() callback
are slightly relaxed by this patch. It is now OK for a driver to only
schedule the termination of the active transfer, but does not necessarily
have to wait until the DMA controller has completely stopped. The driver
must ensure though that the controller has stopped and no longer accesses
any memory when the device_synchronize() callback returns.
This was in part done since most drivers do not pay attention to this
anyway at the moment and to emphasize that this needs to be done when the
device_synchronize() callback is implemented. But it also helps with
implementing support for devices where stopping the controller can require
operations that may sleep.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Pull dmaengine updates from Vinod Koul:
"This time we have a very typical update which is mostly fixes and
updates to drivers and no new drivers.
- the biggest change is coming from Peter for edma cleanup which even
caused some last minute regression, things seem settled now
- idma64 and dw updates
- iotdma updates
- module autoload fixes for various drivers
- scatter gather support for hdmac"
* tag 'dmaengine-4.4-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (77 commits)
dmaengine: edma: Add dummy driver skeleton for edma3-tptc
Revert "ARM: DTS: am33xx: Use the new DT bindings for the eDMA3"
Revert "ARM: DTS: am437x: Use the new DT bindings for the eDMA3"
dmaengine: dw: some Intel devices has no memcpy support
dmaengine: dw: platform: provide platform data for Intel
dmaengine: dw: don't override platform data with autocfg
dmaengine: hdmac: Add scatter-gathered memset support
dmaengine: hdmac: factorise memset descriptor allocation
dmaengine: virt-dma: Fix kernel-doc annotations
ARM: DTS: am437x: Use the new DT bindings for the eDMA3
ARM: DTS: am33xx: Use the new DT bindings for the eDMA3
dmaengine: edma: New device tree binding
dmaengine: Kconfig: edma: Select TI_DMA_CROSSBAR in case of ARCH_OMAP
dmaengine: ti-dma-crossbar: Add support for crossbar on AM33xx/AM43xx
dmaengine: edma: Merge the of parsing functions
dmaengine: edma: Do not allocate memory for edma_rsv_info in case of DT boot
dmaengine: edma: Refactor the dma device and channel struct initialization
dmaengine: edma: Get qDMA channel information from HW also
dmaengine: edma: Merge map_dmach_to_queue into assign_channel_eventq
dmaengine: edma: Correct PaRAM access function names (_parm_ to _param_)
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver update for 4.4-rc1. Lots of
different driver and subsystem updates, hwtracing being the largest
with the addition of some new platforms that are now supported. Full
details in the shortlog.
All of these have been in linux-next for a long time with no reported
issues"
* tag 'char-misc-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (181 commits)
fpga: socfpga: Fix check of return value of devm_request_irq
lkdtm: fix ACCESS_USERSPACE test
mcb: Destroy IDA on module unload
mcb: Do not return zero on error path in mcb_pci_probe()
mei: bus: set the device name before running fixup
mei: bus: use correct lock ordering
mei: Fix debugfs filename in error output
char: ipmi: ipmi_ssif: Replace timeval with timespec64
fpga: zynq-fpga: Fix issue with drvdata being overwritten.
fpga manager: remove unnecessary null pointer checks
fpga manager: ensure lifetime with of_fpga_mgr_get
fpga: zynq-fpga: Change fw format to handle bin instead of bit.
fpga: zynq-fpga: Fix unbalanced clock handling
misc: sram: partition base address belongs to __iomem space
coresight: etm3x: adding documentation for sysFS's cpu interface
vme: 8-bit status/id takes 256 values, not 255
fpga manager: Adding FPGA Manager support for Xilinx Zynq 7000
ARM: zynq: dt: Updated devicetree for Zynq 7000 platform.
ARM: dt: fpga: Added binding docs for Xilinx Zynq FPGA manager.
ver_linux: proc/modules, limit text processing to 'sed'
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big tty and serial driver update for 4.4-rc1.
Lots of serial driver updates and a few small tty core changes. Full
details in the shortlog.
All of these have been in linux-next for a while"
* tag 'tty-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (148 commits)
tty: Use unbound workqueue for all input workers
tty: Abstract tty buffer work
tty: Prevent tty teardown during tty_write_message()
tty: core: Use correct spinlock flavor in tiocspgrp()
tty: Combine SIGTTOU/SIGTTIN handling
serial: amba-pl011: fix incorrect integer size in pl011_fifo_to_tty()
ttyFDC: Fix build problems due to use of module_{init,exit}
tty: remove unneeded return statement
serial: 8250_mid: add support for DMA engine handling from UART MMIO
dmaengine: hsu: remove platform data
dmaengine: hsu: introduce stubs for the exported functions
dmaengine: hsu: make the UART driver in control of selecting this driver
serial: fix mctrl helper functions
serial: 8250_pci: Intel MID UART support to its own driver
serial: fsl_lpuart: add earlycon support
tty: disable unbind for old 74xx based serial/mpsc console port
serial: pl011: Spelling s/clocks-names/clock-names/
n_tty: Remove reader wakeups for TTY_BREAK/TTY_PARITY chars
tty: synclink, fix indentation
serial: at91, fix rs485 properties
...
|
|
The eDMA3 TPTC does not need any software configuration, but it is a
separate IP block in the SoC. In order the omap hwmod core to be able to
handle the TPTC resources correctly in regards of PM we need to have a
driver loaded for it.
This patch will add a dummy driver skeleton without probe or remove
callbacks provided.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reported-by: Olof Johansson <olof@lixom.net>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
|
