| Age | Commit message (Collapse) | Author |
|---|
|
There is no need to print that the driver has been initialized
or removed, so remove such messages.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Since commit d078cd1b4185 ("dmaengine: imx-sdma: Add imx6sx platform
support") we get this message on every boot on mx6q:
imx-sdma 20ec000.sdma: no event needs to be remapped
, which is not very helpful.
Move the message to debug level instead.
Cc: Zidan Wang <zidan.wang@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This is needed due to the duplicated iommu stuff to help with the merge
and to prevent future issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The L3 throughput can be higher than expected when packed access
is not enabled. The ratio depends on the number of bytes in a
transaction and the EMIF interface width.
The throughput was measured for the following settings/cases:
* Case 1: Burst size of 64 bytes, packed access disabled
* Case 2: Burst size of 64 bytes, packed access enabled
* Case 3: Burst disabled, packed access disabled
Throughput measurements were done during McASP-based audio
playback on the Jacinto6 EVM using the omapconf tool [1]:
$ omapconf trace bw -m sdma_rd
---------------------------------------------------------
Throughput (MB/s)
Audio parameters Case 1 Case 2 Case 3
---------------------------------------------------------
44.1kHz, 16-bits, stereo 1.41 0.18 1.41
44.1kHz, 32-bits, stereo 1.41 0.35 1.41
44.1kHz, 16-bits, 4-chan 2.82 0.35 2.82
44.1kHz, 16-bits, 6-chan 4.23 0.53 4.23
44.1kHz, 16-bits, 8-chan 5.64 0.71 5.64
---------------------------------------------------------
From above measurements, case 2 is the only one that delivers
the expected throughput for the given audio parameters. For
that reason, the packed accesses are now enabled.
It's worth to mention that packed accesses cannot be enabled
for all addressing modes. In cyclic transfers, it can be
enabled in the source for MEM_TO_DEV and in dest for DEV_TO_MEM,
as they use post-increment mode which supports packed accesses.
Peter Ujfalusi:
From the TRM regarding to this:
"NOTE: Except in the constant addressing mode, the source or
destination must be specified as packed for burst transactions
to occur."
So w/o the packed setting the burst on the MEM side was not
enabled, this explains the numbers.
[1] https://github.com/omapconf/omapconf
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The MIC X100 DMA engine has a special status descriptor which writes
an 8 byte value to a destination location. This is used to signal
completion of all DMA descriptors prior to the status descriptor.
This patch add a new DMA engine API which enables updating a
destination address with an 8 byte immediate data value.
Reviewed-by: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Lawrynowicz, Jacek <jacek.lawrynowicz@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Siva Yerramreddy <yshivakrishna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"This contains fixes spread throughout the drivers, and also fixes one
more instance of privatecnt in dmaengine.
Driver fixes summary:
- bunch of pxa_dma fixes for reuse of descriptor issue, residue and
no-requestor
- odd fixes in xgene, idma, sun4i and zxdma
- at_xdmac fixes for cleaning descriptor and block addr mode"
* tag 'dmaengine-fix-4.3-rc4' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: pxa_dma: fix residue corner case
dmaengine: pxa_dma: fix the no-requestor case
dmaengine: zxdma: Fix off-by-one for testing valid pchan request
dmaengine: at_xdmac: clean used descriptor
dmaengine: at_xdmac: change block increment addressing mode
dmaengine: dw: properly read DWC_PARAMS register
dmaengine: xgene-dma: Fix overwritting DMA tx ring
dmaengine: fix balance of privatecnt
dmaengine: sun4i: fix unsafe list iteration
dmaengine: idma64: improve residue estimation
dmaengine: xgene-dma: fix handling xgene_dma_get_ring_size result
dmaengine: pxa_dma: fix initial list move
|
|
A very tiny temporal window exists in the residue calculation where :
- upon entering residue calculation, the transfer is ongoing
- when reading the current transfer pointer, it just changed to
the "finisher/linker" descriptor
In this case, the residue returned is the whole transfer length instead
of 0. Fix it.
This appears almost in one extreme case, where the driver is used
by older clients which inquire for residue in interrupt context, such
as the smsc91x ethernet driver, in a tight loop :
interrupt_handler()
dmaengine_submit()
do {
dmaengine_tx_status()
} while (residue > 0 || status != DMA_ERROR)
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
A very small number of devices don't use the flow control offered by
requestor lines. In these specific cases, the pxa dma driver should be
aware of that and not try to use a requestor line.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The valid pchan range is 0 ~ d->dma_requests - 1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In interleaved mode, when numf > 1, we have only one descriptor for the
transfer but this descriptor has to be added to the descs_list. If not,
when doing remove_xfer, the descriptor won't be put back in the
free_descs_list.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Handle 'numf > 1' case for interleaved mode.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
When putting back a descriptor to the free descs list, some fields are
not set to 0, it can cause bugs if someone uses it without having this
in mind.
Descriptor are not put back one by one so it is easier to clean
descriptors when we request them.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@vger.kernel.org #4.2
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The addressing mode we were using was not only incrementing the address at
each microblock, but also at each data boundary, which was severely slowing
the transfer, without any benefit since we were not using the data stride.
Switch to the micro block increment only in order to get back to an
acceptable performance level.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 6007ccb57744 ("dmaengine: xdmac: Add interleaved transfer support")
Cc: stable@vger.kernel.org #4.2
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Fix the call to memset in this driver
[linux-4.2-next-20150911/drivers/dma/zx296702_dma.c:444]: (warning)
memset() called to fill 0 bytes of 'ds'.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Instead of hardconding a platform data for dw_dmac let's use it's own
autoconfiguration feature. Thus, remove hardcoded values.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
We replace __fls() by __ffs() since we have to find a *minimum* data width that
satisfies both source and destination.
While here, rename dwc_fast_fls() to dwc_fast_ffs() which it really is.
Fixes: 4c2d56c574db (dw_dmac: introduce dwc_fast_fls())
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In case we have less than maximum allowed channels (8) and autoconfiguration is
enabled the DWC_PARAMS read is wrong because it uses different arithmetic to
what is needed for channel priority setup.
Re-do the caclulations properly. This now works on AVR32 board well.
Fixes: fed2574b3c9f (dw_dmac: introduce software emulation of LLP transfers)
Cc: yitian.bu@tangramtek.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This patch fixes an over flow issue with the TX ring descriptor. Each
descriptor is 32B in size and an operation requires 2 of these
descriptors.
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
dma_release_channel() decrements privatecnt counter and almost all dma_get*
function increments it with the exception of dma_get_slave_channel().
In most cases this does not cause issue since normally the channel is not
requested and released, but if a driver requests DMA channel via
dma_get_slave_channel() and releases the channel the privatecnt will be
unbalanced and this will prevent for example getting channel for memcpy.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Get pointer to the struct acpi_device by using ACPI_COMPANION() macro. This
is more efficient than using ACPI_HANDLE() and acpi_bus_get_device().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Currently, sun4i_dma_free_contract iterates over lists and frees memory
as it goes through them, causing reads to recently freed memory to
be performed. Fix this by using the safe version of the iterator, so
freed memory is not referenced at all.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
in edma_callback, driver was doing redundant check for desc, so remove that
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
There are already helper functions to do 64-bit I/O on 32-bit machines, thus we
don't need to reinvent the wheel. In our case we can't use readq() / writeq()
even on 64-bit kernel since there is a hardware limitation (OCP bus is a 32-bit
bus).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Accordingly to the documentation the CH_DRAIN bit enforses single bursts when
channel is going to be suspended. This, in case when channel will be resumed,
makes data to flow in non-optimal mode until DMA returns to full burst mode.
The fix differentiates pause / resume cycle from pause / terminate and sets
CH_DRAIN bit accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This patch fixes a comment where DesignWare is wrongly mentioned. There is no
functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
We use a pattern
x = min_t(u32, <LOG2_CONSTANT>, __ffs(expr));
There is no need to use min_t() since we can replace it by
x = __ffs(expr | <2^LOG2_CONST>);
and moreover guarantee that argument of __ffs() will be not zero.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
We replace __fls() by __ffs() since we have to find a *minimum* data width that
satisfies both source and destination.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The residue calculation may provide a wrong estimation when the transfer is
started. There are possible scenarios we have to separate:
1) the transfer is not started yet; residue is equal to the total
length;
2) the transfer is just started (first chunk is ongoing); residue is
equal to the total length without already transfered bytes;
3) the transfer is ongoing and we already sent few chunks of data;
residue is equal to the total length without fully transfered chunks
and already sent bytes.
Mistakenly the calculation in cases 2) and 3) was done in the similar way and
the result is equal to -bytes that have been transfered, i.e. quite big since
size_t type can't keep negative values.
Rewrite the calculation algorithm to be one pass and have a correct result.
Besides above in case user asks for a status of the active DMA descriptor
without pausing an ongoing transfer the residue will be estimated based on the
register value, though it's still racy. Since the transfer is active the value
is continuously being changed. Here we have to read two registers at a time. To
minimize an error make those reads close to each other.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Since the commit to have an allocated list of virtual descriptors was
reverted, the pxa_dma driver is broken, as it assumes the descriptor is
placed on the allocated list upon allocation.
Fix the issue in pxa_dma by making an allocated virtual descriptor a
singleton.
Fixes: 8c8fe97b2b8a ("Revert "dmaengine: virt-dma: don't always free descriptor upon completion"")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The current implementation hard codes the two supported channels so that
"tx" is always 0 and "rx" is always 1. This is because there has been no
suitable way in ACPI to name resources.
With _DSD device properties we can finally do this:
Device (SPI1) {
Name (_CRS, ResourceTemplate () {
...
FixedDMA (0x0000, 0x0000, Width32bit)
FixedDMA (0x0001, 0x0001, Width32bit)
})
Name (_DSD, Package () {
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () {"dma-names", Package () {"tx", "rx"}}
},
})
}
The names "tx" and "rx" now provide index of the FixedDMA resource in
question.
Modify acpi_dma_request_slave_chan_by_name() so that it looks for
"dma-names" property first and only then fall back using hardcoded indices.
The DT "dma-names" binding that we reuse for ACPI is documented in
Documentation/devicetree/bindings/dma/dma.txt.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
the symbol CONFIG_IDMA64 should rather be CONFIG_INTEL_IDMA64 to conform to
rest of the intel dmaengine drivers. This was found after sorting the
entries and trying to place this odd one
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Remove unneeded NULL test.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ expression x; @@
-if (x != NULL)
\(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Adding AER handlers in order to handle any PCIe errors.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The ioatdma needs to be queisced and block all additional op submission
during reboots. When NET_DMA was used, this caused issue as ops were still
being sent to ioatdma during reboots even though PCI BME has been turned
off. Even though NET_DMA has been deprecated, we need to prevent similar
situations. The shutdown handler should address that.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
We should use shiny new dma_pool_zalloc instead of
dma_pool_alloc/memset
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
|
|
Pull dmaengine updates from Vinod Koul:
"This time we have aded a new capability for scatter-gathered memset
using dmaengine APIs. This is supported in xdmac & hdmac drivers
We have added support for reusing descriptors for examples like video
buffers etc. Driver will follow
The behaviour of descriptor ack has been clarified and documented
New devices added are:
- dma controller in sun[457]i SoCs
- lpc18xx dmamux
- ZTE ZX296702 dma controller
- Analog Devices AXI-DMAC DMA controller
- eDMA support for dma-crossbar
- imx6sx support in imx-sdma driver
- imx-sdma device to device support
Other:
- jz4780 fixes
- ioatdma large refactor and cleanup for removal of ioat v1 and v2
which is deprecated and fixes
- ACPI support in X-Gene DMA engine driver
- ipu irq fixes
- mvxor fixes
- minor fixes spread thru drivers"
[ The Kconfig and Makefile entries got re-sorted alphabetically, and I
handled the conflict with the new Intel integrated IDMA driver by
slightly mis-sorting it on purpose: "IDMA64" got sorted after "IMX" in
order to keep the Intel entries together. I think it might be a good
idea to just rename the IDMA64 config entry to INTEL_IDMA64 to make
the sorting be a true sort, not this mismash.
Also, this merge disables the COMPILE_TEST for the sun4i DMA
controller, because it does not compile cleanly at all. - Linus ]
* tag 'dmaengine-4.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (89 commits)
dmaengine: ioatdma: add Broadwell EP ioatdma PCI dev IDs
dmaengine :ipu: change ipu_irq_handler() to remove compile warning
dmaengine: ioatdma: Fix variable array length
dmaengine: ioatdma: fix sparse "error" with prep lock
dmaengine: hdmac: Add memset capabilities
dmaengine: sort the sh Makefile
dmaengine: sort the sh Kconfig
dmaengine: sort the dw Kconfig
dmaengine: sort the Kconfig
dmaengine: sort the makefile
drivers/dma: make mv_xor.c driver explicitly non-modular
dmaengine: Add support for the Analog Devices AXI-DMAC DMA controller
devicetree: Add bindings documentation for Analog Devices AXI-DMAC
dmaengine: xgene-dma: Fix the lock to allow client for further submission of requests
dmaengine: ioatdma: fix coccinelle warning
dmaengine: ioatdma: fix zero day warning on incompatible pointer type
dmaengine: tegra-apb: Simplify locking for device using global pause
dmaengine: tegra-apb: Remove unnecessary return statements and variables
dmaengine: tegra-apb: Avoid unnecessary channel base address calculation
dmaengine: tegra-apb: Remove unused variables
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"From the number of commits perspective, the biggest items are ACPICA
and cpufreq changes with the latter taking the lead (over 50 commits).
On the cpufreq front, there are many cleanups and minor fixes in the
core and governors, driver updates etc. We also have a new cpufreq
driver for Mediatek MT8173 chips.
ACPICA mostly updates its debug infrastructure and adds a number of
fixes and cleanups for a good measure.
The Operating Performance Points (OPP) framework is updated with new
DT bindings and support for them among other things.
We have a few updates of the generic power domains framework and a
reorganization of the ACPI device enumeration code and bus type
operations.
And a lot of fixes and cleanups all over.
Included is one branch from the MFD tree as it contains some
PM-related driver core and ACPI PM changes a few other commits are
based on.
Specifics:
- ACPICA update to upstream revision 20150818 including method
tracing extensions to allow more in-depth AML debugging in the
kernel and a number of assorted fixes and cleanups (Bob Moore, Lv
Zheng, Markus Elfring).
- ACPI sysfs code updates and a documentation update related to AML
method tracing (Lv Zheng).
- ACPI EC driver fix related to serialized evaluations of _Qxx
methods and ACPI tools updates allowing the EC userspace tool to be
built from the kernel source (Lv Zheng).
- ACPI processor driver updates preparing it for future introduction
of CPPC support and ACPI PCC mailbox driver updates (Ashwin
Chaugule).
- ACPI interrupts enumeration fix for a regression related to the
handling of IRQ attribute conflicts between MADT and the ACPI
namespace (Jiang Liu).
- Fixes related to ACPI device PM (Mika Westerberg, Srinidhi
Kasagar).
- ACPI device registration code reorganization to separate the
sysfs-related code and bus type operations from the rest (Rafael J
Wysocki).
- Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause,
Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss).
- ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups (Pan
Xinhui, Rafael J Wysocki).
- cpufreq core cleanups on top of the previous changes allowing it to
preseve its sysfs directories over system suspend/resume (Viresh
Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior).
- cpufreq fixes and cleanups related to governors (Viresh Kumar).
- cpufreq updates (core and the cpufreq-dt driver) related to the
turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz).
- New DT bindings for Operating Performance Points (OPP), support for
them in the OPP framework and in the cpufreq-dt driver plus related
OPP framework fixes and cleanups (Viresh Kumar).
- cpufreq powernv driver updates (Shilpasri G Bhat).
- New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen).
- Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups
and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean).
- intel_pstate driver updates including Skylake-S support, support
for enabling HW P-states per CPU and an additional vendor bypass
list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao).
- cpuidle core fixes related to the handling of coupled idle states
(Xunlei Pang).
- intel_idle driver updates including Skylake Client support and
support for freeze-mode-specific idle states (Len Brown).
- Driver core updates related to power management (Andy Shevchenko,
Rafael J Wysocki).
- Generic power domains framework fixes and cleanups (Jon Hunter,
Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson).
- Device PM QoS framework update to allow the latency tolerance
setting to be exposed to user space via sysfs (Mika Westerberg).
- devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect
exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas).
- System sleep support updates (Alan Stern, Len Brown, SungEun Kim).
- rockchip-io AVS support updates (Heiko Stuebner).
- PM core clocks support fixup (Colin Ian King).
- Power capping RAPL driver update including support for Skylake H/S
and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi).
- Generic device properties framework fixes related to the handling
of static (driver-provided) property sets (Andy Shevchenko).
- turbostat and cpupower updates (Len Brown, Shilpasri G Bhat,
Shreyas B Prabhu)"
* tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (180 commits)
cpufreq: speedstep-lib: Use monotonic clock
cpufreq: powernv: Increase the verbosity of OCC console messages
cpufreq: sfi: use kmemdup rather than duplicating its implementation
cpufreq: drop !cpufreq_driver check from cpufreq_parse_governor()
cpufreq: rename cpufreq_real_policy as cpufreq_user_policy
cpufreq: remove redundant 'policy' field from user_policy
cpufreq: remove redundant 'governor' field from user_policy
cpufreq: update user_policy.* on success
cpufreq: use memcpy() to copy policy
cpufreq: remove redundant CPUFREQ_INCOMPATIBLE notifier event
cpufreq: mediatek: Add MT8173 cpufreq driver
dt-bindings: mediatek: Add MT8173 CPU DVFS clock bindings
PM / Domains: Fix typo in description of genpd_dev_pm_detach()
PM / Domains: Remove unusable governor dummies
PM / Domains: Make pm_genpd_init() available to modules
PM / domains: Align column headers and data in pm_genpd_summary output
powercap / RAPL: disable the 2nd power limit properly
tools: cpupower: Fix error when running cpupower monitor
PM / OPP: Drop unlikely before IS_ERR(_OR_NULL)
PM / OPP: Fix static checker warning (broken 64bit big endian systems)
...
|
|
* acpi-pm:
ACPI / bus: Move duplicate code to a separate new function
mfd: Add support for Intel Sunrisepoint LPSS devices
dmaengine: add a driver for Intel integrated DMA 64-bit
mfd: make mfd_remove_devices() iterate in reverse order
driver core: implement device_for_each_child_reverse()
klist: implement klist_prev()
Driver core: wakeup the parent device before trying probe
ACPI / PM: Attach ACPI power domain only once
PM / QoS: Make it possible to expose device latency tolerance to userspace
ACPI / PM: Update the copyright notice and description of power.c
|
|
Adding the Broadwell Xeon ioatdma PCI device IDs and
related bits. This is still IOATDMA 3.2 based hw.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Change ipu_irq_handler() to avoid gcc warning:
drivers/dma/ipu/ipu_irq.c:305:4: warning: 'irq' may be used
uninitialized in this function [-Wmaybe-uninitialized]
generic_handle_irq(irq);
Signed-off-by: yalin wang <yalin.wang2010@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Sparse reported:
drivers/dma/ioat/prep.c:637:27: sparse: Variable length array is used.
Assigning a static value for the array.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The prep lock gets acquired in ioat_check_space_lock and released in
ioat_tx_submit_unlock. Setting the annotations so sparse does not freak out.
drivers/dma/ioat/dma.c:273:30: sparse: context imbalance in 'ioat_tx_submit_unlock' - unexpected unlock
drivers/dma/ioat/dma.c:476:5: sparse: context imbalance in 'ioat_check_space_lock' - wrong count at exit
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
