| Age | Commit message (Collapse) | Author |
|---|
|
load_count/total_count are reset by devfreq_event_get_event(), so
remove the redundant code in exynos_nocp_get_event().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
[ rjw: Subject/changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This driver uses devm_regmap_init_mmio(), so select REGMAP_MMIO to avoid
build failure.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Current code uses devm_regulator_get() in .probe so a regulator_put() will
be automatically called when unload the module. Remove the explictly
regulator_put() call and then we can also remove rk3399_dmcfreq_remove().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The newly added ARM_RK3399_DMC_DEVFREQ driver requires the
DEVFREQ_EVENT_ROCKCHIP_DFI driver and tries to turn that on through
a 'select' statement, and that in turn has a dependency on
PM_DEVFREQ_EVENT, which may be disabled here:
warning: (ARM_RK3399_DMC_DEVFREQ) selects DEVFREQ_EVENT_ROCKCHIP_DFI which has unmet direct dependencies (PM_DEVFREQ && PM_DEVFREQ_EVENT && ARCH_ROCKCHIP)
We probably want a 'depends on' here, but other drivers use 'select'
too, so for consistency I'm doing the same.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 5a893e31a636 (PM / devfreq: rockchip: add devfreq driver for rk3399 dmc)
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This reverts the Tegra part of commit 797da5598f3a (PM / devfreq: Add
COMPILE_TEST for build coverage) that introduced a build failute in
in linux-next.
[ rjw: Changelog ]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
base on dfi result, we do ddr frequency scaling, register
dmc driver to devfreq framework, and use simple-ondemand
policy.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: MyngJoo Ham <myngjoo.ham@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
on rk3399 platform, there is dfi conroller can monitor
ddr load, base on this result, we can do ddr freqency
scaling.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
Use tab rather than space to indent, and tab + two spaces to indent
help message.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
The SoC-specific devfreq and devfreq-event drivers can be build tested
on all architectures.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
for_each_child_of_node() performs an of_node_put() on each iteration, so
putting an of_node_put() before a continue results in a double put.
Generated by: scripts/coccinelle/iterators/device_node_continue.cocci
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
[Commit updated to fix an error by MyungJoo]
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
iounmap() needs to be called in case of memory allocation
(for devfreq-event devices) failure. Fix it.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
In case of exynos_bus_parse_of() failure the code shouldn't
try to remove the OPP table and disable+unprepare bus->clk
as it has been already handled in exynos_bus_parse_of().
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
The Kconfig currently controlling compilation of this code is:
config DEVFREQ_EVENT_EXYNOS_PPMU
bool "EXYNOS PPMU (Platform Performance Monitoring Unit) DEVFREQ event Driver"
...meaning that it currently is not being built as a module by anyone.
Rather than rip out the existing modular code, Chanwoo indicated
that he'd rather see the driver offered as tristate.
I don't have the hardware for runtime validation, so this change
is only validated for compile and modpost.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
The Kconfig currently controlling compilation of this code is:
event/Kconfig:config DEVFREQ_EVENT_EXYNOS_NOCP
event/Kconfig: bool "EXYNOS NoC (Network On Chip) Probe DEVFREQ event Driver"
...meaning that it currently is not being built as a module by anyone.
Rather than rip out the existing modular code, Chanwoo indicated
that he'd rather see the driver offered as tristate.
I don't have the hardware for runtime validation, so this change
is only validated for compile and modpost.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
The Kconfig currently controlling compilation of this code is:
devfreq/Kconfig:config ARM_EXYNOS_BUS_DEVFREQ
devfreq/Kconfig: bool "ARM EXYNOS Generic Memory Bus DEVFREQ Driver"
...meaning that it currently is not being built as a module by anyone.
Rather than rip out the existing modular code, Chanwoo indicated
that he'd rather see the driver offered as tristate.
I don't have the hardware for runtime validation, so this change
is only validated for compile and modpost.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
The Kconfig currently controlling compilation of this code is:
menuconfig PM_DEVFREQ_EVENT
bool "DEVFREQ-Event device Support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
This code wasn't using module_init, so we don't need to be concerned
with altering the initcall level here.
We don't replace module.h with init.h since the file already has that.
But we do add export.h since this file does export some symbols.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
The Kconfig currently controlling compilation of this code is:
menuconfig PM_DEVFREQ
bool "Generic Dynamic Voltage and Frequency Scaling (DVFS) support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
This code wasn't using module_init, so we don't need to be concerned
with altering the initcall level here.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We don't replace module.h with init.h since the file already has that.
But we do add export.h since this file does export some symbols.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
This patch sends the DEVFREQ_POSTCHANGE notification when
devfreq->profile->targer() is failed. The PRECHANGE/POSTCHANGE
should be paired.
Fixes: 0fe3a66410a3 (PM / devfreq: Add new DEVFREQ_TRANSITION_NOTIFIER notifier)
Reported-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some systems need current frequency from last_status for calculation
but it is zeroed during initialization. When the device starts there is
no history, but we can assume that the last frequency was the
same as the initial frequency (which is also used in 'previous_freq').
The log shows the result of this misinterpreted value.
[ 2.042847] ... Failed to get voltage for frequency 0: -34
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
Smatch complains because platform_get_resource() returns NULL on error
and not an error pointer so the check is wrong. Julia Lawall pointed
out that normally we don't check these, because devm_ioremap_resource()
has a check for NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
When device_register() returns with error, it has already
done put_device() on the input device pointer.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
1295 */
1296 void device_unregister(struct device *dev)
1297 {
1298 pr_debug("device: '%s': %s\n", dev_name(dev), __func__);
1299 device_del(dev);
1300 put_device(dev);
1301 }
1302 EXPORT_SYMBOL_GPL(device_unregister);
1303
device_unregister is called put_device, there is no need to call
put_device(&devfreq->dev) again.
Signed-off-by: Cai Zhiyong <caizhiyong@huawei.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
device_unregister() calls kfree already.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
devm_kzalloc of devfreq's statistics data structure has been
using its parent device as the dev allocated for.
If a device's devfreq is disabled in run-time,
such allocated memory won't be freed.
Desginating more precisely with the devfreq device
pointer fixes the issue.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
- Typo in comments fixed
- Unnecessary return statement removed
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
This patch use the phandle to find the instance of devfreq-event device in
Device Tree when calling the devfreq_event_get_edev_by_phandle() because there
is two type devfreq-event devices as following:
First case, exynos-ppmu.c driver provides the maximum four event of each PPMU.
So, when getting the instance of devfreq-event device, using the unique name of
struct devfreq_event_desc.
Second case, exynos-nocp.c driver provide the only one event of each NoC Probe
device. So, when getting the instance of devfreq-event device, using the
phandle of each NoC probe device.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
This patch adds NoC (Network on Chip) Probe driver which provides
the primitive values to get the performance data. The packets that the Network
on Chip (NoC) probes detects are transported over the network infrastructure.
Exynos542x bus has multiple NoC probes to provide bandwidth information about
behavior of the SoC that you can use while analyzing system performance.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
This patch removes the unused exynos4/5 busfreq driver. Instead,
generic exynos-bus frequency driver support the all Exynos SoCs.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
passive governor
This patch adds the support of bus frequency feature for sub-blocks which share
the one power line. If each bus depends on the power line, each bus is not able
to change the voltage by oneself. To optimize the power-consumption on runtime,
some buses using the same power line should change the source clock and
regulator at the same time. So, this patch uses the passive governor to support
the bus frequency for all buses which sharing the one power line.
For example,
Exynos3250 include the two power line for AXI buses as following:
: VDD_MIF : MIF (Memory Interface) provide the DMC (Dynamic Memory Controller)
with the power (regulator).
: VDD_INT : INT (Internal) provide the various sub-blocks with the power
(regulator).
Each bus is included in as follwoing block. In the case of VDD_MIF, only DMC bus
use the power line. So, there is no any depencency between buese. But, in the
case of VDD_INT, various buses share the one power line of VDD_INT. We need to
make the depenency between buses. When using passive governor, there is no
problem to support the bus frequency as DVFS for all buses. One bus should be
operated as the parent bus device which gathering the current load of INT block
and then decides the new frequency with some governors except of passive
governor. After deciding the new frequency by the parent bus device, the rest
bus devices will change the each source clock according to new frequency of the
parent bus device.
- MIF (Memory Interface) block
: VDD_MIF |--- DMC
- INT (Internal) block
: VDD_INT |--- LEFTBUS (parent)
|--- PERIL
|--- MFC
|--- G3D
|--- RIGHTBUS
|--- FSYS
|--- LCD0
|--- PERIR
|--- ISP
|--- CAM
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[tjakobi: Reported debugfs error during booting and cw00.choi fix it.]
Reported-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
This patch adds the new passive governor for DEVFREQ framework. The following
governors are already present and used for DVFS (Dynamic Voltage and Frequency
Scaling) drivers. The following governors are independently used for one device
driver which don't give the influence to other device drviers and also don't
receive the effect from other device drivers.
- ondemand / performance / powersave / userspace
The passive governor depends on operation of parent driver with specific
governos extremely and is not able to decide the new frequency by oneself.
According to the decided new frequency of parent driver with governor,
the passive governor uses it to decide the appropriate frequency for own
device driver. The passive governor must need the following information
from device tree:
- the source clock and OPP tables
- the instance of parent device
For exameple,
there are one more devfreq device drivers which need to change their source
clock according to their utilization on runtime. But, they share the same
power line (e.g., regulator). So, specific device driver is operated as parent
with ondemand governor and then the rest device driver with passive governor
is influenced by parent device.
Suggested-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[tjakobi: Reported RCU locking issue and cw00.choi fix it]
Reported-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
[linux.amoon: Reported possible recursive locking and cw00.choi fix it]
Reported-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
This patch adds the new DEVFREQ_TRANSITION_NOTIFIER notifier to send
the notification when the frequency of device is changed.
This notifier has two state as following:
- DEVFREQ_PRECHANGE : Notify it before chaning the frequency of device
- DEVFREQ_POSTCHANGE : Notify it after changed the frequency of device
And this patch adds the resourced-managed function to release the resource
automatically when error happen.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
This patch adds the new devfreq_get_devfreq_by_phandle() OF helper function
which can find the instance of devfreq device by using phandle ("devfreq").
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
This patch adds the generic exynos bus frequency driver for AMBA AXI bus
of sub-blocks in exynos SoC with DEVFREQ framework. The Samsung Exynos SoC
have the common architecture for bus between DRAM and sub-blocks in SoC.
This driver can support the generic bus frequency driver for Exynos SoCs.
In devicetree, Each bus block has a bus clock, regulator, operation-point
and devfreq-event devices which measure the utilization of each bus block.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
As per the documentation of the devfreq_dev_profile.target callback, set
the freq argument to the new frequency before returning.
This caused endless messages like this after recent changes in the core:
devfreq 6000c800.actmon: Couldn't update frequency transition information.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reported-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
Before this patch for a device without statistics support,
$ cat trans_stat
From : To
: time(ms)
Total transitions : 0
$
After this patch applied for such a device,
$ cat trans_stat
Not Supported.
$
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
This patch modifies the indentation of 'trans_stat' sysfs to improve readability.
The 1GHz is 1000,000,000. So it needs the least 10 position to show the GHz unit.
- Before apply this patch,
-sh-3.2# cat trans_stat
From : To
:50000000100000000133000000200000000400000000 time(ms)
*50000000: 0 0 0 0 7 1817635
100000000: 4 0 0 0 4 1590
133000000: 1 4 0 0 7 975
200000000: 2 2 7 0 1 2655
400000000: 0 2 5 12 0 1860
Total transition : 58
- After apply this patch,
-sh-3.2# cat trans_stat
From : To
: 50000000 100000000 133000000 200000000 400000000 time(ms)
* 50000000: 0 0 0 0 7 14405
100000000: 4 0 0 0 3 2015
133000000: 2 3 0 0 7 1020
200000000: 1 2 7 0 0 2970
400000000: 0 2 5 10 0 1575
Total transition : 53
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
This patch initialize the freq_table array of each devfreq device by using
the devfreq_set_freq_table(). If freq_table is NULL, the devfreq framework
is not able to support the frequency transtion information through sysfs.
The OPP core uses the integer type for the number of opps in the opp list
and uses the 'unsigned long' type for each frequency. So, this patch
modifies the type of some variable as following:
- the type of freq_table : unsigned int -> unsigned long
- the type of max_state : unsigned int -> int
- Corrected types, format strings, mutex usages by MyungJoo
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
This patch adds the 'show_one' macro to simplify the duplicate code
of both max_freq_show() and min_freq_show().
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
This patch just fixes following error and warning by using
scripts/checkpatch.pl.
- Follwoing issue from checkpatch.pl:
ERROR: space prohibited before that close parenthesis ')'
+ if (count < 0 ) {
WARNING: line over 80 characters
+ ptr = devres_alloc(devm_devfreq_event_release, sizeof(*ptr), GFP_KERNEL);
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
This patch just removes the error log when
devfreq_event_get_edev_by_phandle() fail to get the instance of
devfreq-event device. It is related to sequence of the probe() of each
driver. So, this error log might show the always during kernel booting.
Each driver using this function can show the appropriate error log.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
When device_register() fails, kfree(devfreq) is called already in
devfreq_dev_release(), hence there is no need to call kfree(devfreq)
in err_dev again.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
Writing the currently set governor into sysfs currently
seems to fail.
Fix this by setting the return code to zero before
leaving governor_store().
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
time_in_state in struct devfreq is defined as unsigned long, so
devm_kzalloc should use sizeof(unsigned long) as argument instead
of sizeof(unsigned int), otherwise it will cause unexpected result
in 64bit system.
Signed-off-by: Xiaolong Ye <yexl@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
Direct invocation of get_dev_status() is no more recommended.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
The thermal infrastructure should use the devfreq cooling device, which
uses the OPP library to disable OPPs as necessary.
Fix a couple of typos in the same comment while we are at it.
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
The return value of get_dev_status() can be reused. Cache it so that
other parts of the kernel can reuse it instead of having to call the
same function again.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
IS_ERR(_OR_NULL) already contain an 'unlikely' compiler flag and there
is no need to do that again from its callers. Drop it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
