| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes a Kconfig dependency for hisilicon as well as a double free
in marvell/octeontx"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: marvell/octeontx - fix double free of ptr
crypto: hisilicon - Fix build error
|
|
Pull networking fixes from David Miller:
1) Slave bond and team devices should not be assigned ipv6 link local
addresses, from Jarod Wilson.
2) Fix clock sink config on some at803x PHY devices, from Oleksij
Rempel.
3) Uninitialized stack space transmitted in slcan frames, fix from
Richard Palethorpe.
4) Guard HW VLAN ops properly in stmmac driver, from Jose Abreu.
5) "=" --> "|=" fix in aquantia driver, from Colin Ian King.
6) Fix TCP fallback in mptcp, from Florian Westphal. (accessing a plain
tcp_sk as if it were an mptcp socket).
7) Fix cavium driver in some configurations wrt. PTP, from Yue Haibing.
8) Make ipv6 and ipv4 consistent in the lower bound allowed for
neighbour entry retrans_time, from Hangbin Liu.
9) Don't use private workqueue in pegasus usb driver, from Petko
Manolov.
10) Fix integer overflow in mlxsw, from Colin Ian King.
11) Missing refcnt init in cls_tcindex, from Cong Wang.
12) One too many loop iterations when processing cmpri entries in ipv6
rpl code, from Alexander Aring.
13) Disable SG and TSO by default in r8169, from Heiner Kallweit.
14) NULL deref in macsec, from Davide Caratti.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (42 commits)
macsec: fix NULL dereference in macsec_upd_offload()
skbuff.h: Improve the checksum related comments
net: dsa: bcm_sf2: Ensure correct sub-node is parsed
qed: remove redundant assignment to variable 'rc'
wimax: remove some redundant assignments to variable result
mlxsw: spectrum_flower: Do not stop at FLOW_ACTION_VLAN_MANGLE
mlxsw: spectrum_flower: Do not stop at FLOW_ACTION_PRIORITY
r8169: change back SG and TSO to be disabled by default
net: dsa: bcm_sf2: Do not register slave MDIO bus with OF
ipv6: rpl: fix loop iteration
tun: Don't put_page() for all negative return values from XDP program
net: dsa: mt7530: fix null pointer dereferencing in port5 setup
mptcp: add some missing pr_fmt defines
net: phy: micrel: kszphy_resume(): add delay after genphy_resume() before accessing PHY registers
net_sched: fix a missing refcnt in tcindex_init()
net: stmmac: dwmac1000: fix out-of-bounds mac address reg setting
mlxsw: spectrum_trap: fix unintention integer overflow on left shift
pegasus: Remove pegasus' own workqueue
neigh: support smaller retrans_time settting
net: openvswitch: use hlist_for_each_entry_rcu instead of hlist_for_each_entry
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here are three SPDX patches for 5.7-rc1.
One fixes up the SPDX tag for a single driver, while the other two go
through the tree and add SPDX tags for all of the .gitignore files as
needed.
Nothing too complex, but you will get a merge conflict with your
current tree, that should be trivial to handle (one file modified by
two things, one file deleted.)
All three of these have been in linux-next for a while, with no
reported issues other than the merge conflict"
* tag 'spdx-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx:
ASoC: MT6660: make spdxcheck.py happy
.gitignore: add SPDX License Identifier
.gitignore: remove too obvious comments
|
|
Currently in the case where eq->src != req->ds, the allocation of
ptr is kfree'd at the end of the code block. However later on in
the case where enc is not null any of the error return paths that
return via the error handling return path end up performing an
erroneous second kfree of ptr.
Fix this by adding an error exit label error_free and only jump to
this when ptr needs kfree'ing thus avoiding the double free issue.
Addresses-Coverity: ("Double free")
Fixes: 10b4f09491bf ("crypto: marvell - add the Virtual Function driver for CPT")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When UACCE is m, CRYPTO_DEV_HISI_QM cannot be built-in.
But CRYPTO_DEV_HISI_QM is selected by CRYPTO_DEV_HISI_SEC2
and CRYPTO_DEV_HISI_HPRE unconditionally, which may leads this:
drivers/crypto/hisilicon/qm.o: In function 'qm_alloc_uacce':
drivers/crypto/hisilicon/qm.c:1579: undefined reference to 'uacce_alloc'
Add Kconfig dependency to enforce usable configurations.
Fixes: 47c16b449921 ("crypto: hisilicon - qm depends on UACCE")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
drivers/crypto/chelsio/chcr_ktls.c: In function ‘chcr_short_record_handler’:
drivers/crypto/chelsio/chcr_ktls.c:1770:12: error: implicit declaration of function ‘kmap_atomic’;
did you mean ‘in_atomic’? [-Werror=implicit-function-declaration]
vaddr = kmap_atomic(skb_frag_page(f));
^~~~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: dc05f3df8fac ("chcr: Handle first or middle part of record")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"API:
- Fix out-of-sync IVs in self-test for IPsec AEAD algorithms
Algorithms:
- Use formally verified implementation of x86/curve25519
Drivers:
- Enhance hwrng support in caam
- Use crypto_engine for skcipher/aead/rsa/hash in caam
- Add Xilinx AES driver
- Add uacce driver
- Register zip engine to uacce in hisilicon
- Add support for OCTEON TX CPT engine in marvell"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (162 commits)
crypto: af_alg - bool type cosmetics
crypto: arm[64]/poly1305 - add artifact to .gitignore files
crypto: caam - limit single JD RNG output to maximum of 16 bytes
crypto: caam - enable prediction resistance in HRWNG
bus: fsl-mc: add api to retrieve mc version
crypto: caam - invalidate entropy register during RNG initialization
crypto: caam - check if RNG job failed
crypto: caam - simplify RNG implementation
crypto: caam - drop global context pointer and init_done
crypto: caam - use struct hwrng's .init for initialization
crypto: caam - allocate RNG instantiation descriptor with GFP_DMA
crypto: ccree - remove duplicated include from cc_aead.c
crypto: chelsio - remove set but not used variable 'adap'
crypto: marvell - enable OcteonTX cpt options for build
crypto: marvell - add the Virtual Function driver for CPT
crypto: marvell - add support for OCTEON TX CPT engine
crypto: marvell - create common Kconfig and Makefile for Marvell
crypto: arm/neon - memzero_explicit aes-cbc key
crypto: bcm - Use scnprintf() for avoiding potential buffer overflow
crypto: atmel-i2c - Fix wakeup fail
...
|
|
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
|
|
There is a possibility that cdev is removed before CPL_ABORT_REQ_RSS
is fully processed, so it's better to save it in skb.
Added checks in handling the flow correctly, which suggests connection reset
request is sent to HW, wait for HW to respond.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 header's payload length field shouldn't include IPv6 header length.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The locks are taken in this order during driver registration
(uld_mutex), at: cxgb4_register_uld.part.14+0x49/0xd60 [cxgb4]
(rtnl_mutex), at: rtnetlink_rcv_msg+0x2db/0x400
(uld_mutex), at: cxgb_up+0x3a/0x7b0 [cxgb4]
(rtnl_mutex), at: chcr_add_xfrmops+0x83/0xa0 [chcr](stucked here)
To avoid this now the netdev features are updated after the
cxgb4_register_uld function is completed.
Fixes: 6dad4e8ab3ec6 ("chcr: Add support for Inline IPSec").
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This issue occurs only when multiadapters are present. Hang
happens because assign_chcr_device returns u_ctx pointer of
adapter which is not yet initialized as for this adapter cxgb_up
is not been called yet.
The last_dev pointer is used to determine u_ctx pointer and it
is initialized two times in chcr_uld_add in chcr_dev_add respectively.
The fix here is don't initialize the last_dev pointer during
chcr_uld_add. Only assign to value to it when the adapter's
initialization is completed i.e in chcr_dev_add.
Fixes: fef4912b66d62 ("crypto: chelsio - Handle PCI shutdown event").
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to follow recommendation in SP800-90C (section "9.4 The
Oversampling-NRBG Construction") limit the output of "generate" JD
submitted to CAAM. See
https://lore.kernel.org/linux-crypto/VI1PR0402MB3485EF10976A4A69F90E5B0F98580@VI1PR0402MB3485.eurprd04.prod.outlook.com/
for more details.
This change should make CAAM's hwrng driver good enough to have 1024
quality rating.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Horia Geantă <horia.geanta@nxp.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Iuliana Prodan <iuliana.prodan@nxp.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Instantiate CAAM RNG with prediction resistance enabled to improve its
quality (with PR on DRNG is forced to reseed from TRNG every time
random data is generated).
Management Complex firmware with version lower than 10.20.0
doesn't provide prediction resistance support. Consider this
and only instantiate rng when mc f/w version is lower.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Andrei Botila <andrei.botila@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Horia Geantă <horia.geanta@nxp.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Iuliana Prodan <iuliana.prodan@nxp.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
In order to make sure that we always use non-stale entropy data, change
the code to invalidate entropy register during RNG initialization.
Signed-off-by: Aymen Sghaier <aymen.sghaier@nxp.com>
Signed-off-by: Vipul Kumar <vipul_kumar@mentor.com>
[andrew.smirnov@gmail.com ported to upstream kernel, rewrote commit msg]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Horia Geantă <horia.geanta@nxp.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Iuliana Prodan <iuliana.prodan@nxp.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
We shouldn't stay silent if RNG job fails. Add appropriate code to
check for that case and propagate error code up appropriately.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Horia Geantă <horia.geanta@nxp.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Iuliana Prodan <iuliana.prodan@nxp.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Rework CAAM RNG implementation as follows:
- Make use of the fact that HWRNG supports partial reads and will
handle such cases gracefully by removing recursion in caam_read()
- Convert blocking caam_read() codepath to do a single blocking job
read directly into requested buffer, bypassing any intermediary
buffers
- Convert async caam_read() codepath into a simple single
reader/single writer FIFO use-case, thus simplifying concurrency
handling and delegating buffer read/write position management to KFIFO
subsystem.
- Leverage the same low level RNG data extraction code for both async
and blocking caam_read() scenarios, get rid of the shared job
descriptor and make non-shared one as a simple as possible (just
HEADER + ALGORITHM OPERATION + FIFO STORE)
- Split private context from DMA related memory, so that the former
could be allocated without GFP_DMA.
NOTE: On its face value this commit decreased throughput numbers
reported by
dd if=/dev/hwrng of=/dev/null bs=1 count=100K [iflag=nonblock]
by about 15%, however commits that enable prediction resistance and
limit JR total size impact the performance so much and move the
bottleneck such as to make this regression irrelevant.
NOTE: On the bright side, this commit reduces RNG in kernel DMA buffer
memory usage from 2 x RN_BUF_SIZE (~256K) to 32K.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Horia Geantă <horia.geanta@nxp.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Iuliana Prodan <iuliana.prodan@nxp.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Leverage devres to get rid of code storing global context as well as
init_done flag.
Original code also has a circular deallocation dependency where
unregister_algs() -> caam_rng_exit() -> caam_jr_free() chain would
only happen if all of JRs were freed. Fix this by moving
caam_rng_exit() outside of unregister_algs() and doing it specifically
for JR that instantiated HWRNG.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Horia Geantă <horia.geanta@nxp.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Iuliana Prodan <iuliana.prodan@nxp.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Make caamrng code a bit more symmetric by moving initialization code
to .init hook of struct hwrng.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Horia Geantă <horia.geanta@nxp.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Iuliana Prodan <iuliana.prodan@nxp.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Be consistent with the rest of the codebase and use GFP_DMA when
allocating memory for a CAAM JR descriptor.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Horia Geantă <horia.geanta@nxp.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Iuliana Prodan <iuliana.prodan@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add SPDX License Identifier to all .gitignore files.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The new macro set has a consistent namespace and uses C99 initializers
instead of the grufty C89 ones.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lkml.kernel.org/r/20200320131510.700250889@linutronix.de
|
|
Kernel TLS forms TLS header in kernel during encryption and removes
while decryption before giving packet back to user application. The
similar logic is introduced in chtls code as well.
v1->v2:
- tls_proccess_cmsg() uses tls_handle_open_record() which is not required
in TOE-TLS. Don't mix TOE with other TLS types.
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/crypto/chelsio/chcr_algo.c: In function 'chcr_device_init':
drivers/crypto/chelsio/chcr_algo.c:1440:18: warning:
variable 'adap' set but not used [-Wunused-but-set-variable]
commit 567be3a5d227 ("crypto: chelsio - Use multiple txq/rxq per tfm
to process the requests") involved this unused variable.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add the OcteonTX cpt options in crypto Kconfig and Makefile
Signed-off-by: SrujanaChalla <schalla@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add support for the cryptographic accelerator unit virtual functions on
OcteonTX 83XX SoC.
Co-developed-by: Lukasz Bartosik <lbartosik@marvell.com>
Signed-off-by: Lukasz Bartosik <lbartosik@marvell.com>
Signed-off-by: SrujanaChalla <schalla@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add support for the cryptographic acceleration unit (CPT) on
OcteonTX CN83XX SoC.
Co-developed-by: Lukasz Bartosik <lbartosik@marvell.com>
Signed-off-by: Lukasz Bartosik <lbartosik@marvell.com>
Signed-off-by: SrujanaChalla <schalla@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Creats common Kconfig and Makefile for Marvell crypto drivers.
Signed-off-by: SrujanaChalla <schalla@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The wake token cannot be sent without ignoring the nack for the
device address
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Combine found device and created qp into one operation instead of found
device and create qp both are independent operations. when execute
multiple tasks, the different threads may find same device at the same
time, but the number of queues is insufficient on the device. causing
one of threads fail to create a qp. Now fix this, First find device then
create qp, if result failure. the current thread will find next device.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Shukun Tan <tanshukun1@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Reviewed-by: Zaibo Xu <xuzaibo@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Optimize finding hpre device process according to priority of numa
distance.
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: Shukun Tan <tanshukun1@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Reviewed-by: Zaibo Xu <xuzaibo@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Encapsulate hisi_qm_alloc_qps_node() to new interface to replace
find_zip_device(), which will fix the bug of creating QP failure
especially in multi-thread scenario.
Signed-off-by: Shukun Tan <tanshukun1@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Reviewed-by: Zaibo Xu <xuzaibo@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Use struct hisi_qm to maintain device list. Meanwhile, add two external
interface into qm, merge find proper device and create qp into QP alloc
logic, merge release qps into QP free logic.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Shukun Tan <tanshukun1@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Reviewed-by: Zaibo Xu <xuzaibo@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
drivers/crypto/chelsio/chcr_ktls.c: In function chcr_ktls_cpl_set_tcb_rpl:
drivers/crypto/chelsio/chcr_ktls.c:662:11: warning:
variable status set but not used [-Wunused-but-set-variable]
commit 8a30923e1598 ("cxgb4/chcr: Save tx keys and handle HW response")
involved this unused variable, remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Our handling of ciphers with IV trailing the AAD was correct
but overly complicated. Refactor to simplify and possibly
save one DMA burst.
This has the added bonus of behaving the same as the generic
rfc4543 implementation for none compliants inputs where the
IV in the iv field was not the same as the IV in the AAD.
There should be no change in behaviour with correct inputs.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Use crypto_ipsec_check_assoclen() instead of home grown functions.
Clean up some unneeded code as a result. Delete stale comments
while we're at it.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Move testing of condition to after the point we decide if
we need it or not.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Remove left over ancient and now misleading TODO remarks.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
removed pointless comment
Signed-off-by: Hadar Gat <hadar.gat@arm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Changed CC_GENMASK macro so it can be used for all HW registers.
Signed-off-by: Hadar Gat <hadar.gat@arm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Instead of using CAP_SYS_ADMIN which is restricted to the root user,
check the file mode for write permissions before executing commands that
can affect the platform. This allows for more fine-grained access
control to the SEV ioctl interface. This would allow a SEV-only user
or group the ability to administer the platform without requiring them
to be root or granting them overly powerful permissions.
For example:
chown root:root /dev/sev
chmod 600 /dev/sev
setfacl -m g:sev:r /dev/sev
setfacl -m g:sev-admin:rw /dev/sev
In this instance, members of the "sev-admin" group have the ability to
perform all ioctl calls (including the ones that modify platform state).
Members of the "sev" group only have access to the ioctls that do not
modify the platform state.
This also makes opening "/dev/sev" more consistent with how file
descriptors are usually handled. By only checking for CAP_SYS_ADMIN,
the file descriptor could be opened read-only but could still execute
ioctls that modify the platform state. This patch enforces that the file
descriptor is opened with write privileges if it is going to be used to
modify the platform state.
This flexibility is completely opt-in, and if it is not desirable by
the administrator then they do not need to give anyone else access to
/dev/sev.
Signed-off-by: Connor Kuehl <ckuehl@redhat.com>
Reviewed-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Bandan Das <bsd@redhat.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
In the scenario of SMMU translation, the SEC performance of short messages
(<512Bytes) cannot meet our expectations. To avoid this, we reserve the
plat buffer (PBUF) memory for small packets when creating TFM.
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Zaibo Xu <xuzaibo@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
We have updated the operation method of IV and MAC address
to prepare for pbuf patch and fixed coding style.
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Zaibo Xu <xuzaibo@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
In order to improve performance of small packets (<512Bytes)
in SMMU translation scenario, we need to identify the type of IOMMU
in the SEC probe to process small packets by a different method.
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Zaibo Xu <xuzaibo@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Allocate one workqueue for each QM instead of one for all QMs,
we found the throughput of SEC engine can be increased to
the hardware limit throughput during testing sec2 performance.
so we added this scheme.
Signed-off-by: Ye Kai <yekai13@huawei.com>
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Zaibo Xu <xuzaibo@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Since SEC need not so many workqueues as our test, we just use
one workqueue created by the device driver of QM if necessary,
which will also reduce CPU waste without any throughput decreasing.
Signed-off-by: Shukun Tan <tanshukun1@huawei.com>
Signed-off-by: Zaibo Xu <xuzaibo@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The CONFIG_CRYPTO_DEV_QCE_SOFT_THRESHOLD symbol was renamed during
development, but the stringify reference in the parameter description
sneaked by unnoticed.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
simplify code to remove unnecessary constant string copies.
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
