| Age | Commit message (Collapse) | Author |
|---|
|
* pm-cpufreq-fixes:
cpufreq: intel_pstate: Always set max P-state in performance mode
cpufreq: intel_pstate: Set P-state upfront in performance mode
* pm-sleep-fixes:
PM / suspend: Fix missing KERN_CONT for suspend message
|
|
The only times at which intel_pstate checks the policy set for
a given CPU is the initialization of that CPU and updates of its
policy settings from cpufreq when intel_pstate_set_policy() is
invoked.
That is insufficient, however, because intel_pstate uses the same
P-state selection function for all CPUs regardless of the policy
setting for each of them and the P-state limits are shared between
them. Thus if the policy is set to "performance" for a particular
CPU, it may not behave as expected if the cpufreq settings are
changed subsequently for another CPU.
That can be easily demonstrated by writing "performance" to
scaling_governor for all CPUs and then switching it to "powersave"
for one of them in which case all of the CPUs will behave as though
their scaling_governor were all "powersave" (even though the policy
still appears to be "performance" for the remaining CPUs).
Fix this problem by modifying intel_pstate_adjust_busy_pstate() to
always set the P-state to the maximum allowed by the current limits
for all CPUs whose policy is set to "performance".
Note that it still is recommended to always change the policy setting
in the same way for all CPUs even with this fix applied to avoid
confusion.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
After commit a4675fbc4a7a (cpufreq: intel_pstate: Replace timers with
utilization update callbacks) the cpufreq governor callbacks may not
be invoked on NOHZ_FULL CPUs and, in particular, switching to the
"performance" policy via sysfs may not have any effect on them. That
is a problem, because it usually is desirable to squeeze the last
bit of performance out of those CPUs, so work around it by setting
the maximum P-state (within the limits) in intel_pstate_set_policy()
upfront when the policy is CPUFREQ_POLICY_PERFORMANCE.
Fixes: a4675fbc4a7a (cpufreq: intel_pstate: Replace timers with utilization update callbacks)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"This includes a couple of fixes for cpufreq regressions introduced in
4.8, a rework of the intel_pstate algorithm used on Atom processors
(that took some time to test) plus a fix and a couple of cleanups in
that driver, a CPPC cpufreq driver fix, and a some devfreq fixes and
cleanups (core and exynos-nocp).
Specifics:
- Fix two cpufreq regressions causing undesirable changes in behavior
to appear (one in the core and one in the conservative governor)
introduced during the 4.8 cycle (Aaro Koskinen, Rafael Wysocki).
- Fix the way the intel_pstate driver accesses MSRs related to the
hardware-managed P-states (HWP) feature during the initialization
which currently is unsafe and may cause the processor to generate a
general protection fault (Srinivas Pandruvada).
- Rework the intel_pstate's P-state selection algorithm used on Atom
processors to avoid known problems with the current one and to make
the computation more straightforward, which also happens to improve
performance in multiple benchmarks a bit (Rafael Wysocki).
- Improve two comments in the intel_pstate driver (Rafael Wysocki).
- Fix the desired performance computation in the CPPC cpufreq driver
(Hoan Tran).
- Fix the devfreq core to avoid printing misleading error messages in
some cases (Tobias Jakobi).
- Fix the error code path in devfreq_add_device() to use proper
locking around list modifications (Axel Lin).
- Fix a build failure and remove a couple of redundant updates of
variables in the exynos-nocp devfreq driver (Axel Lin)"
* tag 'pm-extra-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: CPPC: Correct desired_perf calculation
cpufreq: conservative: Fix next frequency selection
cpufreq: skip invalid entries when searching the frequency
cpufreq: intel_pstate: Fix struct pstate_adjust_policy kerneldoc
cpufreq: intel_pstate: Proportional algorithm for Atom
PM / devfreq: Skip status update on uninitialized previous_freq
PM / devfreq: Add proper locking around list_del()
PM / devfreq: exynos-nocp: Remove redundant code
PM / devfreq: exynos-nocp: Select REGMAP_MMIO
cpufreq: intel_pstate: Clarify comment in get_target_pstate_use_performance()
cpufreq: intel_pstate: Fix unsafe HWP MSR access
|
|
The desired_perf is an abstract performance number. Its value should
be in the range of [lowest perf, highest perf] of CPPC.
The correct calculation is
desired_perf = freq * cppc_highest_perf / cppc_dmi_max_khz
And cppc_cpufreq_set_target() returns if desired_perf is exactly
the same with the old perf.
Signed-off-by: Hoan Tran <hotran@apm.com>
Reviewed-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit d352cf47d93e (cpufreq: conservative: Do not use transition
notifications) overlooked the case when the "frequency step" used
by the conservative governor is small relative to the distances
between the available frequencies and broke the algorithm by
using policy->cur instead of the previously requested frequency
when computing the next one.
As a result, the governor may not be able to go outside of a narrow
range between two consecutive available frequencies.
Fix the problem by making the governor save the previously requested
frequency and select the next one relative that value (unless it is
out of range, in which case policy->cur will be used instead).
Fixes: d352cf47d93e (cpufreq: conservative: Do not use transition notifications)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=177171
Reported-and-tested-by: Aleksey Rybalkin <aleksey@rybalkin.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.8+ <stable@vger.kernel.org> # 4.8+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
It looks like the name of struct pstate_adjust_policy was updated
without updating its kerneldoc comment accordingly, so fix that
mistake.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The PID algorithm used by the intel_pstate driver tends to drive
performance to the minimum for workloads with utilization below the
setpoint, which is undesirable, so replace it with a modified
"proportional" algorithm on Atom.
The new algorithm will set the new P-state to be 1.25 times the
available maximum times the (frequency-invariant) utilization during
the previous sampling period except when the target P-state computed
this way is lower than the average P-state during the previous
sampling period. In the latter case, it will increase the target by
50% of the difference between it and the average P-state to prevent
performance from dropping down too fast in some cases.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
Make the comment explaining the meaning of the perf_scaled variable
in get_target_pstate_use_performance() more straightforward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This is a requirement that MSR MSR_PM_ENABLE must be set to 0x01 before
reading MSR_HWP_CAPABILITIES on a given CPU. If cpufreq init() is
scheduled on a CPU which is not same as policy->cpu or migrates to a
different CPU before calling msr read for MSR_HWP_CAPABILITIES, it
is possible that MSR_PM_ENABLE was not to set to 0x01 on that CPU.
This will cause GP fault. So like other places in this path
rdmsrl_on_cpu should be used instead of rdmsrl.
Moreover the scope of MSR_HWP_CAPABILITIES is on per thread basis, so it
should be read from the same CPU, for which MSR MSR_HWP_REQUEST is
getting set.
dmesg dump or warning:
[ 22.014488] WARNING: CPU: 139 PID: 1 at arch/x86/mm/extable.c:50 ex_handler_rdmsr_unsafe+0x68/0x70
[ 22.014492] unchecked MSR access error: RDMSR from 0x771
[ 22.014493] Modules linked in:
[ 22.014507] CPU: 139 PID: 1 Comm: swapper/0 Not tainted 4.7.5+ #1
...
...
[ 22.014516] Call Trace:
[ 22.014542] [<ffffffff813d7dd1>] dump_stack+0x63/0x82
[ 22.014558] [<ffffffff8107bc8b>] __warn+0xcb/0xf0
[ 22.014561] [<ffffffff8107bcff>] warn_slowpath_fmt+0x4f/0x60
[ 22.014563] [<ffffffff810676f8>] ex_handler_rdmsr_unsafe+0x68/0x70
[ 22.014564] [<ffffffff810677d9>] fixup_exception+0x39/0x50
[ 22.014604] [<ffffffff8102e400>] do_general_protection+0x80/0x150
[ 22.014610] [<ffffffff817f9ec8>] general_protection+0x28/0x30
[ 22.014635] [<ffffffff81687940>] ? get_target_pstate_use_performance+0xb0/0xb0
[ 22.014642] [<ffffffff810600c7>] ? native_read_msr+0x7/0x40
[ 22.014657] [<ffffffff81688123>] intel_pstate_hwp_set+0x23/0x130
[ 22.014660] [<ffffffff81688406>] intel_pstate_set_policy+0x1b6/0x340
[ 22.014662] [<ffffffff816829bb>] cpufreq_set_policy+0xeb/0x2c0
[ 22.014664] [<ffffffff81682f39>] cpufreq_init_policy+0x79/0xe0
[ 22.014666] [<ffffffff81682cb0>] ? cpufreq_update_policy+0x120/0x120
[ 22.014669] [<ffffffff816833a6>] cpufreq_online+0x406/0x820
[ 22.014671] [<ffffffff8168381f>] cpufreq_add_dev+0x5f/0x90
[ 22.014717] [<ffffffff81530ac8>] subsys_interface_register+0xb8/0x100
[ 22.014719] [<ffffffff816821bc>] cpufreq_register_driver+0x14c/0x210
[ 22.014749] [<ffffffff81fe1d90>] intel_pstate_init+0x39d/0x4d5
[ 22.014751] [<ffffffff81fe13f2>] ? cpufreq_gov_dbs_init+0x12/0x12
Cc: 4.3+ <stable@vger.kernel.org> # 4.3+
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull ARM updates from Russell King:
- Correct ARMs dma-mapping to use the correct printk format strings.
- Avoid defining OBJCOPYFLAGS globally which upsets lkdtm rodata
testing.
- Cleanups to ARMs asm/memory.h include.
- L2 cache cleanups.
- Allow flat nommu binaries to be executed on ARM MMU systems.
- Kernel hardening - add more read-only after init annotations,
including making some kernel vdso variables const.
- Ensure AMBA primecell clocks are appropriately defaulted.
- ARM breakpoint cleanup.
- Various StrongARM 11x0 and companion chip (SA1111) updates to bring
this legacy platform to use more modern APIs for (eg) GPIOs and
interrupts, which will allow us in the future to reduce some of the
board-level driver clutter and elimate function callbacks into board
code via platform data. There still appears to be interest in these
platforms!
- Remove the now redundant secure_flush_area() API.
- Module PLT relocation optimisations. Ard says: This series of 4
patches optimizes the ARM PLT generation code that is invoked at
module load time, to get rid of the O(n^2) algorithm that results in
pathological load times of 10 seconds or more for large modules on
certain STB platforms.
- ARMv7M cache maintanence support.
- L2 cache PMU support
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (35 commits)
ARM: sa1111: provide to_sa1111_device() macro
ARM: sa1111: add sa1111_get_irq()
ARM: sa1111: clean up duplication in IRQ chip implementation
ARM: sa1111: implement a gpio_chip for SA1111 GPIOs
ARM: sa1111: move irq cleanup to separate function
ARM: sa1111: use devm_clk_get()
ARM: sa1111: use devm_kzalloc()
ARM: sa1111: ensure we only touch RAB bus type devices when removing
ARM: 8611/1: l2x0: add PMU support
ARM: 8610/1: V7M: Add dsb before jumping in handler mode
ARM: 8609/1: V7M: Add support for the Cortex-M7 processor
ARM: 8608/1: V7M: Indirect proc_info construction for V7M CPUs
ARM: 8607/1: V7M: Wire up caches for V7M processors with cache support.
ARM: 8606/1: V7M: introduce cache operations
ARM: 8605/1: V7M: fix notrace variant of save_and_disable_irqs
ARM: 8604/1: V7M: Add support for reading the CTR with read_cpuid_cachetype()
ARM: 8603/1: V7M: Add addresses for mem-mapped V7M cache operations
ARM: 8602/1: factor out CSSELR/CCSIDR operations that use cp15 directly
ARM: kernel: avoid brute force search on PLT generation
ARM: kernel: sort relocation sections before allocating PLTs
...
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull CPU hotplug updates from Thomas Gleixner:
"Yet another batch of cpu hotplug core updates and conversions:
- Provide core infrastructure for multi instance drivers so the
drivers do not have to keep custom lists.
- Convert custom lists to the new infrastructure. The block-mq custom
list conversion comes through the block tree and makes the diffstat
tip over to more lines removed than added.
- Handle unbalanced hotplug enable/disable calls more gracefully.
- Remove the obsolete CPU_STARTING/DYING notifier support.
- Convert another batch of notifier users.
The relayfs changes which conflicted with the conversion have been
shipped to me by Andrew.
The remaining lot is targeted for 4.10 so that we finally can remove
the rest of the notifiers"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
cpufreq: Fix up conversion to hotplug state machine
blk/mq: Reserve hotplug states for block multiqueue
x86/apic/uv: Convert to hotplug state machine
s390/mm/pfault: Convert to hotplug state machine
mips/loongson/smp: Convert to hotplug state machine
mips/octeon/smp: Convert to hotplug state machine
fault-injection/cpu: Convert to hotplug state machine
padata: Convert to hotplug state machine
cpufreq: Convert to hotplug state machine
ACPI/processor: Convert to hotplug state machine
virtio scsi: Convert to hotplug state machine
oprofile/timer: Convert to hotplug state machine
block/softirq: Convert to hotplug state machine
lib/irq_poll: Convert to hotplug state machine
x86/microcode: Convert to hotplug state machine
sh/SH-X3 SMP: Convert to hotplug state machine
ia64/mca: Convert to hotplug state machine
ARM/OMAP/wakeupgen: Convert to hotplug state machine
ARM/shmobile: Convert to hotplug state machine
arm64/FP/SIMD: Convert to hotplug state machine
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"First off, the ACPICA code in the kernel is updated to upstream
revision 20160831 that brings in a few bug fixes and cleanups. In
particular, it is possible to mask GPEs now (and the sysfs interface
for GPE control is fixed on top of that), problems related to the
table loading mechanism are fixed and all code related to FADT version
2 (which has never been part of the ACPI specification) is dropped.
On the new features front, there is a new watchdog driver based on the
ACPI WDAT (ACPI Watchdog Action Table), needed on some platforms to
replace the iTCO watchdog that doesn't work there, and some UART
devices get new definitions of built-in properties (to be accessed via
the generic device properties API).
Also, included is a fix for an ACPI-related PCI resorces allocation
issue and a few problems in the EC driver and in the button and
battery drivers are fixed.
In addition to that, the ACPI CPPC library is updated to make batching
of requests sent over the PCC channel possible (which reduces the PCC
usage overhead substantially in some cases) and to support functional
fixed hardware (FFH) type of CPPC registers access (which will allow
CPPC to be used on x86 too in the future).
As usual, there are some assorted fixes and cleanups too.
Specifics:
- Update of the ACPICA code in the kernel to upstream revision
20160831 with the following major changes:
* New mechanism for GPE masking.
* Fixes for issues related to the LoadTable operator and table
loading.
* Fixes for issues related to so-called module-level code (MLC),
that is AML that doesn't belong to any methods.
* Change of the return value of the _OSI method to reflect the
Windows behavior.
* GAS (Generic Address Structure) support fix related to 32-bit
FADT addresses.
* Elimination of unnecessary FADT version 2 support.
* ACPI tools fixes and cleanups.
From Bob Moore, Lv Zheng, and Jung-uk Kim.
- ACPI sysfs interface updates to fix GPE handling (on top of the new
GPE masking mechanism in ACPICA) and issues related to table
loading (Lv Zheng).
- New watchdog driver based on the ACPI WDAT (ACPI Watchdog Action
Table), needed on some platforms to replace the iTCO watchdog that
doesn't work there and related updates of the intel_pmc_ipc,
i2c/i801 and MFD/lcp_ich drivers (Mika Westerberg).
- Driver core fix to prevent it from leaking secondary fwnode objects
during device removal (Lukas Wunner).
- New definitions of built-in properties for UART in ACPI-based x86
SoC drivers and a 8250_dw driver quirk for the APM X-Gene SoC
(Heikki Krogerus).
- New device ID for the Vulcan SPI controller and constification of
local strucures in the AMD SoC (APD) ACPI driver (Kamlakant Patel,
Julia Lawall).
- Fix for a bug causing the allocation of PCI resorces to fail if
ACPI-enumerated child platform devices are registered below the PCI
devices in question (Mika Westerberg).
- Change of the default polarity for PCI legacy IRQs to high on
systems booting wth ACPI on platforms with a GIC interrupt
controller model fixing the discrepancy between the specification
and HW behavior (Lorenzo Pieralisi).
- Fixes for the handling of system suspend/resume in the ACPI EC
driver and update of that driver to make it cope with the cases
when the EC device defined in the ECDT has to be used throughout
the entire system life cycle (Lv Zheng).
- Update of the ACPI CPPC library to allow it to batch requests sent
over the PCC channel (to reduce overhead), to support the fixed
functional hardware (FFH) CPPC registers access type, to notify the
mailbox framework about TX completions when the interrupt flag is
set for the PCC mailbox, and to support HW-Reduced Communication
Subspace type 2 (Ashwin Chaugule, Prashanth Prakash, Srinivas
Pandruvada, Hoan Tran).
- ACPI button driver fix and documentation update related to the
handling of laptop lids (Lv Zheng).
- ACPI battery driver initialization fix (Carlos Garnacho).
- ACPI GPIO enumeration documentation update (Mika Westerberg).
- Assorted updates of the core ACPI bus type code (Lukas Wunner, Lv
Zheng).
- Assorted cleanups of the ACPI table parsing code and the
x86-specific ACPI code (Al Stone).
- Fixes for assorted ACPI-related issues found in linux-next (Wei
Yongjun)"
* tag 'acpi-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (98 commits)
ACPI / documentation: Use recommended name in GPIO property names
watchdog: wdat_wdt: Fix warning for using 0 as NULL
watchdog: wdat_wdt: fix return value check in wdat_wdt_probe()
platform/x86: intel_pmc_ipc: Do not create iTCO watchdog when WDAT table exists
i2c: i801: Do not create iTCO watchdog when WDAT table exists
mfd: lpc_ich: Do not create iTCO watchdog when WDAT table exists
ACPI / bus: Adjust ACPI subsystem initialization for new table loading mode
ACPICA: Parser: Fix a regression in LoadTable support
ACPICA: Tables: Fix "UNLOAD" code path lock issues
ACPI / watchdog: Add support for WDAT hardware watchdog
ACPI / platform: Pay attention to parent device's resources
PCI: Add pci_find_resource()
ACPI / CPPC: Support PCC with interrupt flag
ACPI / sysfs: Update sysfs signature handling code
ACPI / sysfs: Fix an issue for LoadTable opcode
ACPICA: Tables: Fix a regression in acpi_tb_find_table()
ACPI / tables: Remove duplicated include from tables.c
ACPI / APD: constify local structures
x86: ACPI: make variable names clearer in acpi_parse_madt_lapic_entries()
x86: ACPI: remove extraneous white space after semicolon
...
|
|
|
|
* acpi-x86:
x86: ACPI: make variable names clearer in acpi_parse_madt_lapic_entries()
x86: ACPI: remove extraneous white space after semicolon
* acpi-cppc:
ACPI / CPPC: Support PCC with interrupt flag
ACPI / CPPC: Add prefix cppc to cpudata structure name
ACPI / CPPC: Add support for functional fixed hardware address
ACPI / CPPC: Don't return on CPPC probe failure
ACPI / CPPC: Allow build with ACPI_CPU_FREQ_PSS config
ACPI / CPPC: check for error bit in PCC status field
ACPI / CPPC: move all PCC related information into pcc_data
ACPI / CPPC: add sysfs support to compute delivered performance
ACPI / CPPC: set a non-zero value for transition_latency
ACPI / CPPC: support for batching CPPC requests
ACPI / CPPC: acquire pcc_lock only while accessing PCC subspace
ACPI / CPPC: restructure read/writes for efficient sys mapped reg ops
mailbox: pcc: Support HW-Reduced Communication Subspace type 2
* acpi-soc:
ACPI / APD: constify local structures
ACPI / APD: Add device HID for Vulcan SPI controller
|
|
Trival fix, dev_err message is missing a \n, so add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Trival fix, dev_err messages are missing a \n, so add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The function cpufreq_register_driver() returns zero on success and since
commit 27622b061eb4 ("cpufreq: Convert to hotplug state machine")
erroneously a positive number. Due to the "if (x) assume_error" construct
all callers assumed an error and as a consequence the cpu freq kworker
crashes with a NULL pointer dereference.
Reset the return value back to zero in the success case.
Fixes: 27622b061eb4 ("cpufreq: Convert to hotplug state machine")
Reported-by: Borislav Petkov <bp@alien8.de>
Reported-and-tested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: peterz@infradead.org
Cc: rjw@rjwysocki.net
Link: http://lkml.kernel.org/r/20160920145628.lp2bmq72ip3oiash@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Install the callbacks via the state machine.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Viresh Kumar <viresh.kumar@linaro.or
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160906170457.32393-13-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This patch fixes overflow issue when calculating the desired_perf.
Fixes: ad38677df44b (cpufreq: CPPC: Force reporting values in KHz to fix user space interface)
Signed-off-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Now that the cpufreq-dt-platdev is used to create the cpufreq-dt platform
device for all OMAP platforms and the platform code that did it
before has been removed, add ti,am33xx and ti,dra7xx to the machine list
in cpufreq-dt-platdev which had relied on the removed platform code to do
this previously.
Fixes: 7694ca6e1d6f (cpufreq: omap: Use generic platdev driver)
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.7+ <stable@vger.kernel.org> # 4.7+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add io_boost percent to current pstate_sample tracepoint.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Modify the P-state selection algorithm for Atom processors to use
the new SCHED_CPUFREQ_IOWAIT flag instead of the questionable
get_cpu_iowait_time_us() function.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When CPPC is being used by ACPI on arm64, user space tools such as
cpupower report CPU frequency values from sysfs that are incorrect.
What the driver was doing was reporting the values given by ACPI tables
in whatever scale was used to provide them. However, the ACPI spec
defines the CPPC values as unitless abstract numbers. Internal kernel
structures such as struct perf_cap, in contrast, expect these values
to be in KHz. When these struct values get reported via sysfs, the
user space tools also assume they are in KHz, causing them to report
incorrect values (for example, reporting a CPU frequency of 1MHz when
it should be 1.8GHz).
The downside is that this approach has some assumptions:
(1) It relies on SMBIOS3 being used, *and* that the Max Frequency
value for a processor is set to a non-zero value.
(2) It assumes that all processors run at the same speed, or that
the CPPC values have all been scaled to reflect relative speed.
This patch retrieves the largest CPU Max Frequency from a type 4 DMI
record that it can find. This may not be an issue, however, as a
sampling of DMI data on x86 and arm64 indicates there is often only
one such record regardless. Since CPPC is relatively new, it is
unclear if the ACPI ASL will always be written to reflect any sort
of relative performance of processors of differing speeds.
(3) It assumes that performance and frequency both scale linearly.
For arm64 servers, this may be sufficient, but it does rely on
firmware values being set correctly. Hence, other approaches will
be considered in the future.
This has been tested on three arm64 servers, with and without DMI, with
and without CPPC support.
Signed-off-by: Al Stone <ahs3@redhat.com>
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If a cpufreq driver is registered very early in the boot stage (e.g.
registered from postcore_initcall()), then cpufreq core may generate
kernel warnings for it.
In this case, the CPUs are brought online, then the cpufreq driver is
registered, and then the CPU topology devices are registered. However,
by the time cpufreq_add_dev() gets called, the cpu device isn't stored
in the per-cpu variable (cpu_sys_devices,) which is read by
get_cpu_device().
So the cpufreq core fails to get device for the CPU, for which
cpufreq_add_dev() was called in the first place and we will hit a
WARN_ON(!cpu_dev).
Even if we reuse the 'dev' parameter passed to cpufreq_add_dev() to
avoid that warning, there might be other CPUs online that share the
policy with the cpu for which cpufreq_add_dev() is called. Eventually
get_cpu_device() will return NULL for them as well, and we will hit the
same WARN_ON() again.
In order to fix these issues, change cpufreq core to create links to the
policy for a cpu only when cpufreq_add_dev() is called for that CPU.
Reuse the 'real_cpus' mask to track that as well.
Note that cpufreq_remove_dev() already handles removal of the links for
individual CPUs and cpufreq_add_dev() has aligned with that now.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
For structure types defined in the same file or local header files, find
top-level static structure declarations that have the following
properties:
1. Never reassigned.
2. Address never taken
3. Not passed to a top-level macro call
4. No pointer or array-typed field passed to a function or stored in a
variable.
Declare structures having all of these properties as const.
Done using Coccinelle.
Based on a suggestion by Joe Perches <joe@perches.com>.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The cpufreq-dt driver is also used for systems with multiple
clock/voltage domains for CPUs, i.e. multiple cpufreq policies in a
system.
And in such cases the platform users may want to enable "governor
tunables per policy". Support that via platform data, as not all users
of the driver would want that behavior.
Reported-by: Juri Lelli <Juri.Lelli@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The cpufreq DT driver also supports systems that have multiple
clock/voltage domains for CPUs, i.e. multiple policy systems.
The description of the Kconfig entry was never updated after the driver
was modified to support such systems, fix it.
Reported-by: Juri Lelli <Juri.Lelli@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This is leftover from an earlier patch which removed the usage of
platform data but forgot to remove this line. Remove it now.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add the compatible string for supporting the generic cpufreq driver on
the Renesas R-Car V2H (r8a7792) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
Since struct cpudata is defined in a header file, add prefix cppc_ to
make it not a generic name. Otherwise it causes compile issue in locally
define structure with the same name.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since cpufreq_policy_alloc() doesn't use its dev variable for
anything useful, drop that variable from there along with the
NULL check against it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Make sure of_device_id tables are NULL terminated.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Fixes: f56aad1d98f1 (cpufreq: dt: Add generic platform-device creation support)
CC: 4.7+ <stable@vger.kernel.org> # 4.7+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Compute the expected transition latency for frequency transitions
using the values from the PCCT tables when the desired perf
register is in PCC.
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Reviewed-by: Alexey Klimov <alexey.klimov@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Move the StrongARM CPU ID checks out of the platform's hardware.h
file into asm/cputype.h
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The field "owner" is set by the core.
Thus delete an unneeded initialisation.
Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
It is useful to know the reason why cpufreq_update_util() has just
been called and that can be passed as flags to cpufreq_update_util()
and to the ->func() callback in struct update_util_data. However,
doing that in addition to passing the util and max arguments they
already take would be clumsy, so avoid it.
Instead, use the observation that the schedutil governor is part
of the scheduler proper, so it can access scheduler data directly.
This allows the util and max arguments of cpufreq_update_util()
and the ->func() callback in struct update_util_data to be replaced
with a flags one, but schedutil has to be modified to follow.
Thus make the schedutil governor obtain the CFS utilization
information from the scheduler and use the "RT" and "DL" flags
instead of the special utilization value of ULONG_MAX to track
updates from the RT and DL sched classes. Make it non-modular
too to avoid having to export scheduler variables to modules at
large.
Next, update all of the other users of cpufreq_update_util()
and the ->func() callback in struct update_util_data accordingly.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
This patch adds the exynos5433 compatible string for supporting
the generic cpufreq driver on Exynos5433.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
* pm-sleep:
PM / hibernate: Restore processor state before using per-CPU variables
x86/power/64: Always create temporary identity mapping correctly
* pm-cpufreq:
cpufreq: powernv: Fix crash in gpstate_timer_handler()
|
|
Commit 09ca4c9b5958 (cpufreq: powernv: Replacing pstate_id with
frequency table index) changes calc_global_pstate() to use
cpufreq_table index instead of pstate_id.
But in gpstate_timer_handler(), pstate_id was being passed instead
of cpufreq_table index, which caused index_to_pstate() to access
out of bound indices, leading to this crash.
Adding sanity check for index and pstate, to ensure only valid pstate
and index values are returned.
Call Trace:
[c00000078d66b130] [c00000000011d224] __free_irq+0x234/0x360
(unreliable)
[c00000078d66b1c0] [c00000000011d44c] free_irq+0x6c/0xa0
[c00000078d66b1f0] [c00000000006c4f8] opal_event_shutdown+0x88/0xd0
[c00000078d66b230] [c000000000067a4c] opal_shutdown+0x1c/0x90
[c00000078d66b260] [c000000000063a00] pnv_shutdown+0x20/0x40
[c00000078d66b280] [c000000000021538] machine_restart+0x38/0x90
[c0000000078d66b310] [c000000000965ea0] panic+0x284/0x300
[c00000078d66b3a0] [c00000000001f508] die+0x388/0x450
[c00000078d66b430] [c000000000045a50] bad_page_fault+0xd0/0x140
[c00000078d66b4a0] [c000000000008964] handle_page_fault+0x2c/0x30
interrupt: 300 at gpstate_timer_handler+0x150/0x260
LR = gpstate_timer_handler+0x130/0x260
[c00000078d66b7f0] [c000000000132b58] call_timer_fn+0x58/0x1c0
[c00000078d66b880] [c000000000132e20] expire_timers+0x130/0x1d0
[c00000078d66b8f0] [c000000000133068] run_timer_softirq+0x1a8/0x230
[c00000078d66b980] [c0000000000b535c] __do_softirq+0x18c/0x400
[c00000078d66ba70] [c0000000000b5828] irq_exit+0xc8/0x100
[c00000078d66ba90] [c00000000001e214] timer_interrupt+0xa4/0xe0
[c00000078d66bac0] [c0000000000027d0] decrementer_common+0x150/0x180
interrupt: 901 at arch_local_irq_restore+0x74/0x90
0] [c000000000106b34] call_cpuidle+0x44/0x90
[c00000078d66be50] [c00000000010708c] cpu_startup_entry+0x38c/0x460
[c00000078d66bf20] [c00000000003d930] start_secondary+0x330/0x380
[c00000078d66bf90] [c000000000008e6c] start_secondary_prolog+0x10/0x14
Fixes: 09ca4c9b5958 (cpufreq: powernv: Replacing pstate_id with frequency table index)
Reported-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Akshay Adiga <akshay.adiga@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"A few more fixes and cleanups in the x86-64 low-level hibernation
code, PM core, cpufreq (Kconfig and intel_pstate), and the operating
points framework.
Specifics:
- Prevent the low-level assembly hibernate code on x86-64 from
referring to __PAGE_OFFSET directly as a symbol which doesn't work
when the kernel identity mapping base is randomized, in which case
__PAGE_OFFSET is a variable (Rafael Wysocki).
- Avoid selecting CPU_FREQ_STAT by default as the statistics are not
required for proper cpufreq operation (Borislav Petkov).
- Add Skylake-X and Broadwell-X IDs to the intel_pstate's list of
processors where out-of-band (OBB) control of P-states is possible
and if that is in use, intel_pstate should not attempt to manage
P-states (Srinivas Pandruvada).
- Drop some unnecessary checks from the wakeup IRQ handling code in
the PM core (Markus Elfring).
- Reduce the number operating performance point (OPP) lookups in one
of the OPP framework's helper functions (Jisheng Zhang)"
* tag 'pm-extra-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
x86/power/64: Do not refer to __PAGE_OFFSET from assembly code
cpufreq: Do not default-yes CPU_FREQ_STAT
cpufreq: intel_pstate: Add more out-of-band IDs
PM / OPP: optimize dev_pm_opp_set_rate() performance a bit
PM-wakeup: Delete unnecessary checks before three function calls
|
|
* pm-sleep:
x86/power/64: Do not refer to __PAGE_OFFSET from assembly code
* pm-cpufreq:
cpufreq: Do not default-yes CPU_FREQ_STAT
cpufreq: intel_pstate: Add more out-of-band IDs
* pm-core:
PM-wakeup: Delete unnecessary checks before three function calls
* pm-opp:
PM / OPP: optimize dev_pm_opp_set_rate() performance a bit
|
|
CPU frequency transition statistics are not absolutely required for
proper cpufreq operation on the system AFAICT so remove the default-yes
setting in Kconfig.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
|
|
Add Skylake-X and Broadwell-X IDs for out-of-band (OBB) control of
P-States.
For these processors, if MSR_MISC_PWR_MGMT BIT(8) == 1, then the
Intel P-State driver should exit as OS can't control P-States.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw : Subject/changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"Again, the majority of changes go into the cpufreq subsystem, but
there are no big features this time. The cpufreq changes that stand
out somewhat are the governor interface rework and improvements
related to the handling of frequency tables. Apart from those, there
are fixes and new device/CPU IDs in drivers, cleanups and an
improvement of the new schedutil governor.
Next, there are some changes in the hibernation core, including a fix
for a nasty problem related to the MONITOR/MWAIT usage by CPU offline
during resume from hibernation, a few core improvements related to
memory management during resume, a couple of additional debug features
and cleanups.
Finally, we have some fixes and cleanups in the devfreq subsystem,
generic power domains framework improvements related to system
suspend/resume, support for some new chips in intel_idle and in the
power capping RAPL driver, a new version of the AnalyzeSuspend utility
and some assorted fixes and cleanups.
Specifics:
- Rework the cpufreq governor interface to make it more
straightforward and modify the conservative governor to avoid using
transition notifications (Rafael Wysocki).
- Rework the handling of frequency tables by the cpufreq core to make
it more efficient (Viresh Kumar).
- Modify the schedutil governor to reduce the number of wakeups it
causes to occur in cases when the CPU frequency doesn't need to be
changed (Steve Muckle, Viresh Kumar).
- Fix some minor issues and clean up code in the cpufreq core and
governors (Rafael Wysocki, Viresh Kumar).
- Add Intel Broxton support to the intel_pstate driver (Srinivas
Pandruvada).
- Fix problems related to the config TDP feature and to the validity
of the MSR_HWP_INTERRUPT register in intel_pstate (Jan Kiszka,
Srinivas Pandruvada).
- Make intel_pstate update the cpu_frequency tracepoint even if the
frequency doesn't change to avoid confusing powertop (Rafael
Wysocki).
- Clean up the usage of __init/__initdata in intel_pstate, mark some
of its internal variables as __read_mostly and drop an unused
structure element from it (Jisheng Zhang, Carsten Emde).
- Clean up the usage of some duplicate MSR symbols in intel_pstate
and turbostat (Srinivas Pandruvada).
- Update/fix the powernv, s3c24xx and mvebu cpufreq drivers (Akshay
Adiga, Viresh Kumar, Ben Dooks).
- Fix a regression (introduced during the 4.5 cycle) in the
pcc-cpufreq driver by reverting the problematic commit (Andreas
Herrmann).
- Add support for Intel Denverton to intel_idle, clean up Broxton
support in it and make it explicitly non-modular (Jacob Pan, Jan
Beulich, Paul Gortmaker).
- Add support for Denverton and Ivy Bridge server to the Intel RAPL
power capping driver and make it more careful about the handing of
MSRs that may not be present (Jacob Pan, Xiaolong Wang).
- Fix resume from hibernation on x86-64 by making the CPU offline
during resume avoid using MONITOR/MWAIT in the "play dead" loop
which may lead to an inadvertent "revival" of a "dead" CPU and a
page fault leading to a kernel crash from it (Rafael Wysocki).
- Make memory management during resume from hibernation more
straightforward (Rafael Wysocki).
- Add debug features that should help to detect problems related to
hibernation and resume from it (Rafael Wysocki, Chen Yu).
- Clean up hibernation core somewhat (Rafael Wysocki).
- Prevent KASAN from instrumenting the hibernation core which leads
to large numbers of false-positives from it (James Morse).
- Prevent PM (hibernate and suspend) notifiers from being called
during the cleanup phase if they have not been called during the
corresponding preparation phase which is possible if one of the
other notifiers returns an error at that time (Lianwei Wang).
- Improve suspend-related debug printout in the tasks freezer and
clean up suspend-related console handling (Roger Lu, Borislav
Petkov).
- Update the AnalyzeSuspend script in the kernel sources to version
4.2 (Todd Brandt).
- Modify the generic power domains framework to make it handle system
suspend/resume better (Ulf Hansson).
- Make the runtime PM framework avoid resuming devices synchronously
when user space changes the runtime PM settings for them and
improve its error reporting (Rafael Wysocki, Linus Walleij).
- Fix error paths in devfreq drivers (exynos, exynos-ppmu,
exynos-bus) and in the core, make some devfreq code explicitly
non-modular and change some of it into tristate (Bartlomiej
Zolnierkiewicz, Peter Chen, Paul Gortmaker).
- Add DT support to the generic PM clocks management code and make it
export some more symbols (Jon Hunter, Paul Gortmaker).
- Make the PCI PM core code slightly more robust against possible
driver errors (Andy Shevchenko).
- Make it possible to change DESTDIR and PREFIX in turbostat (Andy
Shevchenko)"
* tag 'pm-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (89 commits)
Revert "cpufreq: pcc-cpufreq: update default value of cpuinfo_transition_latency"
PM / hibernate: Introduce test_resume mode for hibernation
cpufreq: export cpufreq_driver_resolve_freq()
cpufreq: Disallow ->resolve_freq() for drivers providing ->target_index()
PCI / PM: check all fields in pci_set_platform_pm()
cpufreq: acpi-cpufreq: use cached frequency mapping when possible
cpufreq: schedutil: map raw required frequency to driver frequency
cpufreq: add cpufreq_driver_resolve_freq()
cpufreq: intel_pstate: Check cpuid for MSR_HWP_INTERRUPT
intel_pstate: Update cpu_frequency tracepoint every time
cpufreq: intel_pstate: clean remnant struct element
PM / tools: scripts: AnalyzeSuspend v4.2
x86 / hibernate: Use hlt_play_dead() when resuming from hibernation
cpufreq: powernv: Replacing pstate_id with frequency table index
intel_pstate: Fix MSR_CONFIG_TDP_x addressing in core_get_max_pstate()
PM / hibernate: Image data protection during restoration
PM / hibernate: Add missing braces in __register_nosave_region()
PM / hibernate: Clean up comments in snapshot.c
PM / hibernate: Clean up function headers in snapshot.c
PM / hibernate: Add missing braces in hibernate_setup()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"This update provides the following changes:
- The rework of the timer wheel which addresses the shortcomings of
the current wheel (cascading, slow search for next expiring timer,
etc). That's the first major change of the wheel in almost 20
years since Finn implemted it.
- A large overhaul of the clocksource drivers init functions to
consolidate the Device Tree initialization
- Some more Y2038 updates
- A capability fix for timerfd
- Yet another clock chip driver
- The usual pile of updates, comment improvements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (130 commits)
tick/nohz: Optimize nohz idle enter
clockevents: Make clockevents_subsys static
clocksource/drivers/time-armada-370-xp: Fix return value check
timers: Implement optimization for same expiry time in mod_timer()
timers: Split out index calculation
timers: Only wake softirq if necessary
timers: Forward the wheel clock whenever possible
timers/nohz: Remove pointless tick_nohz_kick_tick() function
timers: Optimize collect_expired_timers() for NOHZ
timers: Move __run_timers() function
timers: Remove set_timer_slack() leftovers
timers: Switch to a non-cascading wheel
timers: Reduce the CPU index space to 256k
timers: Give a few structs and members proper names
hlist: Add hlist_is_singular_node() helper
signals: Use hrtimer for sigtimedwait()
timers: Remove the deprecated mod_timer_pinned() API
timers, net/ipv4/inet: Initialize connection request timers as pinned
timers, drivers/tty/mips_ejtag: Initialize the poll timer as pinned
timers, drivers/tty/metag_da: Initialize the poll timer as pinned
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 platform updates from Ingo Molnar:
"The main changes in this cycle were:
- Intel-SoC enhancements (Andy Shevchenko)
- Intel CPU symbolic model definition rework (Dave Hansen)
- ... other misc changes"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
x86/sfi: Enable enumeration of SD devices
x86/pci: Use MRFLD abbreviation for Merrifield
x86/platform/intel-mid: Make vertical indentation consistent
x86/platform/intel-mid: Mark regulators explicitly defined
x86/platform/intel-mid: Rename mrfl.c to mrfld.c
x86/platform/intel-mid: Enable spidev on Intel Edison boards
x86/platform/intel-mid: Extend PWRMU to support Penwell
x86/pci, x86/platform/intel_mid_pci: Remove duplicate power off code
x86/platform/intel-mid: Add pinctrl for Intel Merrifield
x86/platform/intel-mid: Enable GPIO expanders on Edison
x86/platform/intel-mid: Add Power Management Unit driver
x86/platform/atom/punit: Enable support for Merrifield
x86/platform/intel_mid_pci: Rework IRQ0 workaround
x86, thermal: Clean up and fix CPU model detection for intel_soc_dts_thermal
x86, mmc: Use Intel family name macros for mmc driver
x86/intel_telemetry: Use Intel family name macros for telemetry driver
x86/acpi/lss: Use Intel family name macros for the acpi_lpss driver
x86/cpufreq: Use Intel family name macros for the intel_pstate cpufreq driver
x86/platform: Use new Intel model number macros
x86/intel_idle: Use Intel family macros for intel_idle
...
|
