| Age | Commit message (Collapse) | Author |
|---|
|
This patch is modify code for stable working
1. Remove unused register access code
2. Change sequence for frequency changing
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
This patch is changes frequency table for cpu divider for stable frequency.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
This patch removes code for bus on cpufreq because the code
for bus frequency changing moves to busfreq driver.
So code about bus on cpufreq is not necessary.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
They're already consistent but it saves remembering to do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
This patch changes fields in cpustat from a structure, to an
u64 array. Math gets easier, and the code is more flexible.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul Tuner <pjt@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1322498719-2255-2-git-send-email-glommer@parallels.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into next
|
|
The variable i is removed by commit ded8433
"[CPUFREQ] db8500: remove unneeded for loop iteration over freq_table",
but current code to print available frequencies still uses the i variable.
Thus add the i variable back to fix below buld error:
CC drivers/cpufreq/db8500-cpufreq.o
drivers/cpufreq/db8500-cpufreq.c: In function 'db8500_cpufreq_init':
drivers/cpufreq/db8500-cpufreq.c:123: error: 'i' undeclared (first use in this function)
drivers/cpufreq/db8500-cpufreq.c:123: error: (Each undeclared identifier is reported only once
drivers/cpufreq/db8500-cpufreq.c:123: error: for each function it appears in.)
make[2]: *** [drivers/cpufreq/db8500-cpufreq.o] Error 1
make[1]: *** [drivers/cpufreq] Error 2
make: *** [drivers] Error 2
This patch also fixes using uninitialized i variable as array index.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
Minor fixups to work starting with v3.2:
- use the new omap_device API for getting a device by name.
- need to include <linux/module.h>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
We use a single frequency table for multiple CPUs. But, with
OMAP4, since we have multiple CPUs, the cpu_init call for CPU1
causes freq_table previously allocated for CPU0 to be overwritten.
In addition, we dont free the table on exit path.
We solve this by maintaining an atomic type counter to ensure
just a single table exists at a given time.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Release the mpu_clk in fail paths.
Reported-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
OMAP2 is the only family using clk_[init|exit]_cpufreq_table, however,
the cpufreq code does not currently use clk_init_cpufreq_table. As a
result, it is unusuable for OMAP2 and only usable only on platforms
using OPP library.
Remove the unbalanced clk_exit_cpufreq_table(). Any platforms where
OPPs are not availble will fail on init because a freq table will not
be properly initialized.
Signed-off-by: Nishanth Menon <nm@ti.com>
[khilman@ti.com: changelog edits, and graceful failure mode changes]
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
OMAP2+ all have frequency tables, hence the hacks we had for older
silicon do not need to be carried forward. As part of this change,
use cpufreq_frequency_table_target to find the best match for
frequency requested.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
if we do not have mpu_dev we normally fail in cpu_init. It is better
to fail driver registration if the devices are not available.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Clk name does'nt need to dynamically detected during clk init.
move them off to driver initialization, if we dont have a clk name,
there is no point in registering the driver anyways. The actual clk
get and put is left at cpu_init and exit functions.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Sometimes, bootloaders starts up with a frequency which is not
in the OPP table. At cpu_init, policy->cur contains the frequency
we pick at boot. It is possible that system might have fixed
it's boot frequency later on as part of power initialization.
After this condition, the first call to omap_target results in the
following:
omap_getspeed(actual device frequency) != policy->cur(frequency that
cpufreq thinks that the system is at), and it is possible that
freqs.old == freqs.new (because the governor requested a scale down).
We exit without triggering the notifiers in the current code, which
does'nt let code which depends on cpufreq_notify_transition to have
accurate information as to what the system frequency is.
Instead, we do a normal transition if policy->cur is wrong, then,
freqs.old will be the actual cpu frequency, freqs.new will be the
actual new cpu frequency and all required notifiers have the accurate
information.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Colin Cross <ccross@google.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Enable all CPUs in the shared policy in the CPU init callback.
Otherwise, the governor CPUFREQ_GOV_START event is invoked with
a policy that only includes the first CPU, leaving other CPUs
uninitialized by the governor.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
On OMAP SMP configuartion, both processors share the voltage
and clock. So both CPUs needs to be scaled together and hence
needs software co-ordination.
Also, update lpj with reference value to avoid progressive error.
Adjust _both_ the per-cpu loops_per_jiffy and global lpj. Calibrate
them with with reference to the initial values to avoid a
progressively bigger and bigger error in the value over time.
While at this, re-use the notifiers for UP/SMP since on UP machine or
UP_ON_SMP policy->cpus mask would contain only the boot CPU.
Based on initial SMP support by Santosh Shilimkar.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[khilman@ti.com: due to overlap/rework, combined original Santosh patch
and Russell's rework]
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Move OMAP cpufreq driver from arch/arm/mach-omap2 into
drivers/cpufreq, along with a few cleanups:
- generalize support for better handling of different SoCs in the OMAP
- use OPP layer instead of OMAP clock internals for frequency table init
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[khilman@ti.com: move to drivers]
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
|
|
* 'next' of git://github.com/kernelslacker/cpufreq:
[CPUFREQ] db8500: support all frequencies
[CPUFREQ] db8500: remove unneeded for loop iteration over freq_table
[CPUFREQ] ARM Exynos4210 PM/Suspend compatibility with different bootloaders
[CPUFREQ] ARM: ux500: send cpufreq notification for all cpus
[CPUFREQ] e_powersaver: Allow user to lower maximum voltage
[CPUFREQ] e_powersaver: Check BIOS limit for CPU frequency
[CPUFREQ] e_powersaver: Additional checks
[CPUFREQ] exynos4210: Show list of available frequencies
|
|
* 'for-next' of git://git.infradead.org/users/sameo/mfd-2.6: (80 commits)
mfd: Fix missing abx500 header file updates
mfd: Add missing <linux/io.h> include to intel_msic
x86, mrst: add platform support for MSIC MFD driver
mfd: Expose TurnOnStatus in ab8500 sysfs
mfd: Remove support for early drop ab8500 chip
mfd: Add support for ab8500 v3.3
mfd: Add ab8500 interrupt disable hook
mfd: Convert db8500-prcmu panic() into pr_crit()
mfd: Refactor db8500-prcmu request_clock() function
mfd: Rename db8500-prcmu init function
mfd: Fix db5500-prcmu defines
mfd: db8500-prcmu voltage domain consumers additions
mfd: db8500-prcmu reset code retrieval
mfd: db8500-prcmu tweak for modem wakeup
mfd: Add db8500-pcmu watchdog accessor functions for watchdog
mfd: hwacc power state db8500-prcmu accessor
mfd: Add db8500-prcmu accessors for PLL and SGA clock
mfd: Move to the new db500 PRCMU API
mfd: Create a common interface for dbx500 PRCMU drivers
mfd: Initialize DB8500 PRCMU regs
...
Fix up trivial conflicts in
arch/arm/mach-imx/mach-mx31moboard.c
arch/arm/mach-omap2/board-omap3beagle.c
arch/arm/mach-u300/include/mach/irqs.h
drivers/mfd/wm831x-spi.c
|
|
The header change has removed an implicit include of module.h, breaking
the build due to the use of THIS_MODULE. Fix that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
So that we can clean up the header files and not be relying
on implicit includes from device.h ---> module.h
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
This adds support for the 200 MHz frequency mode of the
DB8500 SoC, and prints the available frequencies at init
time.
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
Don't know why to do the loop iteration here. It looks unneeded.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
We have various bootloaders for Exynos4210 machines. Some of they
set the ARM core frequency at boot time even when the boot is a resume
from suspend-to-RAM. Such changes may create inconsistency in the
data of CPUFREQ driver and have incurred hang issues with suspend-to-RAM.
This patch enables to save and restore CPU frequencies with pm-notifier and
sets the frequency at the initial (boot-time) value so that there wouldn't
be any inconsistency between bootloader and kernel. This patch does not
use CPUFREQ's suspend/resume callbacks because they are syscore-ops, which
do not allow to use mutex that is being used by regulators that are used by
the target function.
This also prevents any CPUFREQ transitions during suspend-resume context,
which could be dangerous at noirq-context along with regulator framework.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
The same clock is used for all cpus so we must notify the frequency change
for each one in order to update the configuration of all twd clockevents.
change since V1:
* use policy->cpus instead of cpu_online_mask
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
Add new module option "set_max_voltage".
One of the lessons learned from Adaptive Powersaver is that voltage values
returned by processor are for worst case scenario. But required voltage
is changing with CPU temperature. And even processors produced in the same
batch can have different minimum voltage necessary for stable work at
specified frequency.
On Elonex Webbook, once system starts, temperature never drops below
48 deg. C. Loading module after systems start allows user to lower CPU
voltage and still have stable system.
Sadly C7 doesn't allow code to set frequency or voltage from outside limits.
If you ask it to set voltage lower then minimum it will ignore you. Thats
why it isn't possible to change minimum voltage for minimum frequency too.
Changing maximum voltage on Elonex Webbook leads to very good results. Looks
like VIA C7 1.6GHz 1084mV can safetly run at 892mV. This means 83% of
orginal value. If same percentage applies to power generated it means 12.5W
in the place of 15W. Not much, but it is better then nothing.
Only C7-M makes it possible.
If voltage is too low by 16mV or more you will experience kernel panic.
If voltage is too low by 32mV or more you will experience system freeze.
Signed-off-by: Rafał Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
Call ACPI function to get BIOS limit for CPU frequency.
Fail if processor would like to run at higher frequency.
Allow user to ignore BIOS limit.
eps: Detected VIA Model D C7-M
eps: Current voltage = 1084mV
eps: Current multiplier = 16
eps: Highest voltage = 1084mV
eps: Highest multiplier = 16
eps: Lowest voltage = 844mV
eps: Lowest multiplier = 4
eps: ACPI limit 1.60GHz
Signed-off-by: Rafał Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
Some systems are using 1,2Ghz@844mV processors running at 600MHz@796mV.
Try to detect such systems and don't touch anything on it. If CPU doesn't have
P-States in BIOS it should run at maximum frequency.
Allow user to bypass checks by means of two new options.
Don't set frequency to maximum on module unloading to avoid bada boom.
It is also possible that some processors may have incorrect values in min/max
registers caused by error in manufacturing process. Probably it would be BIOS
job to set them to right frequency and P-States tables would have correct
values inside.
Two additional sanity checks for voltage.
Signed-off-by: Rafał Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
This patch enables 'scaling_available_frequencies' attribute
showing list of available frequencies.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
time, s390: Get rid of compile warning
dw_apb_timer: constify clocksource name
time: Cleanup old CONFIG_GENERIC_TIME references that snuck in
time: Change jiffies_to_clock_t() argument type to unsigned long
alarmtimers: Fix error handling
clocksource: Make watchdog reset lockless
posix-cpu-timers: Cure SMP accounting oddities
s390: Use direct ktime path for s390 clockevent device
clockevents: Add direct ktime programming function
clockevents: Make minimum delay adjustments configurable
nohz: Remove "Switched to NOHz mode" debugging messages
proc: Consider NO_HZ when printing idle and iowait times
nohz: Make idle/iowait counter update conditional
nohz: Fix update_ts_time_stat idle accounting
cputime: Clean up cputime_to_usecs and usecs_to_cputime macros
alarmtimers: Rework RTC device selection using class interface
alarmtimers: Add try_to_cancel functionality
alarmtimers: Add more refined alarm state tracking
alarmtimers: Remove period from alarm structure
alarmtimers: Remove interval cap limit hack
...
|
|
Now that we have a shared API between the DB8500 and DB5500
PRCMU's, switch to using this neutral API instead. We delete the
parts of db8500-prcmu.h that is now PRCMU-neutral, and calls will
be diverted to respective driver. Common registers are in
dbx500-prcmu-regs.h and common accessors and defines in
<linux/mfd/dbx500-prcmu.h> This way we get a a lot more
abstraction and code reuse.
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Fast-forward merge with Linus to be able to merge patches
based on more recent version of the tree.
|
|
per_cpu(processors, n) can be NULL, resulting in:
Loading CPUFreq modules[ 437.661360] BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffffa0434314>] pcc_cpufreq_cpu_init+0x74/0x220 [pcc_cpufreq]
It's better to avoid the oops by failing the driver, and allowing the
system to boot.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Len Brown <lenb@kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
update_ts_time_stat currently updates idle time even if we are in
iowait loop at the moment. The only real users of the idle counter
(via get_cpu_idle_time_us) are CPU governors and they expect to get
cumulative time for both idle and iowait times.
The value (idle_sleeptime) is also printed to userspace by print_cpu
but it prints both idle and iowait times so the idle part is misleading.
Let's clean this up and fix update_ts_time_stat to account both counters
properly and update consumers of idle to consider iowait time as well.
If we do this we might use get_cpu_{idle,iowait}_time_us from other
contexts as well and we will get expected values.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Cc: Dave Jones <davej@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Link: http://lkml.kernel.org/r/e9c909c221a8da402c4da07e4cd968c3218f8eb1.1314172057.git.mhocko@suse.cz
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (135 commits)
drm/radeon/kms: fix DP training for DPEncoderService revision bigger than 1.1
drm/radeon/kms: add missing vddci setting on NI+
drm/radeon: Add a rmb() in IH processing
drm/radeon: ATOM Endian fix for atombios_crtc_program_pll()
drm/radeon: Fix the definition of RADEON_BUF_SWAP_32BIT
drm/radeon: Do an MMIO read on interrupts when not uisng MSIs
drm/radeon: Writeback endian fixes
drm/radeon: Remove a bunch of useless _iomem casts
drm/gem: add support for private objects
DRM: clean up and document parsing of video= parameter
DRM: Radeon: Fix section mismatch.
drm: really make debug levels match in edid failure code
drm/radeon/kms: fix i2c map for rv250/280
drm/nouveau/gr: disable fifo access and idle before suspend ctx unload
drm/nouveau: pass flag to engine fini() method on suspend
drm/nouveau: replace nv04_graph_fifo_access() use with direct reg bashing
drm/nv40/gr: rewrite/split context takedown functions
drm/nouveau: detect disabled device in irq handler and return IRQ_NONE
drm/nouveau: ignore connector type when deciding digital/analog on DVI-I
drm/nouveau: Add a quirk for Gigabyte NX86T
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (99 commits)
drivers/virt: add missing linux/interrupt.h to fsl_hypervisor.c
powerpc/85xx: fix mpic configuration in CAMP mode
powerpc: Copy back TIF flags on return from softirq stack
powerpc/64: Make server perfmon only built on ppc64 server devices
powerpc/pseries: Fix hvc_vio.c build due to recent changes
powerpc: Exporting boot_cpuid_phys
powerpc: Add CFAR to oops output
hvc_console: Add kdb support
powerpc/pseries: Fix hvterm_raw_get_chars to accept < 16 chars, fixing xmon
powerpc/irq: Quieten irq mapping printks
powerpc: Enable lockup and hung task detectors in pseries and ppc64 defeconfigs
powerpc: Add mpt2sas driver to pseries and ppc64 defconfig
powerpc: Disable IRQs off tracer in ppc64 defconfig
powerpc: Sync pseries and ppc64 defconfigs
powerpc/pseries/hvconsole: Fix dropped console output
hvc_console: Improve tty/console put_chars handling
powerpc/kdump: Fix timeout in crash_kexec_wait_realmode
powerpc/mm: Fix output of total_ram.
powerpc/cpufreq: Add cpufreq driver for Momentum Maple boards
powerpc: Correct annotations of pmu registration functions
...
Fix up trivial Kconfig/Makefile conflicts in arch/powerpc, drivers, and
drivers/cpufreq
|
|
Add simple cpufreq driver for Maple-based boards (ppc970fx evaluation
kit and others). Driver is based on a cpufreq driver for 64-bit powermac
boxes with all pmac-dependant features removed and simple cleanup
applied.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
ssh://master.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6 into drm-core-next
* 'drm-intel-next' of ssh://master.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6: (52 commits)
drm/i915: provide module parameter description
drm/i915: add module parameter compiler hints
drm/i915/bios: Avoid temporary allocation whilst searching for downclock
drm/i915: Cache GT fifo count for SandyBridge
i915: Fix opregion notifications
drm/i915: TVDAC_STATE_CHG does not indicate successful load-detect
drm/i915: Select correct pipe during TV detect
drm/i915/ringbuffer: Idling requires waiting for the ring to be empty
Revert "drm/i915: enable rc6 by default"
drm/i915: Clean up i915_driver_load failure path
drm/i915: Enable i915 frame buffer compression by default
drm/i915: Share the common work of disabling active FBC before updating
drm/i915: Perform intel_enable_fbc() from a delayed task
drm/i915: Disable FBC across page-flipping
drm/i915: Set persistent-mode for ILK/SNB framebuffer compression
drm/i915: Use of a CPU fence is mandatory to update FBC regions upon CPU writes
drm/i915: Remove vestigial pitch from post-gen2 FBC control routines
drm/i915: Replace direct calls to vfunc.disable_fbc with intel_disable_fbc()
drm/i915: Only export the generic intel_disable_fbc() interface
drm/i915: Enable GPU reset on Ivybridge.
...
|
|
The following symbols are needlessly defined global:
s5pv210_verify_speed
s5pv210_getspeed
Make them static.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
The following symbols are needlessly defined global:
exynos4_verify_speed
exynos4_getspeed
exynos4_set_clkdiv
Make them static.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
By extension from the 667MHz based clocks currently supported add 100MHz
and 200MHz operating points. Due to a lack of documentation these have not
been confirmed as supported but by extension from the existing frequencies
they should be OK, and I've given them quite a bit of runtime testing.
The major risk is synchronization with the non-ARM clocks but as we
can't currently scale the ARM PLL the risk should be relatively low.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
When system reboot, the CPUFREQ level should be 800MHz to prevent
system lockup.
Signed-off-by: Huisung Kang <hs1218.kang@samsung.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
Voltage scaling accesses the MAX8998 regulators over bit-banged I2C
with lots of udelays. In the case of decreasing CPU speed, the
number of loops per us for udelay needs to be adjusted prior to
decreasing voltage to avoid delaying for up to 10X too long.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
Without this lock the call to change the frequency for suspend could
switch to a new frequency while another thread was still changing the
cpu voltage.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
Minimum 800MHz is needed to enter/exit suspend mode due to voltage mismatch.
Signed-off-by: Huisung Kang <hs1218.kang@samsung.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
Relation has an additional symantics other than standard.
s5pv310_target funtion have below additional relation.
- DISABLE_FURTHER_CPUFREQ : disable further access to target
- ENABLE_FURTHER_CPUFRER : enable access to target
Signed-off-by: Huisung Kang <hs1218.kang@samsung.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
|
