| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
If frequency is throttled due to OCC reset then cpus will be in Psafe
frequency, so restore the frequency on all cpus to policy->cur when
OCCs are active again. And if frequency is throttled due to Pmax
capping then restore the frequency of all the cpus in the chip on
unthrottling.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
On a reset cycle of OCC, although the system retires from safe
frequency state the local pstate is not restored to Pmin or last
requested pstate. Now if the cpufreq governor initiates a pstate
change, the local pstate will be in Psafe and we will be reporting a
false positive when we are not throttled.
So in powernv_cpufreq_throttle_check() remove the condition which
checks if local pstate is less than Pmin while checking for Psafe
frequency. If the cpus are forced to Psafe then PMSR.psafe_mode_active
bit will be set. So, when OCCs become active this bit will be cleared.
Let us just rely on this bit for reporting throttling.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Re-evaluate the chip's throttled state on recieving OCC_THROTTLE
notification by executing *throttle_check() on any one of the cpu on
the chip. This is a sanity check to verify if we were indeed
throttled/unthrottled after receiving OCC_THROTTLE notification.
We cannot call *throttle_check() directly from the notification
handler because we could be handling chip1's notification in chip2. So
initiate an smp_call to execute *throttle_check(). We are irq-disabled
in the notification handler, so use a worker thread to smp_call
throttle_check() on any of the cpu in the chipmask.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
OCC is an On-Chip-Controller which takes care of power and thermal
safety of the chip. During runtime due to power failure or
overtemperature the OCC may throttle the frequencies of the CPUs to
remain within the power budget.
We want the cpufreq driver to be aware of such situations to be able
to report the reason to the user. We register to opal_message_notifier
to receive OCC messages from opal.
powernv_cpufreq_throttle_check() reports any frequency throttling and
this patch will report the reason or event that caused throttling. We
can be throttled if OCC is reset or OCC limits Pmax due to power or
thermal reasons. We are also notified of unthrottling after an OCC
reset or if OCC restores Pmax on the chip.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The On-Chip-Controller(OCC) can throttle cpu frequency by reducing the
max allowed frequency for that chip if the chip exceeds its power or
temperature limits. As Pmax capping is a chip level condition report
this throttling behavior at chip level and also do not set the global
'throttled' on Pmax capping instead set the per-chip throttled
variable. Report unthrottling if Pmax is restored after throttling.
This patch adds a structure to store chip id and throttled state of
the chip.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Change cpufreq_policy_alloc() to take a CPU number instead of a CPU
device pointer as its argument, as it is the only function called by
cpufreq_add_dev() taking a device pointer argument at this point.
That will allow us to split the CPU online part from cpufreq_add_dev()
more cleanly going forward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The related_cpus mask includes CPUs whose cpufreq_cpu_data per-CPU
pointers have been set the the given policy. Since those pointers
are only set at the policy creation time and unset when the policy
is deleted, the related_cpus should not be updated between those
two operations.
For this reason, avoid updating it whenever the first of the
"related" CPUs goes online.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The dev argument of cpufreq_add_policy_cpu() and
cpufreq_add_dev_interface() is not used by any of them,
so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The leftover out_release_rwsem label in cpufreq_add_dev() is not
necessary any more and confusing, so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Notice that when cpufreq_policy_restore() is called, its per-CPU
cpufreq_cpu_data variable has been already dereferenced and if that
variable is not NULL, the policy local pointer in cpufreq_add_dev()
contains its value.
Therefore it is not necessary to dereference it again and the
policy pointer can be used directly. Moreover, if that pointer
is not NULL, the policy is inactive (or the previous check would
have made us return from cpufreq_add_dev()) so the restoration
code from cpufreq_policy_restore() can be moved to that point
in cpufreq_add_dev().
Do that and drop cpufreq_policy_restore().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Since __cpufreq_remove_dev_prepare() and __cpufreq_remove_dev_finish()
are about CPU offline rather than about CPU removal, rename them to
cpufreq_offline_prepare() and cpufreq_offline_finish(), respectively.
Also change their argument from a struct device pointer to a CPU
number, because they use the CPU number only internally anyway
and make them void as their return values are ignored.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
|
|
After commit 87549141d516 (cpufreq: Stop migrating sysfs files on
hotplug) there is a problem with CPUs that share cpufreq policy
objects with other CPUs and are initially offline.
Say CPU1 shares a policy with CPU0 which is online and is registered
first. As part of the registration process, cpufreq_add_dev() is
called for it. It creates the policy object and a symbolic link
to it from the CPU1's sysfs directory. If CPU1 is registered
subsequently and it is offline at that time, cpufreq_add_dev() will
attempt to create a symbolic link to the policy object for it, but
that link is present already, so a warning about that will be
triggered.
To avoid that warning, make cpufreq use an additional CPU mask
containing related CPUs that are actually present for each policy
object. That mask is initialized when the policy object is populated
after its creation (for the first online CPU using it) and it includes
CPUs from the "policy CPUs" mask returned by the cpufreq driver's
->init() callback that are physically present at that time. Symbolic
links to the policy are created only for the CPUs in that mask.
If cpufreq_add_dev() is invoked for an offline CPU, it checks the
new mask and only creates the symlink if the CPU was not in it (the
CPU is added to the mask at the same time).
In turn, cpufreq_remove_dev() drops the given CPU from the new mask,
removes its symlink to the policy object and returns, unless it is
the CPU owning the policy object. In that case, the policy object
is moved to a new CPU's sysfs directory or deleted if the CPU being
removed was the last user of the policy.
While at it, notice that cpufreq_remove_dev() can't fail, because
its return value is ignored, so make it ignore return values from
__cpufreq_remove_dev_prepare() and __cpufreq_remove_dev_finish()
and prevent these functions from aborting on errors returned by
__cpufreq_governor(). Also drop the now unused sif argument from
them.
Fixes: 87549141d516 (cpufreq: Stop migrating sysfs files on hotplug)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reported-and-tested-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Scaling for Knights Landing is same as the default scaling (100000).
When Knigts Landing support was added to the pstate driver, this
parameter was omitted resulting in a kernel panic during boot.
Fixes: b34ef932d79a (intel_pstate: Knights Landing support)
Reported-by: Yasuaki Ishimatsu <yishimat@redhat.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Lukasz Anaczkowski <lukasz.anaczkowski@intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: 4.1+ <stable@vger.kernel.org> # 4.1+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
cpufreq_rwsem was introduced in commit 6eed9404ab3c4 ("cpufreq: Use
rwsem for protecting critical sections) in order to replace
try_module_get() on the cpu-freq driver. That try_module_get() worked
well until the refcount was so heavily used that module removal became
more or less impossible.
Though when looking at the various (undocumented) protection
mechanisms in that code, the randomly sprinkeled around cpufreq_rwsem
locking sites are superfluous.
The policy, which is acquired in cpufreq_cpu_get() and released in
cpufreq_cpu_put() is sufficiently protected already.
cpufreq_cpu_get(cpu)
/* Protects against concurrent driver removal */
read_lock_irqsave(&cpufreq_driver_lock, flags);
policy = per_cpu(cpufreq_cpu_data, cpu);
kobject_get(&policy->kobj);
read_unlock_irqrestore(&cpufreq_driver_lock, flags);
The reference on the policy serializes versus module unload already:
cpufreq_unregister_driver()
subsys_interface_unregister()
__cpufreq_remove_dev_finish()
per_cpu(cpufreq_cpu_data) = NULL;
cpufreq_policy_put_kobj()
If there is a reference held on the policy, i.e. obtained prior to the
unregister call, then cpufreq_policy_put_kobj() will wait until that
reference is dropped. So once subsys_interface_unregister() returns
there is no policy pointer in flight and no new reference can be
obtained. So that rwsem protection is useless.
The other usage of cpufreq_rwsem in show()/store() of the sysfs
interface is redundant as well because sysfs already does the proper
kobject_get()/put() pairs.
That leaves CPU hotplug versus module removal. The current
down_write() around the write_lock() in cpufreq_unregister_driver() is
silly at best as it protects actually nothing.
The trivial solution to this is to prevent hotplug across
cpufreq_unregister_driver completely.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Exynos5250 based platforms have switched over to use generic
cpufreq driver for cpufreq functionality. So the Exynos
specific cpufreq support for these platforms can be removed.
Cc: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[k.kozlowski: Rebased the patch around exynos-cpufreq.c]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
freq_table should be alloced in ->init and freed in ->exit, but it
it is not freed. Fix this memory leak in acpi_cpufreq_cpu_exit().
Signed-off-by: Pan Xinhui <xinhuix.pan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
freq_table is now stored as policy->freq_table, so drop the redundant
freq_table from struct cpufreq_acpi_io.
Signed-off-by: Pan Xinhui <xinhuix.pan@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The cpb sysfs attribute is only exposed by the ACPI cpufreq driver
after a runtime check. For this purpose, the driver keeps a NULL
placeholder in its table of sysfs attributes and replaces the NULL
with a pointer to an attribute structure if it decides to expose
cpb.
That is confusing, so make the driver set the pointer to the cpb
attribute structure upfront and replace it with NULL if the
attribute should not be exposed instead.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
After commit 8cfcfd39000d (acpi-cpufreq: Fix an ACPI perf unregister
issue) we store both a pointer to per-CPU data of the first policy
CPU and the number of that CPU which are redundant.
Since the CPU number has to be stored anyway for the unregistration,
the pointer to the CPU's per-CPU data may be dropped and we can
access the data in question via per_cpu_ptr().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
acpi_processor_unregister_performance() actually doesn't use its
first argument, so drop it and update the callers accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Return codes aren't honored properly in cpufreq_set_policy(). This can
lead to two problems:
- wrong errors propagated to sysfs
- we try to do next state-change even if the previous one failed
cpufreq_governor_dbs() now returns proper errors on all invalid
state-transition requests and this code should honor that.
Reviewed-and-tested-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
With previous commit, governors have started to return errors on invalid
state-transition requests. We already have a WARN for an invalid
state-transition request in cpufreq_governor_dbs(). This does trigger
today, as the sequence of events isn't guaranteed by cpufreq core.
Lets stop warning on that for now, and make sure we don't enter an
invalid state.
Reviewed-and-tested-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There can be races where the request has come to a wrong state. For
example INIT followed by STOP (instead of START) or START followed by
EXIT (instead of STOP).
Address these races by making sure the state-machine never gets into
any invalid state. Also return an error if an invalid state-transition
is requested.
Reviewed-and-tested-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some part of cs_dbs_timer() and od_dbs_timer() is exactly same and is
unnecessarily duplicated.
Create the real work-handler in cpufreq_governor.c and put the common
code in this routine (dbs_timer()).
Shouldn't make any functional change.
Reviewed-and-tested-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some information is common to all CPUs belonging to a policy, but are
kept on per-cpu basis. Lets keep that in another structure common to all
policy->cpus. That will make updates/reads to that less complex and less
error prone.
The memory for cpu_common_dbs_info is allocated/freed at INIT/EXIT, so
that it we don't reallocate it for STOP/START sequence. It will be also
be used (in next patch) while the governor is stopped and so must not be
freed that early.
Reviewed-and-tested-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Just call it 'policy', cur_policy is unnecessarily long and doesn't
have any special meaning.
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
It is called as 'cdbs' at most of the places and 'cpu_dbs' at others.
Lets use 'cdbs' consistently for better readability.
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Its not common info to all CPUs, but a structure representing common
type of cpu info to both governor types. Lets drop 'common_' from its
name.
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Its not used at all, drop it.
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Delayed work was named as 'work' and to access work within it we do
work.work. Not much readable. Rename delayed_work as 'dwork'.
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
HWP previously was only enabled at driver load time, on the boot
CPU, however, HWP must be enabled per package. Move the code to
enable HWP to the cpufreq driver init path so that it will be
called per CPU.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Tested-by: David Zhuang <david.zhuang@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Fixed coding style issues found by checkpatch.pl tool. Changed
space indentation to tab, removed unneccesary braces, removed
space between MODULE macros and parentheses.
REMARKS: failed to 'make' this file with error message
'fatal error: asm/mach-types.h: No such file or directory'.
Signed-off-by: Cristian Ardelean <cristian97.ardelean@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
As policy->cpu may not be same in acpi_cpufreq_cpu_init() and
acpi_cpufreq_cpu_exit(). There is a risk that we use different CPU
to un/register ACPI performance. So acpi_processor_unregister_performance()
may not be able to do the cleanup work. That causes a memory leak. And
if there will be another acpi_processor_register_performance() call,
it may also fail thanks to the internal check of pr->performace.
So add a new struct acpi_cpufreq_data field, acpi_perf_cpu, to fix
this issue.
Signed-off-by: Pan Xinhui <xinhuix.pan@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
cpufreq_init_policy() can fail, and we don't do anything except a call
to ->exit() on that. The policy should be freed if this happens.
Do it properly.
Reported-and-tested-by: "Jon Medhurst (Tixy)" <tixy@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
These labels are are named in two ways normally:
- Based on what caused to jump to such labels
- Based on what we do under such labels
We follow the first naming convention today and that leads to multiple
labels for doing the same work. Fix it by switching to the second way of
naming them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Drivers can store their internal per-policy information in
policy->driver_data, lets use it.
we have benefits after this replacing.
1) memory saving.
2) policy is shared by several cpus, per_cpu seems not correct. using
*driver_data* is more reasonable.
3) fix a memory leak in acpi_cpufreq_cpu_exit. as policy->cpu might
change during cpu hotplug. So sometimes we cant't free *data*, use
*driver_data* to fix it.
4) fix a zero return value of get_cur_freq_on_cpu. Only per_cpu of
policy->cpu is set to *data*, if we try to get cpufreq on other cpus, we
get zero instead of correct values. Use *driver_data* to fix it.
Signed-off-by: Pan Xinhui <xinhuix.pan@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
* pm-cpuidle:
suspend-to-idle: Prevent RCU from complaining about tick_freeze()
* pm-cpufreq:
cpufreq: Allow freq_table to be obtained for offline CPUs
cpufreq: Initialize the governor again while restoring policy
* acpi-resources:
ACPI / PCI: Fix regressions caused by resource_size_t overflow with 32-bit kernel
|
|
Add a new cpufreq driver for Tegra124. Instead of using the PLLX as
the CPU clocksource, switch immediately to the DFLL. It allows the use
of higher clock rates, and will automatically scale the CPU voltage as
well. Besides the CPU clocksource switch, we let the cpufreq-dt driver
for all the cpufreq operations.
This driver also relies on the DFLL driver to fill the OPP table for the
CPU0 device, so that the cpufreq-dt driver knows what frequencies to
use.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra124 will use a different driver for frequency scaling, so
rename the old driver (which handles only Tegra20) appropriately.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Users of freq table may want to access it for any CPU from
policy->related_cpus mask. One such user is cpu-cooling layer. It gets a
list of 'clip_cpus' (equivalent to policy->related_cpus) during
registration and tries to get freq_table for the first CPU of this mask.
If the CPU, for which it tries to fetch freq_table, is offline,
cpufreq_frequency_get_table() fails. This happens because it relies on
cpufreq_cpu_get_raw() for its functioning which returns policy only for
online CPUs.
The fix is to access the policy data structure for the given CPU
directly (which also returns a valid policy for offline CPUs), but the
policy itself has to be active (meaning that at least one CPU using it
is online) for the frequency table to be returned.
Because we will be using 'cpufreq_cpu_data' now, which is internal to
the cpufreq core, move cpufreq_frequency_get_table() to cpufreq.c.
Reported-and-tested-by: Pi-Cheng Chen <pi-cheng.chen@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When all CPUs of a policy are hot-unplugged, we EXIT the governor but
don't mark policy->governor as NULL. This was done in order to keep last
used governor's information intact in sysfs, while the CPUs are offline.
But we also need to clear policy->governor when restoring the policy.
Because policy->governor still points to the last governor while policy
is restored, following sequence of event happens:
- cpufreq_init_policy() called while restoring policy
- find_governor() matches last_governor string for present governors and
returns last used governor's pointer, say ondemand. policy->governor
already has the same address, unless the governor was removed in
between.
- cpufreq_set_policy() is called with both old/new policies governor set
as ondemand.
- Because governors matched, we skip governor initialization and return
after calling __cpufreq_governor(CPUFREQ_GOV_LIMITS). Because the
governor wasn't initialized for this policy, it returned -EBUSY.
- cpufreq_init_policy() exits the policy on this error, but doesn't
destroy it properly (should be fixed separately).
- And so we enter a scenario where the policy isn't completely
initialized but used.
Fix this by setting policy->governor to NULL while restoring the policy.
Reported-and-tested-by: Pi-Cheng Chen <pi-cheng.chen@linaro.org>
Reported-and-tested-by: "Jon Medhurst (Tixy)" <tixy@linaro.org>
Reported-and-tested-by: Steven Rostedt <rostedt@goodmis.org>
Fixes: 18bf3a124ef8 (cpufreq: Mark policy->governor = NULL for inactive policies)
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Now that there is no paravirt TSC, the "native" is
inappropriate. The function does RDTSC, so give it the obvious
name: rdtsc().
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Link: http://lkml.kernel.org/r/fd43e16281991f096c1e4d21574d9e1402c62d39.1434501121.git.luto@kernel.org
[ Ported it to v4.2-rc1. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull module_platform_driver replacement from Paul Gortmaker:
"Replace module_platform_driver with builtin_platform driver in non
modules.
We see an increasing number of non-modular drivers using
modular_driver() type register functions. There are several downsides
to letting this continue unchecked:
- The code can appear modular to a reader of the code, and they won't
know if the code really is modular without checking the Makefile
and Kconfig to see if compilation is governed by a bool or
tristate.
- Coders of drivers may be tempted to code up an __exit function that
is never used, just in order to satisfy the required three args of
the modular registration function.
- Non-modular code ends up including the <module.h> which increases
CPP overhead that they don't need.
- It hinders us from performing better separation of the module init
code and the generic init code.
So here we introduce similar macros for builtin drivers. Then we
convert builtin drivers (controlled by a bool Kconfig) by making the
following type of mapping:
module_platform_driver() ---> builtin_platform_driver()
module_platform_driver_probe() ---> builtin_platform_driver_probe().
The set of drivers that are converted here are just the ones that
showed up as relying on an implicit include of <module.h> during a
pending header cleanup. So we convert them here vs adding an include
of <module.h> to non-modular code to avoid compile fails. Additonal
conversions can be done asynchronously at any time.
Once again, an unused module_exit function that is removed here
appears in the diffstat as an outlier wrt all the other changes"
* tag 'module-builtin_driver-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
drivers/clk: convert sunxi/clk-mod0.c to use builtin_platform_driver
drivers/power: Convert non-modular syscon-reboot to use builtin_platform_driver
drivers/soc: Convert non-modular soc-realview to use builtin_platform_driver
drivers/soc: Convert non-modular tegra/pmc to use builtin_platform_driver
drivers/cpufreq: Convert non-modular s5pv210-cpufreq.c to use builtin_platform_driver
drivers/cpuidle: Convert non-modular drivers to use builtin_platform_driver
drivers/platform: Convert non-modular pdev_bus to use builtin_platform_driver
platform_device: better support builtin boilerplate avoidance
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull implicit module.h fixes from Paul Gortmaker:
"Fix up implicit <module.h> users that will break later.
The files changed here are simply modular source files that are
implicitly relying on <module.h> being present. We fix them up now,
so that we can decouple some of the module related init code from the
core init code in the future.
The addition of the module.h include to several files here is also a
no-op from a code generation point of view, else there would already
be compile issues with these files today.
There may be lots more implicit includes of <module.h> in tree, but
these are the ones that extensive build test coverage has shown that
must be fixed in order to avoid build breakage fallout for the pending
module.h <---> init.h code relocation we desire to complete"
* tag 'module-implicit-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
frv: add module.h to mb93090-mb00/flash.c to avoid compile fail
drivers/cpufreq: include <module.h> for modular exynos-cpufreq.c code
drivers/staging: include <module.h> for modular android tegra_ion code
crypto/asymmetric_keys: pkcs7_key_type needs module.h
sh: mach-highlander/psw.c is tristate and should use module.h
drivers/regulator: include <module.h> for modular max77802 code
drivers/pcmcia: include <module.h> for modular xxs1500_ss code
drivers/hsi: include <module.h> for modular omap_ssi code
drivers/gpu: include <module.h> for modular rockchip code
drivers/gpio: include <module.h> for modular crystalcove code
drivers/clk: include <module.h> for clk-max77xxx modular code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clock framework updates from Michael Turquette:
"The changes to the common clock framework for 4.2 are dominated by new
drivers and updates to existing ones, as usual.
There are some fixes to the framework itself and several cleanups for
sparse warnings, etc"
* tag 'clk-for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (135 commits)
clk: stm32: Add clock driver for STM32F4[23]xxx devices
dt-bindings: Document the STM32F4 clock bindings
cpufreq: exynos: remove Exynos4210 specific cpufreq driver support
ARM: Exynos: switch to using generic cpufreq driver for Exynos4210
clk: samsung: exynos4: add cpu clock configuration data and instantiate cpu clock
clk: samsung: add infrastructure to register cpu clocks
clk: add CLK_RECALC_NEW_RATES clock flag for Exynos cpu clock support
doc: dt: add documentation for lpc1850-ccu clk driver
clk: add lpc18xx ccu clk driver
doc: dt: add documentation for lpc1850-cgu clk driver
clk: add lpc18xx cgu clk driver
clk: keystone: add support for post divider register for main pll
clk: mvebu: flag the crypto clk as CLK_IGNORE_UNUSED
clk: cygnus: remove Cygnus dummy clock binding
clk: cygnus: add clock support for Broadcom Cygnus
clk: Change bcm clocks build dependency
clk: iproc: add initial common clock support
clk: iproc: define Broadcom iProc clock binding
MAINTAINERS: update email for Michael Turquette
clk: meson: add some error handling in meson_clk_register_cpu()
...
|
|
Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"The rework of backlight interface selection API from Hans de Goede
stands out from the number of commits and the number of affected
places perspective. The cpufreq core fixes from Viresh Kumar are
quite significant too as far as the number of commits goes and because
they should reduce CPU online/offline overhead quite a bit in the
majority of cases.
From the new featues point of view, the ACPICA update (to upstream
revision 20150515) adding support for new ACPI 6 material to ACPICA is
the one that matters the most as some new significant features will be
based on it going forward. Also included is an update of the ACPI
device power management core to follow ACPI 6 (which in turn reflects
the Windows' device PM implementation), a PM core extension to support
wakeup interrupts in a more generic way and support for the ACPI _CCA
device configuration object.
The rest is mostly fixes and cleanups all over and some documentation
updates, including new DT bindings for Operating Performance Points.
There is one fix for a regression introduced in the 4.1 cycle, but it
adds quite a number of lines of code, it wasn't really ready before
Thursday and you were on vacation, so I refrained from pushing it on
the last minute for 4.1.
Specifics:
- ACPICA update to upstream revision 20150515 including basic support
for ACPI 6 features: new ACPI tables introduced by ACPI 6 (STAO,
XENV, WPBT, NFIT, IORT), changes related to the other tables (DTRM,
FADT, LPIT, MADT), new predefined names (_BTH, _CR3, _DSD, _LPI,
_MTL, _PRR, _RDI, _RST, _TFP, _TSN), fixes and cleanups (Bob Moore,
Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation in
Windows (Rafael J Wysocki).
- rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling of
DMI quirks that may be involved in that and to make the code
generally more straightforward (Hans de Goede).
- fixes for the ACPI Embedded Controller (EC) driver related to the
handling of EC transactions (Lv Zheng).
- fix for a regression related to the ACPI resources management and
resulting from a recent change of ACPI initialization code ordering
(Rafael J Wysocki).
- fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the code
that switches the platform over to the ACPI mode too early in the
initialization sequence (Rafael J Wysocki).
- support for the ACPI _CCA device configuration object related to
DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- assorted cleanups related to ACPI (Dominik Brodowski, Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- fix for a long-standing issue causing General Protection Faults to
be generated occasionally on return to user space after resume from
ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- fix to make the suspend core code return -EBUSY consistently in all
cases when system suspend is aborted due to wakeup detection (Ruchi
Kandoi).
- support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- new tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- wakeup sources framework enhancements (Jin Qian).
- new macro for noirq system PM callbacks (Grygorii Strashko).
- assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should reduce
the overhead of these operations quite a bit, unless the CPU in
question is physically going away (Viresh Kumar, Saravana Kannan).
- serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- new Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- updates for the common clock operations support code in the PM core
(Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski)"
* tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (194 commits)
cpuidle: powernv/pseries: Auto-promotion of snooze to deeper idle state
x86: Load __USER_DS into DS/ES after resume
PM / OPP: Add binding for 'opp-suspend'
PM / OPP: Allow multiple OPP tables to be passed via DT
PM / OPP: Add new bindings to address shortcomings of existing bindings
ACPI: Constify ACPI device IDs in documentation
ACPI / enumeration: Document the rules regarding the PRP0001 device ID
ACPI / video: Make acpi_video_unregister_backlight() private
acpi-video-detect: Remove old API
toshiba-acpi: Port to new backlight interface selection API
thinkpad-acpi: Port to new backlight interface selection API
sony-laptop: Port to new backlight interface selection API
samsung-laptop: Port to new backlight interface selection API
msi-wmi: Port to new backlight interface selection API
msi-laptop: Port to new backlight interface selection API
intel-oaktrail: Port to new backlight interface selection API
ideapad-laptop: Port to new backlight interface selection API
fujitsu-laptop: Port to new backlight interface selection API
eeepc-laptop: Port to new backlight interface selection API
dell-wmi: Port to new backlight interface selection API
...
|
