| Age | Commit message (Collapse) | Author |
|---|
|
I'm leaving Red Hat at the end of December 2014, so remove all
references to my soon-to-be-dead address.
(There are some references left in the tree, that need additional
changes, I'll send those through the AGP maintainers).
Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There exists 350MHz K6-2E+ CPU, so add it to the usual frequency table.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
The cpufreq core now supports the cpufreq_for_each_entry and
cpufreq_for_each_valid_entry macros helpers for iteration over the
cpufreq_frequency_table, so use them.
It should have no functional changes.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
During frequency transitions, the cpufreq core takes the responsibility of
invoking cpufreq_freq_transition_begin() and cpufreq_freq_transition_end()
for those cpufreq drivers that define the ->target_index callback but don't
set the ASYNC_NOTIFICATION flag.
The powernow-k6 cpufreq driver falls under this category, but this driver was
invoking the _begin() and _end() APIs itself around frequency transitions,
which led to double invocation of the _begin() API. The _begin API makes
contending callers wait until the previous invocation is complete. Hence,
the powernow-k6 driver ended up waiting on itself, leading to system hangs
during boot.
Fix this by removing the calls to the _begin() and _end() APIs from the
powernow-k6 driver, since they rightly belong to the cpufreq core.
(Note that during ->exit(), the powernow-k6 driver sets the frequency
without any help from the cpufreq core. So add explicit calls to the
_begin() and _end() APIs around that frequency transition alone, to take
care of that special case. Also, add a missing 'break' statement there.)
Fixes: 12478cf0c55e (cpufreq: Make sure frequency transitions are serialized)
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The value of 'max_multiplier' is meant to be used for comparison with
clock_ratio[index].driver_data, not the index itself! Fix the code in
powernow_k6_cpu_exit() that has this bug.
Also, while at it, make the for-loop condition look for CPUFREQ_TABLE_END,
instead of hard-coding the loop count to 8.
Reported-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently cpufreq frequency table has two fields: frequency and driver_data.
driver_data is only for drivers' internal use and cpufreq core shouldn't use
it at all. But with the introduction of BOOST frequencies, this assumption
was broken and we started using it as a flag instead.
There are two problems due to this:
- It is against the description of this field, as driver's data is used by
the core now.
- if drivers fill it with -3 for any frequency, then those frequencies are
never considered by cpufreq core as it is exactly same as value of
CPUFREQ_BOOST_FREQ, i.e. ~2.
The best way to get this fixed is by creating another field flags which
will be used for such flags. This patch does that. Along with that various
drivers need modifications due to the change of struct cpufreq_frequency_table.
Reviewed-by: Gautham R Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
CPUFreq core has new infrastructure that would guarantee serialized calls to
target() or target_index() callbacks. These are called
cpufreq_freq_transition_begin() and cpufreq_freq_transition_end().
This patch converts existing drivers to use these new set of routines.
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
freq table is not per CPU but per policy, so it makes more sense to
keep it within struct cpufreq_policy instead of a per-cpu variable.
This patch does it. Over that, there is no need to set policy->freq_table
to NULL in ->exit(), as policy structure is going to be freed soon.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch reorders reported frequencies from the highest to the lowest,
just like in other frequency drivers.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The powernow-k6 driver used to read the initial multiplier from the
powernow register. However, there is a problem with this:
* If there was a frequency transition before, the multiplier read from the
register corresponds to the current multiplier.
* If there was no frequency transition since reset, the field in the
register always reads as zero, regardless of the current multiplier that
is set using switches on the mainboard and that the CPU is running at.
The zero value corresponds to multiplier 4.5, so as a consequence, the
powernow-k6 driver always assumes multiplier 4.5.
For example, if we have 550MHz CPU with bus frequency 100MHz and
multiplier 5.5, the powernow-k6 driver thinks that the multiplier is 4.5
and bus frequency is 122MHz. The powernow-k6 driver then sets the
multiplier to 4.5, underclocking the CPU to 450MHz, but reports the
current frequency as 550MHz.
There is no reliable way how to read the initial multiplier. I modified
the driver so that it contains a table of known frequencies (based on
parameters of existing CPUs and some common overclocking schemes) and sets
the multiplier according to the frequency. If the frequency is unknown
(because of unusual overclocking or underclocking), the user must supply
the bus speed and maximum multiplier as module parameters.
This patch should be backported to all stable kernels. If it doesn't
apply cleanly, change it, or ask me to change it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
I found out that a system with k6-3+ processor is unstable during network
server load. The system locks up or the network card stops receiving. The
reason for the instability is the CPU frequency scaling.
During frequency transition the processor is in "EPM Stop Grant" state.
The documentation says that the processor doesn't respond to inquiry
requests in this state. Consequently, coherency of processor caches and
bus master devices is not maintained, causing the system instability.
This patch flushes the cache during frequency transition. It fixes the
instability.
Other minor changes:
* u64 invalue changed to unsigned long because the variable is 32-bit
* move the logic to set the multiplier to a separate function
powernow_k6_set_cpu_multiplier
* preserve lower 5 bits of the powernow port instead of 4 (the voltage
field has 5 bits)
* mask interrupts when reading the multiplier, so that the port is not
open during other activity (running other kernel code with the port open
shouldn't cause any misbehavior, but we should better be safe and keep
the port closed)
This patch should be backported to all stable kernels. If it doesn't
apply cleanly, change it, or ask me to change it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently, the prototype of cpufreq_drivers target routines is:
int target(struct cpufreq_policy *policy, unsigned int target_freq,
unsigned int relation);
And most of the drivers call cpufreq_frequency_table_target() to get a valid
index of their frequency table which is closest to the target_freq. And they
don't use target_freq and relation after that.
So, it makes sense to just do this work in cpufreq core before calling
cpufreq_frequency_table_target() and simply pass index instead. But this can be
done only with drivers which expose their frequency table with cpufreq core. For
others we need to stick with the old prototype of target() until those drivers
are converted to expose frequency tables.
This patch implements the new light weight prototype for target_index() routine.
It looks like this:
int target_index(struct cpufreq_policy *policy, unsigned int index);
CPUFreq core will call cpufreq_frequency_table_target() before calling this
routine and pass index to it. Because CPUFreq core now requires to call routines
present in freq_table.c CONFIG_CPU_FREQ_TABLE must be enabled all the time.
This also marks target() interface as deprecated. So, that new drivers avoid
using it. And Documentation is updated accordingly.
It also converts existing .target() to newly defined light weight
.target_index() routine for many driver.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@rjwysocki.net>
|
|
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the powernow driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We don't need to set .owner = THIS_MODULE any more in cpufreq drivers
as this field isn't used any more by the cpufreq core.
This patch removes it and updates all dependent drivers accordingly.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The "index" field of struct cpufreq_frequency_table was never an
index and isn't used at all by the cpufreq core. It only is useful
for cpufreq drivers for their internal purposes.
Many people nowadays blindly set it in ascending order with the
assumption that the core will use it, which is a mistake.
Rename it to "driver_data" as that's what its purpose is. All of its
users are updated accordingly.
[rjw: Changelog]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
policy->cpus contains all online cpus that have single shared clock line. And
their frequencies are always updated together.
Many SMP system's cpufreq drivers take care of this in individual drivers but
the best place for this code is in cpufreq core.
This patch modifies cpufreq_notify_transition() to notify frequency change for
all cpus in policy->cpus and hence updates all users of this API.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit fa8031aefec0cf7ea6c2387c93610d99d9659aa2 ('cpufreq: Add support
for x86 cpuinfo auto loading v4') added a device ID table to this
driver, but didn't declare it as the module device ID table.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Thomas Renninger <trenn@suse.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This marks all the x86 cpuinfo tables to the CPU specific device drivers,
to allow auto loading by udev. This should simplify the distribution
startup scripts for this greatly.
I didn't add MODULE_DEVICE_IDs to the centrino and p4-clockmod drivers,
because those probably shouldn't be auto loaded and the acpi driver
be used instead (not fully sure on that, would appreciate feedback)
The old nforce drivers autoload based on the PCI ID.
ACPI cpufreq is autoloaded in another patch.
v3: Autoload gx based on PCI IDs only. Remove cpu check (Dave Jones)
v4: Use newly introduce HW_PSTATE feature for powernow-k8 loading
Cc: Dave Jones <davej@redhat.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Dave Jones <davej@redhat.com>
|
