| Age | Commit message (Collapse) | Author |
|---|
|
The 'caps' variable has been defined in cppc_cpufreq_khz_to_perf() and
cppc_cpufreq_perf_to_khz() routines, so there is no need to get
'highest_perf' value through 'cpu->caps.highest_perf', we can use
'caps->highest_perf' instead.
Signed-off-by: Xin Hao <xhao@linux.alibaba.com>
[ Viresh: Updated commit log ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
With the current approach we have an extra check in the
cppc_cpufreq_get_rate() callback, which checks if hisilicon's get rate
implementation should be used instead. While it works fine, the approach
isn't very straight forward, over that we have an extra check in the
routine.
Rearrange code and update the cpufreq driver's get() callback pointer
directly for the hisilicon case. This gets the extra variable is removed
and the extra check isn't required anymore as well.
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
To add SW BOOST support for CPPC, we need to get the max frequency of
boost mode and non-boost mode. ACPI spec 6.2 section 8.4.7.1 describes
the following two CPC registers.
"Highest performance is the absolute maximum performance an individual
processor may reach, assuming ideal conditions. This performance level
may not be sustainable for long durations, and may only be achievable if
other platform components are in a specific state; for example, it may
require other processors be in an idle state.
Nominal Performance is the maximum sustained performance level of the
processor, assuming ideal operating conditions. In absence of an
external constraint (power, thermal, etc.) this is the performance level
the platform is expected to be able to maintain continuously. All
processors are expected to be able to sustain their nominal performance
state simultaneously."
To add SW BOOST support for CPPC, we can use Highest Performance as the
max performance in boost mode and Nominal Performance as the max
performance in non-boost mode. If the Highest Performance is greater
than the Nominal Performance, we assume SW BOOST is supported.
The current CPPC driver does not support SW BOOST and use 'Highest
Performance' as the max performance the CPU can achieve. 'Nominal
Performance' is used to convert 'performance' to 'frequency'. That
means, if firmware enable boost and provide a value for Highest
Performance which is greater than Nominal Performance, boost feature is
enabled by default.
Because SW BOOST is disabled by default, so, after this patch, boost
feature is disabled by default even if boost is enabled by firmware.
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In the process of modifying a cpufreq policy, the cpufreq core makes
a copy of it including all of the internals which is stored on the
CPU stack. Because struct cpufreq_policy is relatively large, this
may cause the size of the stack frame to exceed the 2 KB limit and
so the GCC complains when -Wframe-larger-than= is used.
In fact, it is not necessary to copy the entire policy structure
in order to modify it, however.
First, because cpufreq_set_policy() obtains the min and max policy
limits from frequency QoS now, it is not necessary to pass the limits
to it from the callers. The only things that need to be passed to it
from there are the new governor pointer or (if there is a built-in
governor in the driver) the "policy" value representing the governor
choice. They both can be passed as individual arguments, though, so
make cpufreq_set_policy() take them this way and rework its callers
accordingly. This avoids making copies of cpufreq policies in the
callers of cpufreq_set_policy().
Second, cpufreq_set_policy() still needs to pass the new policy
data to the ->verify() callback of the cpufreq driver whose task
is to sanitize the min and max policy limits. It still does not
need to make a full copy of struct cpufreq_policy for this purpose,
but it needs to pass a few items from it to the driver in case they
are needed (different drivers have different needs in that respect
and all of them have to be covered). For this reason, introduce
struct cpufreq_policy_data to hold copies of the members of
struct cpufreq_policy used by the existing ->verify() driver
callbacks and pass a pointer to a temporary structure of that
type to ->verify() (instead of passing a pointer to full struct
cpufreq_policy to it).
While at it, notice that intel_pstate and longrun don't really need
to verify the "policy" value in struct cpufreq_policy, so drop those
check from them to avoid copying "policy" into struct
cpufreq_policy_data (which allows it to be slightly smaller).
Also while at it fix up white space in a couple of places and make
cpufreq_set_policy() static (as it can be so).
Fixes: 3000ce3c52f8 ("cpufreq: Use per-policy frequency QoS")
Link: https://lore.kernel.org/linux-pm/CAMuHMdX6-jb1W8uC2_237m8ctCpsnGp=JCxqt8pCWVqNXHmkVg@mail.gmail.com
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Put the ACPI table to release the table mapping after using it
successfully.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Bail out if we match the OEM information, to save some possible
extra iteration.
Also update the code to fix minor coding style issue.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 315 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.503150771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Hisilicon chips do not support delivered performance counter register
and reference performance counter register. But the platform can
calculate the real performance using its own method. We reuse the
desired performance register to store the real performance calculated by
the platform. After the platform finished the frequency adjust, it gets
the real performance and writes it into desired performance register. Os
can use it to calculate the real frequency.
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
[ rjw: Drop unnecessary braces ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Clang warns:
drivers/cpufreq/cppc_cpufreq.c:431:36: warning: variable 'cppc_acpi_ids'
is not needed and will not be emitted [-Wunneeded-internal-declaration]
static const struct acpi_device_id cppc_acpi_ids[] = {
^
1 warning generated.
Mark the definition as used so that Clang understands we don't want this
warning while not inhibiting Clang's dead code elimination from removing
the unreferenced internal symbol when moving the data it contains to the
globally available symbol via MODULE_DEVICE_TABLE.
$ nm -S drivers/cpufreq/cppc_cpufreq.o | grep acpi | tail -1
0000000000000000 0000000000000040 R __mod_acpi__cppc_acpi_ids_device_table
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Per Section 8.4.7.1.3 of ACPI 6.2, the platform provides performance
feedback via set of performance counters. To determine the actual
performance level delivered over time, OSPM may read a set of
performance counters from the Reference Performance Counter Register
and the Delivered Performance Counter Register.
OSPM calculates the delivered performance over a given time period by
taking a beginning and ending snapshot of both the reference and
delivered performance counters, and calculating:
delivered_perf = reference_perf X (delta of delivered_perf counter / delta of reference_perf counter).
Implement the above and hook this up to the cpufreq->get method.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The kzalloc() function has a 2-factor argument form, kcalloc(). This
patch replaces cases of:
kzalloc(a * b, gfp)
with:
kcalloc(a * b, gfp)
as well as handling cases of:
kzalloc(a * b * c, gfp)
with:
kzalloc(array3_size(a, b, c), gfp)
as it's slightly less ugly than:
kzalloc_array(array_size(a, b), c, gfp)
This does, however, attempt to ignore constant size factors like:
kzalloc(4 * 1024, gfp)
though any constants defined via macros get caught up in the conversion.
Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.
The Coccinelle script used for this was:
// Fix redundant parens around sizeof().
@@
type TYPE;
expression THING, E;
@@
(
kzalloc(
- (sizeof(TYPE)) * E
+ sizeof(TYPE) * E
, ...)
|
kzalloc(
- (sizeof(THING)) * E
+ sizeof(THING) * E
, ...)
)
// Drop single-byte sizes and redundant parens.
@@
expression COUNT;
typedef u8;
typedef __u8;
@@
(
kzalloc(
- sizeof(u8) * (COUNT)
+ COUNT
, ...)
|
kzalloc(
- sizeof(__u8) * (COUNT)
+ COUNT
, ...)
|
kzalloc(
- sizeof(char) * (COUNT)
+ COUNT
, ...)
|
kzalloc(
- sizeof(unsigned char) * (COUNT)
+ COUNT
, ...)
|
kzalloc(
- sizeof(u8) * COUNT
+ COUNT
, ...)
|
kzalloc(
- sizeof(__u8) * COUNT
+ COUNT
, ...)
|
kzalloc(
- sizeof(char) * COUNT
+ COUNT
, ...)
|
kzalloc(
- sizeof(unsigned char) * COUNT
+ COUNT
, ...)
)
// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@
(
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * (COUNT_ID)
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * COUNT_ID
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * (COUNT_CONST)
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * COUNT_CONST
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * (COUNT_ID)
+ COUNT_ID, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * COUNT_ID
+ COUNT_ID, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * (COUNT_CONST)
+ COUNT_CONST, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * COUNT_CONST
+ COUNT_CONST, sizeof(THING)
, ...)
)
// 2-factor product, only identifiers.
@@
identifier SIZE, COUNT;
@@
- kzalloc
+ kcalloc
(
- SIZE * COUNT
+ COUNT, SIZE
, ...)
// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@
(
kzalloc(
- sizeof(TYPE) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kzalloc(
- sizeof(TYPE) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kzalloc(
- sizeof(TYPE) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kzalloc(
- sizeof(TYPE) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
kzalloc(
- sizeof(THING) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kzalloc(
- sizeof(THING) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kzalloc(
- sizeof(THING) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
kzalloc(
- sizeof(THING) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
)
// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@
(
kzalloc(
- sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
kzalloc(
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
kzalloc(
- sizeof(THING1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
kzalloc(
- sizeof(THING1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
kzalloc(
- sizeof(TYPE1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
|
kzalloc(
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
)
// 3-factor product, only identifiers, with redundant parens removed.
@@
identifier STRIDE, SIZE, COUNT;
@@
(
kzalloc(
- (COUNT) * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- COUNT * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- COUNT * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- (COUNT) * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- COUNT * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- (COUNT) * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- (COUNT) * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
kzalloc(
- COUNT * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
)
// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression E1, E2, E3;
constant C1, C2, C3;
@@
(
kzalloc(C1 * C2 * C3, ...)
|
kzalloc(
- (E1) * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
|
kzalloc(
- (E1) * (E2) * E3
+ array3_size(E1, E2, E3)
, ...)
|
kzalloc(
- (E1) * (E2) * (E3)
+ array3_size(E1, E2, E3)
, ...)
|
kzalloc(
- E1 * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
)
// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@
(
kzalloc(sizeof(THING) * C2, ...)
|
kzalloc(sizeof(TYPE) * C2, ...)
|
kzalloc(C1 * C2 * C3, ...)
|
kzalloc(C1 * C2, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * (E2)
+ E2, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(TYPE) * E2
+ E2, sizeof(TYPE)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * (E2)
+ E2, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- sizeof(THING) * E2
+ E2, sizeof(THING)
, ...)
|
- kzalloc
+ kcalloc
(
- (E1) * E2
+ E1, E2
, ...)
|
- kzalloc
+ kcalloc
(
- (E1) * (E2)
+ E1, E2
, ...)
|
- kzalloc
+ kcalloc
(
- E1 * E2
+ E1, E2
, ...)
)
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
* acpi-cppc:
mailbox: PCC: erroneous error message when parsing ACPI PCCT
ACPI / CPPC: Fix invalid PCC channel status errors
ACPI / CPPC: Document CPPC sysfs interface
cpufreq / CPPC: Support for CPPC v3
ACPI / CPPC: Check for valid PCC subspace only if PCC is used
ACPI / CPPC: Add support for CPPC v3
* acpi-misc:
ACPI: Add missing prototype_for arch_post_acpi_subsys_init()
ACPI: add missing newline to printk
* acpi-battery:
ACPI / battery: Add quirk to avoid checking for PMIC with native driver
ACPI / battery: Ignore AC state in handle_discharging on systems where it is broken
ACPI / battery: Add handling for devices which wrongly report discharging state
ACPI / battery: Remove initializer for unused ident dmi_system_id
ACPI / AC: Remove initializer for unused ident dmi_system_id
* acpi-ac:
ACPI / AC: Add quirk to avoid checking for PMIC with native driver
|
|
Add support to specify platform specific transition_delay_us instead
of using the transition delay derived from PCC.
With commit 3d41386d556d (cpufreq: CPPC: Use transition_delay_us
depending transition_latency) we are setting transition_delay_us
directly and not applying the LATENCY_MULTIPLIER. Because of that,
on Qualcomm Centriq we can end up with a very high rate of frequency
change requests when using the schedutil governor (default
rate_limit_us=10 compared to an earlier value of 10000).
The PCC subspace describes the rate at which the platform can accept
commands on the CPPC's PCC channel. This includes read and write
command on the PCC channel that can be used for reasons other than
frequency transitions. Moreover the same PCC subspace can be used by
multiple freq domains and deriving transition_delay_us from it as we
do now can be sub-optimal.
Moreover if a platform does not use PCC for desired_perf register then
there is no way to compute the transition latency or the delay_us.
CPPC does not have a standard defined mechanism to get the transition
rate or the latency at the moment.
Given the above limitations, it is simpler to have a platform specific
transition_delay_us and rely on PCC derived value only if a platform
specific value is not available.
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Fixes: 3d41386d556d (cpufreq: CPPC: Use transition_delay_us depending transition_latency)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Use CPPC v3 entries to convert the abstract processor performance to
processor frequency in KHz.
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When multiple CPUs are related in one cpufreq policy, the first online
CPU will be chosen by default to handle cpufreq operations. Let's take
cpu0 and cpu1 as an example.
When cpu0 is offline, policy->cpu will be shifted to cpu1. cpu1's perf
capabilities should be initialized. Otherwise, perf capabilities are 0s
and speed change can not take effect.
This patch copies perf capabilities of the first online CPU to other
shared CPUs when policy shared type is CPUFREQ_SHARED_TYPE_ANY.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shunyong Yang <shunyong.yang@hxt-semitech.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Now that the driver has started to set transition_delay_us directly,
there is no need to set transition_latency along with it, as it is not
used by the cpufreq core.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
With commit e948bc8fbee0 (cpufreq: Cap the default transition delay
value to 10 ms) the cpufreq was not honouring the delay passed via
ACPI (PCCT). Due to which on ARM based platforms using CPPC the
cpufreq governor tries to change the frequency of CPUs faster than
expected.
This leads to continuous error messages like the following.
" ACPI CPPC: PCC check channel failed. Status=0 "
Earlier (without above commit) the default transition delay was
taken form the value passed from PCCT. Use the same value provided
by PCCT to set the transition_delay_us.
Fixes: e948bc8fbee0 (cpufreq: Cap the default transition delay value to 10 ms)
Signed-off-by: George Cherian <george.cherian@cavium.com>
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Kmemleak reported the below leak. When cppc_cpufreq_init went into
failure path, the cpu mask is not freed. After fix, this report is
gone. And to avaoid potential NULL pointer reference, check the cpu
value first.
unreferenced object 0xffff800fd5ea4880 (size 128):
comm "swapper/0", pid 1, jiffies 4294939510 (age 668.680s)
hex dump (first 32 bytes):
00 00 00 00 20 00 00 00 00 00 00 00 00 00 00 00 .... ...........
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffff0000082c4ae4>] __kmalloc_node+0x278/0x634
[<ffff0000088f4a74>] alloc_cpumask_var_node+0x28/0x60
[<ffff0000088f4af0>] zalloc_cpumask_var+0x14/0x1c
[<ffff000008d20254>] cppc_cpufreq_init+0xd0/0x19c
[<ffff000008083828>] do_one_initcall+0xec/0x15c
[<ffff000008cd1018>] kernel_init_freeable+0x1f4/0x2a4
[<ffff0000089099b0>] kernel_init+0x18/0x10c
[<ffff000008084d50>] ret_from_fork+0x10/0x18
[<ffffffffffffffff>] 0xffffffffffffffff
Signed-off-by: Chunyu Hu <chuhu@redhat.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
policy->cpu is copied into policy->cpus in cpufreq_online() before
calling into cpufreq_driver->init(). So there's no need to set the
same in the individual driver init() functions again.
This patch removes the redundant setting of policy->cpu in policy->cpus
in intel_pstate and cppc drivers.
Reported-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Description of Lowest Perfomance in ACPI 6.1 specification states:
"Lowest Performance is the absolute lowest performance level of
the platform. Selecting a performance level lower than the lowest
nonlinear performance level may actually cause an efficiency penalty,
but should reduce the instantaneous power consumption of the processor.
In traditional terms, this represents the T-state range of performance
levels."
Set the default value of policy->min to Lowest Nonlinear Performance
to avoid any potential efficiency penalty.
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Alexey Klimov <alexey.klimov@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
MODULE_DEVICE_TABLE is added so that CPPC cpufreq module can be
automatically loaded when we have a acpi processor device with
"ACPI0007" hid.
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"This includes a couple of fixes for cpufreq regressions introduced in
4.8, a rework of the intel_pstate algorithm used on Atom processors
(that took some time to test) plus a fix and a couple of cleanups in
that driver, a CPPC cpufreq driver fix, and a some devfreq fixes and
cleanups (core and exynos-nocp).
Specifics:
- Fix two cpufreq regressions causing undesirable changes in behavior
to appear (one in the core and one in the conservative governor)
introduced during the 4.8 cycle (Aaro Koskinen, Rafael Wysocki).
- Fix the way the intel_pstate driver accesses MSRs related to the
hardware-managed P-states (HWP) feature during the initialization
which currently is unsafe and may cause the processor to generate a
general protection fault (Srinivas Pandruvada).
- Rework the intel_pstate's P-state selection algorithm used on Atom
processors to avoid known problems with the current one and to make
the computation more straightforward, which also happens to improve
performance in multiple benchmarks a bit (Rafael Wysocki).
- Improve two comments in the intel_pstate driver (Rafael Wysocki).
- Fix the desired performance computation in the CPPC cpufreq driver
(Hoan Tran).
- Fix the devfreq core to avoid printing misleading error messages in
some cases (Tobias Jakobi).
- Fix the error code path in devfreq_add_device() to use proper
locking around list modifications (Axel Lin).
- Fix a build failure and remove a couple of redundant updates of
variables in the exynos-nocp devfreq driver (Axel Lin)"
* tag 'pm-extra-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: CPPC: Correct desired_perf calculation
cpufreq: conservative: Fix next frequency selection
cpufreq: skip invalid entries when searching the frequency
cpufreq: intel_pstate: Fix struct pstate_adjust_policy kerneldoc
cpufreq: intel_pstate: Proportional algorithm for Atom
PM / devfreq: Skip status update on uninitialized previous_freq
PM / devfreq: Add proper locking around list_del()
PM / devfreq: exynos-nocp: Remove redundant code
PM / devfreq: exynos-nocp: Select REGMAP_MMIO
cpufreq: intel_pstate: Clarify comment in get_target_pstate_use_performance()
cpufreq: intel_pstate: Fix unsafe HWP MSR access
|
|
The desired_perf is an abstract performance number. Its value should
be in the range of [lowest perf, highest perf] of CPPC.
The correct calculation is
desired_perf = freq * cppc_highest_perf / cppc_dmi_max_khz
And cppc_cpufreq_set_target() returns if desired_perf is exactly
the same with the old perf.
Signed-off-by: Hoan Tran <hotran@apm.com>
Reviewed-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"First off, the ACPICA code in the kernel is updated to upstream
revision 20160831 that brings in a few bug fixes and cleanups. In
particular, it is possible to mask GPEs now (and the sysfs interface
for GPE control is fixed on top of that), problems related to the
table loading mechanism are fixed and all code related to FADT version
2 (which has never been part of the ACPI specification) is dropped.
On the new features front, there is a new watchdog driver based on the
ACPI WDAT (ACPI Watchdog Action Table), needed on some platforms to
replace the iTCO watchdog that doesn't work there, and some UART
devices get new definitions of built-in properties (to be accessed via
the generic device properties API).
Also, included is a fix for an ACPI-related PCI resorces allocation
issue and a few problems in the EC driver and in the button and
battery drivers are fixed.
In addition to that, the ACPI CPPC library is updated to make batching
of requests sent over the PCC channel possible (which reduces the PCC
usage overhead substantially in some cases) and to support functional
fixed hardware (FFH) type of CPPC registers access (which will allow
CPPC to be used on x86 too in the future).
As usual, there are some assorted fixes and cleanups too.
Specifics:
- Update of the ACPICA code in the kernel to upstream revision
20160831 with the following major changes:
* New mechanism for GPE masking.
* Fixes for issues related to the LoadTable operator and table
loading.
* Fixes for issues related to so-called module-level code (MLC),
that is AML that doesn't belong to any methods.
* Change of the return value of the _OSI method to reflect the
Windows behavior.
* GAS (Generic Address Structure) support fix related to 32-bit
FADT addresses.
* Elimination of unnecessary FADT version 2 support.
* ACPI tools fixes and cleanups.
From Bob Moore, Lv Zheng, and Jung-uk Kim.
- ACPI sysfs interface updates to fix GPE handling (on top of the new
GPE masking mechanism in ACPICA) and issues related to table
loading (Lv Zheng).
- New watchdog driver based on the ACPI WDAT (ACPI Watchdog Action
Table), needed on some platforms to replace the iTCO watchdog that
doesn't work there and related updates of the intel_pmc_ipc,
i2c/i801 and MFD/lcp_ich drivers (Mika Westerberg).
- Driver core fix to prevent it from leaking secondary fwnode objects
during device removal (Lukas Wunner).
- New definitions of built-in properties for UART in ACPI-based x86
SoC drivers and a 8250_dw driver quirk for the APM X-Gene SoC
(Heikki Krogerus).
- New device ID for the Vulcan SPI controller and constification of
local strucures in the AMD SoC (APD) ACPI driver (Kamlakant Patel,
Julia Lawall).
- Fix for a bug causing the allocation of PCI resorces to fail if
ACPI-enumerated child platform devices are registered below the PCI
devices in question (Mika Westerberg).
- Change of the default polarity for PCI legacy IRQs to high on
systems booting wth ACPI on platforms with a GIC interrupt
controller model fixing the discrepancy between the specification
and HW behavior (Lorenzo Pieralisi).
- Fixes for the handling of system suspend/resume in the ACPI EC
driver and update of that driver to make it cope with the cases
when the EC device defined in the ECDT has to be used throughout
the entire system life cycle (Lv Zheng).
- Update of the ACPI CPPC library to allow it to batch requests sent
over the PCC channel (to reduce overhead), to support the fixed
functional hardware (FFH) CPPC registers access type, to notify the
mailbox framework about TX completions when the interrupt flag is
set for the PCC mailbox, and to support HW-Reduced Communication
Subspace type 2 (Ashwin Chaugule, Prashanth Prakash, Srinivas
Pandruvada, Hoan Tran).
- ACPI button driver fix and documentation update related to the
handling of laptop lids (Lv Zheng).
- ACPI battery driver initialization fix (Carlos Garnacho).
- ACPI GPIO enumeration documentation update (Mika Westerberg).
- Assorted updates of the core ACPI bus type code (Lukas Wunner, Lv
Zheng).
- Assorted cleanups of the ACPI table parsing code and the
x86-specific ACPI code (Al Stone).
- Fixes for assorted ACPI-related issues found in linux-next (Wei
Yongjun)"
* tag 'acpi-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (98 commits)
ACPI / documentation: Use recommended name in GPIO property names
watchdog: wdat_wdt: Fix warning for using 0 as NULL
watchdog: wdat_wdt: fix return value check in wdat_wdt_probe()
platform/x86: intel_pmc_ipc: Do not create iTCO watchdog when WDAT table exists
i2c: i801: Do not create iTCO watchdog when WDAT table exists
mfd: lpc_ich: Do not create iTCO watchdog when WDAT table exists
ACPI / bus: Adjust ACPI subsystem initialization for new table loading mode
ACPICA: Parser: Fix a regression in LoadTable support
ACPICA: Tables: Fix "UNLOAD" code path lock issues
ACPI / watchdog: Add support for WDAT hardware watchdog
ACPI / platform: Pay attention to parent device's resources
PCI: Add pci_find_resource()
ACPI / CPPC: Support PCC with interrupt flag
ACPI / sysfs: Update sysfs signature handling code
ACPI / sysfs: Fix an issue for LoadTable opcode
ACPICA: Tables: Fix a regression in acpi_tb_find_table()
ACPI / tables: Remove duplicated include from tables.c
ACPI / APD: constify local structures
x86: ACPI: make variable names clearer in acpi_parse_madt_lapic_entries()
x86: ACPI: remove extraneous white space after semicolon
...
|
|
This patch fixes overflow issue when calculating the desired_perf.
Fixes: ad38677df44b (cpufreq: CPPC: Force reporting values in KHz to fix user space interface)
Signed-off-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When CPPC is being used by ACPI on arm64, user space tools such as
cpupower report CPU frequency values from sysfs that are incorrect.
What the driver was doing was reporting the values given by ACPI tables
in whatever scale was used to provide them. However, the ACPI spec
defines the CPPC values as unitless abstract numbers. Internal kernel
structures such as struct perf_cap, in contrast, expect these values
to be in KHz. When these struct values get reported via sysfs, the
user space tools also assume they are in KHz, causing them to report
incorrect values (for example, reporting a CPU frequency of 1MHz when
it should be 1.8GHz).
The downside is that this approach has some assumptions:
(1) It relies on SMBIOS3 being used, *and* that the Max Frequency
value for a processor is set to a non-zero value.
(2) It assumes that all processors run at the same speed, or that
the CPPC values have all been scaled to reflect relative speed.
This patch retrieves the largest CPU Max Frequency from a type 4 DMI
record that it can find. This may not be an issue, however, as a
sampling of DMI data on x86 and arm64 indicates there is often only
one such record regardless. Since CPPC is relatively new, it is
unclear if the ACPI ASL will always be written to reflect any sort
of relative performance of processors of differing speeds.
(3) It assumes that performance and frequency both scale linearly.
For arm64 servers, this may be sufficient, but it does rely on
firmware values being set correctly. Hence, other approaches will
be considered in the future.
This has been tested on three arm64 servers, with and without DMI, with
and without CPPC support.
Signed-off-by: Al Stone <ahs3@redhat.com>
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since struct cpudata is defined in a header file, add prefix cppc_ to
make it not a generic name. Otherwise it causes compile issue in locally
define structure with the same name.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Compute the expected transition latency for frequency transitions
using the values from the PCCT tables when the desired perf
register is in PCC.
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Reviewed-by: Alexey Klimov <alexey.klimov@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add a function to cleanup at module exit and export
appropriate GPL string to enable moduler support
for the cppc_cpufreq driver.
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The CPU policy struct indicates the co-ordination type
for all CPUs of a common freq domain. Initialize it
correctly using the CPU specific data gathered from
CPPC ACPI lib via acpi_get_psd_map().
The PSD object is optional, so the cpu->shared_type
can also be 0. So instead of assuming any value other
than SW_ANY(0xFD) is unsupported, explictly check
if shared_type is SW_ALL and then bail.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This driver utilizes the methods introduced in a previous
patch titled - "ACPI: Introduce CPU performance controls using CPPC"
and enables usage with existing CPUFreq governors.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Reviewed-by: Al Stone <al.stone@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
