| Age | Commit message (Collapse) | Author |
|---|
|
CM_PLLx and A2W_XOSC_CTRL registers are accessed by different clock
handlers and must be accessed with ->regs_lock held.
Update the sections where this protection is missing.
Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the audio domain clocks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
ana->maskX values are already '~'-ed in bcm2835_pll_set_rate(). Remove
the '~' in the definition to fix ANA setup.
Note that this commit fixes a long standing bug preventing one from
using an HDMI display if it's plugged after the FW has booted Linux.
This is because PLLH is used by the HDMI encoder to generate the pixel
clock.
Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the audio domain clocks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
According to the Aspeed specification, the reset and enable sequence
should be done when the clock is stopped. The specification doesn't
define behavior if the reset is done while the clock is enabled.
From testing on the AST2500, the LPC Controller has problems if the
clock is reset while enabled.
Therefore, check whether the clock is enabled or not before performing
the reset and enable sequence in the Aspeed clock driver.
Reported-by: Lei Yu <mine260309@gmail.com>
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Fixes: 15ed8ce5f84e ("clk: aspeed: Register gated clocks")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Some of the Aspeed clocks are disabled by setting the relevant bit in
the "clock stop control" register to one, while others are disabled by
setting their bit to zero. The driver already uses a flag per gate to
identify this behavior, but doesn't apply it in the clock is_enabled
function.
Use the existing gate flag to correctly return whether or not a clock
is enabled in the aspeed_clk_is_enabled function.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Fixes: 6671507f0fbd ("clk: aspeed: Handle inverse polarity of USB port 1 clock gate")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
In case of error, the function dev_get_regmap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 81ac38847a1d ("clk: qcom: Add APCS clock controller support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
hi3660_stub_clk_probe()
platform_get_resource() may return NULL, add proper check to
avoid potential NULL dereferencing.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Fixes: 4f16f7ff3bc0 ("clk: hisilicon: Add support for Hi3660 stub clocks")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
* 'clk-helpers' (early part):
clk: fix determine rate error with pass-through clock
|
|
If we try to determine the rate of a pass-through clock (a clock which
does not implement .round_rate() nor .determine_rate()),
clk_core_round_rate_nolock() will directly forward the call to the
parent clock. In the particular case where the pass-through actually
does not have a parent, clk_core_round_rate_nolock() will directly
return 0 with the requested rate still set to the initial request
structure. This is interpreted as if the rate could be exactly achieved
while it actually cannot be adjusted.
This become a real problem when this particular pass-through clock is
the parent of a mux with the flag CLK_SET_RATE_PARENT set. The
pass-through clock will always report an exact match, get picked and
finally error when the rate is actually getting set.
This is fixed by setting the rate inside the req to 0 when core is NULL
in clk_core_round_rate_nolock() (same as in __clk_determine_rate() when
hw is NULL)
Fixes: 0f6cc2b8e94d ("clk: rework calls to round and determine rate callbacks")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
* clk-phase:
clk: update cached phase to respect the fact when setting phase
|
|
clk-fixes
Pull TI SoC clock fixes for 4.16 from Tero Kristo:
* tag 'ti-clk-fixes-4.16' of https://github.com/t-kristo/linux-pm:
clk: ti: am43xx: add set-rate-parent support for display clkctrl clock
clk: ti: am33xx: add set-rate-parent support for display clkctrl clock
clk: ti: clkctrl: add support for CLK_SET_RATE_PARENT flag
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-fixes
Pull i.MX clock fixes for 4.16 from Shawn Guo:
- Update i.MX5 clock driver to register UART4/5 clock only on i.MX50
and i.MX53. It fixes a kernel warning seen on i.MX53, caused by
commit 59dc3d8c8673 ("clk: imx51: uart4, uart5 gates only exist on
imx50, imx53").
* tag 'clk-imx-fixes-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
clk: imx51-imx53: Fix UART4/5 registration on i.MX50 and i.MX53
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-fixes
Pull Allwinner clock fixes for 4.16 from Chen-Yu Tsai:
A critical fix for the A31 sunxi-ng clock driver. The CLK_OUT clocks
had definitions paired with the incorrect type of clk ops. This results
in a serious oops starting with commit 946797aa3f08 ("clk: sunxi-ng:
Support fixed post-dividers on MP style clocks"), which exposed the
incorrect clk ops when it added a new field to the data structures,
which then nudged the underlying (compatible but incorrect) data
structures out of alignment.
* tag 'sunxi-clk-fixes-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: a31: Fix CLK_OUT_* clock ops
|
|
The orphan clocks reparents should migrate any existing count from the
orphan clock to its new acestor clocks, otherwise we may have
inconsistent counts in the tree and end-up with gated critical clocks
Assuming we have two clocks, A and B.
* Clock A has CLK_IS_CRITICAL flag set.
* Clock B is an ancestor of A which can gate. Clock B gate is left
enabled by the bootloader.
Step 1: Clock A is registered. Since it is a critical clock, it is
enabled. The clock being still an orphan, no parent are enabled.
Step 2: Clock B is registered and reparented to clock A (potentially
through several other clocks). We are now in situation where the enable
count of clock A is 1 while the enable count of its ancestors is 0, which
is not good.
Step 3: in lateinit, clk_disable_unused() is called, the enable_count of
clock B being 0, clock B is gated and and critical clock A actually gets
disabled.
This situation was found while adding fdiv_clk gates to the meson8b
platform. These clocks parent clk81 critical clock, which is the mother
of all peripheral clocks in this system. Because of the issue described
here, the system is crashing when clk_disable_unused() is called.
The situation is solved by reverting
commit f8f8f1d04494 ("clk: Don't touch hardware when reparenting during registration").
To avoid breaking again the situation described in this commit
description, enabling critical clock should be done before walking the
orphan list. This way, a parent critical clock may not be accidentally
disabled due to the CLK_OPS_PARENT_ENABLE mechanism.
Fixes: f8f8f1d04494 ("clk: Don't touch hardware when reparenting during registration")
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
|
|
It's found that the final phase set by driver doesn't match that of
the output from clk_summary:
dwmmc_rockchip fe310000.dwmmc: Successfully tuned phase to 346
mmc0: new ultra high speed SDR104 SDIO card at address 0001
cat /sys/kernel/debug/clk/clk_summary | grep sdio_sample
sdio_sample 0 1 0 50000000 0 0
It seems the cached core->phase isn't updated after the clk was
registered. So fix this issue by updating the core->phase if setting
phase successfully.
Fixes: 9e4d04adeb1a ("clk: add clk_core_set_phase_nolock function")
Cc: Stable <stable@vger.kernel.org>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
|
|
Display driver assumes it can use clk_set_rate for the display clock
via set-rate-parent mechanism, so add the flag for this to id.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Display driver assumes it can use clk_set_rate for the display clock
via set-rate-parent mechanism, so add the flag for this to it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
|
|
Certain clkctrl clocks, notably the display ones, use the
CLK_SET_RATE_PARENT feature extensively. Add support for this flag
to the clkctrl clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
|
|
Since commit 59dc3d8c8673 ("clk: imx51: uart4, uart5 gates only exist on
imx50, imx53") the following warnings are seen on i.MX53:
[ 2.776190] ------------[ cut here ]------------
[ 2.780948] WARNING: CPU: 0 PID: 1 at ../drivers/clk/clk.c:811 clk_core_disable+0xc4/0xe0
[ 2.789145] Modules linked in:
[ 2.792236] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.15.0-rc7-next-20180115 #1
[ 2.799735] Hardware name: Freescale i.MX53 (Device Tree Support)
[ 2.805845] Backtrace:
[ 2.808329] [<c010d1a0>] (dump_backtrace) from [<c010d460>] (show_stack+0x18/0x1c)
[ 2.815919] r7:00000000 r6:60000093 r5:00000000 r4:c10798d4
[ 2.821607] [<c010d448>] (show_stack) from [<c0a353ec>] (dump_stack+0xb4/0xe8)
[ 2.828854] [<c0a35338>] (dump_stack) from [<c0126144>] (__warn+0xf0/0x11c)
[ 2.835837] r9:00000000 r8:0000032b r7:00000009 r6:c0d429f8 r5:00000000 r4:00000000
[ 2.843601] [<c0126054>] (__warn) from [<c0126288>] (warn_slowpath_null+0x44/0x50)
[ 2.851191] r8:c1008908 r7:c0e08874 r6:c04bfac8 r5:0000032b r4:c0d429f8
[ 2.857913] [<c0126244>] (warn_slowpath_null) from [<c04bfac8>] (clk_core_disable+0xc4/0xe0)
[ 2.866369] r6:dc02bb00 r5:dc02a980 r4:dc02a980
[ 2.871011] [<c04bfa04>] (clk_core_disable) from [<c04c0e54>] (clk_core_disable_lock+0x20/0x2c)
[ 2.879726] r5:dc02a980 r4:80000013
[ 2.883323] [<c04c0e34>] (clk_core_disable_lock) from [<c04c0e84>] (clk_disable+0x24/0x28)
[ 2.891604] r5:c0f6b3e4 r4:0000001c
[ 2.895209] [<c04c0e60>] (clk_disable) from [<c0f2340c>] (imx_clk_disable_uart+0x50/0x68)
[ 2.903412] [<c0f233bc>] (imx_clk_disable_uart) from [<c010277c>] (do_one_initcall+0x50/0x19c)
[ 2.912043] r7:c0e08874 r6:c0f63854 r5:c0f233bc r4:ffffe000
[ 2.917726] [<c010272c>] (do_one_initcall) from [<c0f00f00>] (kernel_init_freeable+0x118/0x1d0)
[ 2.926447] r9:c0f63858 r8:000000f0 r7:c0e08874 r6:c0f63854 r5:c107b500 r4:c0f75260
[ 2.934220] [<c0f00de8>] (kernel_init_freeable) from [<c0a4a5f0>] (kernel_init+0x10/0x118)
[ 2.942506] r10:00000000 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c0a4a5e0
[ 2.950351] r4:00000000
[ 2.952908] [<c0a4a5e0>] (kernel_init) from [<c01010b4>] (ret_from_fork+0x14/0x20)
[ 2.960496] Exception stack(0xdc05dfb0 to 0xdc05dff8)
[ 2.965569] dfa0: 00000000 00000000 00000000 00000000
[ 2.973768] dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 2.981965] dfe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 2.988596] r5:c0a4a5e0 r4:00000000
[ 2.992188] ---[ end trace 346e26f708876edd ]---
[ 2.997420] ------------[ cut here ]------------
In order to fix the problem UART4/5 registration needs to happen only on
i.MX50 and i.MX53.
So let mx51_clocks_init() register only UART1-3 and
mx50_clocks_init()/mx53_clocks_init register all the UART1-5 ports.
Fixes: 59dc3d8c8673 ("clk: imx51: uart4, uart5 gates only exist on imx50, imx53")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
When support for the A31/A31s CCU was first added, the clock ops for
the CLK_OUT_* clocks was set to the wrong type. The clocks are MP-type,
but the ops was set for div (M) clocks. This went unnoticed until now.
This was because while they are different clocks, their data structures
aligned in a way that ccu_div_ops would access the second ccu_div_internal
and ccu_mux_internal structures, which were valid, if not incorrect.
Furthermore, the use of these CLK_OUT_* was for feeding a precise 32.768
kHz clock signal to the WiFi chip. This was achievable by using the parent
with the same clock rate and no divider. So the incorrect divider setting
did not affect this usage.
Commit 946797aa3f08 ("clk: sunxi-ng: Support fixed post-dividers on MP
style clocks") added a new field to the ccu_mp structure, which broke
the aforementioned alignment. Now the system crashes as div_ops tries
to look up a nonexistent table.
Reported-by: Philipp Rossak <embed3d@gmail.com>
Tested-by: Philipp Rossak <embed3d@gmail.com>
Fixes: c6e6c96d8fa6 ("clk: sunxi-ng: Add A31/A31s clocks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS updates from James Hogan:
"These are the main MIPS changes for 4.16.
Rough overview:
(1) Basic support for the Ingenic JZ4770 based GCW Zero open-source
handheld video game console
(2) Support for the Ranchu board (used by Android emulator)
(3) Various cleanups and misc improvements
More detailed summary:
Fixes:
- Fix generic platform's USB_*HCI_BIG_ENDIAN selects (4.9)
- Fix vmlinuz default build when ZBOOT selected
- Fix clean up of vmlinuz targets
- Fix command line duplication (in preparation for Ingenic JZ4770)
Miscellaneous:
- Allow Processor ID reads to be to be optimised away by the compiler
(improves performance when running in guest)
- Push ARCH_MIGHT_HAVE_PC_SERIO/PARPORT down to platform level to
disable on generic platform with Ranchu board support
- Add helpers for assembler macro instructions for older assemblers
- Use assembler macro instructions to support VZ, XPA & MSA
operations on older assemblers, removing C wrapper duplication
- Various improvements to VZ & XPA assembly wrappers
- Add drivers/platform/mips/ to MIPS MAINTAINERS entry
Minor cleanups:
- Misc FPU emulation cleanups (removal of unnecessary include, moving
macros to common header, checkpatch and sparse fixes)
- Remove duplicate assignment of core in play_dead()
- Remove duplication in watchpoint handling
- Remove mips_dma_mapping_error() stub
- Use NULL instead of 0 in prepare_ftrace_return()
- Use proper kernel-doc Return keyword for
__compute_return_epc_for_insn()
- Remove duplicate semicolon in csum_fold()
Platform support:
Broadcom:
- Enable ZBOOT on BCM47xx
Generic platform:
- Add Ranchu board support, used by Android emulator
- Fix machine compatible string matching for Ranchu
- Support GIC in EIC mode
Ingenic platforms:
- Add DT, defconfig and other support for JZ4770 SoC and GCW Zero
- Support dynamnic machine types (i.e. JZ4740 / JZ4770 / JZ4780)
- Add Ingenic JZ4770 CGU clocks
- General Ingenic clk changes to prepare for JZ4770 SoC support
- Use common command line handling code
- Add DT vendor prefix to GCW (Game Consoles Worldwide)
Loongson:
- Add MAINTAINERS entry for Loongson2 and Loongson3 platforms
- Drop 32-bit support for Loongson 2E/2F devices
- Fix build failures due to multiple use of 'MEM_RESERVED'"
* tag 'mips_4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips: (53 commits)
MIPS: Malta: Sanitize mouse and keyboard configuration.
MIPS: Update defconfigs after previous patch.
MIPS: Push ARCH_MIGHT_HAVE_PC_SERIO down to platform level
MIPS: Push ARCH_MIGHT_HAVE_PC_PARPORT down to platform level
MIPS: SMP-CPS: Remove duplicate assignment of core in play_dead
MIPS: Generic: Support GIC in EIC mode
MIPS: generic: Fix Makefile alignment
MIPS: generic: Fix ranchu_of_match[] termination
MIPS: generic: Fix machine compatible matching
MIPS: Loongson fix name confict - MEM_RESERVED
MIPS: bcm47xx: enable ZBOOT support
MIPS: Fix trailing semicolon
MIPS: Watch: Avoid duplication of bits in mips_read_watch_registers
MIPS: Watch: Avoid duplication of bits in mips_install_watch_registers.
MIPS: MSA: Update helpers to use new asm macros
MIPS: XPA: Standardise readx/writex accessors
MIPS: XPA: Allow use of $0 (zero) to MTHC0
MIPS: XPA: Use XPA instructions in assembly
MIPS: VZ: Pass GC0 register names in $n format
MIPS: VZ: Update helpers to use new asm macros
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The core framework has a handful of patches this time around, mostly
due to the clk rate protection support added by Jerome Brunet.
This feature will allow consumers to lock in a certain rate on the
output of a clk so that things like audio playback don't hear pops
when the clk frequency changes due to shared parent clks changing
rates. Currently the clk API doesn't guarantee the rate of a clk stays
at the rate you request after clk_set_rate() is called, so this new
API will allow drivers to express that requirement.
Beyond this, the core got some debugfs pretty printing patches and a
couple minor non-critical fixes.
Looking outside of the core framework diff we have some new driver
additions and the removal of a legacy TI clk driver. Both of these hit
high in the dirstat. Also, the removal of the asm-generic/clkdev.h
file causes small one-liners in all the architecture Kbuild files.
Overall, the driver diff seems to be the normal stuff that comes all
the time to fix little problems here and there and to support new
hardware.
Summary:
Core:
- Clk rate protection
- Symbolic clk flags in debugfs output
- Clk registration enabled clks while doing bookkeeping updates
New Drivers:
- Spreadtrum SC9860
- HiSilicon hi3660 stub
- Qualcomm A53 PLL, SPMI clkdiv, and MSM8916 APCS
- Amlogic Meson-AXG
- ASPEED BMC
Removed Drivers:
- TI OMAP 3xxx legacy clk (non-DT) support
- asm*/clkdev.h got removed (not really a driver)
Updates:
- Renesas FDP1-0 module clock on R-Car M3-W
- Renesas LVDS module clock on R-Car V3M
- Misc fixes to pr_err() prints
- Qualcomm MSM8916 audio fixes
- Qualcomm IPQ8074 rounded out support for more peripherals
- Qualcomm Alpha PLL variants
- Divider code was using container_of() on bad pointers
- Allwinner DE2 clks on H3
- Amlogic minor data fixes and dropping of CLK_IGNORE_UNUSED
- Mediatek clk driver compile test support
- AT91 PMC clk suspend/resume restoration support
- PLL issues fixed on si5351
- Broadcom IProc PLL calculation updates
- DVFS support for Armada mvebu CPU clks
- Allwinner fixed post-divider support
- TI clkctrl fixes and support for newer SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (125 commits)
clk: aspeed: Handle inverse polarity of USB port 1 clock gate
clk: aspeed: Fix return value check in aspeed_cc_init()
clk: aspeed: Add reset controller
clk: aspeed: Register gated clocks
clk: aspeed: Add platform driver and register PLLs
clk: aspeed: Register core clocks
clk: Add clock driver for ASPEED BMC SoCs
clk: mediatek: adjust dependency of reset.c to avoid unexpectedly being built
clk: fix reentrancy of clk_enable() on UP systems
clk: meson-axg: fix potential NULL dereference in axg_clkc_probe()
clk: Simplify debugfs registration
clk: Fix debugfs_create_*() usage
clk: Show symbolic clock flags in debugfs
clk: renesas: r8a7796: Add FDP clock
clk: Move __clk_{get,put}() into private clk.h API
clk: sunxi: Use CLK_IS_CRITICAL flag for critical clks
clk: Improve flags doc for of_clk_detect_critical()
arch: Remove clkdev.h asm-generic from Kbuild
clk: sunxi-ng: a83t: Add M divider to TCON1 clock
clk: Prepare to remove asm-generic/clkdev.h
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"We get a moderate number of new machines this time, and only one new
SoC variant (Actions S700):
Actions:
- S700 Soc and CubieBoard7 development board
- Allo.com Sparky Single-board-computer
Allwinner:
- Orange Pi R1 development board
- Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
- Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
- Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
- Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
- Axentia Nattis/Natte digital signage
- sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
- SolidRun Humminboard2 development board
- Variscite DART-MX6 SoM and Carrier-board
- Technologic TS-4600 and TS-7970 development board
- Toradex Colibri iMX7D SoM board
- v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
- Moxa UC-8410A Series industrial computer
Gemini:
- D-Link DNS-313 NAS enclosure
OMAP:
- LogicPD OMAP35xx SOM-LV devkit
- LogicPD OMAP35xx Torpedo devkit
Renesas:
- r8a77970 (V3M) Starter Kit board
- r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
- Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
- Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
- Aspeed clk controller support
- Freescale LS1088A, LS1021A device support
- Gemini Ethernet, PCI, TVE, panel
- Keystone gpio, qspi, more uarts
- Mediatek cpufreq, regulator, clock, reset
- Marvell thermal, cpufreq, nand
- Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
- Rockchip Mipi, GPU, display
- Samsung Exynos5433 PMU, power domain, nfc
- Spreadtrum: sc9860 clocks
- Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ..."
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (690 commits)
arm64: dts: stratix10: fix SPI settings
ARM: dts: socfpga: add i2c reset signals
arm64: dts: stratix10: add USB ECC reset bit
arm64: dts: stratix10: enable USB on the devkit
ARM: dts: socfpga: disable over-current for Arria10 USB devkit
ARM: dts: Nokia N9: add support for up/down keys in the dts
ARM: dts: nomadik: add interrupt-parent for clcd
ARM: dts: Add ethernet to a bunch of platforms
ARM: dts: Add ethernet to the Gemini SoC
ARM: dts: rename oxnas dts files
ARM: dts: s5pv210: add interrupt-parent for ohci
ARM: lpc3250: fix uda1380 gpio numbers
ARM: dts: STi: Add gpio polarity for "hdmi,hpd-gpio" property
ARM: dts: dra7: Reduce shut down temperature of non-cpu thermal zones
ARM: dts: n900: Add aliases for lcd and tvout displays
ARM: dts: Update ti-sysc data for existing users
ARM: dts: Fix smartreflex compatible for omap3 shared mpu-iva instance
arm64: dts: marvell: armada-80x0: Fix pinctrl compatible string
arm: spear13xx: Fix spics gpio controller's warning
arm: spear13xx: Fix dmas cells
...
|
|
'clk-allwinner' into clk-next
* clk-aspeed:
clk: aspeed: Handle inverse polarity of USB port 1 clock gate
clk: aspeed: Fix return value check in aspeed_cc_init()
clk: aspeed: Add reset controller
clk: aspeed: Register gated clocks
clk: aspeed: Add platform driver and register PLLs
clk: aspeed: Register core clocks
clk: Add clock driver for ASPEED BMC SoCs
dt-bindings: clock: Add ASPEED constants
* clk-lock-UP:
clk: fix reentrancy of clk_enable() on UP systems
* clk-mediatek:
clk: mediatek: adjust dependency of reset.c to avoid unexpectedly being built
clk: mediatek: Fix all warnings for missing struct clk_onecell_data
clk: mediatek: fixup test-building of MediaTek clock drivers
clk: mediatek: group drivers under indpendent menu
* clk-allwinner:
clk: sunxi-ng: a83t: Add M divider to TCON1 clock
clk: sunxi-ng: fix the A64/H5 clock description of DE2 CCU
clk: sunxi-ng: add support for Allwinner H3 DE2 CCU
dt-bindings: fix the binding of Allwinner DE2 CCU of A83T and H3
clk: sunxi-ng: sun8i: a83t: Use sigma-delta modulation for audio PLL
clk: sunxi-ng: sun8i: a83t: Add /2 fixed post divider to audio PLL
clk: sunxi-ng: Support fixed post-dividers on NM style clocks
clk: sunxi-ng: sun50i: a64: Add 2x fixed post-divider to MMC module clocks
clk: sunxi-ng: Support fixed post-dividers on MP style clocks
clk: sunxi: Use PTR_ERR_OR_ZERO()
|
|
and 'clk-meson' into clk-next
* clk-remove-asm-clkdev:
clk: Move __clk_{get,put}() into private clk.h API
clk: sunxi: Use CLK_IS_CRITICAL flag for critical clks
arch: Remove clkdev.h asm-generic from Kbuild
clk: Prepare to remove asm-generic/clkdev.h
blackfin: Use generic clkdev.h header
* clk-debugfs-fixes:
clk: Simplify debugfs registration
clk: Fix debugfs_create_*() usage
clk: Show symbolic clock flags in debugfs
clk: Improve flags doc for of_clk_detect_critical()
* clk-renesas:
clk: renesas: r8a7796: Add FDP clock
clk: renesas: cpg-mssr: Keep wakeup sources active during system suspend
clk: renesas: mstp: Keep wakeup sources active during system suspend
clk: renesas: r8a77970: Add LVDS clock
* clk-meson:
clk: meson-axg: fix potential NULL dereference in axg_clkc_probe()
clk: meson-axg: make local symbol axg_gp0_params_table static
clk: meson-axg: fix return value check in axg_clkc_probe()
clk: meson: mpll: use 64-bit maths in params_from_rate
clk: meson-axg: add clock controller drivers
clk: meson-axg: add clocks dt-bindings required header
dt-bindings: clock: add compatible variant for the Meson-AXG
clk: meson: make the spinlock naming more specific
clk: meson: gxbb: remove IGNORE_UNUSED from mmc clocks
clk: meson: gxbb: fix wrong clock for SARADC/SANA
|
|
* clk-divider-container:
clk: divider: fix incorrect usage of container_of
Plus fixup sprd/div.c to pass the width too.
|
|
* clk-iproc:
clk: iproc: Minor tidy up of iproc pll data structures
clk: iproc: Allow plls to do minor rate changes without reset
clk: iproc: Fix error in the pll post divider rate calculation
clk: iproc: Allow iproc pll to runtime calculate vco parameters
* clk-mvebu:
clk: mvebu: armada-37xx-periph: Use PTR_ERR_OR_ZERO()
* clk-qcom-a53:
clk: qcom: Add APCS clock controller support
clk: qcom: Add regmap mux-div clocks support
clk: qcom: Add A53 PLL support
|
|
'clk-pxa' into clk-next
* clk-at91:
clk: at91: pmc: Support backup for programmable clocks
clk: at91: pmc: Save SCSR during suspend
clk: at91: pmc: Wait for clocks when resuming
* clk-imx7ulp:
clk: Don't touch hardware when reparenting during registration
* clk-axigen:
clk: axi-clkgen: Round closest in round_rate() and recalc_rate()
clk: axi-clkgen: Correctly handle nocount bit in recalc_rate()
* clk-si5351:
clk: si5351: _si5351_clkout_reset_pll() can be static
clk: si5351: Do not enable parent clocks on probe
clk: si5351: Rename internal plls to avoid name collisions
clk: si5351: Apply PLL soft reset before enabling the outputs
clk: si5351: Add DT property to enable PLL reset
clk: si5351: implement remove handler
* clk-pxa:
clk: pxa: unbreak lookup of CLK_POUT
|
|
and 'clk-qcom-ipq8074' into clk-next
* clk-spreadtrum:
clk: sprd: add clocks support for SC9860
clk: sprd: Add dt-bindings include file for SC9860
dt-bindings: Add Spreadtrum clock binding documentation
clk: sprd: add adjustable pll support
clk: sprd: add composite clock support
clk: sprd: add divider clock support
clk: sprd: add mux clock support
clk: sprd: add gate clock support
clk: sprd: Add common infrastructure
clk: move clock common macros out from vendor directories
* clk-mvebu-dvfs:
clk: mvebu: armada-37xx-periph: add DVFS support for cpu clocks
clk: mvebu: armada-37xx-periph: prepare cpu clk to be used with DVFS
clk: mvebu: armada-37xx-periph: cosmetic changes
* clk-qoriq:
clk: qoriq: add more divider clocks support
* clk-imx:
clk: imx51: uart4, uart5 gates only exist on imx50, imx53
* clk-qcom-ipq8074:
clk: qcom: ipq8074: add misc resets for PCIE and NSS
dt-bindings: clock: qcom: add misc resets for PCIE and NSS
clk: qcom: ipq8074: add GP and Crypto clocks
clk: qcom: ipq8074: add NSS ethernet port clocks
clk: qcom: ipq8074: add NSS clocks
clk: qcom: ipq8074: add PCIE, USB and SDCC clocks
clk: qcom: ipq8074: add remaining PLL’s
dt-bindings: clock: qcom: add remaining clocks for IPQ8074
clk: qcom: ipq8074: fix missing GPLL0 divider width
clk: qcom: add parent map for regmap mux
clk: qcom: add read-only divider operations
|
|
and 'clk-omap' into clk-next
* clk-qcom-alpha-pll:
clk: qcom: add read-only alpha pll post divider operations
clk: qcom: support for 2 bit PLL post divider
clk: qcom: support Brammo type Alpha PLL
clk: qcom: support Huayra type Alpha PLL
clk: qcom: support for dynamic updating the PLL
clk: qcom: support for alpha mode configuration
clk: qcom: flag for 64 bit CONFIG_CTL
clk: qcom: fix 16 bit alpha support calculation
clk: qcom: support for alpha pll properties
* clk-check-ops-ptr:
clk: check ops pointer on clock register
* clk-protect-rate:
clk: fix set_rate_range when current rate is out of range
clk: add clk_rate_exclusive api
clk: cosmetic changes to clk_summary debugfs entry
clk: add clock protection mechanism to clk core
clk: use round rate to bail out early in set_rate
clk: rework calls to round and determine rate callbacks
clk: add clk_core_set_phase_nolock function
clk: take the prepare lock out of clk_core_set_parent
clk: fix incorrect usage of ENOSYS
* clk-omap:
clk: ti: Drop legacy clk-3xxx-legacy code
|
|
The USB port 1 clock gate control has an inversed polarity
from all the other clock gates in the chip. This makes the
aspeed_clk_{enable,disable} functions honor the flag
CLK_GATE_SET_TO_DISABLE and set that flag appropriately
so it's set for all clocks except USB port 1.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
In case of error, the function of_iomap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: a2e230c7b2ea ("clk: Add clock driver for ASPEED BMC SoCs")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
There are some resets that are not associated with gates. These are
represented by a reset controller.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The majority of the clocks in the system are gates paired with a reset
controller that holds the IP in reset.
This borrows from clk_hw_register_gate, but registers two 'gates', one
to control the clock enable register and the other to control the reset
IP. This allows us to enforce the ordering:
1. Place IP in reset
2. Enable clock
3. Delay
4. Release reset
There are some gates that do not have an associated reset; these are
handled by using -1 as the index for the reset.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
This registers a platform driver to set up all of the non-core clocks.
The clocks that have configurable rates are now registered.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
This registers the core clocks; those which are required to calculate
the rate of the timer peripheral so the system can load a clocksource
driver.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
This adds the stub of a driver for the ASPEED SoCs. The clocks are
defined and the static registration is set up.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add support for the clocks provided by the CGU in the Ingenic JZ4770
SoC.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18482/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
This commit permits the PLLs to be dynamically enabled and disabled when
their children clocks are enabled and disabled.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18480/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
The second PLL of the JZ4770 does not have a bypass bit.
This commit makes it possible to support it with the current common CGU
code.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18479/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Previously, the clocks with a fixed divider would report their rate
as being the same as the one of their parent, independently of the
divider in use. This commit fixes this behaviour.
This went unnoticed as neither the jz4740 nor the jz4780 CGU code
have clocks with fixed dividers yet.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18477/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
The CGU common code does not modify the pointed clk_ops structure, so it
should be marked as const.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18476/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Changes from v1->v2:
Add 'select RESET_CONTROLLER' under COMMON_CLK_MEDIATEK and enable
reset.c to be built when COMMON_CLK_MEDIATEK is selected. That should
be quite reasonable because the reset controller is tightly embedded
inside and exported from these clock subsystems. At least it can be found
on infracfg and pericfg subsystem that both are really fundamental block
lots of devices must depend on.
commit 74cb0d6dde8 ("clk: mediatek: fixup test-building of MediaTek clock
drivers") can let the build system looking into the directory where the
clock drivers resides and then allow test-building the drivers.
But the change also gives rise to certain incorrect behavior which is
reset.c being built even not depending on either COMPILE_TEST or
ARCH_MEDIATEK alternative dependency. To get rid of reset.c being built
unexpectedly on the other platforms, it would be a good change that the
file should be built depending on its own specific configuration rather
than just on generic RESET_CONTROLLER one.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Reentrant calls to clk_enable() are not working on UP systems. This is
caused by the fact spin_trylock_irqsave() always returns true when
CONFIG_SMP=n (and CONFIG_DEBUG_SPINLOCK=n) which causes the reference
counting to not work correctly when clk_enable_lock() is called twice
before clk_enable_unlock() is called (this happens when clk_enable()
is called from within another clk_enable()).
This fixes the problem by skipping the call to spin_trylock_irqsave() on UP
systems and relying solely on reference counting. We also make sure to set
flags in this case so that we are not returning an uninitialized value.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
platform_get_resource() may return NULL, add proper
check to avoid potential NULL dereferencing.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
We don't need a goto here. Drop it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
When exposing data access through debugfs, the correct
debugfs_create_*() functions must be used, matching the data
types.
Remove all casts from data pointers passed to debugfs_create_*()
functions, as such casts prevent the compiler from flagging bugs.
clk_core.rate and .accuracy are "unsigned long", hence casting
their addresses to "u32 *" exposed the wrong halves on big-endian
64-bit systems. Fix this by using debugfs_create_ulong() instead.
Octal permissions are preferred, as they are easier to read than
symbolic permissions. Hence replace "S_IRUGO" by "0444"
throughout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[sboyd@codeaurora.org: Squash the octal change in too]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Currently the virtual "clk_flags" file in debugfs shows the numeric
value of the top-level framework flags for the specified clock.
Hence the user must manually interpret these values.
Moreover, on big-endian 64-bit systems, the wrong half of the value is
shown, due to the cast from "unsigned long *" to "u32 *".
Fix both issues by showing the symbolic flag names instead.
Any non-standard flags are shown as a hex number.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
This patch adds FDP1-0 clock to the R8A7796 SoC.
Signed-off-by: ABE Hiroshige <hiroshige.abe.zc@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: s/fdp0/fdp1-0/]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
We can move these APIs into the private header file now that we
don't have any users of the __clk_get() and __clk_put() APIs
outside of clkdev.c and clk.c.
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
We'd like to privatize __clk_get(), but the sunxi clk driver is
calling this function to keep a reference held on the clk and
call clk_prepare_enable() on it. We support this design in the
clk core now with the CLK_IS_CRITICAL flag, so let's just use
that instead.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
