| Age | Commit message (Collapse) | Author |
|---|
|
This silences a sparse warning about using a plain integer instead of
NULL for a pointer.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Current clock driver enables PLLA, cdev1 on Tegra20 and extern1 on
Tegra30 and above as a part of clocks init and there is no need to
have these audio clocks enabled by the clock driver.
extern1 is used as parent for clk_out_1 and clk_out_1 is dedicated
for audio mclk on Tegra30 and above Tegra platforms and these clocks
are taken care by ASoC driver.
So, this patch removes audio related clocks configuration from clock
init of Tegra20 and above.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Current Tegra clock driver registers PMC clocks clk_out_1, clk_out_2,
clk_out_3 and 32KHz blink output in tegra_pmc_init() which does direct
PMC register access during clk_ops and these PMC register read and write
access will not happen when PMC is in secure mode.
Any direct PMC register access from non-secure world will not go
through.
All the PMC clocks are moved to Tegra PMC driver with PMC as a clock
provider.
This patch removes tegra_pmc_clk_init along with corresponding clk ids
from Tegra clock driver.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra has no CLK_M_DIV2 and CLK_M_DIV4 clocks and instead it has
OSC_DIV2 and OSC_DIV4 clocks from OSC pads which are the possible
parents of PMC clocks for Tegra30 through Tegra210.
Tegra PMC clock parents are changed to use OSC_DIV clocks.
So, this patch removes CLK_M_DIV fixed clocks
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra PMC clocks clk_out_1, clk_out_2, and clk_out_3 supported parents
are osc, osc_div2, osc_div4 and extern clock.
Clock driver is using incorrect parents clk_m, clk_m_div2, clk_m_div4
for PMC clocks.
This patch fixes this.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
OSC is one of the parent for Tegra PMC clocks clk_out_1, clk_out_2,
and clk_out_3.
This patch adds Tegra OSC to clock lookup.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra30 through Tegra210 has OSC_DIV2 and OSC_DIV4 fixed clocks
from the OSC pads.
This patch adds support for these clocks.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
'clk-freescale' and 'clk-qoriq' into clk-next
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Fixes for clk controllers on qcom msm8998 SoCs
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Adjust composite clk to new way of describing clk parents
- Add a driver for BCLK of Freescale SAI cores
* clk-imx: (32 commits)
clk: imx: Add support for i.MX8MP clock driver
dt-bindings: imx: Add clock binding doc for i.MX8MP
clk: imx: gate4: Switch imx_clk_gate4_flags() to clk_hw based API
clk: imx: imx8mq: Switch to clk_hw based API
clk: imx: imx8mm: Switch to clk_hw based API
clk: imx: imx8mn: Switch to clk_hw based API
clk: imx: Remove __init for imx_obtain_fixed_clk_hw() API
clk: imx: gate3: Switch to clk_hw based API
clk: imx: add hw API imx_clk_hw_mux2_flags
clk: imx: add imx_unregister_hw_clocks
clk: imx: clk-composite-8m: Switch to clk_hw based API
clk: imx: clk-pll14xx: Switch to clk_hw based API
clk: imx7up: Rename the clks to hws
clk: imx: Rename the imx_clk_divider_gate to imply it's clk_hw based
clk: imx: Rename the imx_clk_pfdv2 to imply it's clk_hw based
clk: imx: Rename the imx_clk_pllv4 to imply it's clk_hw based
clk: imx: Rename sccg and frac pll register to suggest clk_hw
clk: imx: imx7ulp composite: Rename to show is clk_hw based
clk: imx: pllv2: Switch to clk_hw based API
clk: imx: pllv1: Switch to clk_hw based API
...
* clk-ti:
clk: ti: clkctrl: Fix hidden dependency to node name
clk: ti: add clkctrl data dra7 sgx
clk: ti: omap5: Add missing AESS clock
clk: ti: dra7: fix parent for gmac_clkctrl
clk: ti: dra7: add vpe clkctrl data
clk: ti: dra7: add cam clkctrl data
dt-bindings: clock: Move ti-dra7-atl.h to dt-bindings/clock
* clk-xilinx:
clk: zynqmp: Add support for clock with CLK_DIVIDER_POWER_OF_TWO flag
clk: zynqmp: Fix divider calculation
clk: zynqmp: Add support for get max divider
clk: zynqmp: Warn user if clock user are more than allowed
clk: zynqmp: Extend driver for versal
dt-bindings: clock: Add bindings for versal clock driver
* clk-nvidia:
clk: tegra20/30: Explicitly set parent clock for Video Decoder
clk: tegra20/30: Don't pre-initialize displays parent clock
clk: tegra: divider: Check UART's divider enable-bit state on rate's recalculation
clk: tegra: clk-dfll: Remove call to pm_runtime_irq_safe()
clk: tegra: Mark fuse clock as critical
* clk-qcom: (35 commits)
clk: qcom: rpmh: Sort OF match table
dt-bindings: fix warnings in validation of qcom,gcc.yaml
dt-binding: fix compilation error of the example in qcom,gcc.yaml
clk: qcom: Add ipq6018 Global Clock Controller support
clk: qcom: Add DT bindings for ipq6018 gcc clock controller
clk: qcom: gcc-msm8996: Fix parent for CLKREF clocks
clk: qcom: rpmh: Add IPA clock for SC7180
clk: qcom: rpmh: skip undefined clocks when registering
clk: qcom: Add video clock controller driver for SC7180
dt-bindings: clock: Introduce SC7180 QCOM Video clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM VIDEOCC clock bindings
clk: qcom: Add graphics clock controller driver for SC7180
dt-bindings: clock: Introduce SC7180 QCOM Graphics clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM GPUCC clock bindings
clk: qcom: apcs-msm8916: use clk_parent_data to specify the parent
clk: qcom: Add display clock controller driver for SC7180
dt-bindings: clock: Introduce QCOM sc7180 display clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM DISPCC clock bindings
clk: qcom: clk-alpha-pll: Add support for Fabia PLL calibration
clk: qcom: alpha-pll: Remove useless read from set rate
...
* clk-freescale:
clk: fsl-sai: new driver
dt-bindings: clock: document the fsl-sai driver
clk: composite: add _register_composite_pdata() variants
* clk-qoriq:
clk: qoriq: add ls1088a hwaccel clocks support
clk: ls1028a: Add clock driver for Display output interface
dt/bindings: clk: Add YAML schemas for LS1028A Display Clock bindings
|
|
The VDE parent won't be changed automatically to PLLC if bootloader
didn't do that for us, hence let's explicitly set the parent for
consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Both Tegra20 and Tegra30 are initializing display's parent clock
incorrectly because PLLP is running at 216/408MHz while display rate is
set to 600MHz, but pre-setting the parent isn't needed at all because
display driver selects proper parent anyways.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
recalculation
UART clock is divided using divisor values from DLM/DLL registers when
enable-bit is unset in clk register and clk's divider configuration isn't
taken onto account in this case. This doesn't cause any problems, but
let's add a check for the divider's enable-bit state, for consistency.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
pm_runtime_irq_safe() is not needed as interrupts are allowed during
suspend and resume. This was added mistakenly during DFLL suspend and
resume support patch.
While at it, also update the description of the dev argument that is
passed to the tegra_dfll_suspend() function.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
For a little over a year, U-Boot on Tegra124 has configured the flow
controller to perform automatic RAM re-repair on off->on power
transitions of the CPU rail[1]. This is mandatory for correct operation
of Tegra124. However, RAM re-repair relies on certain clocks, which the
kernel must enable and leave running. The fuse clock is one of those
clocks. Mark this clock as critical so that LP1 power mode (system
suspend) operates correctly.
[1] 3cc7942a4ae5 ARM: tegra: implement RAM repair
Reported-by: Jonathan Hunter <jonathanh@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
It's unlikely to happen in practice ever, but makes static checkers happy.
Fixes: 535f296d47de ("clk: tegra: Add suspend and resume support on Tegra210")
Reported-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lkml.kernel.org/r/20191210020512.6088-1-digetx@gmail.com
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
match_string() returns the array index of a matching string.
Use it instead of the open-coded implementation.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lkml.kernel.org/r/20191109034226.21044-1-yuehaibing@huawei.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
If CONFIG_PM_SLEEP is n, build fails:
drivers/clk/tegra/clk-tegra210.c:3426:13: error:
tegra210_clk_suspend undeclared here (not in a function); did you mean tegra_clk_ndspeed?
.suspend = tegra210_clk_suspend,
^~~~~~~~~~~~~~~~~~~~
tegra_clk_ndspeed
drivers/clk/tegra/clk-tegra210.c:3427:12: error:
tegra210_clk_resume undeclared here (not in a function); did you mean tegra210_clk_suspend?
.resume = tegra210_clk_resume,
Use ifdef to guard this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 27d10d548c04 ("clk: tegra: Add suspend and resume support on Tegra210")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
There is no need to re-configure PLLX if its configuration in unchanged
on return from suspend / cpuidle, this saves 300us if PLLX is already
enabled (common case for cpuidle).
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
All the CAR controller settings are lost on suspend when core power goes
off. This implement saving and restoring context for all PLLs and clocks
during system suspend and resume to have the clocks back to same state
for normal operation.
Clock driver suspend and resume are registered as syscore_ops as clocks
restore need to happen before the other drivers resume to have all their
clocks back to the same state as before suspend.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Move CLK_OUT_ENB and RST_DEVICES registers to clk.h to share these with
Tegra clock driver.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This patch uses fence_udelay rather than udelay during PLLU
initialization to ensure writes to clock registers happens before
waiting for specified delay.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This patch implements DFLL suspend and resume operation.
During system suspend entry, CPU clock will switch CPU to safe
clock source of PLLP and disables DFLL clock output.
DFLL driver suspend confirms DFLL disable state and errors out on
being active.
DFLL is re-initialized during the DFLL driver resume as it goes
through complete reset during suspend entry.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This patch implements restore_context for clk_super_mux and clk_super.
During system supend, core power goes off the and context of Tegra
CAR registers is lost.
So on system resume, context of super clock registers are restored
to have them in same state as before suspend.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This patch has a fix to enable PLLP branches to CPU before changing
the CPU cluster clock source to PLLP for Gen5 Super clock and
disables PLLP branches to CPU when not in use.
During system suspend entry and exit, CPU source will be switched
to PLLP and this needs PLLP branches to be enabled to CPU prior to
the switch.
On system resume, warmboot code enables PLLP branches to CPU and
powers up the CPU with PLLP clock source.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This patch implements restore_context support for clk-periph and
clk-sdmmc-mux clock operations to restore clock parent and rates
on system resume.
During system suspend, core power goes off and looses the context
of the Tegra clock controller registers.
So on system resume, clocks parent and rate are restored back to
the context before suspend based on cached data.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This patch adds support for saving OSC clock frequency and the
drive-strength during OSC clock init and creates an API to restore
OSC control register value from the saved context.
This API is invoked by Tegra210 clock driver during system resume
to restore the OSC clock settings.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This patch implements save and restore of PLL context.
During system suspend, core power goes off and looses the settings
of the Tegra CAR controller registers.
So during resume, pll context is restored based on cached rate
and state.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This patch implements save and restore of pllout context.
During system suspend, core power goes off and looses the settings
of the Tegra CAR controller registers.
So during suspend entry the state of pllout is saved and on resume
it is restored back to have pllout in same state as before suspend.
pllout rate is saved and restore in clock divider so it will be at
same rate as before suspend when pllout state is restored.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This patch implements context restore for clock divider.
During system suspend, core power goes off and looses the settings
of the Tegra CAR controller registers.
So on resume, clock dividers are restored back for normal operation.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
In order to allow the display driver to deal uniformly with all SOR
generations, implement the SOR clocks in a way that is compatible with
Tegra186 and later.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
In order to allow the display driver to deal uniformly with all SOR
generations, implement the SOR clocks in a way that is compatible with
Tegra186 and later.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This makes Tegra124 and Tegra210 consistent with subsequent Tegra
generations.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The SOR0 clock on Tegra210 is very different from the SOR0 clock found
on Tegra124. Move the Tegra124 implementation to the Tegra124 driver so
that a custom implementation can be provided on Tegra210 without
clashing with the existing clock.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Later SoC generations implement this clock as SOR1_OUT. For consistency,
the Tegra210 implementation was adapted to match the same name in commit
4d1dc4018573 ("dt-bindings: clock: tegra: Add sor1_out clock").
Clean up the remaining pieces by adopting the new name for the internal
identifiers and remove the old alias. Note that since both SOR1_SRC and
SOR1_OUT were referring to the same device tree clock ID, this does not
break device tree ABI.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
A proper External Memory Controller clock rounding and parent selection
functionality is required by the EMC drivers, it is not available using
the generic clock implementation because only the Memory Controller driver
is aware of what clock rates are actually available for a particular
device. EMC drivers will have to register a Tegra-specific CLK-API
callback which will perform rounding of a requested rate. EMC clock users
won't be able to request EMC clock by getting -EPROBE_DEFER until EMC
driver is probed and the callback is set up.
The functionality is somewhat similar to the clk-emc.c which serves
Tegra124+ SoCs. The later HW generations support more parent clock sources
and the HW configuration / integration with the EMC drivers differs a tad
from the older gens, hence it's not really worth to try to squash
everything into a single source file.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round of clk driver and framework updates is heavy on the driver
update side. The two main highlights in the core framework are the
addition of an bulk clk_get API that handles optional clks and an
extra debugfs file that tells the developer about the current parent
of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is
mostly because that SoC has started converting to the clk_hw style of
clk registration. The next big update is in the Amlogic meson clk
driver that gained some support for audio, cpu, and temperature clks
while fixing some PLL issues. Finally, the biggest thing that stands
out is the conversion of a large part of the Allwinner sunxi-ng driver
to the new clk parent scheme that uses less strings and more pointer
comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks
here and there to clk data along with the normal addition of a handful
of new drivers and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (190 commits)
clk: consoldiate the __clk_get_hw() declarations
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: lochnagar: Update DT binding doc to include the primary SPDIF MCLK
clk: Add Si5341/Si5340 driver
dt-bindings: clock: Add silabs,si5341
clk: clk-si544: Implement small frequency change support
clk: add BCM63XX gated clock controller driver
devicetree: document the BCM63XX gated clock bindings
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: rockchip: export HDMIPHY clock on rk3228
clk: rockchip: add watchdog pclk on rk3328
clk: rockchip: add clock id for hdmi_phy special clock on rk3228
clk: rockchip: add clock id for watchdog pclk on rk3328
clk: at91: sckc: add support for SAM9X60
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A handful of clk driver fixes and one core framework fix
- Do a DT/firmware lookup in clk_core_get() even when the DT index is
a nonsensical value
- Fix some clk data typos in the Amlogic DT headers/code
- Avoid returning junk in the TI clk driver when an invalid clk is
looked for
- Fix dividers for the emac clks on Stratix10 SoCs
- Fix default HDA rates on Tegra210 to correct distorted audio"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: socfpga: stratix10: fix divider entry for the emac clocks
clk: Do a DT parent lookup even when index < 0
clk: tegra210: Fix default rates for HDA clocks
clk: ti: clkctrl: Fix returning uninitialized data
clk: meson: meson8b: fix a typo in the VPU parent names array variable
clk: meson: fix MPLL 50M binding id typo
|
|
It turns out that this PLL is not used on Tegra210, so there's no need
to enable it via the init table. Remove the init table entry for this
PLL to avoid it getting enabled at boot time. If the bootloader enabled
it and forgot to turn it off, the common clock framework will now know
to disable it because it is unused.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
A PLL in IDDQ doesn't work, whether it's enabled or not. This is not a
configuration that makes sense, so warn about it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
There is no need to warn if the reference PLL is enabled with the
correct defaults. Only warn if the boot values don't match the defaults.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Full-speed and low-speed USB devices do not work with Tegra210
platforms because of incorrect PLLU/PLLU_OUT1 clock settings.
When full-speed device is connected:
[ 14.059886] usb 1-3: new full-speed USB device number 2 using tegra-xusb
[ 14.196295] usb 1-3: device descriptor read/64, error -71
[ 14.436311] usb 1-3: device descriptor read/64, error -71
[ 14.675749] usb 1-3: new full-speed USB device number 3 using tegra-xusb
[ 14.812335] usb 1-3: device descriptor read/64, error -71
[ 15.052316] usb 1-3: device descriptor read/64, error -71
[ 15.164799] usb usb1-port3: attempt power cycle
When low-speed device is connected:
[ 37.610949] usb usb1-port3: Cannot enable. Maybe the USB cable is bad?
[ 38.557376] usb usb1-port3: Cannot enable. Maybe the USB cable is bad?
[ 38.564977] usb usb1-port3: attempt power cycle
This commit fixes the issue by:
1. initializing PLLU_OUT1 before initializing XUSB_FS_SRC clock
because PLLU_OUT1 is parent of XUSB_FS_SRC.
2. changing PLLU post-divider to /2 (DIVP=1) according to Technical
Reference Manual.
Fixes: e745f992cf4b ("clk: tegra: Rework pll_u")
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently the default clock rates for the HDA and HDA2CODEC_2X clocks
are both 19.2MHz. However, the default rates for these clocks should
actually be 51MHz and 48MHz, respectively. The current clock settings
results in a distorted output during audio playback. Correct the default
clock rates for these clocks by specifying them in the clock init table
for Tegra210.
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that we've gotten rid of clk_readl() we can remove io.h from the
clk-provider header and push out the io.h include to any code that isn't
already including the io.h header but using things like readl/writel,
etc.
Found with this grep:
git grep -l clk-provider.h | grep '.c$' | xargs git grep -L 'linux/io.h' | \
xargs git grep -l \
-e '\<__iowrite32_copy\>' --or \
-e '\<__ioread32_copy\>' --or \
-e '\<__iowrite64_copy\>' --or \
-e '\<ioremap_page_range\>' --or \
-e '\<ioremap_huge_init\>' --or \
-e '\<arch_ioremap_pud_supported\>' --or \
-e '\<arch_ioremap_pmd_supported\>' --or \
-e '\<devm_ioport_map\>' --or \
-e '\<devm_ioport_unmap\>' --or \
-e '\<IOMEM_ERR_PTR\>' --or \
-e '\<devm_ioremap\>' --or \
-e '\<devm_ioremap_nocache\>' --or \
-e '\<devm_ioremap_wc\>' --or \
-e '\<devm_iounmap\>' --or \
-e '\<devm_ioremap_release\>' --or \
-e '\<devm_memremap\>' --or \
-e '\<devm_memunmap\>' --or \
-e '\<__devm_memremap_pages\>' --or \
-e '\<pci_remap_cfgspace\>' --or \
-e '\<arch_has_dev_port\>' --or \
-e '\<arch_phys_wc_add\>' --or \
-e '\<arch_phys_wc_del\>' --or \
-e '\<memremap\>' --or \
-e '\<memunmap\>' --or \
-e '\<arch_io_reserve_memtype_wc\>' --or \
-e '\<arch_io_free_memtype_wc\>' --or \
-e '\<__io_aw\>' --or \
-e '\<__io_pbw\>' --or \
-e '\<__io_paw\>' --or \
-e '\<__io_pbr\>' --or \
-e '\<__io_par\>' --or \
-e '\<__raw_readb\>' --or \
-e '\<__raw_readw\>' --or \
-e '\<__raw_readl\>' --or \
-e '\<__raw_readq\>' --or \
-e '\<__raw_writeb\>' --or \
-e '\<__raw_writew\>' --or \
-e '\<__raw_writel\>' --or \
-e '\<__raw_writeq\>' --or \
-e '\<readb\>' --or \
-e '\<readw\>' --or \
-e '\<readl\>' --or \
-e '\<readq\>' --or \
-e '\<writeb\>' --or \
-e '\<writew\>' --or \
-e '\<writel\>' --or \
-e '\<writeq\>' --or \
-e '\<readb_relaxed\>' --or \
-e '\<readw_relaxed\>' --or \
-e '\<readl_relaxed\>' --or \
-e '\<readq_relaxed\>' --or \
-e '\<writeb_relaxed\>' --or \
-e '\<writew_relaxed\>' --or \
-e '\<writel_relaxed\>' --or \
-e '\<writeq_relaxed\>' --or \
-e '\<readsb\>' --or \
-e '\<readsw\>' --or \
-e '\<readsl\>' --or \
-e '\<readsq\>' --or \
-e '\<writesb\>' --or \
-e '\<writesw\>' --or \
-e '\<writesl\>' --or \
-e '\<writesq\>' --or \
-e '\<inb\>' --or \
-e '\<inw\>' --or \
-e '\<inl\>' --or \
-e '\<outb\>' --or \
-e '\<outw\>' --or \
-e '\<outl\>' --or \
-e '\<inb_p\>' --or \
-e '\<inw_p\>' --or \
-e '\<inl_p\>' --or \
-e '\<outb_p\>' --or \
-e '\<outw_p\>' --or \
-e '\<outl_p\>' --or \
-e '\<insb\>' --or \
-e '\<insw\>' --or \
-e '\<insl\>' --or \
-e '\<outsb\>' --or \
-e '\<outsw\>' --or \
-e '\<outsl\>' --or \
-e '\<insb_p\>' --or \
-e '\<insw_p\>' --or \
-e '\<insl_p\>' --or \
-e '\<outsb_p\>' --or \
-e '\<outsw_p\>' --or \
-e '\<outsl_p\>' --or \
-e '\<ioread8\>' --or \
-e '\<ioread16\>' --or \
-e '\<ioread32\>' --or \
-e '\<ioread64\>' --or \
-e '\<iowrite8\>' --or \
-e '\<iowrite16\>' --or \
-e '\<iowrite32\>' --or \
-e '\<iowrite64\>' --or \
-e '\<ioread16be\>' --or \
-e '\<ioread32be\>' --or \
-e '\<ioread64be\>' --or \
-e '\<iowrite16be\>' --or \
-e '\<iowrite32be\>' --or \
-e '\<iowrite64be\>' --or \
-e '\<ioread8_rep\>' --or \
-e '\<ioread16_rep\>' --or \
-e '\<ioread32_rep\>' --or \
-e '\<ioread64_rep\>' --or \
-e '\<iowrite8_rep\>' --or \
-e '\<iowrite16_rep\>' --or \
-e '\<iowrite32_rep\>' --or \
-e '\<iowrite64_rep\>' --or \
-e '\<__io_virt\>' --or \
-e '\<pci_iounmap\>' --or \
-e '\<virt_to_phys\>' --or \
-e '\<phys_to_virt\>' --or \
-e '\<ioremap_uc\>' --or \
-e '\<ioremap\>' --or \
-e '\<__ioremap\>' --or \
-e '\<iounmap\>' --or \
-e '\<ioremap\>' --or \
-e '\<ioremap_nocache\>' --or \
-e '\<ioremap_uc\>' --or \
-e '\<ioremap_wc\>' --or \
-e '\<ioremap_wc\>' --or \
-e '\<ioremap_wt\>' --or \
-e '\<ioport_map\>' --or \
-e '\<ioport_unmap\>' --or \
-e '\<ioport_map\>' --or \
-e '\<ioport_unmap\>' --or \
-e '\<xlate_dev_kmem_ptr\>' --or \
-e '\<xlate_dev_mem_ptr\>' --or \
-e '\<unxlate_dev_mem_ptr\>' --or \
-e '\<virt_to_bus\>' --or \
-e '\<bus_to_virt\>' --or \
-e '\<memset_io\>' --or \
-e '\<memcpy_fromio\>' --or \
-e '\<memcpy_toio\>'
I also reordered a couple includes when they weren't alphabetical and
removed clk.h from kona, replacing it with clk-provider.h because
that driver doesn't use clk consumer APIs.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: John Crispin <john@phrozen.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
and 'clk-spdx' into clk-next
- Support for STM32F769
- Rework AT91 sckc DT bindings
- Fix slow RC oscillator issue on sama5d3
- AT91 sam9x60 PMC support
- SiFive FU540 PRCI and PLL support
* clk-stm32f4:
clk: stm32mp1: Add ddrperfm clock
clk: stm32: Introduce clocks of STM32F769 board
* clk-tegra:
clk: tegra: divider: Mark Memory Controller clock as read-only
clk: tegra: emc: Replace BUG() with WARN_ONCE()
clk: tegra: emc: Fix EMC max-rate clamping
clk: tegra: emc: Support multiple RAM codes
clk: tegra: emc: Don't enable EMC clock manually
clk: tegra124: Remove lock-enable bit from PLLM
clk: tegra: Fix PLLM programming on Tegra124+ when PMC overrides divider
clk: tegra: Don't enable already enabled PLLs
* clk-at91:
clk: at91: Mark struct clk_range as const
clk: at91: add sam9x60 pmc driver
dt-bindings: clk: at91: add bindings for SAM9X60 pmc
clk: at91: add sam9x60 PLL driver
clk: at91: master: Add sam9x60 support
clk: at91: usb: Add sam9x60 support
clk: at91: allow configuring generated PCR layout
clk: at91: allow configuring peripheral PCR layout
clk: at91: sckc: handle different RC startup time
clk: at91: modernize sckc binding
dt-bindings: clock: at91: new sckc bindings
* clk-sifive-fu540:
clk: sifive: add a driver for the SiFive FU540 PRCI IP block
clk: analogbits: add Wide-Range PLL library
dt-bindings: clk: add documentation for the SiFive PRCI driver
* clk-spdx:
clk: sunxi-ng: Use the correct style for SPDX License Identifier
clk: sprd: Use the correct style for SPDX License Identifier
clk: renesas: Use the correct style for SPDX License Identifier
clk: qcom: Use the correct style for SPDX License Identifier
clk: davinci: Use the correct style for SPDX License Identifier
clk: actions: Use the correct style for SPDX License Identifier
|
|
'clk-zynq' into clk-next
- Various static analysis fixes/finds
- Video Engine (ECLK) support on Aspeed SoCs
- Xilinx ZynqMP Versal platform support
- Convert Xilinx ZynqMP driver to be struct oriented
* clk-sa:
clk: mvebu: fix spelling mistake "gatable" -> "gateable"
clk: ux500: add range to usleep_range
clk: tegra: Make tegra_clk_super_mux_ops static
clk: davinci: cfgchip: use PTR_ERR_OR_ZERO in da8xx_cfgchip_register_div4p5
* clk-aspeed:
clk: Aspeed: Setup video engine clocking
* clk-samsung:
clk: samsung: exynos5410: Add gate clock for ADC
clk: samsung: dt-bindings: Add ADC clock ID to Exynos5410
clk: samsung: dt-bindings: Put CLK_UART3 in order
* clk-ingenic:
clk: ingenic: jz4725b: Add UDC PHY clock
dt-bindings: clock: jz4725b-cgu: Add UDC PHY clock
* clk-zynq:
clk: zynqmp: use structs for clk query responses
clk: zynqmp: fix check for fractional clock
clk: zynqmp: do not export zynqmp_clk_register_* functions
clk: zynqmp: fix kerneldoc of __zynqmp_clock_get_parents
drivers: clk: Update clock driver to handle clock attribute
drivers: clk: zynqmp: Allow zero divisor value
|
|
The Memory Controller (MC) clock rate can't be simply changed and nothing
in kernel need to change the rate, hence let's make the clock read-only.
This id also needed for the EMC driver because timing configuration may
require the MC clock diver to be disabled, that is handled by the EMC
clock / EMC driver integration and CLK framework shall not touch the
MC divider configuration on the EMC clock rate change.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
