| Age | Commit message (Collapse) | Author |
|---|
|
clk_notifier_register() documentation states, that the provided notifier
callbacks associated with the notifier must not re-enter into the clk
framework by calling any top-level clk APIs. Fix this by replacing
clk_get_rate() calls with clk_hw_get_rate(), which is safe in this
context.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
Ensure that clocks for core SoC modules (including TZPC0..9 modules)
are enabled for suspend/resume cycle. This fixes suspend/resume
support on Exynos5422-based Odroid XU3/XU4 boards.
Suggested-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
The bit of GATE_BUS_PERIS1 for CLK_SECKEY is just reserved on
exynos5422/5800, not exynos5420. Define gate clk for exynos5420 to
handle the bit only on exynos5420.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
[m.szyprow: rewrote commit subject]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
All sclk_uart clocks in TOP CMU have to be kept enabled for suspend/resume
cycle, otherwise TM2(e) boards hangs before entering the suspend mode.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
Exynos4412 ISP clock are provided by separate Exynos4412 ISP clock
driver, so support for them in Exynos4-clk driver can be removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
Before entering system suspend, one has to ensure that some clocks from
TOP, CPIF and PERIC CMUs are enabled. This is needed by the firmware
to properly perform system suspend operation. Instead of adding more and
more clocks with CRITICAL flag, simply enable those clocks directly in
respective CMU registers using 'suspend_regs' feature.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
SoC clock drivers should suspend after every other drivers in the system,
which are using clocks and resume before them. The last stage for calling
suspend device callbacks is NOIRQ stage and there exists driver, which use
that state (dwmmc-exynos), so Exynos5433 clocks driver should also use it.
During the same stage, clocks driver will be always suspended after its
clients as a direct result of proper device probe order (deferred probe
reorders the suspend call sequence).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
Replace common suspend/resume handling code by generic helper.
Almost no functional change, the only difference is in handling
of hypothetical memory allocation failure on boot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
Replace common suspend/resume handling code by generic helper.
Handling of PLLs is a bit different in generic code, as they are handled
in the same way as other clock registers. Such approach was already used
on later Exynos SoCs and worked fine. Tests have shown that it works also
on Exynos4 SoCs and significantly simplifies the code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
Some registers of clock controller have to be set to certain values before
entering system suspend state. Till now drivers did that on their own,
but it will be easier to handle it by generic code and let drivers simply
to provide the list of registers and their state.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
Replace common suspend/resume handling code by generic helper.
Almost no functional change, the only difference is in handling
of hypothetical memory allocation failure on boot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
Replace common suspend/resume handling code by generic helper.
Almost no functional change, the only difference is in handling
of hypothetical memory allocation failure on boot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
Replace common suspend/resume handling code by generic helper.
Almost no functional change, the only difference is in handling
of hypothetical memory allocation failure on boot.
[snawrocki@kernel.org: Whitespace correction]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
Replace common suspend/resume handling code by generic helper.
Almost no functional change, the only difference is in handling
of hypothetical memory allocation failure on boot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
Replace common suspend/resume handling code by generic helper.
Almost no functional change, the only difference is in handling
of hypothetical memory allocation failure on boot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
Replace common suspend/resume handling code by generic helper.
Almost no functional change, the only difference is in handling
of hypothetical memory allocation failure on boot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
Exynos Audio SubSystem and Exynos3250 clock drivers don't use any syscore
function, so don't include linux/syscore_ops.h in their code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (52 commits)
drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests
soc: fsl: cleanup Kconfig menu
soc: fsl: dpio: Convert DPIO documentation to .rst
staging: fsl-mc: Remove remaining files
staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl
staging: fsl-dpaa2: eth: move generic FD defines to DPIO
soc: fsl: qe: gpio: Add qe_gpio_set_multiple
usb: host: exynos: Remove support for Exynos5440
clk: samsung: Remove support for Exynos5440
soc: sunxi: Add the A13, A23 and H3 system control compatibles
reset: uniphier: add reset control support for SPI
cpufreq: exynos: Remove support for Exynos5440
ata: ahci-platform: Remove support for Exynos5440
soc: imx6qp: Use GENPD_FLAG_ALWAYS_ON for PU errata
soc: mediatek: pwrap: add mt6351 driver for mt6797 SoCs
soc: mediatek: pwrap: add pwrap driver for mt6797 SoCs
soc: mediatek: pwrap: fix cipher init setting error
dt-bindings: pwrap: mediatek: add pwrap support for MT6797
reset: uniphier: add USB3 core reset control
dt-bindings: reset: uniphier: add USB3 core reset support
...
|
|
Remove unused 'mout_user_aclk400_mcuisp_p4x12' variable to fix GCC warning:
drivers/clk/samsung/clk-exynos4412-isp.c:40:27: warning:
'mout_user_aclk400_mcuisp_p4x12' defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The Exynos5440 is not actively developed, there are no development
boards available and probably there are no real products with it.
Remove wide-tree support for Exynos5440.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Sylwester Nawrocki <snawrocki@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time we have a good set of changes to the core framework that do
some general cleanups, but nothing too major. The majority of the diff
goes to two SoCs, Actions Semi and Qualcomm. A brand new driver is
introduced for Actions Semi so it takes up some lines to add all the
different types, and the Qualcomm diff is there because we add support
for two SoCs and it's quite a bit of data.
Otherwise the big driver updates are on TI Davinci and Amlogic
platforms. And then the long tail of driver updates for various fixes
and stuff follows after that.
Core:
- debugfs cleanups removing error checking and an unused provider API
- Removal of a clk init typedef that isn't used
- Usage of match_string() to simplify parent string name matching
- OF clk helpers moved to their own file (linux/of_clk.h)
- Make clk warnings more readable across kernel versions
New Drivers:
- Qualcomm SDM845 GCC and Video clk controllers
- Qualcomm MSM8998 GCC
- Actions Semi S900 SoC support
- Nuvoton npcm750 microcontroller clks
- Amlogic axg AO clock controller
Removed Drivers:
- Deprecated Rockchip clk-gate driver
Updates:
- debugfs functions stopped checking return values
- Support for the MSIOF module clocks on Rensas R-Car M3-N
- Support for the new Rensas RZ/G1C and R-Car E3 SoCs
- Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs
- Berlin and Amlogic SPDX tagging
- Usage of of_clk_get_parent_count() in more places
- Proper implementation of the CDEV1/2 clocks on Tegra20
- Allwinner H6 PRCM clock support and R40 EMAC support
- Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet
- Round closest support for meson's mpll driver
- Support for meson8b nand clocks and gxbb video decoder clocks
- Mediatek mali clks
- STM32MP1 fixes
- Uniphier LD11/LD20 stream demux system clock"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits)
clk: qcom: Export clk_fabia_pll_configure()
clk: bcm: Update and add Stingray clock entries
dt-bindings: clk: Update Stingray binding doc
clk-si544: Properly round requested frequency to nearest match
clk: ingenic: jz4770: Add 150us delay after enabling VPU clock
clk: ingenic: jz4770: Enable power of AHB1 bus after ungating VPU clock
clk: ingenic: jz4770: Modify C1CLK clock to disable CPU clock stop on idle
clk: ingenic: jz4770: Change OTG from custom to standard gated clock
clk: ingenic: Support specifying "wait for clock stable" delay
clk: ingenic: Add support for clocks whose gate bit is inverted
clk: use match_string() helper
clk: bcm2835: use match_string() helper
clk: Return void from debug_init op
clk: remove clk_debugfs_add_file()
clk: tegra: no need to check return value of debugfs_create functions
clk: davinci: no need to check return value of debugfs_create functions
clk: bcm2835: no need to check return value of debugfs_create functions
clk: no need to check return value of debugfs_create functions
clk: imx6: add EPIT clock support
clk: mvebu: use correct bit for 98DX3236 NAND
...
|
|
Replaces open-coded struct size calculations with struct_size() for
devm_*, f2fs_*, and sock_* allocations. Automatically generated (and
manually adjusted) from the following Coccinelle script:
// Direct reference to struct field.
@@
identifier alloc =~ "devm_kmalloc|devm_kzalloc|sock_kmalloc|f2fs_kmalloc|f2fs_kzalloc";
expression HANDLE;
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(HANDLE, sizeof(*VAR) + COUNT * sizeof(*VAR->ELEMENT), GFP)
+ alloc(HANDLE, struct_size(VAR, ELEMENT, COUNT), GFP)
// mr = kzalloc(sizeof(*mr) + m * sizeof(mr->map[0]), GFP_KERNEL);
@@
identifier alloc =~ "devm_kmalloc|devm_kzalloc|sock_kmalloc|f2fs_kmalloc|f2fs_kzalloc";
expression HANDLE;
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(HANDLE, sizeof(*VAR) + COUNT * sizeof(VAR->ELEMENT[0]), GFP)
+ alloc(HANDLE, struct_size(VAR, ELEMENT, COUNT), GFP)
// Same pattern, but can't trivially locate the trailing element name,
// or variable name.
@@
identifier alloc =~ "devm_kmalloc|devm_kzalloc|sock_kmalloc|f2fs_kmalloc|f2fs_kzalloc";
expression HANDLE;
expression GFP;
expression SOMETHING, COUNT, ELEMENT;
@@
- alloc(HANDLE, sizeof(SOMETHING) + COUNT * sizeof(ELEMENT), GFP)
+ alloc(HANDLE, CHECKME_struct_size(&SOMETHING, ELEMENT, COUNT), GFP)
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL);
This patch makes the changes for kmalloc()-family (and kvmalloc()-family)
uses. It was done via automatic conversion with manual review for the
"CHECKME" non-standard cases noted below, using the following Coccinelle
script:
// pkey_cache = kmalloc(sizeof *pkey_cache + tprops->pkey_tbl_len *
// sizeof *pkey_cache->table, GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(*VAR->ELEMENT), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// mr = kzalloc(sizeof(*mr) + m * sizeof(mr->map[0]), GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(VAR->ELEMENT[0]), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// Same pattern, but can't trivially locate the trailing element name,
// or variable name.
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
expression SOMETHING, COUNT, ELEMENT;
@@
- alloc(sizeof(SOMETHING) + COUNT * sizeof(ELEMENT), GFP)
+ alloc(CHECKME_struct_size(&SOMETHING, ELEMENT, COUNT), GFP)
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Running sparse on the samsung clk directory has some noise that we can
fix to look for future problems easier.
drivers/clk/samsung/clk-s3c2443.c:111:26: warning: symbol 's3c2443_common_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:139:26: warning: symbol 's3c2443_common_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:152:27: warning: symbol 's3c2443_common_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:186:28: warning: symbol 's3c2443_common_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:241:26: warning: symbol 's3c2416_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:247:26: warning: symbol 's3c2416_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:253:27: warning: symbol 's3c2416_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:263:28: warning: symbol 's3c2416_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:291:26: warning: symbol 's3c2443_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:296:27: warning: symbol 's3c2443_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:305:28: warning: symbol 's3c2443_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:321:26: warning: symbol 's3c2450_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:328:26: warning: symbol 's3c2450_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:334:27: warning: symbol 's3c2450_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:345:28: warning: symbol 's3c2450_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:368:33: warning: symbol 's3c2443_common_frate_clks' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:464:49: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2443.c:470:49: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2443.c:476:49: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2412.c:96:26: warning: symbol 's3c2412_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:108:35: warning: symbol 's3c2412_ffactor' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:128:26: warning: symbol 's3c2412_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:146:27: warning: symbol 's3c2412_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:177:28: warning: symbol 's3c2412_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:227:33: warning: symbol 's3c2412_common_frate_clks' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:292:43: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2410.c:98:26: warning: symbol 's3c2410_common_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:114:26: warning: symbol 's3c2410_common_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:119:27: warning: symbol 's3c2410_common_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:138:28: warning: symbol 's3c2410_common_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:203:26: warning: symbol 's3c2410_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:207:35: warning: symbol 's3c2410_ffactor' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:218:28: warning: symbol 's3c2410_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:272:26: warning: symbol 's3c244x_common_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:277:35: warning: symbol 's3c244x_common_ffactor' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:294:26: warning: symbol 's3c244x_common_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:302:27: warning: symbol 's3c244x_common_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:306:28: warning: symbol 's3c244x_common_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:321:26: warning: symbol 's3c2440_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:325:27: warning: symbol 's3c2440_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:331:35: warning: symbol 's3c2442_ffactor' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:337:26: warning: symbol 's3c2442_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:346:33: warning: symbol 's3c2410_common_frate_clks' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:471:49: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2410.c:477:49: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2410.c:483:49: warning: Using plain integer as NULL pointer
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
This additional frequency is required for HDMI audio support
on Odroid U3 board.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
FIMC LITE SYSMMU devices are defined in exynos5250.dtsi, but clocks for
them are not instantiated by Exynos5250 clock provider driver. Add needed
definitions for those clocks to fix IOMMU probe failure:
ERROR: could not get clock /soc/sysmmu@13c40000:sysmmu(0)
exynos-sysmmu 13c40000.sysmmu: Failed to get device clock(s)!
exynos-sysmmu: probe of 13c40000.sysmmu failed with error -38
ERROR: could not get clock /soc/sysmmu@13c50000:sysmmu(0)
exynos-sysmmu 13c50000.sysmmu: Failed to get device clock(s)!
exynos-sysmmu: probe of 13c50000.sysmmu failed with error -38
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: bfed1074f213 ("clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks")
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Adding these EPLL output frequency entries allows to support all required
audio sample rates on the CODEC and the HDMI interface on Peach-Pit
Chromebook.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
This allows changing the EPLL output frequency through the audio subsystem
clock tree leaf clocks. This change is needed to support audio on the HDMI
interface on Peach-Pi(t) Chromebook.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Clocks related to DISP1 block require special handling for power domain
turn on/off sequences. Till now this was handled by Exynos power domain
driver, but that approach was limited only to some special cases. This
patch moves handling of those operations to clock controller driver.
This gives more flexibility and allows fine tune values of some
clock-specific registers. This patch moves handling of those mentioned
clocks to Exynos5 sub-CMU driver instantiated from Exynos5250 driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Clocks related to DISP, GSC and MFC blocks require special handling for
power domain turn on/off sequences. Till now this was handled by Exynos
power domain driver, but that approach was limited only to some special
cases. This patch moves handling of those operations to clock controller
driver. This gives more flexibility and allows fine tune values of some
clock-specific registers. This patch moves handling of those mentioned
clocks to Exynos5 sub-CMU driver instantiated from Exynos5420 driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Exynos5250/5420/5800 have only one clock controller, but some of their
clock depends on respective power domains. Handling integration of clock
controller and power domain can be done using runtime PM feature of CCF
framework. This however needs a separate struct device for each power
domain. This patch adds such separate driver for a group of such clocks,
which can be instantiated more than once, each time for a different
power domain.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Rates declared in PLL rate tables should match exactly rates calculated
from PLL coefficients. To avoid possible mistakes we can use compile
time validation.
The patch introduces such validators and expands all initializers
with additional input frequency parameter, required to validate rates.
Since S3C24xx PLLs requires different validators two new macros have
been introduced to deal with it. Also, since PLLs 4502 and 4508 have
different formulas PLL_45XX_RATE has been replaced with PLL_4508_RATE.
As the patch adds only compile time validators it should not have impact
on compiled code.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Rates declared in PLL rate tables should match exactly rates calculated
from PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Rates declared in PLL rate tables should match exactly rates calculated
from PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
In this patch an erroneous P value for 74176002 output frequency is also
corrected.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Add one more entry to the exynos5433_aud_pll_rates table, this allows
to support audio sample rates: 48000, 96000, 192000 Hz with minimum
error. The M, P, S, K values re confirmed by the HW team.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
The sclk_ioclk_i2s1_bclk clock is not currently handled by any driver
and disabling this clock by the clk core prevents proper operation
of the I2S1 block. CLK_IGNORE_UNUSED flag is added as a temporary fix.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
There is a error message within devm_ioremap_resource already,
so remove the dev_err call to avoid redundant error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
There is a error message within devm_ioremap_resource already,
so remove the dev_err call to avoid redundant error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
This patch just removes the unneeded enumeration for PLL index.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have two changes to the core framework this time around.
The first being a large change that introduces runtime PM support to
the clk framework. Now we properly call runtime PM operations on the
device providing a clk when the clk is in use. This helps on SoCs
where the clks provided by a device need something to be powered on
before using the clks, like power domains or regulators. It also helps
power those things down when clks aren't in use.
The other core change is a devm API addition for clk providers so we
can get rid of a bunch of clk driver remove functions that are just
doing of_clk_del_provider().
Outside of the core, we have the usual addition of clk drivers and
smattering of non-critical fixes to existing drivers. The biggest diff
is support for Mediatek MT2712 and MT7622 SoCs, but those patches
really just add a bunch of data.
By the way, we're trying something new here where we build the tree up
with topic branches. We plan to work this into our workflow so that we
don't step on each other's toes, and so the fixes branch can be merged
on an as-needed basis.
Summary:
Core:
- runtime PM support for clk providers
- devm API for of_clk_add_hw_provider()
New Drivers:
- Mediatek MT2712 and MT7622
- Renesas R-Car V3M SoC
Updates:
- runtime PM support for Samsung exynos5433/exynos4412 providers
- removal of clkdev aliases on Samsung SoCs
- convert clk-gpio to use gpio descriptors
- various driver cleanups to match kernel coding style
- Amlogic Video Processing Unit VPU and VAPB clks
- sigma-delta modulation for Allwinner audio PLLs
- Allwinner A83t Display clks
- support for the second display unit clock on Renesas RZ/G1E
- suspend/resume support for Renesas R-Car Gen3 CPG/MSSR
- new clock ids for Rockchip rk3188 and rk3368 SoCs
- various 'const' markings on clk_ops structures
- RPM clk support on Qualcomm MSM8996/MSM8660 SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits)
clk: stm32h7: fix test of clock config
clk: pxa: fix building on older compilers
clk: sunxi-ng: a83t: Fix i2c buses bits
clk: ti: dra7-atl-clock: fix child-node lookups
clk: qcom: common: fix legacy board-clock registration
clk: uniphier: fix DAPLL2 clock rate of Pro5
clk: uniphier: fix parent of miodmac clock data
clk: hi3798cv200: correct parent mux clock for 'clk_sdio0_ciu'
clk: hisilicon: Delete an error message for a failed memory allocation in hisi_register_clkgate_sep()
clk: hi3660: fix incorrect uart3 clock freqency
clk: kona-setup: Delete error messages for failed memory allocations
ARC: clk: fix spelling mistake: "configurarion" -> "configuration"
clk: cdce925: remove redundant check for non-null parent_name
clk: versatile: Improve sizeof() usage
clk: versatile: Delete error messages for failed memory allocations
clk: ux500: Improve sizeof() usage
clk: ux500: Delete error messages for failed memory allocations
clk: spear: Delete error messages for failed memory allocations
clk: ti: Delete error messages for failed memory allocations
clk: mmp: Adjust checks for NULL pointers
...
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk into clk-next
Pull Samsung clk driver updates from Sylwester Nawrocki:
- An addition of separate driver for the Exynos 4412 ISP CMU, needed
to model and properly handle the clock controller's dependencies
on the ISP power domain.
- Adding __maybe_unused attributes to the exynos5433_cmu_{suspend,
resume} ops to suppress compiler warnings with CONFIG_PM disabled.
* tag 'clk-v4.15-exynos-pm' of git://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk:
clk: samsung: Add a separate driver for Exynos4412 ISP clocks
clk: samsung: Add dt bindings for Exynos4412 ISP clock controller
clk: samsung: Instantiate Exynos4412 ISP clocks only when available
clk: samsung: exynos5433: mark PM functions as __maybe_unused
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk into clk-next
Pull Samsung clk driver updates from Sylwester Nawrocki:
Overall clk/samsung clean up and fixes. Removed remaining unused code
after removal of exynos4212 SoC support; dropped internal data structure
fields and related code for registering clkdev lookup entry for each
possible clock object, clkdev aliases could still be defined if needed
in a separate table; other minor fixes of the clock tree definitions.
* tag 'clk-v4.15-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk:
clk: samsung: Remove obsolete clkdev alias support
clk: samsung: Add explicit MPLL, EPLL clkdev aliases in S3C2443 driver
clk: samsung: Rework clkdev alias handling in S3C2443 driver
clk: samsung: Rework clkdev alias handling in Exynos5440 driver
clk: samsung: Drop useless alias in Exynos5420 clk driver
clk: samsung: Remove clkdev alias support in Exynos5250 clk driver
clk: samsung: Remove double assignment of CLK_ARM_CLK in Exynos4 driver
clk: samsung: Remove clkdev alias support in Exynos4 clk driver
clk: samsung: Remove support for obsolete Exynos4212 CPU clock
clk: samsung: Remove support for Exynos4212 SoCs in Exynos CLKOUT driver
clk: samsung: Properly propagate flags in __PLL macro
clk: samsung: Fix m2m scaler clock on Exynos542x
clk: samsung: Delete a memory allocation error message in clk-cpu.c
|
|
Some registers for the Exynos 4412 ISP (Camera subsystem) clocks are
located in the ISP power domain. Because those registers are also
located in a different memory region than the main clock controller,
support for them can be provided by a separate clock controller.
This in turn allows to almost seamlessly make it aware of the power
domain using recently introduced runtime PM support for clocks.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Some registers for the Exynos 4412 ISP (Camera subsystem) clocks are
located in the ISP power domain. Instantiate those clocks only when
provided clock registers resource covers those registers. This is
a preparation for adding a separate clock driver for ISP clocks,
which will be integrated with power domain using runtime PM feature.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
