| Age | Commit message (Collapse) | Author |
|---|
|
The clock bimc_gpu_clk_src is incorrectly set to use the shared rcg2
ops, which are for RCGs with child branches controlled by different
CPUs.
The result of the incorrect ops is that the GPU's PM runtime may leave
this clock set at a very low rate. Fix this issue by using the correct
rcg2 ops.
Fixes: a2e8272f3f89 ("clk: qcom: Add MSM8916 gpu clocks")
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
MCLK for internal audio codec is expected to be at 9.6MHz by default.
This patch adds support to 9.6MHz to make the default case possible.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The sdcc driver for msm8996/msm8916/msm8974/msm8994 and apq8084
expects a clk_set_rate() on the sdcc rcg clk to set
a floor value of supported clk rate closest to the requested
rate, by looking up the frequency table.
So move all the sdcc rcgs on all these platforms to use the
newly introduced clk_rcg2_floor_ops
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
This patch adds the CLK_SET_RATE_PARENT flag for the crypto core and
ahb blocks. Without this flag, clk_set_rate can fail for certain
frequency requests.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Fixes: 3966fab8b6ab ("clk: qcom: Add MSM8916 Global Clock Controller support")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
* clk-fixes:
clk: gpio: Really allow an optional clock= DT property
Revert "clk: qcom: Specify LE device endianness"
|
|
This reverts commit 329cabcecf94d8d7821e729dda284ba9dec44c87.
The commit that caused us to specify LE device endianness here,
29bb45f25ff3 (regmap-mmio: Use native endianness for read/write,
2015-10-29), has been reverted in mainline so now when we specify
LE it actively breaks big endian kernels because the byte
swapping in regmap-mmio is incorrect. Let's revert this change
because it will 1) fix the big endian kernels and 2) be redundant
to specify LE because that will become the default soon.
Cc: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
This clock is required for loading the qdsp firmware.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Move the xo and sleep clocks to device-tree, instead of hard-coding
them in the driver. This allows us to insert the RPM clocks (if they
are enabled) in between the on-board oscillators and the actual clock.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
All these clock controllers are little endian devices, but so far
we've been relying on the regmap mmio bus handling this for us
without explicitly stating that fact. After commit 4a98da2164cf
(regmap-mmio: Use native endianness for read/write, 2015-10-29),
the regmap mmio bus will read/write with the __raw_*() IO
accessors, instead of using the readl/writel() APIs that do
proper byte swapping for little endian devices.
So if we're running on a big endian processor and haven't
specified the endianness explicitly in the regmap config or in
DT, we're going to switch from doing little endian byte swapping
to big endian accesses without byte swapping, leading to some
confusing results. On my apq8074 dragonboard, this causes the
device to fail to boot as we access the clock controller with
big endian IO accesses even though the device is little endian.
Specify the endianness explicitly so that the regmap core
properly byte swaps the accesses for us.
Reported-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Now that qcom_cc_remove() is a nop, drop calls to
qcom_cc_remove() and any empty driver remove functions.
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add support for the msm8916 audio clocks. This includes core bus,
low-power audio and codec clocks. They are required for audio playback.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add support for the msm8916 BIMC (Bus Integrated Memory Controller)
clocks that are needed for GPU.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add support for the msm8916 TCU (Translation Control Unit) clocks that
are needed for IOMMU.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add all data for the GDSCs which are part of msm8916 GCC block.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Sometimes the display driver may want to change the parent PLL of
the display clocks (byte and pixel clocks) depending on the
use-case. Currently the parent is fixed by means of having a
frequency table with one entry that chooses a particular parent.
Remove this restriction and use the parent the clock is
configured for in the hardware during clk_set_rate(). This
requires consumers to rely on the default parent or to configure
the parent with clk_set_parent()/assigned-clock-parents on the
clocks before calling clk_set_rate().
Tested-by: Archit Taneja <architt@codeaurora.org>
Cc: Hai Li <hali@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Fix the enable bit of the pseudorandom number generator clock.
Reported-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Fixes: 3966fab8b6ab "clk: qcom: Add MSM8916 Global Clock Controller support"
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Make const both the array and the strings, so they can be
moved to .rodata section.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The gfx3d_clk_src parents configuration is incorrect. Fix it.
Fixes: 3966fab8b6ab "clk: qcom: Add MSM8916 Global Clock Controller support"
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
One of the video codec clock frequencies has incorrect divider
value. Fix it.
Fixes: 3966fab8b6ab "clk: qcom: Add MSM8916 Global Clock Controller support"
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
This patch adds support for the global clock controller found on the MSM8916
based devices. It allows the various device drivers to probe and control
their clocks and resets.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
[sboyd@codeaurora.org: Removed NULL entry from parent_maps]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
