| Age | Commit message (Collapse) | Author |
|---|
|
mpll0 clock is special compared to the other mplls. It needs another
bit (ssen) to be set to activate the fractional part the mpll divider
Fixes: 007e6e5c5f01 ("clk: meson: mpll: add rw operation")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
clk-next
Pull Amlogic clk driver updates from Jerome Brunet:
* Expose more clock gate on meson8 (SAR ADC, RNG, USB, SDIO, ETH)
* Add new compatible to the meson8 clock controller for meson8b
* Add missing parents to gxbb clk81
* tag 'meson-clk-for-4.13-2' of git://github.com/BayLibre/clk-meson:
clk: meson: gxbb: add all clk81 parents
clk: meson: meson8b: add compatibles for Meson8 and Meson8m2
clk: meson8b: export the ethernet gate clock
clk: meson8b: export the USB clocks
clk: meson8b: export the gate clock for the HW random number generator
clk: meson8b: export the SDIO clock
clk: meson8b: export the SAR ADC clocks
|
|
Remove the FIXME on clk81 mux and add all the documented parents
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
|
|
The clock controller on Meson8, Meson8b and Meson8m2 is very similar
based on the code from the Amlogic GPL kernel sources. Add separate
compatibles for each SoC to make sure that we can easily implement
all the small differences for each SoC later on.
In general the Meson8 and Meson8m2 seem to be almost identical as they
even share the same mach-meson8 directory in Amlogic's GPL kernel
sources.
The main clocks on Meson8, Meson8b and Meson8m2 are very similar,
because they are all using the same PLL values, 90% of the clock gates
are the same (the actual diffstat of the mach-meson8/clock.c and
mach-meson8b/clock.c files is around 30 to 40 lines, when excluding
all commented out code).
The difference between the Meson8 and Meson8b clock gates seem to be:
- Meson8 has AIU_PCLK, HDMI_RX, VCLK2_ENCT, VCLK2_ENCL, UART3,
CSI_DIG_CLKIN gates which don't seem to be available on Meson8b
- the gate on Meson8 for bit 7 seems to be named "_1200XXX" instead
of "PERIPHS_TOP" (on Meson8b)
- Meson8b has a SANA gate which doesn't seem to exist on Meson8 (or
on Meson8 the same bit is used by the UART3 gate in Amlogic's GPL
kernel sources)
None of these gates is added for now, since it's unclear whether these
definitions are actually correct (the VCLK2_ENCT gate for example is
defined, but only used in some commented block).
The main difference between all three SoCs seem to be the video (VPU)
clocks. Apart from different supported clock rates (according to vpu.c
in mach-meson8 and mach-meson8b from Amlogic's GPL kernel sources) the
most notable difference is that Meson8m2 has a GP_PLL clock and a mux
(probably the same as on the Meson GX SoCs) to support glitch-free
(clock rate) switching.
None of these VPU clocks are not supported by our mainline meson8b
clock driver yet though.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Export the ethernet gate clock to the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Export the USB related clocks (for the USB controller and the USB2 PHYs)
so they can be used in the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
This exports the clock so it can be used in the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Export the SDIO clock so it can be used in the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Export the clocks for the SAR ADC so they can be used in the
dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
These can be marked as const * const.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
clk-next
Pull Amlogic clock driver updates from Jerome Brunet:
* Expose more i2s and spdif output clocks
* Expose EE uart and SPICC gate clocks
* Remove cpu_clk from to gxbb
* Mark clk81 as critical on gxbb
* Add CEC EE clocks
* tag 'meson-clk-for-4.13' of git://github.com/BayLibre/clk-meson:
clk: meson-gxbb: Add EE 32K Clock for CEC
clk: gxbb: remove CLK_IGNORE_UNUSED from clk81
clk: meson: meson8b: mark clk81 as critical
clk: meson: gxbb: remove the "cpu_clk" from the GXBB and GXL driver
clk: meson-gxbb: un-export the CPU clock
clk: meson-gxbb: expose UART clocks
clk: meson-gxbb: expose SPICC gate
clk: meson-gxbb: expose spdif master clock
clk: meson-gxbb: expose i2s master clock
clk: meson-gxbb: expose spdif clock gates
|
|
On Amlogic GX SoCs, there is two CEC controllers :
- An Amlogic CEC custom in the AO domain
- The Synopsys HDMI-TX Controller in the EE domain
Each of these controllers needs a 32.768KHz clock, but there is two paths :
- In the EE domain, the "32k_clk" this patchs is adding
- In the AO domain, with a more complex dual divider more precise setup
The AO 32K clock support will be pushed later in the corresponding
gxbb-aoclk driver when the AE CEC driver is ready.
The EE 32k_clk must be pushed earlier since mainline support for CEC in the
Synopsys HDMI-TX controller is nearby.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[Rebased patch on top of last changes]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
clk81 already has CLK_IS_CRITICAL so CLK_IGNORE_UNUSED is not
necessary
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Disabling clk81 results in an immediate freeze of the whole system. This
can happen "accidentally" when the last child-clock of clk81 is disabled
(in this case the common clock framework also disables clk81, even if it
was only enabled indirectly before).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
It seems that the "cpu_clk" was carried over from the meson8b clock
controller driver. On Meson GX (GXBB/GXL/GXM) the registers which are
used by the cpu_clk have a different purpose (in other words: they don't
control the CPU clock anymore). HHI_SYS_CPU_CLK_CNTL1 bits 31:24 are
reserved according to the public S905 datasheet, while bit 23 is the
"A53_trace_clk_DIS" gate (which according to the datasheet should only
be used in case a silicon bug is discovered) and bits 22:20 are a
divider (A53_trace_clk). The meson clk-cpu code however expects that
bits 28:20 are reserved for a divider (according to the public S805
datasheet this "SCALE_DIV: This value represents an N+1 divider of the
input clock.").
The CPU clock on Meson GX SoCs is provided by the SCPI DVFS clock
driver instead. Two examples from a Meson GXL S905X SoC:
- vcpu (SCPI DVFS clock 0) rate: 1000000000 / cpu_clk rate: 708000000
- vcpu (SCPI DVFS clock 0) rate: 1512000000 / cpu_clk rate: 708000000
Unfortunately the CLKID_CPUCLK was already exported (but is currently
not used) to DT. Due to the removal of this clock definition there is
now a hole in the clk_hw_onecell_data (which is not a problem because
this case is already handled in gxbb_clkc_probe).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
The CPU clock defined in the Meson GX clock driver is actually a
left-over from the Meson8b clock controller. Un-export the clock so we
can remove it from the driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Expose the clock ids of the three none AO uarts to the dt-bindings
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[tidy the commit message to match similar change]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Expose the SPICC gate clock to enable the SPICC controller.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[tidy commit message to match similar changes]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Expose the spdif master clock and the mux to select the appropriate spdif
clock parent depending on the data source.
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Expose cts_amclk in the device tree bindings
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Expose the clock gates required for the spdif output
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
With CONFIG_RESET_CONTROLLER=n we see the following link error in the
meson gxbb clk driver:
drivers/built-in.o: In function 'gxbb_aoclkc_probe':
drivers/clk/meson/gxbb-aoclk.c:161: undefined reference to 'devm_reset_controller_register'
Fix this by selecting the reset controller subsystem.
Fixes: f8c11f79912d ("clk: meson: Add GXBB AO Clock and Reset controller driver")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: Added fixes-by tag]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Sort of on the quieter side this time, which is probably due more to
me not catching up as quickly on patch review than anything else.
Overall it seems normal though, a few small changes to the core,
mostly small non-critical fixes here and there as well as driver
updates for new and existing hardware support.
The biggest things are the TI clk driver rework to lay the groundwork
for clkctrl support in the next merge window and the AmLogic
audio/graphics clk support.
Core:
- clk_possible_parents debugfs file so we know which parents a clk
could possibly have
- Fix to make clk rate change notifiers stop on the first failure
instead of continuing
New Drivers:
- Mediatek MT6797 SoCs
- hi655x PMIC clks
- AmLogic Meson SoC i2s and spdif audio clks and Mali graphics clks
- Allwinner H5 SoCs and PRCM hardware
Updates:
- Nvidia Tegra T210 cleanups and non-critical fixes
- TI OMAP cleanups in preparation for clkctrl support
- trivial fixes like kcalloc(), devm_* conversions, and seq_puts()
- ZTE zx296718 SoC VGA clks
- Rockchip clk-ids, fixups, and rename of rk1108 to rv1108
- IDT VersaClock 5P49V5935 support
- Renesas R-Car H3 and M3-W IMR clks and ES2.0 rev of R-Car H3
support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (151 commits)
clk: x86: pmc-atom: Checking for IS_ERR() instead of NULL
clk: ti: divider: try to fix ti_clk_register_divider
clk: mvebu: Use kcalloc() in two functions
clk: mvebu: Use kcalloc() in of_cpu_clk_setup()
clk: nomadik: Delete error messages for a failed memory allocation in two functions
clk: nomadik: Use seq_puts() in nomadik_src_clk_show()
clk: Improve a size determination in two functions
clk: Replace four seq_printf() calls by seq_putc()
clk: si5351: Delete an error message for a failed memory allocation in si5351_i2c_probe()
clk: si5351: Use devm_kcalloc() in si5351_i2c_probe()
clk: at91: Use kcalloc() in of_at91_clk_pll_get_characteristics()
reset: mediatek: Add MT2701 ethsys reset controller include file
clk: mediatek: add mt2701 ethernet reset
clk: hi6220: Add the hi655x's pmic clock
clk: ti: fix building without legacy omap3
clk: ti: fix linker error with !SOC_OMAP4
clk: hi3620: Fix a typo in one variable name
clk: hi3620: Delete error messages for a failed memory allocation in two functions
clk: hi3620: Use kcalloc() in hi3620_mmc_clk_init()
clk: hisilicon: Delete error messages for failed memory allocations in hisi_clk_init()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Olof Johansson:
"Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch
of smaller changes, but also some new platforms that are worth
mentioning:
- Rockchip RK3399 platforms for Chromebooks, including Samsung
Chromebook Plus (Kevin)
- Orange Pi PC2 (Allwinner H5)
- Freescale LS2088A and LS1088A SoCs
- Expanded support for Nvidia Tegra186 (and Jetson TX2)"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (180 commits)
arm64: dts: Add basic DT to support Spreadtrum's SP9860G
arm64: dts: exynos: Use - instead of @ for DT OPP entries
arm64: dts: exynos: Add support for s6e3hf2 panel device on TM2e board
arm64: dts: juno: add information about L1 and L2 caches
arm64: dts: juno: fix few unit address format warnings
arm64: marvell: dts: enable the crypto engine on the Armada 8040 DB
arm64: marvell: dts: enable the crypto engine on the Armada 7040 DB
arm64: marvell: dts: add crypto engine description for 7k/8k
arm64: dts: marvell: add sdhci support for Armada 7K/8K
arm64: dts: marvell: add eMMC support for Armada 37xx
arm64: dts: hisi: add pinctrl dtsi file for HiKey960 development board
arm64: dts: hisi: add drive strength levels of the pins for Hi3660 SoC
arm64: dts: hisi: enable the NIC and SAS for the hip07-d05 board
arm64: dts: hisi: add SAS nodes for the hip07 SoC
arm64: dts: hisi: add RoCE nodes for the hip07 SoC
arm64: dts: hisi: add network related nodes for the hip07 SoC
arm64: dts: hisi: add mbigen nodes for the hip07 SoC
arm64: dts: rockchip: fix the memory size of PX5 Evaluation board
arm64: dts: hisilicon: add dts files for hi3798cv200-poplar board
dt-bindings: arm: hisilicon: add bindings for hi3798cv200 SoC and Poplar board
...
|
|
On Meson8b the MPLL parent clock (fixed_pll) has a rate of 2550MHz.
Multiplying this with SDM_DEN results in a value greater than 32bits.
This is not a problem on the 64bit Meson GX SoCs, but it may result in
undefined behavior on the older 32bit Meson8b SoC.
While rate_from_params was only introduced recently to make the math
reusable from _round_rate and _recalc_rate the original bug exists much
longer.
Fixes: 1c50da4f27 ("clk: meson: add mpll support")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[as discussed on the ml, use DIV_ROUND_UP_ULL]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
According to the public datasheet all register bits in HHI_MPLL_CNTL7,
HHI_MPLL_CNTL8 and HHI_MPLL_CNTL9 default to zero. On all GX SoCs these
seem to be initialized by the bootloader to some default value.
However, on my Meson8 board they are not initialized, leading to a
division by zero in rate_from_params as the math is:
(parent_rate * SDM_DEN) / ((SDM_DEN * 0) + 0)
According to the datasheet, the minimum n2 value is 4. The rate provided
by the clock when n2 is less than this minimum is unpredictable. In such
case, we report an error.
Although the rate_from_params function was only introduced recently the
original bug has been there for much longer. It was only exposed
recently when the MPLL clocks were added to the Meson8b clock driver.
Fixes: 1c50da4f27 ("clk: meson: add mpll support")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
This adds the cts_i958 clock to control the clock source of the spdif
output block. This mux is not explicitly mentionned in the documentation
but it is critical to the spdif dai. It is used to select whether the clock
source of the spdif output is cts_amclk (when data are taken from i2s
buffer) or the cts_mclk_i958 (when data are taken from the spdif buffer)
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Add the spdif master clock also referred as cts_mclk_i958
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Add the i2s master clock also referred as cts_amclk
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
The audio divider needs a specific clock divider driver.
With am mpll parent clock, which is able to provide a fairly precise rate,
the generic divider tends to select low value of the divider. In such case
the quality of the clock is very poor. For the same final rate, maximizing
the audio clock divider value and selecting the corresponding mpll rate
gives better results. This is what this driver aims to acheive. So far, so
good.
Cc: Hendrik v. Raven <hendrik@consetetur.de>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
The clock controller is getting more complex and it might be possible, in
the future, to have holes in the clk_hw_onecell_data array. Just make sure
we skip those holes if it ever happens.
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
* v4.12/clk-drivers:
clk: meson-gxbb: Add GXL/GXM GP0 Variant
clk: meson-gxbb: Add GP0 PLL init parameters
clk: meson: Add support for parameters for specific PLLs
clk: meson-gxbb: Add MALI clocks
clk: meson: mpll: correct N2 maximum value
clk: meson8b: add the mplls clocks 0, 1 and 2
clk: meson: gxbb: mpll: use rw operation
clk: meson: mpll: add rw operation
clk: gxbb: put dividers and muxes in tables
clk: meson8b: put dividers and muxes in tables
clk: meson: add missing const qualifiers on gate arrays
clk: meson: fix SET_PARM macro
|
|
The clock tree in the Amlogic GXBB and GXL/GXM SoCs is shared, but the GXL/GXM
SoCs embeds a different GP0 PLL, and needs different parameters with a vendor
provided reduced rate table.
This patch adds the GXL GP0 variant, and adds a GXL DT compatible in order
to use the GXL GP0 PLL instead of the GXBB specific one.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490178747-14837-4-git-send-email-narmstrong@baylibre.com
|
|
Tha Amlogic GXBB SoC GP0 PLL needs some vendor provided parameters to be
initializated in the the GP0 control registers before configuring the rate
with the rate table provided parameters.
GXBB GP0 PLL tweaks are also selected to respect the vendor init procedure.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490178747-14837-3-git-send-email-narmstrong@baylibre.com
|
|
In recent Amlogic GXBB, GXL and GXM SoCs, the GP0 PLL needs some specific
parameters in order to initialize and lock correctly.
This patch adds an optional PARAM table used to initialize the PLL to a
default value with it's parameters in order to achieve to desired frequency.
The GP0 PLL in GXBB, GXL/GXM also needs some tweaks in the initialization
steps, and these are exposed along the PARAM table.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490178747-14837-2-git-send-email-narmstrong@baylibre.com
|
|
The Mali is clocked by two identical clock paths behind a glitch free mux
to safely change frequency while running.
The two "mali_0" and "mali_1" clocks are composed of a mux, divider and gate.
Expose these two clocks trees using generic clocks.
Finally the glitch free mux is added as "mali" clock.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490177935-9646-3-git-send-email-narmstrong@baylibre.com
|
|
This patch exposes the GP0 PLL clock id in the dt bindings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490178747-14837-5-git-send-email-narmstrong@baylibre.com
|
|
Add missing MALI clock IDs and expose the muxes and gates in the dt-bindings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490177935-9646-2-git-send-email-narmstrong@baylibre.com
|
|
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-10-jbrunet@baylibre.com
|
|
Gxbb datasheet says N2 maximum value is 127 but the register field is
9 bits wide, the maximum value should 511.
Test shows value greater than 127, all the way to 511, works well
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-9-jbrunet@baylibre.com
|
|
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-8-jbrunet@baylibre.com
|
|
Use read/write operations for the mpll clocks instead of the
read-only ones.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-7-jbrunet@baylibre.com
|
|
This patch adds new callbacks to the meson-mpll driver to control
and set the pll rate. For this, we also need to add the enable bit and
sdm enable bit. The corresponding parameters are added to mpll data
structure.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-6-jbrunet@baylibre.com
|
|
Until now, there was only 2 dividers and 2 muxes declared for the gxbb
platform. With the ongoing work on various subsystem, including audio,
this is about to change. Use the same approach as gates for dividers and
muxes, putting them in tables to fix the register address at runtime.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-5-jbrunet@baylibre.com
|
|
Until now, there was only 1 divider and 1 mux declared for the meson8b
platform. With the ongoing work on various system, including audio, this
is about to change. Use the same approach as gates for dividers and muxes,
putting them in tables to fix the register address at runtime.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-4-jbrunet@baylibre.com
|
|
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-3-jbrunet@baylibre.com
|
|
parameter val is not enclosed in parenthesis which is buggy when given an
expression instead of a simple value
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-2-jbrunet@baylibre.com
|
|
Expose clock CLKID_RNG0 which is needed for the HW random number generator.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
This includes two branches for arm64 dt updates, both following up on
earlier changes for the same platforms that are already merged:
Samsung:
- add USB3 support in Exynos7
- minor PM related updates
Amlogic:
- new machines: WeTek Set-top-boxes
- various devices added to DT
There are also a couple of bugfixes that trickled in since the start
of the merge window:
- The moxart_defconfig was not building the intended platform
- CPU-hotplug was broken on ux500
- Coresight was broken on Juno (never worked)"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
ARM: deconfig: fix the moxart defconfig
ARM: ux500: resume the second core properly
arm64: dts: juno: update definition for programmable replicator
arm64: dts: exynos: Add regulators for Vbus and Vbus-Boost
arm64: dts: exynos: Add USB 3.0 controller node for Exynos7
arm64: dts: exynos: Use macros for pinctrl configuration on Exynos7
pinctrl: dt-bindings: samsung: Add Exynos7 specific pinctrl macro definitions
arm64: dts: exynos: Add initial configuration for DISP clocks for TM2/TM2e
ARM64: dts: meson-gxbb-p200: add ADC laddered keys
ARM64: dts: meson: meson-gx: add the SAR ADC
ARM64: dts: meson-gxl: add the pwm_ao_b pin
ARM64: dts: meson-gx: add the missing pwm_AO_ab node
clk: gxbb: fix CLKID_ETH defined twice
ARM64: dts: meson-gxl: rename Nexbox A95x for consistency
clk: gxbb: add the SAR ADC clocks and expose them
dt-bindings: amlogic: Add WeTek boards
ARM64: dts: meson-gxbb: Add support for WeTek Hub and Play
dt-bindings: vendor-prefix: Add wetek vendor prefix
ARM64: dts: meson-gxm: Rename q200 and q201 DT files for consistency
ARM64: dts: meson-gx: Add HDMI HPD/DDC pinctrl nodes
...
|
