| Age | Commit message (Collapse) | Author |
|---|
|
Clocks that don't have a divider are in our case all marked with the
CLK_SET_RATE_PARENT flag. In this case, the .round_rate implementation
should modify the value pointed to by parent_rate, in order to propagate
the rate change to the parent, as explained in the documentation of
clk_set_rate().
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903015048.3091523-5-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The custom clocks have custom functions to round, get or set their rate.
Therefore, we can't assume that they need the CLK_SET_RATE_PARENT flag.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903015048.3091523-4-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
CLK_SET_RATE_GATE means that the clock must be gated when being
reclocked. This is not the case for the PLLs in Ingenic SoCs.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903015048.3091523-3-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Use the readl_poll_timeout() function instead of rolling our own
busy-wait loops. This makes the code simpler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903015048.3091523-2-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The to_clk_info() previously had a BUG_ON() to check that it was only
called for PLL clocks. Yet, all the other clocks were doing the exact
same thing the macro does, in-line.
Move the to_clk_info() macro to the top of the file, remove the
hardcoded BUG_ON(), and use it everywhere it makes sense.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903015048.3091523-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add functions for calculat the rate of REFCLK, which is needed by
USB PHY in Ingenic X1000 SoC.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20200630163852.47267-4-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Reformat the code (add one level of indentation before the values),
to align the code in the macro definition section.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20200630163852.47267-3-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add new functions to "jz4780_otg_phy_ops" to enable or disable the
USB PHY in the JZ4780 SoC.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20200630163852.47267-2-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The RTC unit in the Ingenic SoCs has two clock sources, one
is from an external 32.768kHz clock, and the other is from an
external 24MHz/48MHz main clock that is divided by 512. The
choice of these two clocks is controlled by the ERCS bit in
the OPCR register. The RNG unit will also use this clock.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20200725051136.58220-4-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
This device id table is passed to of_match_node() later on in probe, but
on CONFIG_OF=n builds of_match_node() doesn't do anything with the
arguments. Lets just mark the table unused so that the compiler doesn't
complain about this.
drivers/clk/ingenic/tcu.c:326:34: warning: unused variable 'ingenic_tcu_of_match' [-Wunused-const-variable]
static const struct of_device_id ingenic_tcu_of_match[] __initconst = {
^
1 warning generated.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20200528233837.70269-1-sboyd@kernel.org
|
|
1.The SSI clock of X1000 not like JZ4770 and JZ4780, they are not
directly derived from the output of SSIPLL, but from the clock
obtained by dividing the frequency by 2. "X1000_CLK_SSIPLL_DIV2"
is added for this purpose, and ensure that it initialized before
"X1000_CLK_SSIMUX" when initializing the clocks.
2.Clocks of LCD, OTG, EMC, EFUSE, OST, TCU, and gates of CPU, PCLK
are also added.
3.Use "CLK_OF_DECLARE_DRIVER" like the other CGU drivers.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20200528031549.13846-8-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add support for the clocks provided by the CGU in the Ingenic X1830
SoC, making use of the cgu code to do the heavy lifting.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20200528031549.13846-6-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The PLL of X1830 Soc from Ingenic has been greatly changed,
the bypass control is placed in another register, so now two
registers may needed to control the PLL. To this end, a new
"bypass_reg" was introduced. In addition, when calculating
rate, the PLL of X1830 introduced an extra 2x multiplier,
so a new "rate_multiplier" was introduced. And adjust the
code in jz47xx-cgu.c and x1000-cgu.c, make it to be
compatible with the new cgu code.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20200528031549.13846-3-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
It is not necessary to use spinlock when reading registers,
so remove it from cgu.c.
Suggested-by: Paul Cercueil <paul@crapouillou.net>
Suggested-by: Paul Burton <paulburton@kernel.org>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20200528031549.13846-2-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
When requesting a rate superior to the parent's rate, it would return
-EINVAL instead of simply returning the parent's rate like it should.
Fixes: 4f89e4b8f121 ("clk: ingenic: Add driver for the TCU clocks")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20200213161952.37460-2-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Exit jz4770_cgu_init() if the 'cgu' pointer we get is NULL, since the
pointer is passed as argument to functions later on.
Fixes: 7a01c19007ad ("clk: Add Ingenic jz4770 CGU driver")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lkml.kernel.org/r/20200213161952.37460-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add "jz4780_core1_enable()" for enable the second core of JZ4780,
prepare for later commits.
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Paul Boddie <paul@boddie.org.uk>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Link: https://lkml.kernel.org/r/1582215889-113034-3-git-send-email-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
X1000 has a different TCU, since X1000 OST has been independent of TCU.
This patch is add TCU support of X1000, and prepare for later OST driver.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lkml.kernel.org/r/1584457893-40418-3-git-send-email-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
into clk-next
- Support CGU in Ingenix X1000
- Support Bitmain BM1880 clks
* clk-ingenic:
clk: ingenic: Allow drivers to be built with COMPILE_TEST
clk: Ingenic: Add CGU driver for X1000.
dt-bindings: clock: Add X1000 bindings.
* clk-init-leak:
clk: mark clk_disable_unused() as __init
clk: Fix memory leak in clk_unregister()
* clk-ux500:
MAINTAINERS: Update section for Ux500 clock drivers
* clk-bitmain:
MAINTAINERS: Add entry for BM1880 SoC clock driver
clk: Add common clock driver for BM1880 SoC
dt-bindings: clock: Add devicetree binding for BM1880 SoC
clk: Add clk_hw_unregister_composite helper function definition
clk: Zero init clk_init_data in helpers
|
|
We don't need the MIPS architecture or even a MIPS compiler to compile
test these drivers. Let's add a COMPILE_TEST possibility on the
menuconfig here so that we can build these drivers on more
configurations.
Cc: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20191114001925.159276-1-sboyd@kernel.org
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
|
|
Add support for the clocks provided by the CGU in the Ingenic X1000
SoC, making use of the cgu code to do the heavy lifting.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Link: https://lkml.kernel.org/r/1573378102-72380-3-git-send-email-zhouyanjie@zoho.com
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
There are a few manually-calculated variable-length struct allocations
left, this converts them to use struct_size. Found with the following
git grep command
git grep -A1 'kzalloc.*sizeof[^_].*+'
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lkml.kernel.org/r/20190927185110.29897-1-steve@sk2.org
Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
[sboyd@kernel.org: Add grep command]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
|
|
By using CLK_OF_DECLARE_DRIVER instead of the CLK_OF_DECLARE macro, we
allow the driver to probe also as a platform driver.
While this driver does not have code to probe as a platform driver, this
is still useful for probing children devices in the case where the
device node is compatible with "simple-mfd".
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20190810123620.27238-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add the missing TCU clock to the list of clocks supplied by the CGU for
the JZ4740 SoC.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: od@zcrc.me
|
|
Add driver to support the clocks provided by the Timer/Counter Unit
(TCU) of the JZ47xx SoCs from Ingenic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: od@zcrc.me
|
|
The code was setting the bit 21 of the CPCCR register to use a divider
of 2 for the "pll half" clock, and clearing the bit to use a divider
of 1.
This is the opposite of how this register field works: a cleared bit
means that the /2 divider is used, and a set bit means that the divider
is 1.
Restore the correct behaviour using the newly introduced .div_table
field.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20190701113606.4130-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round of clk driver and framework updates is heavy on the driver
update side. The two main highlights in the core framework are the
addition of an bulk clk_get API that handles optional clks and an
extra debugfs file that tells the developer about the current parent
of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is
mostly because that SoC has started converting to the clk_hw style of
clk registration. The next big update is in the Amlogic meson clk
driver that gained some support for audio, cpu, and temperature clks
while fixing some PLL issues. Finally, the biggest thing that stands
out is the conversion of a large part of the Allwinner sunxi-ng driver
to the new clk parent scheme that uses less strings and more pointer
comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks
here and there to clk data along with the normal addition of a handful
of new drivers and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (190 commits)
clk: consoldiate the __clk_get_hw() declarations
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: lochnagar: Update DT binding doc to include the primary SPDIF MCLK
clk: Add Si5341/Si5340 driver
dt-bindings: clock: Add silabs,si5341
clk: clk-si544: Implement small frequency change support
clk: add BCM63XX gated clock controller driver
devicetree: document the BCM63XX gated clock bindings
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: rockchip: export HDMIPHY clock on rk3228
clk: rockchip: add watchdog pclk on rk3328
clk: rockchip: add clock id for hdmi_phy special clock on rk3228
clk: rockchip: add clock id for watchdog pclk on rk3328
clk: at91: sckc: add support for SAM9X60
...
|
|
These functions are not called anywhere anymore, they can safely be
removed.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The Low-Power Mode, when enabled, will make the "wait" MIPS instruction
suspend the system.
This is not really clock-related, but this bit happens to be in the
register set of the CGU.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The cgu.h has structures that contain 'clk_onecell_data' and 'clk_hw'
structures (no pointers), so the <linux/clk-provider.h> header should be
included.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
[sboyd@kernel.org: Drop removal of includes in drivers]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The code was setting the bit 21 of the CPCCR register to use a divider
of 2 for the "pll half" clock, and clearing the bit to use a divider
of 1.
This is the opposite of how this register field works: a cleared bit
means that the /2 divider is used, and a set bit means that the divider
is 1.
Restore the correct behaviour using the newly introduced .div_table
field.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The main clocks (cclk, hclk, pclk, mclk, ipu) were using
incorrect dividers, and thus reported an incorrect rate.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The main clocks (cclk, h0clk, h1clk, h2clk, c1clk, pclk) were using
incorrect dividers, and thus reported an incorrect rate.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The main clocks (cclk, hclk, pclk, mclk, lcd) were using
incorrect dividers, and thus reported an incorrect rate.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Some clocks provided on Ingenic SoCs have dividers, whose hardware value
as written in the register cannot be expressed as an affine function
to the actual divider value.
For instance, for the CPU clock on the JZ4770, the dividers are coded as
follows:
------------------
| Bits | Div |
------------------
| 0 0 0 | 1 |
| 0 0 1 | 2 |
| 0 1 0 | 3 |
| 0 1 1 | 4 |
| 1 0 0 | 6 |
| 1 0 1 | 8 |
| 1 1 0 | 12 |
------------------
To support this setup, we introduce a new field in the
ingenic_cgu_div_info structure that allows to specify the divider table.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that we've gotten rid of clk_readl() we can remove io.h from the
clk-provider header and push out the io.h include to any code that isn't
already including the io.h header but using things like readl/writel,
etc.
Found with this grep:
git grep -l clk-provider.h | grep '.c$' | xargs git grep -L 'linux/io.h' | \
xargs git grep -l \
-e '\<__iowrite32_copy\>' --or \
-e '\<__ioread32_copy\>' --or \
-e '\<__iowrite64_copy\>' --or \
-e '\<ioremap_page_range\>' --or \
-e '\<ioremap_huge_init\>' --or \
-e '\<arch_ioremap_pud_supported\>' --or \
-e '\<arch_ioremap_pmd_supported\>' --or \
-e '\<devm_ioport_map\>' --or \
-e '\<devm_ioport_unmap\>' --or \
-e '\<IOMEM_ERR_PTR\>' --or \
-e '\<devm_ioremap\>' --or \
-e '\<devm_ioremap_nocache\>' --or \
-e '\<devm_ioremap_wc\>' --or \
-e '\<devm_iounmap\>' --or \
-e '\<devm_ioremap_release\>' --or \
-e '\<devm_memremap\>' --or \
-e '\<devm_memunmap\>' --or \
-e '\<__devm_memremap_pages\>' --or \
-e '\<pci_remap_cfgspace\>' --or \
-e '\<arch_has_dev_port\>' --or \
-e '\<arch_phys_wc_add\>' --or \
-e '\<arch_phys_wc_del\>' --or \
-e '\<memremap\>' --or \
-e '\<memunmap\>' --or \
-e '\<arch_io_reserve_memtype_wc\>' --or \
-e '\<arch_io_free_memtype_wc\>' --or \
-e '\<__io_aw\>' --or \
-e '\<__io_pbw\>' --or \
-e '\<__io_paw\>' --or \
-e '\<__io_pbr\>' --or \
-e '\<__io_par\>' --or \
-e '\<__raw_readb\>' --or \
-e '\<__raw_readw\>' --or \
-e '\<__raw_readl\>' --or \
-e '\<__raw_readq\>' --or \
-e '\<__raw_writeb\>' --or \
-e '\<__raw_writew\>' --or \
-e '\<__raw_writel\>' --or \
-e '\<__raw_writeq\>' --or \
-e '\<readb\>' --or \
-e '\<readw\>' --or \
-e '\<readl\>' --or \
-e '\<readq\>' --or \
-e '\<writeb\>' --or \
-e '\<writew\>' --or \
-e '\<writel\>' --or \
-e '\<writeq\>' --or \
-e '\<readb_relaxed\>' --or \
-e '\<readw_relaxed\>' --or \
-e '\<readl_relaxed\>' --or \
-e '\<readq_relaxed\>' --or \
-e '\<writeb_relaxed\>' --or \
-e '\<writew_relaxed\>' --or \
-e '\<writel_relaxed\>' --or \
-e '\<writeq_relaxed\>' --or \
-e '\<readsb\>' --or \
-e '\<readsw\>' --or \
-e '\<readsl\>' --or \
-e '\<readsq\>' --or \
-e '\<writesb\>' --or \
-e '\<writesw\>' --or \
-e '\<writesl\>' --or \
-e '\<writesq\>' --or \
-e '\<inb\>' --or \
-e '\<inw\>' --or \
-e '\<inl\>' --or \
-e '\<outb\>' --or \
-e '\<outw\>' --or \
-e '\<outl\>' --or \
-e '\<inb_p\>' --or \
-e '\<inw_p\>' --or \
-e '\<inl_p\>' --or \
-e '\<outb_p\>' --or \
-e '\<outw_p\>' --or \
-e '\<outl_p\>' --or \
-e '\<insb\>' --or \
-e '\<insw\>' --or \
-e '\<insl\>' --or \
-e '\<outsb\>' --or \
-e '\<outsw\>' --or \
-e '\<outsl\>' --or \
-e '\<insb_p\>' --or \
-e '\<insw_p\>' --or \
-e '\<insl_p\>' --or \
-e '\<outsb_p\>' --or \
-e '\<outsw_p\>' --or \
-e '\<outsl_p\>' --or \
-e '\<ioread8\>' --or \
-e '\<ioread16\>' --or \
-e '\<ioread32\>' --or \
-e '\<ioread64\>' --or \
-e '\<iowrite8\>' --or \
-e '\<iowrite16\>' --or \
-e '\<iowrite32\>' --or \
-e '\<iowrite64\>' --or \
-e '\<ioread16be\>' --or \
-e '\<ioread32be\>' --or \
-e '\<ioread64be\>' --or \
-e '\<iowrite16be\>' --or \
-e '\<iowrite32be\>' --or \
-e '\<iowrite64be\>' --or \
-e '\<ioread8_rep\>' --or \
-e '\<ioread16_rep\>' --or \
-e '\<ioread32_rep\>' --or \
-e '\<ioread64_rep\>' --or \
-e '\<iowrite8_rep\>' --or \
-e '\<iowrite16_rep\>' --or \
-e '\<iowrite32_rep\>' --or \
-e '\<iowrite64_rep\>' --or \
-e '\<__io_virt\>' --or \
-e '\<pci_iounmap\>' --or \
-e '\<virt_to_phys\>' --or \
-e '\<phys_to_virt\>' --or \
-e '\<ioremap_uc\>' --or \
-e '\<ioremap\>' --or \
-e '\<__ioremap\>' --or \
-e '\<iounmap\>' --or \
-e '\<ioremap\>' --or \
-e '\<ioremap_nocache\>' --or \
-e '\<ioremap_uc\>' --or \
-e '\<ioremap_wc\>' --or \
-e '\<ioremap_wc\>' --or \
-e '\<ioremap_wt\>' --or \
-e '\<ioport_map\>' --or \
-e '\<ioport_unmap\>' --or \
-e '\<ioport_map\>' --or \
-e '\<ioport_unmap\>' --or \
-e '\<xlate_dev_kmem_ptr\>' --or \
-e '\<xlate_dev_mem_ptr\>' --or \
-e '\<unxlate_dev_mem_ptr\>' --or \
-e '\<virt_to_bus\>' --or \
-e '\<bus_to_virt\>' --or \
-e '\<memset_io\>' --or \
-e '\<memcpy_fromio\>' --or \
-e '\<memcpy_toio\>'
I also reordered a couple includes when they weren't alphabetical and
removed clk.h from kona, replacing it with clk-provider.h because
that driver doesn't use clk consumer APIs.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: John Crispin <john@phrozen.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add clock for the USB Device Controller PHY.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/clk/ingenic/cgu.c: In function 'ingenic_pll_recalc_rate':
drivers/clk/ingenic/cgu.c:86:15: warning:
variable 'enable' set but not used [-Wunused-but-set-variable]
It's not used after commit ab27eb4bc365 ("clk: ingenic: Add code to
enable/disable PLLs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The 'div' field does not represent a number of bits used to divide
(understand: right-shift) the divider, but a number itself used to
divide the divider.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Take a parent rate of 180 MHz, and a requested rate of 4.285715 MHz.
This results in a theorical divider of 41.999993 which is then rounded
up to 42. The .round_rate function would then return (180 MHz / 42) as
the clock, rounded down, so 4.285714 MHz.
Calling clk_set_rate on 4.285714 MHz would round the rate again, and
give a theorical divider of 42,0000028, now rounded up to 43, and the
rate returned would be (180 MHz / 43) which is 4.186046 MHz, aka. not
what we requested.
Fix this by rounding up the divisions.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Maarten ter Huurne <maarten@treewalker.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The UDC clock is gated when the bit is cleared, not when it is set.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Fixes: 2b555a4b9cae ("clk: ingenic: Add missing flag for UDC clock")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add support for the clocks provided by the CGU in the Ingenic JZ4725B
SoC.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Previously, the CGU code corresponding to the SoC for which we're
compiling the kernel was the only one enabled, which made it impossible
to build one kernel that supports them all.
Now, it is possible to select more than one SoC to support.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The UDC clock of the JZ4740 SoC can be gated, but the data structure
representing it was missing the CGU_CLK_GATE flag to make it work.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The register field for configuring the divider for the i2s clock
occupies the bits [8-0], which means 9 bits and not 8.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
As we move stuff around, some doc references are broken. Fix some of
them via this script:
./scripts/documentation-file-ref-check --fix
Manually checked if the produced result is valid, removing a few
false-positives.
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
|
|
This is required, as we must not use the AHB1 bus before it is stable.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
