| Age | Commit message (Collapse) | Author |
|---|
|
msg_written_handler() may set ssif_info->multi_data to NULL
when using ipmitool to write fru.
Before setting ssif_info->multi_data to NULL, add new local
pointer "data_to_send" and store correct i2c data pointer to
it to fix NULL pointer kernel panic and incorrect ssif_info->multi_pos.
Signed-off-by: Joeseph Chang <joechang@codeaurora.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org # 3.19-
|
|
We try to disable callbacks on c_ivq even without multiport
even though that vq is not initialized in this configuration.
Fixes: c743d09dbd01 ("virtio: console: Disable callbacks for virtqueues at start of S4 freeze")
Suggested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Merge the crypto tree to resolve conflict between caam changes.
|
|
This enables TPM Command Response Buffer interface driver for
ARM64 and implements an ARM specific TPM CRB start method that
invokes a Secure Monitor Call (SMC) to request the TrustZone
Firmware to execute or cancel a TPM 2.0 command.
In ARM, TrustZone security extensions enable a secure software
environment with Secure Monitor mode. A Secure Monitor Call
(SMC) is used to enter the Secure Monitor mode and perform a
Secure Monitor service to communicate with TrustZone firmware
which has control over the TPM hardware.
Signed-off-by: Jiandi An <anjiandi@codeaurora.org>
Tested-by: Shanker Donthineni <shankerd@codeaurora.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> (on x86/PTT)
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
This commit adds support for requesting and relinquishing locality 0 in
tpm_crb for the course of command transmission.
In order to achieve this, two new callbacks are added to struct
tpm_class_ops:
- request_locality
- relinquish_locality
With CRB interface you first set either requestAccess or relinquish bit
from TPM_LOC_CTRL_x register and then wait for locAssigned and
tpmRegValidSts bits to be set in the TPM_LOC_STATE_x register.
The reason why were are doing this is to make sure that the driver
will work properly with Intel TXT that uses locality 2. There's no
explicit guarantee that it would relinquish this locality. In more
general sense this commit enables tpm_crb to be a well behaving
citizen in a multi locality environment.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Jerry Snitselaar <jsnitsel@redhat.com>
|
|
Since check_locality is checking to see if a certain
locality is active, return true if active otherwise
return false.
Cc: Christophe Ricard <christophe.ricard@gmail.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Marcel Selhorst <tpmdd@selhorst.net>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
When PM_SLEEP is disabled crb_pm_suspend and crb_pm_resume are not used by
SET_SYSTEM_SLEEP_PM_OPS even if PM is enabled:
drvers/char/tpm/tpm_crb.c:540:12: warning: ‘crb_pm_suspend’ defined but not
used [-Wunused-function]
static int crb_pm_suspend(struct device *dev)
^
drivers/char/tpm/tpm_crb.c:551:12: warning: ‘crb_pm_resume’ defined but not
used [-Wunused-function]
static int crb_pm_resume(struct device *dev)
^
The preprocessor condition should be on CONFIG_PM_SLEEP, not on CONFIG_PM.
However, this patch fixes this warning by using __maybe_unused on function
that are in the preprocessor condition.
Fixes: 848efcfb560c ("tpm/tpm_crb: enter the low power state upon device suspend")
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Currently, there is an unnecessary 1 msec delay added in
i2c_nuvoton_write_status() for the successful case. This
function is called multiple times during send() and recv(),
which implies adding multiple extra delays for every TPM
operation.
This patch calls usleep_range() only if retry is to be done.
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org (linux-4.8)
Reviewed-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
In order to make GPIO ACPI library stricter prepare users of
gpiod_get_index() to correctly behave when there no mapping is
provided by firmware.
Here we add explicit mapping between _CRS GpioIo() resources and
their names used in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
The current code passes the address of tpm_chip as the argument to
dev_get_drvdata() without prior NULL check in
tpm_ibmvtpm_get_desired_dma. This resulted an oops during kernel
boot when vTPM is enabled in Power partition configured in active
memory sharing mode.
The vio_driver's get_desired_dma() is called before the probe(), which
for vtpm is tpm_ibmvtpm_probe, and it's this latter function that
initializes the driver and set data. Attempting to get data before
the probe() caused the problem.
This patch adds a NULL check to the tpm_ibmvtpm_get_desired_dma.
fixes: 9e0d39d8a6a0 ("tpm: Remove useless priv field in struct tpm_vendor_specific")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkine <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Make sure size of response buffer is at least 6 bytes, or
we will underflow and pass large size_t to memcpy_fromio().
This was encountered while testing earlier version of
locality patchset.
Cc: stable@vger.kernel.org
Fixes: 30fc8d138e912 ("tpm: TPM 2.0 CRB Interface")
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Sessions are different from transient objects in that their handles
may not be virtualized (because they're used for some hmac
calculations). Additionally when a session is context saved, a
vestigial memory remains in the TPM and if it is also flushed, that
will be lost and the session context will refuse to load next time, so
the code is updated to flush only transient objects after a context
save. Add a separate array (chip->session_tbl) to save and restore
sessions by handle. Use the failure of a context save or load to
signal that the session has been flushed from the TPM and we can
remove its memory from chip->session_tbl.
Sessions are also isolated during each instance of a tpm space. This
means that spaces shouldn't be able to see each other's sessions and
is enforced by ensuring that a space user may only refer to sessions
handles that are present in their own chip->session_tbl. Finally when
a space is closed, all the sessions belonging to it should be flushed
so the handles may be re-used by other spaces.
Note that if we get a session save or load error, all sessions are
effectively flushed. Even though we restore the session buffer, all
the old sessions will refuse to load after the flush and they'll be
purged from our session memory. This means that while transient
context handling is still soft in the face of errors, session handling
is hard (any failure of the model means all sessions are lost).
Fixes-from: Colin Ian King <colin.king@canonical.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Currently the tpm spaces are not exposed to userspace. Make this
exposure via a separate device, which can now be opened multiple times
because each read/write transaction goes separately via the space.
Concurrency is protected by the chip->tpm_mutex for each read/write
transaction separately. The TPM is cleared of all transient objects
by the time the mutex is dropped, so there should be no interference
between the kernel and userspace.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Added an ability to virtualize TPM commands into an isolated context
that we call a TPM space because the word context is already heavily
used in the TPM specification. Both the handle areas and bodies (where
necessary) are virtualized.
The mechanism works by adding a new parameter struct tpm_space to the
tpm_transmit() function. This new structure contains the list of virtual
handles and a buffer of page size (currently) for backing storage.
When tpm_transmit() is called with a struct tpm_space instance it will
execute the following sequence:
1. Take locks.
2. Load transient objects from the backing storage by using ContextLoad
and map virtual handles to physical handles.
3. Perform the transaction.
4. Save transient objects to backing storage by using ContextSave and
map resulting physical handle to virtual handle if there is such.
This commit does not implement virtualization support for hmac and
policy sessions.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Check for every TPM 2.0 command that the command code is supported and
the command buffer has at least the length that can contain the header
and the handle area.
For ContextSave and FlushContext we mark the body to be part of the
handle area. This gives validation for these commands at zero
cost, including the body of the command.
The more important reason for this is that we can virtualize these
commands in the same way as you would virtualize the handle area of a
command.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Check that the length matches the length reported by the response
header already in tpm_transmit() to improve validation.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Encapsulated crb_wait_for_reg32() so that state changes in other CRB
registers than TPM_CRB_CTRL_REQ_x can be waited.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Gang Wei <gang.wei@intel.com>
|
|
In order to provide access to locality registers, this commits adds
mapping of the head of the CRB registers, which are located right
before the control area.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Gang Wei <gang.wei@intel.com>
|
|
Testing the implementation with a Raspberry Pi 2 showed that under some
circumstances its SPI master erroneously releases the CS line before the
transfer is complete, i.e. before the end of the last clock. In this case
the TPM ignores the transfer and misses for example the GO command. The
driver is unable to detect this communication problem and will wait for a
command response that is never going to arrive, timing out eventually.
As a workaround, the small delay ensures that the CS line is held long
enough, even with a faulty SPI master. Other SPI masters are not affected,
except for a negligible performance penalty.
Cc: <stable@vger.kernel.org>
Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Limiting transfers to MAX_SPI_FRAMESIZE was not expected by the upper
layers, as tpm_tis has no such limitation. Add a loop to hide that
limitation.
v2: Moved scope of spi_message to the top as requested by Jarkko
Cc: <stable@vger.kernel.org>
Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Wait states are signaled in the last byte received from the TPM in
response to the header, not the first byte. Check rx_buf[3] instead of
rx_buf[0].
Cc: <stable@vger.kernel.org>
Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Abort the transfer with ETIMEDOUT when the TPM signals more than
TPM_RETRY wait states. Continuing with the transfer in this state
will only lead to arbitrary failures in other parts of the code.
Cc: <stable@vger.kernel.org>
Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
The algorithm for sending data to the TPM is mostly identical to the
algorithm for receiving data from the TPM, so a single function is
sufficient to handle both cases.
This is a prequisite for all the other fixes, so we don't have to fix
everything twice (send/receive)
v2: u16 instead of u8 for the length.
Cc: <stable@vger.kernel.org>
Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Benoit Houyere <benoit.houyere@st.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
This fix enables a platform to enter the idle state (suspend-to-idle)
The driver needs to request explicitly go_idle upon completion
from the pm suspend handler.
The runtime pm is disabled on suspend during prepare state by calling
pm_runtime_get_noresume, hence we cannot relay on runtime pm to leave
the device in low power state. Symmetrically cmdReady is called
upon resume.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Siged-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
We get a newly introduced harmless warning when CONFIG_CRYPTO is disabled:
warning: (TCG_TPM && TRUSTED_KEYS && IMA) selects CRYPTO_HASH_INFO which has unmet direct dependencies (CRYPTO)
This adds another select to avoid the warning, consistent with other users
of the crypto code.
Fixes: c1f92b4b04ad ("tpm: enhance TPM 2.0 PCR extend to support multiple banks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Commit 500462a9de65 "timers: Switch to a non-cascading wheel" replaced
the 'classic' timer wheel, which aimed for near 'exact' expiry of the
timers. Their analysis was that the vast majority of timeout timers
are used as safeguards, not as real timers, and are cancelled or
rearmed before expiration. The only exception noted to this were
networking timers with a small expiry time.
Not included in the analysis was the TPM polling timer, which resulted
in a longer normal delay and, every so often, a very long delay. The
non-cascading wheel delay is based on CONFIG_HZ. For a description of
the different rings and their delays, refer to the comments in
kernel/time/timer.c.
Below are the delays given for rings 0 - 2, which explains the longer
"normal" delays and the very, long delays as seen on systems with
CONFIG_HZ 250.
* HZ 1000 steps
* Level Offset Granularity Range
* 0 0 1 ms 0 ms - 63 ms
* 1 64 8 ms 64 ms - 511 ms
* 2 128 64 ms 512 ms - 4095 ms (512ms - ~4s)
* HZ 250
* Level Offset Granularity Range
* 0 0 4 ms 0 ms - 255 ms
* 1 64 32 ms 256 ms - 2047 ms (256ms - ~2s)
* 2 128 256 ms 2048 ms - 16383 ms (~2s - ~16s)
Below is a comparison of extending the TPM with 1000 measurements,
using msleep() vs. usleep_delay() when configured for 1000 hz vs. 250
hz, before and after commit 500462a9de65.
linux-4.7 | msleep() usleep_range()
1000 hz: 0m44.628s | 1m34.497s 29.243s
250 hz: 1m28.510s | 4m49.269s 32.386s
linux-4.7 | min-max (msleep) min-max (usleep_range)
1000 hz: 0:017 - 2:760s | 0:015 - 3:967s 0:014 - 0:418s
250 hz: 0:028 - 1:954s | 0:040 - 4:096s 0:016 - 0:816s
This patch replaces the msleep() with usleep_range() calls in the
i2c nuvoton driver with a consistent max range value.
Signed-of-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org (linux-4.8)
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
The expectation is that the if the CRB cmd/rsp buffer falls within the
ACPI region that the entire buffer will be within the reason. Otherwise
resource reservation will fail when it crosses regions.
Work around this BIOS bug by limiting the cmd/rsp buffer to the length
of the declared ACPI region. BIOS vendors should fix this by making
the ACPI and register length declarations consistent.
Reported-by: Davide Guerri <davide.guerri@gmail.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Davide Guerri <davide.guerri@gmail.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
TIS v1.3 for TPM 1.2 and PTP for TPM 2.0 disagree about which timeout
value applies to reading a valid burstcount. It is TIMEOUT_D according to
TIS, but TIMEOUT_A according to PTP, so choose the appropriate value
depending on whether we deal with a TPM 1.2 or a TPM 2.0.
This is important since according to the PTP TIMEOUT_D is much smaller
than TIMEOUT_A. So the previous implementation could run into timeouts
with a TPM 2.0, even though the TPM was behaving perfectly fine.
During tpm2_probe TIMEOUT_D will be used even with a TPM 2.0, because
TPM_CHIP_FLAG_TPM2 is not yet set. This is fine, since the timeout values
will only be changed afterwards by tpm_get_timeouts. Until then
TIS_TIMEOUT_D_MAX applies, which is large enough.
Cc: stable@vger.kernel.org
Fixes: aec04cbdf723 ("tpm: TPM 2.0 FIFO Interface")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Linux 4.11-rc4
The i915 GVT team need the rc4 code to base some more code on.
|
|
We want the char-misc fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"A smattering of different small fixes for some random driver
subsystems. Nothing all that major, just resolutions for reported
issues and bugs.
All have been in linux-next with no reported issues"
* tag 'char-misc-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (21 commits)
extcon: int3496: Set the id pin to direction-input if necessary
extcon: int3496: Use gpiod_get instead of gpiod_get_index
extcon: int3496: Add dependency on X86 as it's Intel specific
extcon: int3496: Add GPIO ACPI mapping table
extcon: int3496: Rename GPIO pins in accordance with binding
vmw_vmci: handle the return value from pci_alloc_irq_vectors correctly
ppdev: fix registering same device name
parport: fix attempt to write duplicate procfiles
auxdisplay: img-ascii-lcd: add missing sentinel entry in img_ascii_lcd_matches
Drivers: hv: vmbus: Don't leak memory when a channel is rescinded
Drivers: hv: vmbus: Don't leak channel ids
Drivers: hv: util: don't forget to init host_ts.lock
Drivers: hv: util: move waiting for release to hv_utils_transport itself
vmbus: remove hv_event_tasklet_disable/enable
vmbus: use rcu for per-cpu channel list
mei: don't wait for os version message reply
mei: fix deadlock on mei reset
intel_th: pci: Add Gemini Lake support
intel_th: pci: Add Denverton SOC support
intel_th: Don't leak module refcount on failure to activate
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes regressions in the crypto ccp driver and the hwrng drivers
for amd and geode"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: geode - Revert managed API changes
hwrng: amd - Revert managed API changes
crypto: ccp - Assign DMA commands to the channel's CCP
|
|
Merging 4.11-rc3 to pick up md5 removal from /dev/random.
|
|
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Linux 4.11-rc3 as requested by Daniel
|
|
Replace the open coded registration of the cdev and dev with the
new device_add_cdev() helper. The helper replaces a common pattern by
taking the proper reference against the parent device and adding both
the cdev and the device.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
To enable eventual removal of pr_warning
This makes pr_warn use consistent for drivers/char
Prior to this patch, there were 1 use of pr_warning and
40 uses of pr_warn in drivers/char
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Amit Shah <amit@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The value passed by the two callers of the function is unsigned anyway.
Making the parameter unsigned fixes the following warning when building
with clang:
drivers/char/hpet.c:588:7: error: overflow converting case value to switch condition type (2149083139 to 18446744071563667459) [-Werror,-Wswitch]
case HPET_INFO:
^
include/uapi/linux/hpet.h:18:19: note: expanded from macro 'HPET_INFO'
^
include/uapi/asm-generic/ioctl.h:77:28: note: expanded from macro '_IOR'
^
include/uapi/asm-generic/ioctl.h:66:2: note: expanded from macro '_IOC'
(((dir) << _IOC_DIRSHIFT) | \
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, the code that takes a reference to the clock and enables it
is located inside of_get_omap_rng_device_details(), called only when
probing through the Device Tree.
However, there is nothing that makes this clock logic dependent on the
Device Tree, so it makes more sense to have it in omap_rng_probe()
directly.
Moreover, we make sure to bail out if we can't enable the clock. Indeed,
while the clock is optional, if a clock is present, we really want to
succeed in enabling it. And we fix the error message to fit on one line,
so that it is grep-friendly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add handling of RNG0 clock to the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
After commit e9afc746299d ("hwrng: geode - Use linux/io.h instead of
asm/io.h") the geode-rng driver uses devres with pci_dev->dev to keep
track of resources, but does not actually register a PCI driver. This
results in the following issues:
1. The driver leaks memory because the driver does not attach to a
device. The driver only uses the PCI device as a reference. devm_*()
functions will release resources on driver detach, which the geode-rng
driver will never do. As a result,
2. The driver cannot be reloaded because there is always a use of the
ioport and region after the first load of the driver.
Revert the changes made by e9afc746299d ("hwrng: geode - Use linux/io.h
instead of asm/io.h").
Cc: <stable@vger.kernel.org>
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Fixes: 6e9b5e76882c ("hwrng: geode - Migrate to managed API")
Cc: Matt Mackall <mpm@selenic.com>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-geode@lists.infradead.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
After commit 31b2a73c9c5f ("hwrng: amd - Migrate to managed API"), the
amd-rng driver uses devres with pci_dev->dev to keep track of resources,
but does not actually register a PCI driver. This results in the
following issues:
1. The message
WARNING: CPU: 2 PID: 621 at drivers/base/dd.c:349 driver_probe_device+0x38c
is output when the i2c_amd756 driver loads and attempts to register a PCI
driver. The PCI & device subsystems assume that no resources have been
registered for the device, and the WARN_ON() triggers since amd-rng has
already do so.
2. The driver leaks memory because the driver does not attach to a
device. The driver only uses the PCI device as a reference. devm_*()
functions will release resources on driver detach, which the amd-rng
driver will never do. As a result,
3. The driver cannot be reloaded because there is always a use of the
ioport and region after the first load of the driver.
Revert the changes made by 31b2a73c9c5f ("hwrng: amd - Migrate to managed
API").
Cc: <stable@vger.kernel.org>
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Fixes: 31b2a73c9c5f ("hwrng: amd - Migrate to managed API").
Cc: Matt Mackall <mpm@selenic.com>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: linux-crypto@vger.kernel.org
Cc: linux-geode@lists.infradead.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Usually every parallel port will have a single pardev registered with
it. But ppdev driver is an exception. This userspace parallel port
driver allows to create multiple parrallel port devices for a single
parallel port. And as a result we were having a big warning like:
"sysfs: cannot create duplicate filename '/devices/parport0/ppdev0.0'".
And with that many parallel port printers stopped working.
We have been using the minor number as the id field while registering
a parralel port device with a parralel port. But when there are
multiple parrallel port device for one single parallel port, they all
tried to register with the same name like 'pardev0.0' and everything
started failing.
Use an incremented index as the id instead of the minor number.
Fixes: 8b7d3a9d903e ("ppdev: use new parport device model")
Cc: stable <stable@vger.kernel.org> # v4.9+
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1414656
Bugzilla: https://bugs.archlinux.org/task/52322
Tested-by: James Feeney <james@nurealm.net>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- self-test failure of crc32c on powerpc
- regressions of ecb(aes) when used with xts/lrw in s5p-sss
- a number of bugs in the omap RNG driver
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: s5p-sss - Fix spinlock recursion on LRW(AES)
hwrng: omap - Do not access INTMASK_REG on EIP76
hwrng: omap - use devm_clk_get() instead of of_clk_get()
hwrng: omap - write registers after enabling the clock
crypto: s5p-sss - Fix completing crypto request in IRQ handler
crypto: powerpc - Fix initialisation of crc32c context
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random updates from Ted Ts'o:
"Change get_random_{int,log} to use the CRNG used by /dev/urandom and
getrandom(2). It's faster and arguably more secure than cut-down MD5
that we had been using.
Also do some code cleanup"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: move random_min_urandom_seed into CONFIG_SYSCTL ifdef block
random: convert get_random_int/long into get_random_u32/u64
random: use chacha20 for get_random_int/long
random: fix comment for unused random_min_urandom_seed
random: remove variable limit
random: remove stale urandom_init_wait
random: remove stale maybe_reseed_primary_crng
|
|
The INTMASK_REG register does not exist on EIP76. Due to this, the call:
omap_rng_write(priv, RNG_INTMASK_REG, RNG_SHUTDOWN_OFLO_MASK);
ends up, through the reg_map_eip76[] array, in accessing the register at
offset 0, which is the RNG_OUTPUT_0_REG. This by itself doesn't cause
any problem, but clearly doesn't enable the interrupt as it was
expected.
On EIP76, the register that allows to enable the interrupt is
RNG_CONTROL_REG. And just like RNG_INTMASK_REG, it's bit 1 of this
register that allows to enable the shutdown_oflo interrupt.
Fixes: 383212425c926 ("hwrng: omap - Add device variant for SafeXcel IP-76 found in Armada 8K")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The omap-rng driver currently uses of_clk_get() to get a reference to
the clock, but never releases that reference. This commit fixes that by
using devm_clk_get() instead.
Fixes: 383212425c926 ("hwrng: omap - Add device variant for SafeXcel IP-76 found in Armada 8K")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Commit 383212425c926 ("hwrng: omap - Add device variant for SafeXcel
IP-76 found in Armada 8K") added support for the SafeXcel IP-76 variant
of the IP. This modification included getting a reference and enabling a
clock. Unfortunately, this was done *after* writing to the
RNG_INTMASK_REG register. This generally works fine when the driver is
built-in because the clock might have been left enabled by the
bootloader, but fails short when the driver is built as a module: it
causes a system hang because a register is being accessed while the
clock is not enabled.
This commit fixes that by making the register access *after* enabling
the clock.
This issue was found by the kernelci.org testing effort.
Fixes: 383212425c926 ("hwrng: omap - Add device variant for SafeXcel IP-76 found in Armada 8K")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
